Effect of doped Mn on piezoelectric properties of （Na0.5Bi0.5 ）0.92 Ba0.08 TiO3 lead-free ceramics

Piezoelectric ceramics (Na0.5Bi0.5)0.92Ba0.05TiO3 x%MnCO3(BNBT-Mn, x=0-1.6,mass fraction)were synthesized by conventional solid state reaction. The results show that when the addition of MnCO3 is 0-1.4%, BNBT-Mn ceramics exhibit a single-phase perovskite structure. With the increase of content of MnCO3, piezoelectric constant and electromechanical coupling factor increase rapidly when x is lower than 0.3. Then they both decrease when x is in the range of 0.3 and 1.6. When x=0.3, piezoelectric constant and electromechanical coupling factor reach the maximum value of 160 pC/N and 58.5% respectively, which can improve the temperature stability of BNBT-Mn.     

Effect of Li content on the microstructure and properties of lead-free piezoelectric （K0.5Na0.5）1-xLixNbO3 ceramics prepared by SPS

Lead-free piezoelectric （K0.5sNa0.5）1-xLixNbO3 （x = 0at%-20at%） ceramics were synthesized by spark plasma sintering （SPS） at low temperature and the effects of LiNbO3 addition on its crystal structure and properties were also studied. When the Li content was less than 6at%, a single proveskite phase with the similar structure of （K0.5Na0.5）NbO3 was formed; and a secondary phase with K3Li2Nb5O15 structure was observed in the 6at% 〈 x 〈 20at% compositional range. Furthermore, LiNbO3 existed as the third phase when the Li content was higher than 8at%. The grain sizes increased from 200-500 nm to 5-8 μm when the K3Li2Nb5O15 and LiNbO3 like phases were formed. With increasing Li content, the relative density of the ceramics first decreased from 97% to 93% and then kept constant. The piezoelectric coefficient d33, dielectric constant, and planner electromechanical coupling factor exhibited a decreasing tendency with increasing Li content because of the decrease in density and the formation of the secondary phase such as K3Li2Nb5O15 and LiNbO3. The formation of dense microstructure with a single phase is necessary in improving the properties of the （K0.5Na0.5）1-xLixNbO3 ceramics.     

Synthesis and Piezoelectric Properties of Lead-free （ Bi0.5 Na0.5 ）1-x（BaaSrb）xTiO3 Ceramics

A new group of lead-free piezoelectric ceramics,（Bi0.5 Na0.5）1-x（BaaSrb）xTiO3（abbreviated as BNBST[100x-100a/100b],0〈x〈1,a＋b=1）,was synthesized.The ceramics were prepared by conventional ceramic sintering technique,and the ceramics with density of 95% of the theoretical one can be sintered without the atmosphere control during the sintering process.The results of the X-ray diffraction（XRD） data show that the ceramics possess a single perovskite phase.The measurements of dielectric and piezoelectric properties reveal that the ceramics provide relatively high piezoelectric charge constant d33 and high planar electromechanical coupling factor kp.For the BNBST6-95/5 ceramics,d33 is equal to 170pC/N,and kp is equal to 32.0%.The fabrication technique for these ceramics is conventional and stable.     

Bi1/2Na1/2TiO3-Bi1/2Na1/2(Nb2/3Zn1/3)O3-BaTiO3无铅陶瓷压电介电性能

采用传统陶瓷制备方法,制备出新型无铅压电陶瓷,并对该体系无铅陶瓷的相结构、介电和压电性能进行了研究.结果表明:所研究的组成均能够形成纯钙钛矿(ABO3)型固溶体;随着BaTiO3含量的增加,压电系数d33先增大后减小.同时陶瓷材料的介电常数-温度曲线显示该体系材料具有明显的弛豫铁电体特征.     

La2O3掺杂对(Bi1/2Na1/2)0.94Ba0.06TiO3陶瓷性能与微结构的影响

采用传统陶瓷工艺方法制备了La2O3掺杂(Bi1/2Na1/2)0.94Ba0.06TiOa(BNBT6)无铅压电陶瓷,系统地研究了La2O3掺杂对该体系陶瓷介电、压电性能与微观结构的影响.结果表明:该体系具有很高的压电常数,是单一的钙钛矿结构,La2O3的添加对晶粒生长具有一定的抑制作用,线收缩率和相对密度增大.室温介电常数随着La2O3掺杂量的增加而增大.与不添加La2O3的陶瓷样品相比,添加少量La2O3可以使体系的弛豫特征更为明显.当掺杂量为0.1 wt%时,该体系陶瓷具有较好的综合性能:d3a=160 pC/N,kp=0.322.当掺杂量达到0.5 wt%以后,陶瓷的压电性能严重降低.     

