与强者同场竞技 靠创新促进发展——访青岛福润德塑料挤出技术有限公司总经理赵炳仁先生

一年一届的中国国际塑料橡胶工业展览会(国际橡塑展),是全球多个行业寻找橡塑工业世界性商贸伙伴的机遇,也是企业开拓中国以至亚洲市场商机之"金钥匙"。在25届国     

Hydrogels reinforced with nanoclays with improved response rate

Two series of semiinterpenetrating networks (SIPN) based on linear hydrophilic poly(vinyl alcohol) (PVA) and thermo‐responsive poly(N‐isopropylacrylamide) (PNIPA), physically crosslinked with inorganic clay, are presented. The hydrogels with different crosslinking densities were prepared by varying the content of clay from 1 to 6 wt % and contained linear interpenetrant, PVA in the range of 0.5–1.5 wt %. The effect of clay content on swelling/deswelling behavior and phase transition in PNIPA gels, as well as the feasibility of reinforcing the gels with high molecular weight PVA, were analyzed. The thermal response of hydrogels, followed by DSC, confirmed that the insertion of hydrophilic PVA did not have a significant effect on the onset of the volume phase transition temperature, while the response was faster. The equilibrium degree of swelling of SIPNs and PNIPA hydrogels was in the range of 9–79 and decreased with increasing content of clay. The internal morphology and surface wettability of the hydrogels were investigated by scanning electron microscope analysis and contact angle measurements, respectively. The network structural parameters of the PNIPA and SIPN nanocomposites hydrogels, such as the average molecular weight between crosslinks, M_c, and effective crosslinking density, N_e, were determined by dynamic mechanical analysis. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44535.     

Electrodialysis with brine solutions oversaturated with calcium sulfate

Electrodialysis (ED) was applied to concentrate brine solutions of various concentrations — similar to effluentsfrom the desalination of brackish and industrial water — to about 20%. The consequent reduction in effluent volumes would facilitate a reduction in disposal costs. The energy requirement for concentrating solutions from 70 to 300 mN (0.4-1.8%) to 3.9 N (20%) was in the range 1.5-7.1 kWh/m³, in contrast to approximately 25 kWh/m³ by thermal evaporation. With the aim of preventing precipitation of CaSO4 on the membranes, laboratory-scale ED experiments were carried out on solutions of different compositions to determine the conditions that would lead to the precipitation of excess gypsum on gypsum seeds in a separate precipitator. The results were then applied in a pilot-scale ED unit in which the brine that circulated through the ED brine cells passed through a separate CaSO, precipitator containing gypsum seeds.     

Biological studies with cyclopropenoids inactivated with fatty acids

Cyclopropenoids inactivated by reactingSterculia foetida oil with cottonseed oil fatty acids were fed at three dietary levels to growing rats and laying hens for 4 weeks. At the termination of the experiments, all animals were autopsied and examined microscopically for pathological lesions, but no pathology that could be related to dietary treatment was observed. Hemoglobin, packed cell volume and plasma cholesterol were similar in animals fed all of the diets. Growth rate of rats and egg production of hens fed the experimental diets were similar to those of animals fed the control diet. After 3 and 6 months of storage, eggs from hens fed the inactivated cyclopropenoids were normal and showed no evidence of the unusual characteristics of cyclopropenoid feeding. Lipids of heart, liver and adipose tissues of all the rats and hens varied little from the normal fatty acid composition. Small amounts of three unidentified fatty acids were found in the adipose tissues of rats fed the higher levels of inactivated cyclopropenoids. The results of these feeding studies suggest that inactivation of cyclopropenoids with fatty acids eliminates the unusual biological effects attributable to cyclopropenoids. Presented at the AOCS Meeting, New Orleans, April 1970.     

