The caloric effects under combined applications of magnetic field and hydrostatic pressure to a MnCoSi meta-magnet were investigated. Under a magnetic field change of 0–5 T, the maximum magnetic entropy change was enhanced by 35.7% when a 3.2kbar hydrostatic pressure was applied, and the cooling temperature span was extended by 60 K when a hydrostatic pressure of 9.7 kbar was applied. The coupled caloric entropy change, which originates from the coupling between the magnetism and volume, was calculated and accounted for the enhanced entropy change of MnCoSi. The present work facilitates the use of MnCoSi as a solid-state refrigerant and also enriches the investigation of the multicaloric effect under multiple external fields.
Graphical abstractOrganic/inorganic thermoelectric composites have played an important role in the development of new, green, and renewable energy sources with potential applications in efficient thermal management, flexible electronics, and bioelectronics. Electrochemical syntheses, including electropolymerization, electrochemical deposition, electrochemical doping, electrochemical post-processing, etc., require no addition of surfactants or oxidants, the products of which are easy to separate and purify, providing clean, efficient, and facile routes for the preparation of organic thermoelectric materials and their composites. In this review, the preparation, properties, and applications of organic/inorganic thermoelectric composites from electrochemical synthesis were reviewed in detail, offering a perspective on the recent advances in the field.
Graphical abstractIn this critical note, the thermal stability behavior of ultra-fine grained (UFG) and nano-structured (NS) metals and alloys produced through severe plastic deformation (SPD) techniques is reviewed. For this case, the common engineering metals with body-centered cubic (BCC), face-centered cubic (FCC), and hexagonal close-packed (HCP) crystal structures such as aluminum, copper, nickel, magnesium, steel, titanium, and their relating alloys were assessed. Microstructural evolution in these severely deformed materials following post-processing annealing treatment was investigated for various times and temperatures below the recrystallization point. The microstructure development reported in the literature was studied in terms of the stable grain structures correlated with different levels of plastic straining. The stacking fault energy (SFE) is noted to be a key issue which has a critical influence in predicting the coalescence or coarsening behavior of ultra-fine and nanoscale grains after SPD treatment by controlling the cross-slip phenomenon for screw dislocations.
Graphical AbstractCrop harvester machines have played a significant role in increasing crop yield by harvesting at the optimal time and reducing crop losses; however, the main issue is the wear and corrosion of the cutting knives, so the goal of this work is to promote the mechanical and chemical knife surfaces. The blank knife was made of low carbon steel. To achieve the goal of this work, Ni-TiO2 nanocomposite-coated steel was created using electrodeposition technology from Watt's nickel bath with various current densities in the range of (1–4 Adm?2) and TiO2 nanoparticles concentration in the range of (0–1 gL?1). Mechanical and chemical tests were performed on the blank, pure Ni, and Ni-TiO2 nanocomposites. The corrosion property of the investigated samples was carried out in 3.5 wt. % NaCl solution at room temperature. The outcomes of the study showed a co-deposition of TiO2 nanoparticles within the Ni matrix to produce nanocomposites-coated steel, and that formed at 3 Adm?2 and with added 0.5 g/L TiO2 nanoparticles has a major impact on improving the corrosion resistance and mechanical properties such as abrasion resistance, hardness, young's modulus, plastic, and elastic parameter, as well as fretting test.
Graphical abstractIn view of the disadvantages of concentration polarization and trade-off effects in the application of membrane in desalination field, oxide-nano graphene oxide/polyamide (O-NGO/PA) loose intermediate layer and PA ultra-thin dense layer were introduced to fabricate PA/O-NGO/polyphenylene sulfide composite membrane with sandwich structure via multi-step interfacial polymerization (MS-IP) method. The selective permeation mechanism of ultrathin layer produced by different aqueous monomers (PIP and MPD) was studied, the effect of its physicochemical structure on the relief of concentration polarization phenomenon and the breakthrough of trade-off effect was analyzed. The ultra-thin and dense PA layer mainly played the role of interception and shortened the water molecular penetration path. In the retention test of metal salt solution, compared with the rough surface, it was found that the smooth surface was more conducive to the diffusion of intercepted metal ions into the feed solution, thus alleviating the concentration polarization phenomenon.
