Solution assisted laser ablation synthesis of discrete aluminum nanoparticles

Discrete aluminum nanoparticles with an average particle size of 21 nm have been prepared by laser ablation of a metallic aluminum target submerged in dry tetrahydrofuran in the presence of 0.001 M oleic acid as a stabilizing ligand. The particles display high solubility and minimal aggregation while the absence of oleic acid leads to highly aggregated particles and a broader particle size distribution. O/Al ratios obtained from EDS analysis suggest that the particles produced are primarily metallic aluminum with minimal oxide content.     

Metal nanoparticles generated by laser ablation

We study a new method for producing ultrafine metal particles (nanopartides) that employs Laser Ablation of Microparticles (LAM). Pulsed excimer laser radiation at 248 nm wavelength was used to ablate ~2 μm feedstock of silver, gold, andpermalloy (Ni₈₁%:Fe_19%) under both normal atmospheric conditions and in other gases and pressures. A model for nanoparticle formation by LAM is proposed that includes plasma breakdown and shock-wave propagation through the initial microparticle. Behind the shock a large fraction of the original microparticle mass is converted to nanoparticles that diffuse to silicon substrates and TEM grids for collection and analysis. Nanoparticle morphologies are spherical except for gold nanoparticles >100 nm that are generally cubes. Electron micrographs of the samples were analyzed by computer-aided image processing to determine the effect of irradiation conditions on the nanoparticle size distribution. The results showed that mean particle diameters were normally in the range from 10 to 100 nm and that the particle size distributions were generally log-normal, with dispersion (diameter/standard deviation) ranging from 0.2 to 0.5. For metallic microparticle feedstock, the mean size of the produced nanoparticles generally increased with increasing laser fluence and were smallest for fluences not too far above the breakdown threshold.     

Zinc nanoparticles in solution by laser ablation technique

Colloidal zinc metallic nanoparticles are synthesized using pulsed laser ablation of metal plate in an aqueous solution of suitable surfactant to prevent aggregation. UV-visible absorption, TEM, small angle X-ray diffraction and wide-angle X-ray diffraction are used for the characterization of colloidal zinc metallic nanoparticles. Colloidal nanoparticles are found highly stable for a long time.     

Percolation in laser ablation of binary mixtures

We have studied the optical emission of plasma expanding from a target made of a binary alloy or a pressed powder mixture and ablated by nanosecond laser pulses of moderate power. The intensity of spectral lines has been studied for the first time as dependent on the target composition. It is established that a three-dimensional percolation takes place in the plasma, with a percolation threshold determined by the atomic density of a metal component in the target composition.     

X-ray diffraction of permalloy nanoparticles fabricated by laser ablation in water

Permalloy (NiFeMo) nanoparticles were fabricated by laser ablation of bulk material in water with a UV pulsed laser. Transmission electron microscope images showed that approximately spherical particles about 50 nm in diameter were formed in the ablation process. All diffraction peaks corresponding to the bulk material were present in the nanoparticles. In addition to these peaks several new peaks were observed in the nanoparticles, which were attributed to nickel oxide.     

Optimisation of GaAs nanocrystals synthesis by laser ablation in water

Laser ablation of a gallium arsenide (GaAs) wafer immersed in distilled water was carried out using the fundamental wavelength of a high frequency Nd:YAG laser with 240?ns pulse duration. Rate of nanoparticles generation through laser ablation for various amounts of laser pulse energies (0.4–0.94?mJ) and repetition rates (400–2000?Hz) were studied and a maximum ablation rate of 19.6?µgr/s was obtained. Formation of the pure GaAs nanocrystals (NCs) is confirmed using TEM micrograph and X-ray diffraction analysis. Band-gap energy of generated GaAs NCs is calculated by Tauc method to be between 2.48 and 2.60?eV which is larger than the band-gap energy of bulk GaAs. The band-gap energy of NCs is increased by increasing the energy of laser pulses and is decreased by increasing the pulse repetition rate.     

Non-equilibrium synthesis of Fe-Cr-C-W alloy by laser cladding

Synthesis of Fe-Cr-C-W alloy using the laser cladding technique offered an opportunity to produce a novel wear-resistant material with fine and uniform microstructure. Use of preheating during laser cladding Fe-Cr-C-W provided crack-free clads. The preheating temperature was very critical to eliminate cracks in the clad. Different complex types of carbide were observed in this research. Overall laser process parameters such as power density or specific energy as well as preheating temperature affected the characteristics of the carbide precipitates in the matrix. The increase of solid solubility and high cooling rate resulted in good metallurgical characteristics. Mostly M₆C or M₂₃C₆ type carbides were observed. Usually diamond-shaped M₆C carbides showed good tribological characteristics. In general, increasing the power density brought an increase of average hardness, while decreasing the power density brought a decrease of wear scar width. The laser-clad Fe-Cr-C-W alloy showed better wear properties than laser-clad Fe-Cr-Mn-C and several times smaller scar width as compared to Stellite 6 hard-facing during line-contact wear testing.     

