Auslegung von pulsierten Siebboden‐ und Sprühkolonnen für die Extraktion auf der Basis von Einzeltropfenuntersuchungen

The design of pulsed sieve‐plate extraction columns (PSE) on the basis of published data is not currently possible as it relais on additional and cost intensive laboratory experiments. This is due to the lack of knowledge about the complex mass transfer between two liquid phases which is strongly influenced by factors such as surface active impurities and the Marangoni‐effect. In order to reduce the experimental effort in the determination of the required design input data, several standard experimental test units have been developed at the Institut für Thermische Verfahrenstechnik that allow the determination of the needed fluiddynamic and mass transfer data. The test units are based on single drop experiments, and they use the technical mixture to be separated in practice. Finally, the meas ured mass transfer and fluiddynamic data are used to calculate the drop‐size‐, holdup‐ and concentration‐profiles for the systems toluene‐ace tone‐water and n‐butylacetate‐ace tone‐water in a PSE‐column and a spray‐column. The results are compared with experimental data reported in the literature and our own data obtained with a semi‐industrial PSE‐column.     

Hydrierung von p‐Nitrophenol zu p‐Aminophenol als Testreaktion für die katalytische Aktivität von Pt‐Trägerkatalysatoren

The hydrogenation of p‐nitrophenol (PNP) to p‐aminophenol (PAP) using NaBH₄ as a reducing agent was studied as a test reaction for determining the catalytic activity of supported Pt catalysts. The initial reaction rate, which is accessible within less than 10 minutes via online UV‐vis spectroscopy at room temperature, ambient pressure and in water as a solvent, was used as measure for the catalytic activity. For three Pt catalysts supported on porous SiO₂, porous glass and Al₂O₃, respectively, significant differences in the catalytic activity were observed. However, especially in case of very active catalysts, limitations of the reaction by internal or external mass transfer have to be considered.     

Abreicherung von Flüssiggas aus Erdgas mittels Zeolithmembranen

The depletion of higher alkanes from methane is a key aspect during the conditioning of natural gases or accompanying gases. Membrane technologies could be used as alternative to energy and cost intensive purifications. Against this background the influence of membrane geometry, composition of the gas mixture as well as temperature and pressure was investigated in separation experiments for methane/n‐butane mixtures using MFI membranes.     

Master curve and time–temperature–transformation cure diagram of a polyfunctional epoxy acrylic resin

The curing reaction of a well‐defined glycidyl methacrylate‐co‐butyl acrylate statistical copolymer, prepared by atom transfer radical polymerization, and a commercial linear diamine (Jeffamine D‐230) was studied with the objectives of constructing and discussing a time–temperature–transformation isothermal curing for this system. Thermal and rheological analyses were used to obtain the gelation and vitrification times. Differential scanning calorimetry data showed a one‐to‐one relationship between the glass‐transition temperature (T_g) and fractional conversion independent of the cure temperature. As a result, T_g was used as a measurement of conversion. We obtained a kinetically controlled master curve for isothermal curing temperatures from 50 to 100°C by shifting T_g versus the natural logarithm time data to a reference temperature of 80°C. We calculated the apparent activation energy by applying two different methods, gel time measurements versus shift factors, suggesting a good agreement between them. Isoconversion contours were calculated by the numerical integration of the kinetic model. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Non‐Isothermal Kinetic Study of the Thermal Decomposition of Melamine 3‐Nitro‐1,2,4‐triazol‐5‐one Salt

Study on thermal behavior of 3‐nitro‐1,2,4‐triazol‐5‐one (NTO) salts was required to obtain important data for application purposes. These compounds have been shown to be useful intermediates for gun propellant ingredients, high energetic ballistic modifiers for solid propellants and other potential applications. In this paper, thermal decomposition and non‐isothermal kinetics of melamine 3‐nitro‐1,2,4‐triazol‐5‐one salt (MNTO) were studied under non‐isothermal conditions by DSC and TG methods. The kinetic parameters were obtained from analysis of the DSC and TG curves by Kissinger and Ozawa methods. The critical temperature of thermal explosion (T_b) was 574 K. The results show that MNTO is thermally more stable than NTO when compared in terms of the critical temperature of thermal explosion. Finally, the values of ΔS^#, ΔH^#, and ΔG^# of its decomposition reaction were calculated.     