Graphical abstractCarbon nanomaterials have shown great potential as electric heating elements in electrothermal applications. However, carbon-based heating elements with high flexibility, ultrafast electrothermal response, low driving voltage, high heating temperature, and stretchability are still lacking. Here, continuous electrospun carbon nanofiber films (CNFFs) and corresponding composite films additionally containing silicone (CSCFs) as electric heating elements are proposed. CNFFs were prepared by electrospinning and subsequent heat treatment, and CSCFs were prepared by composing CNFFs with silicone via hot-pressing procedure. Both of them have shown excellent performance as electrothermal films, such as ultrafast electrothermal response, high resistance adjustability, high flexibility, high operation stability, and high infrared emissivity. In particular, a temperature as high as 200 °C can be reached within 2 s at 8 V. Suitable robustness and flexibility allow CSCFs to bear various deformations, such as bending, twisting, folding, and even stretching by a factor of 1.3, without worsening electrothermal performance. Also, excellent water resistance has been confirmed. The superior electrothermal performance is mainly attributed to the high electrical conductivity, continuous fiber structure, high specific surface area, and adjustability of nanofiber stacking density and thickness of CNFFs.
Graphical abstractIn this study, poly(L-lactic acid) (PLA)/low molar mass alkali lignin (aL) (1%, 5% and 10% w/w) composites were prepared primarily for a comprehensive understanding of the effect of aL on their antimicrobial properties, biocompatibility and cytotoxic behavior. The properties were evaluated by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, thermogravimetry and X-ray diffraction. The mechanical, water vapor barrier properties and photodegradability were analyzed as well. The results showed a significant inhibiting effect of aL on the crystallization behavior of PLA, increased water barrier properties (up to 73%) and photodegradability. PLA/aL composites showed a tenfold reduction in Gram-positive bacteria viability, very good cellular response and very low cytotoxicity levels, thus validating these materials as non-cytotoxic and with high potential to be used as food packaging.
Graphical abstractSustainable betalain pigments extracted from beetroots were used as eco-friendly film coating over aluminium surface. The film coating was examined and verified by corrosive 1.0 M HCl solution. Characterization of chemical structure of the betalain pigments was done using spectroscopic attenuated total reflectance Fourier transform infrared (ATR-FTIR) and UV–Vis technique. Scanning electron microscope technique was used to demonstrate the eco-friendly film coating before and after been examined via corrosive 1.0 M HCl solution. Various operating conditions were studied to meet highest inhibition efficiency values such as betalain concentration, operating temperature and turbulent flow, and maximum inhibition efficiency?=?98.4% was displayed. Multiple adsorption isotherms like Langmuir, Temkin, and Freundlich were used effectively to determine equilibrium constants and adsorption parameters. Dynamic investigations revealed a decline of rate of corrosion (RC) and rise of activation energy values (Ea) at higher betalain concentrations. Thermodynamic investigations revealed physisorption process, exothermic enthalpy, and low entropic values of betalain on aluminium surface. The noticeable specifications of low cost, abundance and sustainability, environmentally friendly, and high technical feasibility of betalain pigments adapt them to be the futuristic outstanding sustainable film coating for metal surfaces.
Graphical abstractPlanar perovskite solar cells (PSCs) have excellent photoelectric properties and show great commercialization potential. However, there are a lot of crystal defects in the perovskite films prepared by solution method, which reduces the development process of solar cells. In this work, alizarin red s (ARS) was doped into MAPbI3 films to passivate the defect. It was shown that the addition of ARS increased the quality of perovskite film and doped perovskite film exhibited improved light absorption. In addition, it was found that there was a strong interaction between ARS and perovskite, which reduced the density of defect states. The results showed that the passivated perovskite device had improved PL intensity, increased carrier lifetimes and reduced charge recombination. After passivation, the device obtained a higher open-circuit voltage (VOC) of 1.103 V where the control device was 1.055 V, and the best power conversion efficiency (PCE) of the doped device was 18.82%, which is 11.36% higher than that of the control device of 16.90%.
Graphical abstractThe kinetics of electrochemical corrosion of aluminum alloy (AlMg6) surfaces with different wettability was analyzed. The surfaces were processed by three different methods, in particular, polishing, laser texturing, the combination of laser texturing and low-temperature heating. After laser processing, the dimple-like texture was formed on the surface, and the wettability significantly enhanced. Low-temperature heating of laser-textured AlMg6 alloy surfaces led to the wettability inversion from strongly hydrophilicity to superhydrophobicity. Microscopic and profilometric methods were used to estimate the surface degradation due to corrosion when aggressive solution droplets (a mixture of NaCl and hydrogen peroxide aqueous solutions) evaporated. The potentiodynamic polarization measurements of AlMg6 alloy surfaces were conducted. The typical modes of corrosion and evaporation of aggressive solution droplets were detected. The kinetics of corrosion was estimated by the behavior of the corrosion area evolution. In addition, when immersing laser-textured sample with strongly hydrophilic properties into aggressive solution, the higher corrosion rate was found in the liquid meniscus region (aggressive mixture / alloy / air interface) compared to the textured site immersed in the mixture. This was explained by convection increasing the rate of reaction products removal and promoting a stronger deviation from the equilibrium state in the aggressive mixture. Experimental results of the potentiodynamic polarization measurements revealed that laser-textured samples exhibit enhanced corrosion protective properties compared to polished samples.
