垂直轴风力机两种翼型气动性能比较研究

叶片是风力机最重要的组成部分,在不同的风能资源情况下,翼型的选择对垂直轴风力机气动特性有着重要的影响。文章分别以NACA0018翼型(对称翼型)和NACA4418翼型(非对称翼型)建立3叶片H型垂直轴风力机二维仿真模型。应用数值模拟的研究方法,从功率系数、单个叶片切向力系数等方面比较两种风力机模型在不同叶尖速比下的气动特性,并采用风洞实验数据验证了流场计算的准确性。CFD计算结果表明:在低叶尖速比下,NACA4418翼型风力机气动特性优于NACA0018翼型风力机,适用于低风速区域;在高叶尖速比下,NACA0018翼型风力机气动特性较好,适用于高风速地区。而且在高叶尖速比时,NACA0018翼型在上风区时,切向力系数平均值要高于NACA4418翼型,在下风区时,NACA418翼型切向力系数平均值高。该研究可为小型垂直轴风力机翼型的选择提供参考。     

有弯度翼型垂直轴风力机的数值模拟研究

应用计算流体动力学有限体积法SIMPLE算法,配合SST k-ω湍流模型和滑动网格技术模拟分析了有弯度翼型4叶片垂直轴风力机的气动特性,以其作为有弯度翼型垂直轴风力机设计的参考依据。研究结果发现,在入口流速为10 m/s,尖速比为1.6时,该种风力机单个叶片的瞬时力矩系数为-0.03～0.18,并且在一个转动周期内正的瞬时力矩系数历时较长;整个风轮的的力矩系数在尖速比为1.6左右时达到最大值,功率系数在尖速比为1.7左右时达到最大值。     

不同扩散体对建筑增强型垂直轴风力机气动性能的影响

为研究不同建筑扩散体对建筑增强型直线翼垂直轴风力机的气动性能与流场结构的影响,采用CFD数值模拟的方法,以NACA0021为叶片翼型的多叶片建筑增强型直线翼垂直轴风力机为对象,研究其在不同建筑扩散体及不同尖速比下的气动性能。结果表明:建筑增强型直线翼垂直轴风力机存在最佳尖速比;不同建筑扩散体对提高直线翼垂直轴风力机风能利用率影响较大,在所选取的8种建筑扩散体模型中,梯形建筑扩散体下的直线翼垂直轴风力机在尖速比为4.62时标准化风能利用率可达1.560 7,而A1翼型式建筑扩散体下的直线翼垂直轴风力机前后压差较小,风能难以利用。     

导流式翼缝对直线翼垂直轴风力机气动性能的影响

为减小流体从吸力面流至压力面的速度损失,基于小间距翼缝有助于减小气动损失的设计原理,针对NACA0021翼型,提出双侧导流式、内导流式和外导流式3种新型翼缝形式。通过数值模拟方法,分析不同翼缝对垂直轴风力机气动性能和流场结构的影响,并将其性能参数与原始翼型和非圆弧翼缝翼型进行对比。结果表明:内导流式翼缝风力机气动性能优于原始风力机,最佳尖速比减小8.06%,改善了叶片周围和整机流场结构,增强了风力机运行稳定性;在低尖速比下,双侧导流式翼缝风力机气动性能较高,而高尖速比时气动性能低于原始风力机;下游区叶片迎风速度较低,外导流式翼缝对流动分离现象改善效果不明显,导致气动性能较差;非圆弧翼缝的间距过大使最大风能利用系数降低了15.5%,不适用于直线翼垂直轴风力机。     

CFD study of some factors affecting performance of HAWT with swept blades

Most modern high-power wind turbines are horizontal axis type with straight twisted blades. Upgrading power and performance of these turbines is considered a challenge. A recent trend towards improving the horizontal axis wind turbine (HAWT) performance is to use swept blades or sweep twist adaptive blades. In the present work, the effect of blade curvature, sweep starting point and sweep direction on the wind turbine performance was investigated. The CFD simulation method was validated against available experimental data of a 0.9?m diameter HAWT. The wind turbine power and thrust coefficients at different tip speed ratios were calculated. Flow field, pressure distribution and local tangential and streamwise forces were also analysed. The results show that the downstream swept blade has the highest C_p value at design point as compared with the straight blade profile. However, the improvement in power coefficient is accompanied by a thrust increase. Results also show that the best performance is obtained when the starting blade sweeps at 25% of blade radius for different directions of sweep.     