Synthesis and characterization of Pst‐b‐PDMS‐b‐PSt copolymers by atom transfer radical polymerization

Polystyrene‐b‐poly(dimethylsiloxane)‐b‐polystyrene (Pst‐b‐PDMS‐b‐PSt) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). Commercially available difunctional PDMS containing vinylsilyl terminal species was reacted with hydrogen bromide, resulting in the PDMS macroinitiators for the ATRP of styrene (St). The latter procedure was carried out at 130°C in a phenyl ether solution with CuCl and 4, 4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. By using this technique, triblock copolymers consisting of a PDMS center block and polystyrene terminal blocks were synthesized. The polymerization was controllable; ATRP of St from those macroinitiators showed linear increases in M_n with conversion. The block copolymers were characterized with IR and ¹H‐NMR. The effects of molecular weight of macroinitiators, macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3764–3770, 2004     

Viscoelastic behavior of polybutadienes with high 1,4‐microstructure and narrow molecular weight distribution

Polybutadienes (PBs) of narrow molecular weight distributions with high 1,4‐microstructure were synthesized by sec‐butyllithium‐initiated, living polymerization. The shoulder‐like anomalous behavior of the storage modulus G′(ω) in the terminal zone for PBs was studied using size exclusion chromatography (SEC) and rheometric mechanical spectrometry (RMS). It was found that a high‐molecular‐weight fraction in the PBs was the main reason for the occurrence of the shoulders. The linear viscoelastic spectra were successfully obtained by the Pade–Laplace method from experimental dynamic data, using either the dynamic storage, G′(ω), or loss, G"(ω), modulus. Both the dynamic moduli and stress relaxation in the linear regime were then calculated with reasonable precision. The feasibility of time–temperature–molecular weight superposition for PBs using this method was demonstrated. The dependencies of relaxation spectra on temperature and molecular weight were obtained by a fitting procedure. Thus, with a known reference state, the relaxation spectrum for a given molecular weight PB at a given temperature can be predicted. The predicted dynamic moduli are in good agreement with experimental data. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1315–1324, 1999     

Synthesis,effectiveness, and working mechanism of humic acid‐{sodium 2‐acrylamido‐2‐methylpropane sulfonate‐co‐N,N‐dimethyl acrylamide‐co‐acrylic acid} graft copolymer as high‐temperature fluid loss additive in oil well cementing

Monomers of 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS®), N,N–dimethyl acrylamide (NNDMA) and acrylic acid (AA) were grafted on humic acid as backbone by aqueous free radical copolymerization in such a manner that a graft copolymer possessing lateral terpolymer chains was obtained. Molar ratios between AMPS®, NNDMA, and AA were found to be 1 : 1.54 : 0.02 and the ratio between backbone and graft chain was 20 : 80 wt %. The synthesized fluid loss additive (FLA) was characterized by size exclusion chromatography (SEC), charge titration, and Brookfield viscometry. Thermogravimetric and SEC analysis revealed stretched backbone worm architecture for the polymer whereby humic acid constitutes the backbone decorated with lateral graft chains. Grafting was confirmed by SEC data (R_g) and by ineffectiveness of a blend of AMPS®‐NNDMA‐AA copolymer with humic acid. Their performance as high temperature FLA was studied at 150°C by measuring static filtration properties of oil well cement slurries containing 35% bwoc of silica fume and 1.2% bwoc AMPS®‐co‐itaconic acid retarder. At this temperature, 1.0% bwoc graft copolymer achieves API fluid loss value of 40 mL, thus confirming high effectiveness. The graft copolymer viscosifies cement slurries less than other common synthetic FLAs. The working mechanism of the graft copolymer was found to rely on adsorption onto surface of hydrating cement, as was evidenced by adsorption and zeta potential measurements. Adsorption is hardly affected by temperature and results in constriction of the filter cake pores. The study provides insight into performance of cement additives under the harsh conditions of high temperature and high pressure. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermo‐ and pH‐ responsive copolymers: Poly(n‐Isopropylacrylamide‐co‐IAM) copolymers

Poly(N‐isopropylacrylamide) (NIPAAm) is well known as a smart material with good thermal sensitivity and favorable biocompatibility. A series of new smart hydrogels, NIPAAm copolymerized with IAM (itaconamic acid; 4‐amino‐2‐methylene‐4‐oxobutanoic acid), were synthesized through radical solution polymerization in this work. Poly(NIPAAm‐co‐IAM) can respond to the changes of temperature as well as pH value. Such a characteristic is due to the fact that IAM contains not only a hydrophilic acrylic acid moiety but also an acrylamide moiety to be thermal and pH sensitive. The experimental results show that the lower critical solution temperature (LCST) of the copolymer increases as the molar fraction of IAM increases. Moreover, based on the current experimental data, 3 wt % of Poly(NIPAAm‐co‐IAM) aqueous solution in this study exhibits a phase transition temperature (37.8°C) close to the human body temperature in the buffer solution of pH 7 possibly to be useful in drug delivery. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42367.     