Graphical abstractThe development of eco-friendly connection material instead of steel is a challenging problem in timber structures. Following densification, the mechanical properties of low-density species can be significantly improved. Densified wood may be a potential connection material in timber structures. This paper reviewed the different processing for densified wood, and obtained favorable mechanical properties and dimensional stability based on small specimen sizes, which are much less than the applicable sizes in practice. A densification processing with alkali pretreatment was adopted for poplar widely cultivated in the world to produce the densified poplar, which has been rarely reported as connection material. Various specimens of densified poplar were tested to obtain their main mechanical properties such as strength and deformability. The set recovery of densified poplar was also measured to observe their dimensional stability. In addition, the hygroscopic swelling strains for the diameter of densified poplar dowel were measured to present their moisture-dependent behavior. The improved mechanical properties and dimensional stability confirmed the fact that densified poplar with alkali pretreatment can be an optimal connection material.
Graphical abstractThree-dimensional (3-D) printing, also known as additive manufacturing, refers to a method used to generate a physical object by joining materials in a layer-by-layer process from a three-dimensional virtual model. 3-D printing technology has been traditionally employed in rapid prototyping, engineering, and industrial design. More recently, new applications continue to emerge; this is because of its exceptional advantage and flexibility over the traditional manufacturing process. Unlike other conventional manufacturing methods, which are fundamentally subtractive, 3-D printing is additive and, therefore, produces less waste. This review comprehensively summarises the application of additive manufacturing technologies in chemistry, chemical synthesis, and catalysis with particular attention to the production of general laboratory hardware, analytical facilities, reaction devices, and catalytically active substances. It also focuses on new and upcoming applications such as digital chemical synthesis, automation, and robotics in a synthetic environment. While discussing the contribution of this research area in the last decade, the current, future, and economic opportunities of additive manufacturing in chemical research and material development were fully covered.
Graphical abstractApplication of phase change materials (PCMs)-based thermal management technology in flexible electronic devices has been inhibited due to the leakage and strong rigidity of PCMs. A novel flexible composite PCMs with ultrahigh extensibility was developed in this paper. Concretely, a kind of paraffin@copper (PA@Cu) microcapsule with paraffin as core and nano-Cu particle as “flexible” metal shell was prepared by a simple Pickering emulsion method in an aqueous medium. The encapsulation ratio of paraffin reached 98wt%. Then the PA@Cu microcapsules were introduced into uncured liquid silicone to fabricate flexible composite PCMs (PA@Cu/SE). SEM results demonstrated that the microcapsules were tightly and uniformly wrapped in the three-dimensional network structure of silicone elastomer matrix. Owing to the good compatibility of PA@Cu with the polymer elastomer and a barrier for the melted PA provided by the “flexible” nano-Cu shell, the resulting composite PCMs present superior flexibility and thermal reliability. Tensile tests showed that the flexible composites with a relative higher loading of PA@Cu (40wt%) exhibit outstandingly larger extensibility (>?730%) than many reported literatures. In addition, the composites presenting superior thermal protection for biological tissue make them well-suited for thermal management in wearable electronics.
Graphical abstractSilver nanowires find use in a myriad of applications, including communication systems, sensors, medical devices and electrical equipment. Temperature-dependent electrical and thermal properties of chemically derived silver nanowires are rarely explored. In the present work, seed-mediated synthesis of silver nanowires has been carried out, and their electrical and thermal conductivity at 300 K is found to be 1.848?×?107 S/m and 64.8 W/mK, respectively. A screen-printable ink of silver nanowires is formulated and printed on low-cost and widely used substrates like paper and cotton fabrics. Flexible printed electrodes could be made possible with uniform printed structures obtained in cotton fabric and paper substrate. The printed pattern exhibited sheet resistance of 0.7 Ω/sq. Screen-printed silver nanowires on paper show shielding efficiency of 99.9% in X band, which promotes them as excellent candidates in fabricating lightweight electronic devices by a one-step printing process.