Synthesis and optical characterization of copper nanoparticles prepared by laser ablation

The remarkable size-tunable properties of nanoparticles (NPs) make them a hot research topic with applications in a wide range of fields. Hence, copper (Cu) colloidal NPs were prepared using laser ablation (Nd:YAG, 1064 nm, 7 ns, 10 Hz, 6000 pulses) of a copper metal plate at different laser fluences (LFs) in the range of 1–2.5 J cm^?2 in ethylene glycol (EG), at room temperature. Analysis of NPs was carried using different independent techniques such as ultraviolet–visible (UV–vis) spectroscopy; transmission electron microscopy (TEM) and Fourier transform infrared (FTIR) spectroscopy. TEM analysis showed that the NPs were spherical with a bimodal distribution and an average particle size of 5 and 16 nm influence of 1.2 J cms^?2, and 9 and 22 nm at 2 J cm^?2. The UV–vis spectra of colloidal NPs revealed the maximum absorbance at around 584 nm, indicating the formation of Cu NPs, which supported using FTIR spectra. Furthermore, the absorption spectra confirmed the metallic nature of Cu NPs. FTIR spectroscopy was utilized to verify information about the NPs surface state and chemical bonds constructed in the atom groups apparent on their surface.     

Stoichiometry of alloy nanoparticles from laser ablation of PtIr in acetone and their electrophoretic deposition on PtIr electrodes

Charged Pt-Ir alloy nanoparticles are generated through femtosecond laser ablation of a Pt?Ir target in acetone without using chemical precursors or stabilizing agents. Preservation of the target's stoichiometry in the colloidal nanoparticles is confirmed by transmission electron microscopy (TEM)-energy-dispersive x-ray spectroscopy (EDX), high angle annular dark field (HAADF) scanning transmission electron microscopy (STEM)-EDX elemental maps, high resolution TEM and selected area electron diffraction (SAED) measurements. Results are discussed with reference to thermophysical properties and the phase diagram. The nanoparticles show a lognormal size distribution with a mean Feret particle size of 26 nm. The zeta potential of -45 mV indicates high stability of the colloid with a hydrodynamic diameter of 63 nm. The charge of the particles enables electrophoretic deposition of nanoparticles, creating nanoscale roughness on three-dimensional PtIr neural electrodes within a minute. In contrast to coating with Pt or Ir oxides, this method allows modification of the surface roughness without changing the chemical composition of PtIr.     

Fabrication of Ta nanoparticles induced by nanosecond laser ablation in ethanol: the study of laser fluence effects

Tantalum nanoparticles (Ta NPs) were synthesized in ethanol solution by ablation with a 1064 nm Nd:YAG laser. Prepared NPs were investigated by UV-visible absorption spectroscopy, Transmission electron microscopy, X-ray diffraction and Photoluminescence measurement. The average sizes of NPs were calculated to be in the range of 12–18 nm. From the UV-visible studies, the plasmon peak position of Ta NPs was observed in the spectral range of 206–208 nm. The XRD spectra clearly showed the crystalline structure of NPs and various peaks of Ta and Ta₂O₅. Moreover, the UV region in the PL spectrum included the free exciton and the bound exciton emission correlated with the defect concentration. In fact, the laser ablation in the organic and inorganic solvents is a strong technique to obtain some NPs with particular structures, which are impossible to produce by conventional methods.     

Synthesis of ceramic nanoparticles by ultrafast laser ablation of solid targets in water

We report production of nanoparticles of several advanced ceramics (Si3N4, SiC, AlN, and Al2O3) by ablation with femtosecond laser pulses of solid targets submerged in deionized water. The products withstand comparison with commercial nanoparticle suspensions obtained by other techniques as they are analyzed by means of transmission electron microscopy. As compared with metal nanoparticles produced with the same technique, we have found that the overall dependence of mean sizes and distribution widths on the laser fluence is similar. We explain why it is difficult to synthetize very small (<5 nm) and monodisperse particles in terms of ablation mechanism and discuss the aplicability of the technique for industrial production.     

Effect of temperature on the characteristics of ZnO nanoparticles produced by laser ablation in water

Effect of the water temperature on the characteristics of zinc oxide nanoparticles (NPs) produced by laser ablation process is investigated experimentally. The fundamental wavelength of a Q-switched Nd:YAG laser was employed to irradiate a high-purity zinc plate in distilled water at different temperatures of 0, 20, 40 and 60^°C. The produced NPs were diagnosed by UV–vis–NIR spectroscopy, X-ray diffraction method, transmission electron microscopy and scanning electron microscopy. Results show that with increase in the water temperature from 20 to 60^°C, size of NPs decreases while their bandgap energy increases. Maximum ablation rate occurs at the highest temperature. Crystalinity also increases with increase in the water temperature. The abnormal behaviour of water at 0–4^°C affects the NPs characteristics.     