TMT40.3大型风力机叶片气动性能分析

基于BLADED软件平台,对TMT40.3大型风力机叶片的气动性能进行了分析.分析结果表明:TMT40.3大型风力机叶片应用在GL3A风场时的额定功率能达到1 650 kW,所承受的疲劳强度和极限载荷均能满足该款风力机叶片的设计要求,在叶尖速比为7.8～11.4的风能利用系数均在0.46以上,最高可达0.486,具有较好的气动性能和较宽的风速适应范围.     

基于叶片变形偏航下风力机叶片绕流流场的研究

针对偏航工况下风力机叶片与流场之间的相互作用而产生的变形影响叶片绕流流场问题,基于叶片变形对不同偏航工况下水平轴风力机叶片绕流流场进行双向流固耦合数值计算,分析偏航工况对风力机叶片变形和表面应力的影响,在此基础上研究不同偏航工况对叶片绕流流场的影响.结果表明,不同叶片上的变形和应力呈现不均匀性,且随偏航角增大,不均匀性...     

L型叶尖小翼对风力机性能影响的研究

采用标准的k-ε湍流模型对添加L型叶尖小翼叶片与原叶片在不同风速条件下进行三维流场的数值研究。通过分析叶尖区域流场和压力分布得到:对比原叶片,L型小翼对通过叶尖的气流具有导流作用,使通过叶尖的气流变得平缓流畅,同时小翼能有效改善叶尖吸力面的气流分离,使得气流分离位置远离叶片前缘,减小压差阻力。L型叶尖小翼加大叶尖部位吸力面与压力面的压差,增大风轮转矩,使风力机出力增加。添加L型小翼后,风力机推力系数最大增幅为0.81%,风力机功率最大增幅为4.2%。     

格尼襟翼垂直轴风力机风场研究

为研究垂直轴风力机风场中机组气动性能受格尼襟翼的影响,采用TSST湍流模型对直线翼垂直轴风力机进行数值模拟研究.结果表明:风场上游风力机组尖速比越大,机组间流体加速效果越显著,使风力机组气动性能高于单风力机;在中低尖速比时,格尼襟翼可有效提升单个风力机气动效率,在尖速比较高时,提升效果并不明显;在风力机组中安装格尼襟翼...     

Performance analysis of the airfoil-slat arrangements for hydro and wind turbine applications

Standard airfoils historically used for wind and hydrokinetic turbines had maximum lift coefficients of around 1.3 at stall angles of attack, which is about 12°. At these conditions, the minimum flow velocities to generate electric power were about 7 m/s and 2 m/s for the wind turbine and the hydrokinetic turbine cases, respectively. In this study, NACA4412-NACA6411 slat–airfoil arrangement was chosen for these two cases in order to investigate the potential performance improvements. Aerodynamic performances of these cases were both numerically and experimentally investigated. The 2D and 3D numerical analysis software were used and the optimum geometric and flow conditions leading to the maximum power coefficient or the maximum lift to drag ratio were obtained. The maximum lift to drag ratio of 24.16 was obtained at the optimum geometric and flow parameters. The maximum power coefficient of 0.506 and the maximum torque were determined at the tip speed ratios of 5.5 and 4.0 respectively. The experimental work conducted in a towing tank gave the power coefficient to be 0.47 which is about %7 lower than the numerical results obtained. Hence, there is reasonable agreement between numerical end experimental values. It may be concluded that slat-hydrofoil or airfoil arrangements may be applied in the design of wind and hydrokinetic turbines for electrical power generation in lower wind velocities (3–4 m/s) and current velocities (about 1 m/s).     

定常吸气对垂直轴风力机性能影响研究

定常吸气装置可有效提高垂直轴风力机气动性能,改善风轮流场结构及翼型动态失速特性.基于CFD方法对垂直轴风力机进行数值模拟,研究不同叶尖速比(TSR)下定常吸气对风力机气动及流场特性的影响,对比分析原始风力机及定常吸气作用下的风能利用率、整机转矩系数及涡量分布.结果表明:不同尖速比下定常吸气均可显著提高风力机气动性能,减...     

