Microstructure and properties of Al0.3CrFe1.5MnNi0.5Ti x and Al0.3CrFe1.5MnNi0.5Si x high-entropy alloys

In this article, the microstructure, hardness, and corrosion resistance of the Al0.3CrFe1.5MnNi0.5Tixand Al0.3CrFe1.5MnNi0.5Six(x = 0, 0.2, 0.5, 1.0) high-entropy alloys were investigated via X-ray diffraction(XRD)scanning electron microscopy(SEM), digital display Vickers hardness tester, and electrochemical technique These alloys are mainly composed of BCC solid-solution structure. When adding high content of Ti or Si elemen(x C 0.5), some intermetallic compounds are found in the microstructure, which makes the alloys have a high hardness, high brittleness, and easy cracking. While the alloys with low content of Ti or Si(x = 0.2) have a hardness of HV 420–HV 430, and its hardness increases about 14 %compared with that of Al0.3CrFe1.5MnNi0.5. Electrochemical results in 3.5 % NaCl solution show that the alloying elements Ti and Si have a negative influence on the corrosion resistance of the Al0.3CrFe1.5MnNi0.5alloys.     

Microstructure and mechanical performance of new Al0.5CrFe1.5MnNi0.5 high-entropy alloys improved by plasma nitriding

Effects of plasma nitriding at 525 °C on microstructure and mechanical performance of a brand-new Al_0.5CrFe_1.5MnNi_0.5 high-entropy alloy (HEA) were investigated. This alloy exhibits a large age hardening effect at temperatures from 600 to 800 °C and can be well-nitrided in the as-cast condition or the homogenized and furnace-cooled state. The nitrided layer has a thickness around 75 μm and a peak hardness level of Hv 1250 near the surface. The nitrided Al_0.5CrFe_1.5MnNi_0.5 alloys exhibit superior adhesive wear resistance to conventional nitrided steels by 25-54 times due to their much thicker highly-hardened layer and higher peak hardness than that of conventional steels.     

The effect of molybdenum on the corrosion behaviour of the high-entropy alloys Co1.5CrFeNi1.5Ti0.5Mox in aqueous environments

The purpose of this study is to investigate the electrochemical properties of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x high-entropy alloys in three aqueous environments which simulate acidic, marine, and basic environments at ambient temperature (∼25 °C). The potentiodynamic polarisation curves of the Co_1.5CrFeNi_1.5Ti_0.5Mo_x alloys, obtained in aqueous solutions of H₂SO₄ and NaOH, clearly revealed that the corrosion resistance of the Mo-free alloy was superior to that of the Mo-containing alloys. On the other hand, the lack of hysteresis in cyclic polarisation tests and SEM micrographs confirmed that the Mo-containing alloys are not susceptible to pitting corrosion in NaCl solution.     

Aluminum Alloying Effects on Lattice Types, Microstructures, and Mechanical Behavior of High-Entropy Alloys Systems

The crystal lattice type is one of the dominant factors for controlling the mechanical behavior of high-entropy alloys (HEAs). For example, the yield strength at room temperature varies from 300 MPa for the face-centered-cubic (fcc) structured alloys, such as the CoCrCuFeNiTi _x system, to about 3,000 MPa for the body-centered-cubic (bcc) structured alloys, such as the AlCoCrFeNiTi _x system. The values of Vickers hardness range from 100 to 900, depending on lattice types and microstructures. As in conventional alloys with one or two principal elements, the addition of minor alloying elements to HEAs can further alter their mechanical properties, such as strength, plasticity, hardness, etc. Excessive alloying may even result in the change of lattice types of HEAs. In this report, we first review alloying effects on lattice types and properties of HEAs in five Al-containing HEA systems: Al _x CoCrCuFeNi, Al _x CoCrFeNi, Al _x CrFe_1.5MnNi_0.5, Al _x CoCrFeNiTi, and Al _x CrCuFeNi₂. It is found that Al acts as a strong bcc stabilizer, and its addition enhances the strength of the alloy at the cost of reduced ductility. The origins of such effects are then qualitatively discussed from the viewpoints of lattice-strain energies and electronic bonds. Quantification of the interaction between Al and 3d transition metals in fcc, bcc, and intermetallic compounds is illustrated in the thermodynamic modeling using the CALculation of PHAse Diagram method.     