Dielectric properties of new fully conjugated 2H‐ and metal‐pyrazinoporphyrazine network polymers

2,7‐Di‐tert‐butylpyrene was oxidized to 2,7‐di‐tert‐butylpyrene‐4,5,9,10‐tetraone. The latter through condensation reaction with vicinal diamine such as diaminomaleodinitrile afforded heterocyclic monomer, 2,7‐di‐tert‐butyl pyrene[4,5][9,10]bis(2,3‐pyrazine‐5,6‐dinitrile), which was cyclotetramerized to the corresponding 2H‐ and metal‐pyrazinoporphyrazine‐based network polymers (2H‐PyzPz and M‐PyzPz, M = Co, Ni, Zn, or Cu). Elemental analytical results, Infrared, and NMR spectral data of the new prepared molecules are consistent with their assigned formulations. Molecular masses and metal contents of the synthesized polymers proved to be of high molecular masses, which confirm the efficiency of tetramerization polymerization and complexation reactions. Dielectric permittivity, ε′, loss tangent, tan δ, and ac conductivity, σac(ω), of 2H‐PyzPz and M‐PyzPz films were studied as a function of temperature and frequency. It was found that dielectric permittivity, ε′, decreases with the increase of frequency and increases with the increase in temperature. Ac conductivity, σac(ω), is found to vary as Bωs and the frequency exponent, s, is less than unity around room temperature indicating a dominant hopping process. On the other hand, σac(T) of all samples is thermally activated with low activation energies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Capillary flow of low‐density polyethylene

The capillary flow of a commercial low‐density polyethylene (LDPE) melt was studied both experimentally and numerically. The excess pressure drop due to entry (Bagley correction), the compressibility, the effect of pressure on viscosity, and the possible slip effects on the capillary data analysis have been examined. Using a series of capillary dies having different diameters, D, and length‐to‐diameter L/D ratios, a full rheological characterization has been carried out, and the experimental data have been fitted both with a viscous model (Carreau‐Yasuda) and a viscoelastic one (the Kaye—Bernstein, Kearsley, Zapas/Papanastasiou, Scriven, Macosko, or K‐BKZ/PSM model). Particular emphasis has been given on the pressure‐dependence of viscosity, with a pressure‐dependent coefficient β_p. For the viscous model, the viscosity is a function of both temperature and pressure. For the viscoelastic K‐BKZ model, the time‐temperature shifting concept has been used for the non‐isothermal calculations, while the time–pressure shifting concept has been used to shift the relaxation moduli for the pressure‐dependence effect. It was found that only the viscoelastic simulations were capable of reproducing the experimental data well, while any viscous modeling always underestimates the pressures, especially at the higher apparent shear rates and L/D ratios. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Fischer‐Tropsch Synthesis Over Co‐Ru/γ‐Al2O3 Catalyst in Supercritical Media

The Fischer‐Tropsch synthesis (FTS) in gaseous and supercritical phases was examined in a continuous, high‐pressure fixed‐bed reactor by employing a cobalt catalyst (Co‐Ru/γ‐Al₂O₃). The kinetic modeling of the FTS was investigated in the reactor over a 60–80 mesh cobalt catalyst. The Langmuir‐Hinshelwood kinetic equation was used for both the Fisher‐Tropsch (FT) and water gas shift (WGS) reactions. The kinetic model was applied for simulation of the reactor with 16–20 mesh cobalt catalyst. The simulation results showed a good agreement with the experimental data. The experimental data showed that higher CO conversion and lower CH₄ and CO₂ selectivities were achieved in supercritical media compared to the gaseous phase. The BET surface area and pore volume enhancement results provided evidence of the higher in situ extraction and greater solubility of heavy hydrocarbons in supercritical media than in gaseous phases. Furthermore, the effects of supercritical solvent such as n‐pentane, n‐hexane, n‐heptane and their mixtures were studied. Moreover, the influence of reaction temperature, H₂/CO ratio, W/F_(CO+H2) and pressure tuning in the supercritical media FT synthesis were investigated, as well as the effect of the supercritical fluid on the heat transfer within the reactor. The product carbon distribution had a similar shape for all types of solvents and shifted to lighter molar mass compounds with increasing temperature, H₂/CO ratio, and W/F_(CO+H2). Finally, the product distribution shifted to higher molar mass hydrocarbons with increasing pressure. As a result, one may conclude that a mixture of hydrocarbon products of the FTS can be used as a solvent for supercritical media in Fischer‐Tropsch synthesis.     