Microstructure, crystalline phase and electrical properties of Li0.06（Na0.5K0.5）0.94Nb（1-2x/5）MgxO3 lead-free piezoelectric ceramics

MgO-modified Li0.06(Na0.5K0.5)0.94NbO3(L6NKN) lead-free piezoelectric ceramics were synthesized by normal sintering at a relatively low temperature of 1000°C.The crystalline phase,microstructure,and electrical properties of the ceramics were investigated with a special emphasis on the influence of MgO content.The addition of MgO effectively improves the sinterability of the L6NKN ceramics.X-ray diffraction analysis indicates that the morphotropic phase boundary(MPB) separating orthorhombic and tetragonal ph...     

Bi0．5Na0．5TiO3无铅压电陶瓷的结构有序化控制

以片状SrTiO3晶粒作为模板,使用模板晶粒生长法（TGG）控制制备[001]取向的有序化Bi0.5Na0.5TiO3压电陶瓷,同时研究了过量Bi2O3烧结温度以及掺MnO对Bi0.5,Na0.5TiO3有序度的影响．研究结果表明,过量Bi2O3的最佳掺入量为BNT粉料质量的1％;1190℃是合适的烧结温度,在1190℃下,BNT-1试样的有序度相对较高,有序度为88．2％;MnO的加入有效地提高了试样的有序度,并且降低了试样的烧结温度,同时也使得烧结温度范围变窄．在烧结温度为1170℃下,掺质量分数为0．3％MnO的BNT-1试样的有序度为91．1％．     

纳米Na0.5Bi0.5TiO3粉体的水热合成研究

以Bi(NO3)3·5H2O、Ti(OC4H9)4为原料,研究和分析了水热条件下Na0.5Bi0.5TiO3(BNT)晶体生长和形成的影响因素.结果表明,在反应温度为160～180℃,保温时间为4～16h,NaOH浓度为4～12mol/L的条件下可制备出高纯度的纳米Na0.5Bi0.5TiO3粉体,其颗粒尺寸约为15～60nm.     

Synthesis and Piezoelectric Properties of Lead-free (Bi_(0.5)Na_ (0.5))_ 1-x(Ba_aSr_b)_xTiO_3 Ceramics

planarelectromechanicalcouplingfactor;piezoelectricchargeconstant1Introduction Leadoxide basedpiezoelectricceramics,suchasPb(Ti,Zr)O3(PZT),arenowwidelyusedinvariousappli cationssuchastransducers,filters,oscillatorsandactua torsbecauseoftheirsuperiorpiezoe…     

Struchre and Electrical Properties of (Na0.5Bi0.5)0.94Ba0.06TiO3 Ceramic with 0.5 wt% of MnO

The structure and electrical properties of(Na0.5Bi0.5)0.94Ba0.06TiO3 ceramic doped with 0.5 wt% of MnO were investigated in comparison with those of(Na0.5Bi0.5)0.94Ba0.06TiO3 ceramic.It was ascertained that the MnO addition did not cause remarkable change in crystal structure and microstructure.The MnO addition mainly displayed a hard effect on the electrical properties,an increase of coercive field(Ec)and mechanical quality factor(Qm)together with a decrease of dielectric constant(?r)and piezoelectric constant(d33).An enhancement of electromechanical coupling factor(kp)with the MnO addition was obtained too.An essential relation between the piezoelectric properties and ferroelectric nature of the ceramics was detected.It was found that the piezoelectric properties of the ceramics highly depended on the corporative contribution of remanent polarization(Pr)and coercive field.     

Enhanced piezoelectric properties of Nd^3＋ doped nano-lead zirconate titanate piezoelectric ceramics

Nd^3＋ doped lead zirconate titanate （Pb1-3x/2NdxZr0.52Ti0.48O3, PNZT） nanopowders were prepared through a modified sol-gel method. The effects of Nd^3＋ doping on the microstructures and properties of PNZT ceramics have been studies. The grain sizes of the perovskite PNZT nanopowders were about 100nm and the lattice distortion of the PNZT increased with the content of Nd^3＋ up to 9 mol%. The dopant of Nd^3＋ resulted in the decrease of crystal lattice parameter a and the obvious increase of c and c/a, which effectively improved the sintered densification and activity of the PNZT ceramics. Due to lead vacancies caused by the doping of Nd3^＋ in the PZT, the piezoelectric constant, electromechanical coupling coefficient and dielectric constant observed were much higher than the monolithic PZT.     