高压电动机受潮现场处理的技术分析

山东铝业公司水泥厂（以下简称我厂）运行的大型高压电动机较多．有时由于长时间停运或者环境的潮湿，导致电动机的绝缘水平下降，致使电动机不能再次正常启动。因大型电动机是企业的关键设备，其运行好坏直接影响企业生产的正常与否，进而影响企业效益。     

以创新谋发展 以协作促转型

复合肥行业的转型升级已被列为化肥行业"十三五"规划重要内容。介绍我国复合肥行业转型发展期的特征,并提出在此形势下复合肥行业的发展思路;以创新谋发展,促进行业技术水平提高;以协作促转型,助推行业转型发展。     

以创新铸就名牌 以名牌促进发展

介绍厦门正新橡胶工业有限公司在观念、产品、管理和技术方面开展创新活动的经验。观念创新是名牌战略的灵魂,相互理解与支持、创建伙伴关系是公司对外往来的原则,坚决实施名牌战略,坚持以人为本、适才适用的原则;产品创新是占领市场的法宝,根据市场需求不断适时开发新产品;管理创新是维护品牌形象的前提,各项试验均执行企业内控标准,严把产品质量关;技术创新是实施名牌战略的源泉,以自有技术开发各种轮胎。通过开展创新活动,公司利税指标一直位居国内前列。     

PPH治疗混合痔的护理体会

目的探讨混合痔行PPH的护理方法。方法99例混合痔患者均行PPH,手术前向患者介绍住院环境、住院须知,告知治疗方法及护理上需要的配合,饮食、排便的注意事项,术前准备等;术后体位及恢复饮食时间,大小便情况观察及各种外用药的使用,出血护理及伤口护理,肛门功能锻炼;制定入院评估,印制出院指导。结果99例患者痔核明显回缩,顺利出院。结论混合痔PPH的术前术后护理对患者顺利康复有重要意义。     

宝塔山:诚信赢天下,创新求发展——解读陕西宝塔山油漆股份有限公司

位于西部大开发的龙头省份——陕西省的陕西宝塔山油漆股份有限公司,自1958年创建以来,历经40多年的积累,40多年的发展,现已成为西北地区产销量最大的涂料生产企业和中国涂料工业骨干企业,以非凡的努力奠定了西北涂料业旗舰的地位。其资本结构的调整、诚信经营的建设及创新发展的模式,对涂料行业的发展可带来一些启迪借鉴。     

Fabric impregnated with TiO2 gel with self-cleaning property

Cotton fabric decorated with TiO₂ synthesized by sol-gel approach was investigated as a self-cleaning material depending on the TiO₂ loading (1.5 wt% in the case of single layered fabric and 3 wt% in the case of double layered). The materials were investigated by SEM, EDX, XRD, FTIR, and photoactivity. The self-cleaning property was established by determining the amount of the coated dust, the elemental composition, the carbon content, the opacity, and the water contact angle. The self-cleaning property of the impregnated fabric was accentuated by TiO₂ loading. The dust deposited on the single layer fabric stored inside was 3.8 wt% lower than on the nonimpregnated fabric and that deposited on double layer fabric, respectively, was reduced by 9.1 wt%. The decrease in the deposited dust was more accentuated for the samples stored outside (4.2 wt% for the single layer fabric and 16 wt% for the double layer fabric, as compared with the nonimpregnated textile).     

Crosslinking with malonate blocked isocyanates and with melamine resins

Automotive clearcoats with improved acid etch resistance are being formulated using a combination of a dialkyl malonate blocked polyisocyanate, a melamine crosslinker, and an acrylic polyol,^1,2 These coatings contain lower levels of melamine crosslinker compared to conventional acrylic/HMMM systems and show excellent acid etch resistance. We explored the reaction mechanism of this complex crosslinking system and found explanations for the good chemical resistance properties. Presented at the 25th International Waterborne, High-Solids, and Powder Coatings Symposium, February 18–20, 1998, New Orleans, LA. Science Rd., Norwalk, CT 06852; E-mail: AlexHe@Kingindustries.com and Wblank@Kingindustries.com.     

Crosslinking of styrene-butadiene rubber with polyurethanes bicapped with benzyocyclobutene

Summary A polyurethane prepared from 1,9-nonanediol and toluene-2,4-diisocyanate with M_n=11,840, was capped on both ends in a reaction with 4-(benzocyclobutenyl) methanol. The polyurethane was used to crosslink styrene-butadiene rubber through Diels-Alder reactions on the benzocyclobutene functionality. The synthesis and characterization of 4-(benzocyclobutenyl) methanol, a molecule not reported previously, is presented. The crosslinking reaction was carried out on intimate mixtures of the telechelic polyurethane and SBR at elevated temperature and pressure. Various physical properties of the crosslinked material were studied.Work done at the Department of Chemistry, University of Akron, Akron, OH 44325, USA     

Boundary-Layer Structure with Hydrogen Combustion with Different Injection Intensities