Analysis of the electrochemical reaction behavior of alloy AZ91 by EIS technique in H3PO4/KOH buffered K2SO4 solutions

The EIS technique was used to analyze the electrochemical reaction behavior of Alloy AZ91 in H₃PO₄/KOH buffered K₂SO₄ solution at pH 7. The corrosion resistance of Alloy AZ91 was directly related with the stability of Al₂O₃ · xH₂O rich part of the composite oxide/hydroxide layer on the alloy surface. The break down of the oxide layer was estimated to occur mainly on the matrix solid solution phase in Alloy AZ91. The mf capacitive loop arose from the relaxation of mass transport in the solid oxide phase in the presence of Al₂O₃ · xH₂O rich part and from Mg⁺ ion concentration within the broken area in the absence of Al₂O₃ · xH₂O rich part in the composite oxide structure on the alloy surface. The lf inductive loop had tendency of disappear when the dissolution rate of the alloy decreased as a result of the formation of the protective oxide layer.     

FeCoNiCrCu0.5Alx高熵合金的结构和性能（英文）

研究Al含量和热处理对FeCoNiCrCu0.5Alx多主元高熵合金的相结构、硬度和电化学性能的影响规律。随着Al含量的增加,铸态合金的相结构由FCC相向BCC相转变。当x从0.5增加到1.5时,FeCoNiCrCu0.5Alx高熵合金的稳定结构由FCC结构向FCC+BCC双相结构转变。BCC相的硬度高于FCC相的,在氯离子及酸性介质中BCC相的耐腐蚀性均优于FCC相的。FeCoNiCrCu0.5Al1.0铸态合金具有高硬度和良好的抗腐蚀性能。     

Corrosion behaviour of magnesium/aluminium alloys in 3.5 wt.% NaCl

Corrosion behaviour of commercial magnesium/aluminium alloys (AZ31, AZ80 and AZ91D) was investigated by electrochemical and gravimetric tests in 3.5 wt.% NaCl at 25 °C. Corrosion products were analysed by scanning electron microscopy, energy dispersive X-ray analysis and low-angle X-ray diffraction. Corrosion damage was mainly caused by formation of a Mg(OH)₂ corrosion layer. AZ80 and AZ91D alloys revealed the highest corrosion resistance. The relatively fine β-phase (Mg₁₇Al₁₂) network and the aluminium enrichment produced on the corroded surface were the key factors limiting progression of the corrosion attack. Preferential attack was located at the matrix/β-phase and matrix/MnAl intermetallic compounds interfaces.     

Direct active soldering of Al0.3CrFe1.5MnNi0.5 high entropy alloy to 6061-Al using Sn-Ag-Ti active solder

Al_0.3CrFe_1.5MnNi_0.5 high entropy alloys (HEA) have special properties. The microstructures and shear strengths of HEA/HEA and HEA/6061-Al joints were determined after direct active soldering (DAS) in air with Sn3.5Ag4Ti active filler at 250 °C for 60 s. The results showed that the diffusion of all alloying elements of the HEA alloy was sluggish in the joint area. The joint strengths of HEA/HEA and HEA/6061-Al samples, as analyzed by shear testing, were (14.20±1.63) and (15.70±1.35) MPa, respectively. Observation of the fracture section showed that the HEA/6061-Al soldered joints presented obvious semi-brittle fracture characteristics.     

Electrochemical response of AlNiLa amorphous and devitrified alloys

The electrochemical response of Al_94−xNi₆La_x alloys (x = 4, 5, 6, 7) after different stages of devitrification was studied in 0.05 M Na₂SO₄ as well as in different concentrations [0.001 M, 0.01 M and 0.1 M] NaCl solutions. Complementary crystallization studies were carried out to elucidate the composition dependent phase evolution in these alloys. It was observed that the primary crystallization did not cause any deterioration in the corrosion resistance of the alloys as compared to the amorphous alloys. In the case of Al₈₇Ni₆La₇, there was actually an improvement in the passivating ability in benign media. The various primary crystalline phases in the different alloys investigated did not cause different electrochemical responses. However, the onset of secondary crystallization caused a reduction in the corrosion resistance in the NaCl media through a loss in passivating ability of all the alloys. This is due to increased galvanic activity as well as the loss of the amorphous phase.     

Modelling the corrosion behaviour of Al2CuMg coarse particles in copper-rich aluminium alloys

The corrosion behaviour of 2024 aluminium alloy in sulphate solutions was studied; attention was focused on the influence of coarse intermetallic Al₂CuMg particles on the corrosion resistance of the alloy. Model alloys representative of the aluminium matrix and of Al₂CuMg coarse intermetallics were synthesized by magnetron sputtering. Open-circuit potential measurements, current-potential curve plotting and galvanic coupling tests were performed in sulphate solutions with or without chlorides. Further explanations were deduced from the study of the passive films grown on model alloys in sulphate solutions. The results showed that model alloys are a powerful tool to study the corrosion behaviour of aluminium alloys.     

Electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd in NaCl solution

The electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd (x = 0, 1, 2 and 4 wt.%) alloys in 3.5% NaCl solution was investigated. The corrosion behavior of the alloys was assessed by open circuit potential measure, potentiodynamic polarization, and electrochemical impedance spectroscopy. The electrochemical results show the intermetallic precipitates with Nd behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. During corrosion, Al₂O₃ and Nd₂O₃, in proper ratio, is incorporated into the corrosion film, and enhances the corrosion resistance.     

Electrochemical corrosion characteristics of ZrNi5−xCox alloys

The electrochemical corrosion behaviour of a series of ZrNi_5−xCo_x alloys with x=0-4 has been tested using potentiokinetic polarisation technique. The polarisation curves were measured in deaerated 0.5 M sulphate solutions with pH=0.2-7 and in strong alkaline solution of KOH (pH=15). It is shown that the presence of greater amounts of Co in the alloy (x?2) worsens the passivating properties of the alloy in acidified sulphate solutions. On the other hand, in strong alkaline solutions, both low- and high-cobalt alloys undergo stable passivation. The degree of Ni substitution by Co in the alloys does not generally affect the shape of cathodic polarisation curves.     

Electrochemical passive properties of AlxCoCrFeNi (x = 0, 0.25, 0.50, 1.00) alloys in sulfuric acids

This study investigates the electrochemical passive properties of Al_xCoCrFeNi alloys in H₂SO₄ by potentiodynamic polarization, EIS, and weight loss tests from 20 to 65 °C. Experimental results indicate that Al harms the corrosion resistance in H₂SO₄ at temperatures exceeding 27 °C owing to the porous and inferior nature of the protection oxide film of Al in these alloys. Closely examining the Arrhenius plots of corrosion current density reveals that both pre-exponential factor A and activation energy E_a increase with Al content. However, A affects corrosion current density more significantly than E_a at higher temperatures and, conversely, at lower temperatures.     

The effects of lanthanum on microstructure and electrochemical properties of Al–Zn–In based sacrificial anode alloys

In order to improve the non-uniform corrosion of Al–0.5Zn–0.03In–1Mg–0.05Ti alloys, Al–5Zn–0.03In–1Mg–0.05Ti–xLa (x = 0.3, 0.5 and 0.7 wt.%) alloys were developed. Microstructures and electrochemical properties of the alloys were investigated. The results show that the optimal microstructures and electrochemical properties are obtained in Al–5Zn–0.03In–1Mg–0.05Ti–0.5La alloy. The main precipitate phase is Al₂LaZn₂ particles. The excellent electrochemical properties of Al–5Zn–0.03In–1Mg–0.05Ti–0.5La alloy is mainly attributed to fine grains and grain boundaries containing fine Al₂LaZn₂ precipitates. At the same time the fine grains can improve the non-uniform corrosion of Al–0.5Zn–0.03In–1Mg–0.05Ti alloy.     

Effect of tin on high-temperature sulphidation of Fe-Cr alloys in H2/H2S atmospheres

The high temperature sulphidation behaviour of Fe-46Cr-xSn (x = 0; 0.2; 0.5; 1; 2) alloys has been studied at temperatures of 1073, 1173 and 1273 K in H₂/H₂S mixtures with different sulphur vapour partial pressures of 10⁻¹, 10⁻³ and 10⁻⁵ Pa. Thermogravimetric studies in combination with scanning electron microscope (SEM), with energy dispersive spectrometer (EDS), and X-ray diffraction (XRD) techniques, have displayed a significant influence of the sulphur partial pressure on the composition and growth rate of the sulphide scale. The results have shown that addition of tin increases the sulphidation rate of Fe-46Cr alloys but not considerably (except at temperatures of 1073 and 1173 K combined with sulphur partial pressure of 10⁻⁵ Pa). The metallic core of the studied samples was enriched in tin and iron, moreover tin was found in the internal layer close to the metallic core as metallic Fe_xSn_y inclusions with tin concentrations of up to 12 at.%.     

Passivation of Al–Cr–Fe and Al–Cu–Fe–Cr complex metallic alloys in 1 M H2SO4 and 1 M NaOH solutions

The corrosion mechanisms of Al–Cr–Fe and Al–Cu–Fe–Cr complex metallic alloys have been investigated by potentiodynamic and potentiostatic polarization. Very good passivation of the Al–Cr–Fe surface is exhibited from 1 M H₂SO₄ to 1 M NaOH solutions, which was confirmed by ICP-OES analysis over a period of 273 days. Potentiostatically formed passive films analysed by XPS revealed chromium enrichment in the outermost layer of the aluminium oxy-hydroxide film. Although Al–Cu–Fe–Cr showed passivation during potentiodynamic polarization, heavy active corrosion at OCP was revealed by ICP-OES. For the Al–Cu–Fe–Cr alloy, the 10% content of Cr is insufficient to maintain a protective “chemically stable” Cr oxide/hydroxide.     