Graphical abstractNanotechnologies known as a developing applied science have significant global socioeconomic values and many advantages obtained from nanoscale materials. Its applications can have significant effects on the performance of organizations. The advance of two-dimensional (2D) MXene-derived QDs (MQDs) is currently in the initial stages. Scholars have shown distinguished optical, electronic, thermal and mechanical attributes by surface chemistry and versatile transition metal. In this field of study, many applications are introduced like energy electromagnetic interference shielding, storage, sensors, transparent electrodes, photothermal therapy, catalysis and so on. The vast range of optical absorption attributes of MQDs along with high electronic conductivity has been detected to be key attributes because of their achievement in the mentioned usages. Currently, relatively little materials are highly known because of their basic electronic and optical properties, which can limit their full potentials. From a theoretical and experimental point of view, in this work, electronic and optical properties of MQDs along with applications corresponding to those properties were evaluated.
Graphical abstractAquivion membrane displays improved properties as compared to Nafion membrane, partly due to shorter side chains. However, some improvements are still necessary for proton exchange membrane fuel cell to operate at low relative humidity. To overcome this drawback, the addition of clay nanoparticle into the Aquivion matrix can be considered. In this study, different composite membranes have been prepared mixing short-side-chain PFSA (perfluorosulfonic acid) Aquivion and selectively modified halloysite nanotubes for PEMFC low relative humidity operation. Halloysites were grafted with fluorinated groups, sulfonated groups, or perfluoro-sulfonated groups on inner or outer surface of the tubes. The obtained composite membranes showed improved properties, especially higher water uptake associated with reduced swelling and better mechanical strength compared to pristine Aquivion membrane and commercially available Nafion HP used as reference. The best performance in this study was obtained with Aquivion loaded with 5 wt% of pretreated perfluoro-sulfonated halloysite. The composite membrane, referred to as Aq/pHNT-SF5, displayed the largest water uptake and proton conductivity among the panel of membranes tested. The chemical stability was not affected by the presence of halloysite in the Aquivion matrix.
Graphical abstractNon-dendritic microstructures are generally obtained in metals after semi-solid deformation (deformation during solidification); however, dendritic growth is preferred without deformation. The fragmentation of dendrites is recognized as an essential contributing factor to non-dendritic microstructures. However, the underlying mechanism of fragmentation needs to be clarified in depth. It is infamously hard for researchers to carry out a direct observation of this process. Moreover, a comprehensive numerical survey of this process is not trivial. The present research reported a new method to model dendritic growth during semi-solid deformation. The motion and deformation of the solid coupled with liquid flow in the melt were treated as the two-phase flow because plastic materials could be formulated as non-Newtonian fluids. The vector-valued phase-field formulation and the self-constructed Navier–Stokes solver made it possible to simulate the growth, motion, deformation, fragmentation and agglomeration of two dendrites coupled with liquid flow in the melt. Computational results suggest that fragmentation can occur when the grain boundary is wet and penetrated by the melt, giving new supporting evidence to a previously proposed mechanism for the fragmentation of dendrites.
Graphical abstractWe review the literature describing the use of interleaves to increase interlaminar fracture toughness in fibre-reinforced polymer composites and hence to improve damage tolerance. From an analysis of data provided in the literature from the use of microfibre and nanofibre interleaves, we show that the performance of these widely researched systems is clearly differentiated when plotted against the mean coverage of the interleaf. Using a simple analysis, we suggest that this can be attributed to the influence of their porous architectures on the infusion of resin. We show also that the superior toughening performance of microfibre interleaves is only weakly influenced by the choice of fibre. We find also that the inclusion of carbon nanotubes within interleaves to deliver multifunctional composites can be optimised by using a hybrid system with microfibres.
Graphical abstractHybrid organic–inorganic nanocomposites are great candidates for display and illumination systems due to improved optoelectronic properties and photostability. This work endeavours towards the scientific study of the influence of defect-induced zinc oxide nanoparticles (ZnO) on the optical characteristics of poly[2-methoxy-5-(2′-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV). ZnO nanoparticles consist of many vacancies which facilitate light emission across the visible region. The green defective emission occurring due to the presence of oxygen vacancies in ZnO was used to re-excite MEH-PPV and hence, improve the luminescence quantum efficiency. The photostability of the nanocomposite was enhanced through charge transfer (prevents the formation of superoxides) and energy transfer (reduces the non-radiative decay) mechanisms.
Graphical abstractPolyimide aerogels are promising for diverse applications owing to their nanoporous structure and superior performance in thermal insulation, dielectric protection, etc. However, the severe shrinkage they usually suffer has long been a threat, and can pose great challenges to their shape-stable preparation and reliable applications. It is very important to clarify the effects of various factors on the shrinkage of PI aerogels and the effective strategies available for shrinkage reduction. These are also the focuses of the present review, to provide guidance for preparing PI aerogels with greatly reduced shrinkage, and thereby improved shape stability and use reliability. Since the shrinkage of PI aerogels is quite a complex issue, further studies on PI aerogels against shrinkage deserve continuous attention.
Graphical abstract