Results of numerical simulation of the influence of intensity of hydrogen injection through a porous surface in the case of hydrogen burning in the boundary layer are presented. Turbulent characteristics of the flow were simulated using the k–epsiv; turbulence model with Chien's modification for low Reynolds numbers. The diffusion model (infinitely large burning rate) was used to describe the chemical reaction process, but the difference in diffusion coefficients of different substances was taken into account. A comparison of injection with and without combustion shows that the presence of a heat-release front delays the laminar–turbulent transition and significantly deforms the profiles of density and viscosity of the gas mixture. As the injection velocity increases, the flame front is shifted from the porous surface toward the outer edge of the boundary layer. The contributions of injection itself and combustion to reduction of skin friction are analyzed. Key wrds: boundary layer, combustion, porous injection, heat and mass transfer, friction.     

纤维素酶协同作用蛋白质的研究进展

纤维素酶是木质纤维素原料降解的关键成本因素,综述了近年发现的一些与纤维素酶具有协同作用的蛋白质,及这些蛋白质的基本性质及协同作用的可能机理,以期望降低工业转化过程中纤维素酶的使用成本,并展望了木质纤维素制取燃料乙醇的发展前景。     

OMC法煤气脱硫装置的操作经验

讨论了在ＯＭＣ法煤气脱硫工艺中,贫液碱度、贫液中盐类含量、脱硫剂ＯＭＣ浓度和ＯＭＣ质量等因素对煤气脱硫效率的影响,指出了提高脱硫效率的途径和降低消耗的经验。     

Azo-polymers modified with nucleobases and their interactions with DNA molecules

The photo-fluidization process which is specific for azo-materials opens a new perspective for their use in the field of molecules nano manipulation at the surface of the azo polymer films. This is possible considering that in the case of the UV irradiation from a polarized laser source the azo material has an unidirectional flow. Here, we investigated the structuring phenomena occurring on the surface of the azo-polysiloxanes films modified with nucleobases, upon UV irradiation. Measurements of topography and adhesive forces between polymeric substrates and a hydrophilic probe have been done by atomic force microscopy (AFM). The response of the material upon irradiation has been investigated also by using UV−VIS spectroscopy. This method allowed us to draw the photo-isomerization and relaxation curves. Also, preliminary tests were conducted to determine the capacity of the film surface to immobilize DNA molecules.     

Copolymerization of acrylonitrile with maleamic acid derivatives and with carboxyphenylmaleimide

Acrylonitrile was copolymerized with two N-arylmaleamic acids and with N-3-carboxyphenylmaleimide in dimethylformamide (DMF) using azobisisobutyronitrile as initiator. The reactivity ratios and the Q-e parameters of these monomers were estimated, and the resulting copolymers were characterized by viscosity measurements and thermal analysis. Thermogravimetry and differential thermal analysis data showed an improvement in the thermal behaviour of the investigated copolymers compared with that of poly(acrylonitrile). Mechanisms illustrating the role of both the acidic group and the maleimide ring in the nitrile oligomerization were proposed. The produced copolymers showed an excellent affinity towards basic dyes and better color fastness towards UV light.     

Experience with a glass-melting furnace with a developed working front

Glass and Ceramics -     

Dehydrochlorination of propylene chlorohydrin with sodium hydroxide and with catholyte

Dehydrochlorination of an aqueous solution of propylene chlorohydrin with sodium hydroxide (12·5 and 30% by weight), with catholyte (5 or 10% by weight NaOH + 14% by weight NaCl) and with milk of lime (15% by weight) were compared. The use of catholyte (10% by weight NaOH + 14% by weight NaCl) enables propylene oxide to be obtained in a yield of 94·3%, with 100% conversion of chlorohydrin. The concentration of 1,2-propylene glycol in the waste is 0·07% by weight.     

122例酒精性肝病患者的临床研究

目的探讨酒精性肝病患者的治疗方法与临床疗效。方法回顾性分析我院收治的122例酒精性肝病患者的临床资料,所有患者随机分为2组,实验组61例患者在常规治疗的基础上采用阿托莫兰联合易善复进行治疗,对照组61例患者采用常规治疗的方法进行治疗。治疗结束后观察2组的临床疗效。结果实验组的疗效明显高于对照组,2组差异有统计学意义(P<0.05)。结论阿托莫兰联合易善复治疗酒精性肝病疗效肯定,能明显改善酒精性肝病患者的临床症状,并促进黄疸的消退,促进肝功能恢复。