Simultaneous measurement of the molecular weight distribution and 5‐ethylidene‐2‐norbornene content across the molecular weight distribution of ethylene–propylene–diene terpolymer via a new size exclusion chromatography–ultraviolet–refractive index method

A size exclusion chromatography (SEC)–UV–refractive index (RI) method was developed to measure the 5‐ethylidene‐2‐norbornene (ENB) content across the molecular weight distribution (MWD) in ethylene–propylene–diene terpolymer (EPDM) at room temperature. The ratio of the UV and RI signals at the same effective elution volume was converted to ENB content. The feasibility of using this method to measure the ENB content across the MWD in EPDM at high temperature was also demonstrated. Prior understanding was that ENB had insufficient UV absorbance relative to high‐temperature SEC solvents to allow for useful measurements. We demonstrated this by using high‐boiling‐point solvents, such as decalin, with a low UV absorbance in the UV wavelength range of interest for ENB. These solvents also gave rise to a high enough specific RI increment (dn/dc) for EPDM that a suitable RI detector response was obtained. Additionally, this methodology could be readily applied to other polymers soluble at high temperature as long as the polymers contained a UV chromophore. These include polymers containing vinyl, conjugated vinyl, aromatic ring, carbonyl, or halocarbon groups. This UV‐absorption‐based detection concept might also be extended to high‐temperature thermal‐gradient interactive chromatography‐UV, high‐temperature solvent‐gradient interactive chromatography‐UV (high‐temperature liquid chromatography‐UV), temperature‐rising elution fractionation‐UV, crystallization analysis fractionation‐UV, and crystallization elution fractionation‐UV. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43911.     

Synthesis and characterization of degradable copoly(ester–amide)s: Poly(trans‐4‐hydroxy‐L‐proline‐co‐ε‐caprolactam)

Novel copolyesteramides were synthesized by reacting trans‐4‐hydroxy‐N‐benzyloxycarbonyl‐L ‐proline (N‐CBz‐Hpr) with ε‐caprolactam (CLM) in the presence of stannous octoate [Sn(II) Oct.] as a catalyst. Various techniques, including ¹H‐NMR, IR, DSC, and viscosity, were used to elucidate structural characteristics and thermal properties of the resulting copolymers. Data showed that the optimal reaction condition for the synthesis of the copolymers was obtained by using 3 wt % Sn(II) Oct. at 170°C for 24 h. The DSC analysis demonstrated amorphous structure for most of the copolymers. The glass‐transition temperature of the copolymers shifts to a higher temperature with increasing Hpr/CLM molar ratio. In vitro degradation of these poly(N‐CBz‐Hpr‐co‐CLM)s was evaluated by weight loss measurements. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1615–1621, 2002     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Kinetics of Michael addition polymerizations of n,n′‐bismaleimide‐4,4′‐diphenylmethane with barbituric acid

With the addition of sufficient hydroquinone to completely suppress the free radical polymerization, the kinetics of Michael addition polymerizations of N,N′‐bismaleimide‐4,4′‐diphenylmethane (BMI) and barbituric acid (BTA) with BMI/BTA = 2/1 (mol/mol) in 1‐methyl‐2‐pyrrolidone was investigated independently. A mechanistic model was developed to adequately predict the polymerization kinetics before a critical conversion (ca. 60%), at which point the diffusion‐controlled polymer reactions started to predominate in the latter stage of polymerization. The Michael addition polymerization rate constants and activation energy in the temperature range 383–423 K were determined accordingly. Beyond the critical conversion, a relatively stationary limiting conversion (ca. 69%) independent of the reaction temperature was achieved. A diffusion‐controlled polymerization model taken from the literature satisfactorily predicted the limiting conversion data. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Synthesis and characterization of PBMA‐b‐PDMS‐b‐PBMA copolymers by atom transfer radical polymerization