Corrosion behaviour of intermetallic aluminide coatings on nitrogen-containing austenitic stainless steels

The present work reports the effect of aluminide layers on the aqueous corrosion behaviour of four different 316L stainless steels containing various nitrogen contents (0.015%, 0.1%, 0.2% and 0.56% N). Diffusion annealed aluminide layers are generated over the surface by heat treatment of the aluminium precoated alloys at 750 °C for 25 h in nitrogen atmosphere. X-ray diffraction patterns of the surface modified samples showed the presence of AlN, Al₁₃Fe₄ and FeAl₂ phases. Diffusion of aluminum into the alloy, and the formation of AlN by the reaction of aluminium with matrix nitrogen, was identified using secondary ion mass spectrometry (SIMS). The nitrogen peak in the diffused layer was found to increase with increasing nitrogen content of the base alloy. SEM observation of cross-sectionally mounted alloys showed the presence of spherical AlN phase in addition to iron aluminide intermetallic phases. The role of such a composite surface layer containing intermetallic aluminides and nitride on the corrosion resistance of austenitic stainless steels in 0.5 M NaCl and 0.5 M sulphuric acid is discussed in greater detail based on open circuit potential (OCP)–time measurements, potentiodynamic polarisation studies and electrochemical impedance spectroscopy (EIS) investigations. The aluminide layered alloy with 0.1% N content showed better corrosion performance. The presence of nitrogen was found to have a positive effect in enhancing the hardness of the composite layer. Role of matrix nitrogen on the microstructure and microchemical distribution at the surface, and its role on corrosion resistance in acidic and chloride media are discussed in detail.     

Corrosion behaviour of Al/Al3Ti and Al/Al3Zr functionally graded materials produced by centrifugal solid-particle method: Influence of the intermetallics volume fraction

Intermetallic particles, Al₃Ti and Al₃Zr were formed in Al–5mass%Ti and Al–5mass%Zr alloys, respectively, by centrifugal casting, in order to create functionally graded materials (FGMs). At present, no information is available on the influence of the amount of intermetallics on the electrochemical properties of these alloys.In this paper, the corrosion resistance of Al/Al₃Ti and Al/Al₃Zr FGMs was investigated by open-circuit measurements, potentiodynamic polarization and electrochemical impedance spectroscopy. Results suggests that the corrosion resistance of the FGMs is affected by galvanic effects between the intermetallic particles and the metallic matrix. Lower centrifugal forces resulted in an improvement of the electrochemical properties.     

Corrosion behaviour of dc magnetron sputtered Fe1−xMgx alloy films in 3 wt% NaCl solution

Fe_1−xMg_x alloy films (with x ? 43.4 at.% Mg) were deposited by dc magnetron sputtering onto glass slide substrates. The objective of this study was to characterise the corrosion properties of these alloys in saline solution for application as new friendly environmentally sacrificial coatings in the protection of steel structures. The morphological and structural properties of the alloys were systematically studied prior to electrochemical experiments, and then the degraded surfaces were analysed to determine the composition and nature of corrosion products. Alloys with <25  at.% Mg were single-phase body-centred cubic (bcc) with enlarged lattice parameters, whereas for magnesium contents above 25 at.%, amorphisation occurred. The reactivity of the alloys in saline solution is strongly dependent on the Mg content and the alloy structure. The incorporation of magnesium leads to an open circuit potential shift of the alloy towards more negative values, that confers an attractive interest of these alloys as sacrificial coatings. A transition in corrosion activity is observed at 25 at.% Mg from which the reactivity decreases with the magnesium content increase. The evolution of the alloy corrosion behaviour is discussed in terms of structural and corrosion products evolution versus magnesium content.     

Comparison of the corrosion of Cu50Pd50 and Cu50Pd44M6 (M = Y,Mg, or Al) hydrogen separation membrane alloys in simulated syngas containing H2S

The resistance to sulfidation was examined by exposing coupons including a Cu–Pd binary alloy and three ternary alloys with 6 at% Y, Mg, or Al to simulated syngas containing varying amounts of H₂S. The mass change of the samples was determined and the exposed surfaces were characterized by SEM/EDS and XRD. The best corrosion resistance of the ternary alloys was observed in the Cu₅₀Pd₄₄Al₆ alloy. A slight decrease was observed when Mg was added, but both the Al and Mg alloys were roughly on par with the binary composition. The Y addition resulted in a degradation in the corrosion resistance by forming extensive internal Y₂O₃ and Cu_1−xY_xS and external Pd_4−xCu_xS and Pd ₁₃Cu₃S₇.