浅析水平轴风力机叶片设计叶尖速比的选择

设计叶尖速比是风力机叶片设计中需要考虑的重要因素,文中分析了叶尖速比对叶片的弦长、载荷、气动性能、整机的功率和发电量等的影响,讨论了设计叶尖速比的选择。并分析得出增大设计叶尖速比,能够减小叶片弦长、载荷、成本,提高气动性能,但会使机组发电量有所下降的结论。     

基于CFD的二维垂直轴风力机性能计算

采用计算流体力学方法(CFD)针对垂直轴风力发电机,开展简化的二维绕流特性研究。首先,基于开放型转子和增强型转子,研究网格节点数和壁面y+、计算时间步长和湍流模型等的变化对计算结果的影响,对计算模型和方法进行确认。随后,计算分析增强型垂直轴风力机与开放型垂直轴风力机的特性。结果表明,与开放性垂直轴风力发电机相比,增强型垂直轴风力发电机的功率系数和转矩系数有明显增加,且达到最大值的位置向叶尖速比增大的方向移动。然后对增强型垂直轴风力机发电机在不同来流风速下进行计算,发现增强型垂直轴风力发电机的转子转矩随来流风速增加,而转矩系数和功率系数与来流风速无关。最后,针对定子叶片在不同的方向开展计算研究。结果表明,定子叶片在不同方向时,增强型垂直轴风力机的转子转矩不同,且转矩到达峰值的位置也不同;在当前3个方向角中,叶片处于0°方向角时风力机具有最高的转矩系数,即具有最佳的功率系数。     

全向导叶作用下叶片实度对垂直轴风力机气动特性的影响

为研究全向导叶作用下不同实度对垂直轴风力机气动性能的影响,通过改变叶片数及弦长调整实度并分析其对全向导叶垂直轴风力机气动性能的作用。结果表明：全向导叶使垂直轴风力机周围流体提速效果显著,最大风能利用率和力矩系数较原始垂直轴风力机分别提高41.6%和25%;随实度增大时,全向导叶垂直轴风力机最佳尖速比降低;改变弦长时,风能利用率峰值随弦长增大呈现先增后减的趋势,且在小尖速比工况下,高实度全向导叶垂直轴风力机力矩系数较高,最大可达0.192;改变叶片数时,风能利用率峰值随叶片数增多而降低,且大尖速比下的低实度全向导叶垂直轴风力机力矩系数较大,但不同实度的全向导叶垂直轴风力机最大力矩系数相差较小。     

叶片转角对小型Savonius风机气动性能的影响

Savonius风机是一种典型的垂直轴风力发电机,通过对其进行流固耦合分析,研究叶片转角对风机气动性能的影响。利用ANSYS的CFX流体模块,流体湍流模型选择基于RANS的标准k-ε湍流模型,对风轮进行流固耦合分析,从而获得叶片产生的力矩情况,并计算了风机的功率特性。利用求解结果,得到了力矩系数与叶片转角之间的关系。分析了风机叶片在旋转一周中所产生的最大扭矩以及负扭矩所处的位置和范围。通过分析转角对风机性能的影响,可为今后的Savonius风机叶片形状优化和效率提升提供参考。     

Optimization of cycloidal water turbine and the performance improvement by individual blade control

This paper investigates an advanced vertical axis turbine to enhance power generation from water energy. The turbine, known as a cycloidal water turbine, is a straight-bladed type adopting a cycloidal blade system that actively controls the rotor blades for improved turbine efficiency, according to the operating conditions. These characteristics enable the turbine to self-start and produce high electric power at a low flow speed, or under complex flow conditions. A parametric study has been carried out by CFD analysis, with various characteristics including different number of blades, chord length variations, variety of tip speed ratios, various hydrofoil shapes, and changing pitch and phase angles. Optimal parameters have been determined, and the performance of the turbine has achieved approximately 70% better performance than that of a fixed pitch turbine. An experimental study has also been carried out which shows that the results correlate quite well with the theoretical predictions although the power output was reduced due to the drag forces of the mechanical devices. Another numerical optimization was carried out to improve the rotor performance by adopting an individual blade control method. Controllable pitch angles were employed to maximize the rotor performance at various operating conditions. The optimized result obtained using genetic algorithm and parallel computing, shows an improvement in performance of around 25% compared with the cycloidal motion.     