Effect of sintering aid CuO-MnO2 on dielectric properties of 0.5Ba(Mg1/3Nb2/3)O3-0.5Ba(Ni1/3Nb2/3)O3 ceramics

Microstructures and microwave dielectric properties of 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics with x wt% CuO−x wt% MnO₂ additions (x=0.25–1) prepared by conventional solid-state route were investigated. It is found that low level-doping of CuO-MnO₂ can significantly improve the density of the specimens and their microwave dielectric properties. The relative density of 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics can be increased by 95% sintering at 1 330 °C due to the liquid phase effect. The second phase is not observed in ceramics with CuO-MnO₂ addition. The parameter ε _r increases with increasing sintering temperature, and Q _f is effectively promoted by CuO-MnO₂ addition. Higher CuO-MnO₂ content would make τ_f value more positive. Meanwhile, ε _r value of 30.5, Q _f value of 63 200 GHz and τ _f value of 0.5 ppm/°C were obtained for 0.5Ba(Mg_1/3Nb_2/3)O₃-0.5Ba(Ni_1/3Nb_2/3)O₃ ceramics with 0.5 wt% CuO-0.5 wt% MnO₂ addition sintered at 1 330 °C for 4 h.     

0．992K0．5Na0．5NbO3-0．008BiFeO3无铅压电陶瓷制备及压电性能研究

以水热法制备的0．992K0．5Na0．5NbO3（BF）粉体等为原料,采用常压烧结法在1065℃下烧结2h制备了0．992K0．5Na0．5NbO3-0．008BiFe03无铅压电陶瓷,并研究了BiFeO3掺杂对0．992K0．5Na0．5NbO3-0．008BiFeO3无铅压电陶瓷结构和压电的影响．研究结果表明：BiFeO3掺杂使K0.5Na0.5NbO3无铅压电陶瓷正交相减弱,晶粒尺寸由6／2m减小到1μm;压电性能有一定提高,压电常数（d33）、机电耦合系数（kp）分别达到120pC／N和37．8,居里温度Tc由444．4℃减少至420．6℃．     

(Na_(0.5)K_(0.5))NbO_3基无铅压电陶瓷压电常数的研究

针对目前无铅压电陶瓷的压电常数d33偏小的情况,采用传统的烧结方法制备了(Na0.5K0.5)NbO3基无铅压电陶瓷(Na0.5K0.45Li0.05)Nb0.95-xSbxTa0.05O3(x=0.03,0.06,0.09,0.12),研究了在Li和Ta含量固定的情况下,Sb元素的添加量和烧结温度对陶瓷的压电常数的影响.研究结果表明,适量Sb元素的掺杂可以大幅度提高陶瓷的压电常数d33,陶瓷样品的压电常数d33随着Sb含量的增加先增大后减小.烧结温度可以影响陶瓷的密度,进而影响其压电常数.在1130℃的最佳烧结温度下,Sb含量x=0.09时,陶瓷样品表现出最佳的压电性能,压电常数d33=328 pC/N.     

Effect of Lead Contents on the Properties of PMSZT Piezoelectric Ceramics

The effects of Pb content on crystallographic phase, microstructure, electric-properties of PMSZT piezoelectric ceramics were studied. The crystallographic phase and microstructure of the ceramics were examined by using X-ray diffraction （XRD） and scanning electron microscopy （SEM）. The experimental result shows that the samples consist of a mixture of tetragonal and rhombohedral phases in the range of lead contents x=0.95-1.06, grains grow up homogeneously and the minimum value of Curie temperature was obtained with x-=1.02. With Pb content x〈l.02 or x〉1.02, the Curie temperature moves towards a high temperature. A well-situated electric-properties of ET33/E0 （1660）, d33 （344pC/N）, Kp （0.684）, Qm （2350）,tan 3（0.0030） were obtained when lead content x=1.02.     