Synthesis of ultra-small silicon nanoparticles by femtosecond laser ablation of porous silicon

We report a detailed study on the synthesis of ultra-small (1–10 nm) colloidal silicon nanoparticles (Si NPs) by ablating porous silicon (pSi) in acetone using femtosecond laser pulses. Porous silicon is considered as a target material for ablation because it contains a large number of light emitting silicon nanoparticles. The pSi samples were prepared by anodic etching of silicon in aqueous HF solution for different etching current densities. Transmission electron microscope measurements confirmed the successful formation of well-isolated spherical silicon nanoparticles. The average size of spherical NPs were estimated to be ~7.6, ~7, and ~6 nm when anodic etching current densities of 5, 10, and 20 mA/cm² were used respectively for preparing pSi targets. The crystallinity of these Si NPs was confirmed by selective area electron diffraction and Raman spectroscopy measurements. The observed blue shift in the absorption and emission spectra are attributed to reduction in the average particle size with increase in etching current density. These Si NPs may be useful for fabricating low-dimensional microelectronic compatible photonic devices.     

Tribological properties of polymer nanohybrids containing gold nanoparticles obtained by laser ablation

We have studied polystyrene (PS)+Au particles nanohybrids. Approximately spherical gold nanoparticles with the average diameter of 15 nm were obtained by laser ablation in a liquid environment. Thus any chemical residue on the particles was eliminated. Focused ion beam (FIB) milling plus scanning electron microscopy (SEM) observation show that Au particles are fairly well dispersed inside the polymer matrix, better than when PS is simply dissolved in a nanoparticle solution. The Au particles concentration as low as 0.15 wt% results in dramatic changes in tribological properties, namely dynamic friction and pin-on-disk wear. Both wear and dynamic friction results are explained in terms of high brittleness of PS, abrasion of Au particles against a ceramic indenter, and also effects of density of filler particles in the matrix on tribological properties. Effects of varying normal load on friction are small.     

Studies on optical limiting characteristics of silicon nanoparticles synthesized by laser ablation

We present synthesis of silicon nanoparticles dispersed in toluene by laser ablation and studies on their optical limiting properties with nanosecond laser pulses at 532 nm. Silicon nanoparticles in toluene show better optical limiting compared to standard optical limiter fullerene C60 in toluene. Optical limiting threshold of silicon nanoparticles is about three times less than that of C60. Detailed studies using Z-scan experiments, angle dependent scattering, intensity dependent transmission and temporal profile measurements indicate that apart from non-linear scattering, nonlinear absorption and nonlinear refraction also contribute to the optical limiting behavior of silicon nanoparticles.     

纳米颗粒的短脉冲激光烧蚀制备及其非线性光学应用

本文主要介绍了纳米颗粒的短脉冲激光制备及其在非线性光学领域的应用。短脉冲激光制备纳米颗粒具有纯度高、操作简单和适用性广等优点,所制备的非线性纳米颗粒尺寸分布均匀,粒度小且可调控,在非线性光学材料中有着独特的地位。为了更深入地对此进行研究,本文介绍了纳米颗粒的光学非线性和激光的特点和原理。在此基础上,通过阐述短脉冲激光与物质相互作用的机理,说明了激光制备纳米颗粒所具有的优点,详细分析了制备条件对合成纳米颗粒的影响,并结合激光制备不同的纳米颗粒,介绍当前激光制备各类纳米颗粒的研究现状。激光制备纳米颗粒是一种操作简便、适用性广,且对环境友好的方法。

     

Preparation of colloidal cadmium selenide nanoparticles by pulsed laser ablation in methanol and toluene

Colloidal spherical nanoparticles (NPs) of cadmium selenide (CdSe) have been prepared by laser ablation of cadmium target in methanol and toluene solutions. The properties of CdSe nanoparticles ablated in methanol and toluene were investigated and compared. The morphology and structure of synthesised CdSe NPs were analyzed by X-ray diffraction (XRD), scanning electron microscopy and transmission electron microscope (TEM). XRD investigation revealed that the nanoparticles are crystalline and have hexagonal structure. Optical absorption showed that the value of optical energy gap of ablated CdSe nanoparticles depends on the solution type. TEM measurements showed that CdSe NPs with diameters ranging from 25 to 35 nm were synthesised in methanol while, the nanoparticles ablated in toluene have diameters in the range of (40–50) nm.     

Optical and structural characteristics of silicon nanoparticles thin film prepared by laser ablation

In this paper thin film of silicon nanoparticles on glass substrates have been prepared by dip-coating method using colloidal silicon nanoparticles generated by nanosecond laser ablation of silicon wafer in ethanol. The resulting nanoparticles and structural properties and morphology of thin film were characterized by UV-Visible absorption spectrometry, transmission electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction pattern and atomic force microscopy image. Nanoparticles with diameters ~ 9 nm were observed to be formed in the colloidal solution. The atomic force microscopy image of Si nanoparticles thin film shows that the overall average width is about 80 nm.