Poly(butyl methylacrylate)–b–poly(dimethylsiloxane)–b–poly(butyl methylacrylate) (PBMA–b–PDMS–b–PBMA) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). The reaction of α,ω‐dichloride PDMS with 2′‐hydroxyethyl‐2‐bromo‐2‐methylpropanoate gave suitable macroinitiators for the ATRP of BMA. The latter procedure was carried out at 110°C in a phenyl ether solution with CuCl and 4,4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. The polymerization was controllable, with the increase of the monomer conversion, there was a nearly linear increase of molecular weight and a decrease of polydispersity in the process of the polymerization, and the rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with IR and ¹H‐NMR and differential scanning calorimetry. The effects of macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP were reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 532–538, 2004     

Adsorption of Cr(VI) ions onto poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole)

Poly(ethylene glycol dimethacrylate‐1‐vinyl‐1,2,4‐triazole) [poly(EGDMA‐VTAZ)] beads (average diameter = 150–200 μm) were prepared by copolymerizing ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). Poly(EGDMA‐VTAZ) beads were characterized by swelling studies and scanning electron microscope (SEM). The adsorption of Cr(VI) from solutions was carried at different contact times, Cr(VI) concentrations, pH, and temperatures. High adsorption rates were achieved in about 240 min. The amount of Cr(VI) adsorbed increased with increasing concentration and decreasing pH and temperature. The intraparticle diffusion rate constants at various temperatures were calculated. Adsorption isotherms of Cr(VI) onto poly(EGDMA‐VTAZ) have been determined and correlated with common isotherm equations such as Langmuir and Freundlich isotherm models. The Langmuir isotherm model appeared to fit the isotherm data better than the Freundlich isotherm model. The pseudo first‐order kinetic model was used to describe the kinetic data. The study of temperature effect was quantified by calculating various thermodynamic parameters such as Gibbs free energy, enthalpy, and entropy changes. The dimensionless separation factor (R_L) showed that the adsorption of metal ions onto poly(EGDMA‐VTAZ) was favorable. It was seen that values of distribution coefficient (K_D) decreasing with Cr(VI) concentration in solution at equilibrium (C_e) indicated that the occupation of activate surface sites of adsorbent increased with Cr(VI). © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Temperature‐sensitive poly(N‐tert‐butylacrylamide‐co‐acrylamide) hydrogels bonded on cotton fabrics by coating technique

Different from the conventional method of developing stimuli‐sensitive textiles by graft copolymerization of environmental responsive polymers onto the fabric, the coating technique was applied to bond temperature‐sensitive hydrogels with cotton fabric through chemical covalent in our work. A temperature‐sensitive linear copolymer of N‐tert‐butylacrylamide (NTBA) and acrylamide (AAm) was prepared in methanol. Then, the cotton fabrics were coated using an aqueous solution of this copolymer containing 1,2,3,4‐butanetertracarboxylic acid as a crosslinker and sodium hypophosphite (SHP) as a catalyst, followed by drying and curing. The surface of the cotton fabrics was bonded on more or less coatings of poly (NTBA‐co‐AAm) hydrogels, as verified by Fourier transform infrared spectroscopy and scanning electron microscopy images. The poly(NTBA‐co‐AAm) hydrogels‐coated fabrics exhibited temperature sensitive, and the temperature interval of the deswelling transition was higher than lower critical solution temperature of linear copolymer solution. The coated fabrics presented good water‐impermeable ability because of the swelling of hydrogels bonded, especially when the add‐on was as high as 14.14%. Environmental scanning electron microscopy images revealed that coating hydrogels swelled and covered on the surface as a barrier to prevent water from penetrating once the coated fabric came into contact with water. The findings demonstrate that the temperature‐sensitive hydrogels can be covalently bonded on the cotton fabrics by coating technique and the coated fabrics have potential on immersion fabrics. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Phase Transformation and Rheological Behaviour of Highly Paraffinic “Waxy” Mixtures

An experimental investigation was undertaken for the rheology and phase transformation of prepared solutions comprising a paraffin wax dissolved in n‐dodecane or n‐hexadecane. The liquid‐solid phase transformation in wax‐solvent mixtures was investigated through the measurement of wax appearance/disappearance temperature (using cross polar microscopy, differential scanning calorimetry, viscometry and a visual method), pour point temperature and crystallization temperature. The results were utilized to prepare a temperature‐composition phase diagram for the wax+n‐C₁₆H₃₄ pseudo‐binary system. The effects of composition, temperature, cooling rate and shear rate were studied on the rheology of wax‐solvent mixtures. A correlation was developed for the apparent viscosity of wax‐solvent mixtures.