新型变桨立轴风力机涡效应分析

该文旨在通过变桨来改善升力型立轴风力机叶片气动特性,提高风力机最大运行效率。针对设计尖速比下风能利用系数较低的问题,提出减小叶片小攻角范围,增大叶片大攻角工作范围,以重点改善叶片低性能区域的气动特性为出发点,提高风能利用系数新变桨思路。以采用NACA0012翼型、2 m高和2 m旋转直径的两叶片H型风力机为研究对象,从涡理论来分析和比较在最佳尖速比为5的条件下,附着涡、尾随涡、脱体涡和桨距角对攻角、切向力和功率输出的影响规律。研究结果表明:变桨后,叶片的攻角、切向力和输出功率在原最大值两侧均有明显提高,拓宽了叶片高性能的工作区域;涡系中脱体涡对叶片气动特性影响最大,其中在上盘面影响较小,在下盘面影响较大;变桨前后涡系对上盘面的差异较小,对下盘面的影响差异较明显;变桨后,下盘面的叶片的涡尾迹弯曲程度在加大。     

遗传算法在水平轴洋流机叶片优化设计中的应用

水平轴洋流机是捕获洋流能的主要设备,其叶片外形直接影响捕能效率。通过Bezier参数化曲线描述定速定桨距洋流机的叶片弦长和扭角分布规律,采用叶素-动量理论计算其水动特性。以额定流速下能量利用系数系数最大为目标,基于遗传算法建立了叶片外形优化模型。同时,为了避免因汽蚀导致功率输出不稳定的现象,在优化过程中以汽蚀作为约束条件,与经典设计方法Wilson理论设计叶片进行了比较。结果表明:优化叶片在叶根处的扭角更小,具有更佳的抗扭性能;叶根和叶尖处弦长均更小,节省了材料;在设计流速范围内,优化叶片在低流速下效率更高,平均提高了4.6%,具有更好的启动性能。     

Research on wind turbine rotor models using NACA profiles

In this study, rotation rates and power coefficients of miniature wind turbine rotor models manufactured using NACA profiles were investigated. For this purpose, miniature rotor models with 310 mm diameter were made from “Balsa” wood. When all properties of rotor models were taken into account, a total of 180 various combinations were obtained. Each combination was coded with rotor form code. These model rotors were tested in a wind tunnel measurement system. Rotation rates for each rotor form were determined based on wind speed. Power coefficient values were calculated using power and tip speed rates of wind. Rotor models produced a rotation rate up to 3077 rpm, with a power coefficient rate up to 0.425. Rotor models manufactured by using NACA 4412 profiles with 0 grade twisting angle, 5 grade blade angle, double blades had the highest rotation rate, while those manufactured by using NACA 4415 profiles with 0 grade twisting angle, 18 grade blade angle, 4 blades had the highest power coefficient.     

The near wake of a model horizontal-axis wind turbine—II. General features of the three-dimensional flowfield

The three-dimensional near-wake of a model horizontal-axis wind turbine has been measured for three operating conditions: stalled flow over the blades, close to optimum performance, and approaching runaway. The measurements of the mean velocity and turbulence at six axial locations document the formation and development of the near-wake. For the two highest tip speed ratios, the tip vortices are clearly identifiable from the contours of axial velocity and vorticity, and turbulent kinetic energy. At the lowest tip speed ratio, the turbulence level is also high within the blade wakes and these wakes are larger, because of separation in the flow over the blades. The wake structure is simplest for the condition closest to the optimum where the bound vorticity is almost constant with radius. As the tip speed ratio increases, the pitch of the tip vortices decreases and the angular momentum within them increases. This angular momentum reduces the power available from the turbine. The implication is that the structure of the tip vortices must be included in computational models intended to cover the entire operating range of a turbine.