Microstructures and Electrical Properties of Bi_(0.5)-(Na_(1-x-y)K_xLi_y)_(0.5)TiO_3 Lead-free Piezoelectric Ceramics

The microstructures and electrical properties of Bi0.5(Na1-x-yKxLiy)0.5TiO3 lead-free piezoelectric ceramics were studied.These ceramics were prepared by conventional ceramic technique.XRD analysis reveals that the ceramics possess almost pure perovskite phase when y≤0.2.The SEM results show that,with more amounts of Li+,the crystalline grain growing speed is accelerated,and the sintering temperature can effectively be decreased.The measurements of piezoelectric properties indicate that the ceramics with relatively low amount of Li+ and high amount of K+ have comparatively large piezoelectricity.The dielectric measurements show that the ceramics have properties like relaxor ferroelectrics and diffuse phase transition(DPT) at Td and Tc,respectively.The results of ferroelectric measurements reveal the system has relatively higher remanent polarization Pr(27.6 μC/cm2) and lower coercive field Ec(37.5 kV/cm).     

(Bi_(1/2)Na_(1/2))_(1-x)Ba_xTiO_3系无铅压电陶瓷的现状

综述了(Bi1/2Na1/2)1-xBaxTiO3系无铅压电陶瓷的最新研究进展。简述了A位非化学计量改性及几种较成功的掺杂改性方法。将A位掺杂(如La3+)、B位掺杂(如Co3+、Nb5+)以及综合掺杂(如Ce3+、Ce4+)的优缺点和掺杂机理进行了归类比较。解释了各系统中相应掺杂引起性能变化的原因,为进一步开展无铅压电陶瓷的研究提供参考。     

Dielectric and Piezoelectric Properties of 0-3 PZT/PVDF Composite Doped with Polyaniline

Lead zirconate titanate （ PZT ） / polyvinylidene fluoride （PVDF） 0-3 piezoelectric composites doped with polyaniline （PANI） were obtained by hot-press method. The polarization properties of the composites were characterized by XRD and P- E hysteresis loops at room temperature. And the dielectric and piezoelectric properties were also measured. The results show that the poling of PZT could be effectively carried oat and the dielectric constant e, and dissipation tanδ increase monatonously by increasing the volume fraction of PANI in the composite. The piezoelectric constant d33, and the planar electromechanical coupling factor kp increase while the mechanical quality factor Qm decreases with the increase in the content of PANI. The d33, kp and Qm show the extremum values at 8 vol%-10 vol% PANI.     

（Ba，Eu）Ti03细晶粒陶瓷制备中的影响因素

采用冷压陶瓷技术,分别在1400℃和1300℃制备了具有四方结构的（Ba1-xEu）TiO3和（Ba1-xEu）Ti1-x／80,陶瓷．应用x射线衍射（XRD）、扫描电子显微镜（SEM）和原子力显微镜（AFM）研究Eu含量、n空位缺陷和陶瓷化烧结温度的变化对制备（Ba,Eu）TiO,细晶粒陶瓷的影响因素．结果表明：当z=0．05时,1300＇1：制备的（Ba1-xEu）Ti,-x／80,陶瓷细化到平均晶粒尺寸小于1μm,1400℃制备的（BahEu,）Ti03陶瓷却畸变生长到5斗m．而x=0．03时,（Ba1-xEu）TiO,陶瓷仍能细化到1μm．说明较高的陶瓷化烧结温度并不是晶粒生长的主要原因,Ti空位的存在起到抑制晶粒生长的作用．x≥0．07时,（Ba1-xEu）TiO,陶瓷为大于5斗m的粗晶粒陶瓷,说明Eu含量的继续增加不能抑制晶粒生长．     

Ce4+及La3+掺杂对(Bi0.5Na0.5) Ba0.06TiO3 陶瓷压电性能的影响

采用固相法制备工艺制备了质量分数CeO2(0-0.6%)和La2O3(0-1.3%)掺杂的(Bi0.5Na0.5)0.94Ba0.06TiO3(BNBT6)无铅压电陶瓷.研究了合成产物的晶体结构、压电性能以及压电常数温度稳定系数.结果表明:所有组成均呈三方结构的钙钛矿型固溶体特征;当CeO2掺杂量为质量分数0.4%、La2O3掺杂量为质量分数1.0%时,陶瓷具有较好的压电性能,与纯BNBT6相比,分别提高了12%和15%;2种掺杂离子均能够改善陶瓷材料压电性能的温度稳定性.