Conversion coating treatment for AZ91 magnesium alloys by a permanganate‐REMS bath

A permanganate‐rare earth metal salt (REMS) chemical conversion bath was applied to a sample of AZ91 magnesium alloy in this study, a red‐brown conversion coating formed subsequently on the sample surface. The test results of this coating with a scanning electron microscope (SEM) showed that there existed net‐like cracks on the surface of the treated magnesium alloy. With the analyses of X‐ray Diffraction (XRD) and X‐ray Photoelectron Spectroscopy (XPS), a further study of this coating indicated that the coating was structurally amorphous and mainly composed of CeO₂, MnO, MnO₂, MgO, Mg(OH)₂ and MgAl₂O₄. Furthermore, the electrochemical polarization tests showed that compared with the samples treated by the chrome‐based method, the open‐circuit potential of the magnesium alloy coated in permanganate‐REMS bath moved from ? 1.34 V_SCE to ? 1.28 V_SCE and the anodic current density of the alloy, at the same potential, decreased evidently in simulated sweat fluid. The cracks in the chemical conversion coating should be caused by the phase structure of the magnesium alloy. During the chemical conversion process, the localized corrosion micro‐cell led to the formation of the net‐like cracks on the surface. Simultaneously, the dehydration of the surface coating after treatment also accelerated the formation of the cracks at the coating surface.     

Enhanced corrosion resistance of magnesium and its alloys through the formation of cerium (and aluminium) oxide surface films

Cerium (and aluminium) oxide layers were formed on magnesium and its alloys (AZ91) by chemical surface treatment with or without subsequent annealing. The corrosion behaviour modifications provided by the formation of these surface films were studied by means of different electrochemical and surface analysis techniques. The electrochemical behaviour, studied in sodium sulphate (Na₂SO₄) solution, showed (i) a marked shift of the corrosion potential towards more positive values, (ii) a slight inhibition of the cathodic reaction and (iii) a significant decrease of the anodic dissolution current. X‐ray photoelectron spectroscopy (XPS) was used for the characterisation of the composition of the deposited films and of the changes in the film composition during the electrochemical corrosion tests. The components of some oxide films are cerium dioxide (CeO₂), aluminium oxide (Al₂O₃) and aluminium hydroxide (Al(OH)₃). Other metallic mixed oxide films were obtained as a function of the solution composition. Very little (or no) change in the oxide film composition during the cathodic and anodic polarization experiments was observed from XPS measurements. Chemical treatment provides thick and moderately adherent protective oxide films. Annealing under oxygen further improves the beneficial effect of the chemical treatment.     

Corrosion behaviour of magnesium in ethylene glycol

Corrosion of magnesium engine components by coolant is an important issue in the automotive industry where magnesium alloys may be used. It is of significance to understand the corrosion behaviour of pure magnesium in ethylene glycol solutions, as this can provide a basis for developing new coolants for magnesium alloy engine blocks. In this paper, through corrosion and electrochemical tests, it was found that the corrosion rate of magnesium decreased with increasing concentration of ethylene glycol. Individual contaminants, such as NaCl, NaHCO₃, Na₂SO₄ and NaCl can make aqueous ethylene glycol solution more corrosive to magnesium. However, in NaCl contaminated ethylene glycol, NaHCO₃ and Na₂SO₄ showed some inhibition effect. The solution resistivity played an important role in the corrosion of magnesium in ethylene glycol solutions, and the competitive adsorption of ethylene glycol and the contaminants on the magnesium surface was also responsible for the observed corrosion behaviours. The corrosion of magnesium in ethylene glycol can be effectively inhibited by addition of fluorides that react with magnesium and form a protective film on the surface.     

Corrosion processes of Mg–Y–Nd–Zr alloys in Na2SO4 electrolyte

The corrosion behavior of Mg–Y–Nd–Zr (WE43 commercial alloy) was investigated in Na₂SO₄ electrolyte using potentiodynamic polarization curves, X-Ray Photoelectron Spectroscopy (XPS), Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) depth profiles, Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDS) analyzes. SEM and EDS data show that Nd-rich precipitates are mainly located at the grains boundaries. Zr/Y-rich zones are distributed inside the most of the grains. XPS study indicates a depletion of Mg on surface that could be attributed to Mg dissolution and an enrichment of the addition element oxides. XPS and ToF-SIMS analyzes demonstrate that the corrosion films are made up of a magnesium hydroxide (Mg(OH)₂) outer layer and an inner layer containing magnesium oxide (MgO), yttrium oxide (Y₂O₃) and hydroxide (Y(OH)₃), mixed with a small amount of MgH₂, zirconium oxide (ZrO₂) and neodymium oxide (Nd₂O₃). The Y₂O₃ and Y(OH)₃ signals increase slightly in the inner layer towards the corrosion film/alloy interface. Unlike these compounds, ZrO₂ and Nd₂O₃ compound signals are constant inside the inner layer. It is concluded that: (i) neodymium, zirconium and yttrium play a key role in the slightly improved corrosion resistance of the alloy and (ii) the cathodic reaction is slower on WE43 than on pure Mg and AZ91.     

Formation of dicalcium phosphate dihydrate on magnesium alloy by micro-arc oxidation coupled with hydrothermal treatment

A layer containing dicalcium phosphate dihydrate (DCPD) and β-Ca₃(PO₄)₂ was prepared on magnesium alloy by hydrothermal treatment of micro-arc oxide (MAO) layer. The biocorrosion resistance of the oxide layers before and after hydrothermal treatment was analyzed by anodic polarization and electrochemical impedance spectroscopy (EIS) in Hank’s solution. The prepared MAO layers consisted mainly of MgO and MgAl₂O₄, and Ca and P inside the oxide layers existed with amorphous phase. Hydrothermal treatments not only made the amorphous Ca and P change into DCPD and β-Ca₃(PO₄)₂ crystals, but also improved the biocorrosion resistance of magnesium alloys, especially the pitting corrosion resistance.     

Hot corrosion behaviour of a cobalt-base super-alloy K40S with and without NiCrAlYSi coating

A NiCrAlYSi coating was deposited by arc ion plating on a cobalt-base super-alloy K40S to improve its hot corrosion resistance at 1173 K in air. The K40S suffered from accelerated corrosion and formed non-protective scale with poor adherence when its surface was beneath Na₂SO₄ and Na₂SO₄ containing 25 wt.% NaCl salt deposits. After the K40S was coated with NiCrAlYSi coating, a protective α-Al₂O₃ scale was formed on the coating. Although the NiCrAlYSi coating changed into NiCoCrAlYSi during corrosion processes, it still possessed good corrosion resistance. In addition, the corrosion mechanisms were discussed on a basis of basic fluxing model.     

Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

Passivity of polycrystalline NiMnGa alloys for magnetic shape memory applications

The corrosion and passivation behaviour of bulk polycrystalline martensite Ni₅₀Mn₃₀Ga₂₀ and austenite Ni₄₈Mn₃₀Ga₂₂ alloys was compared in electrolytes with different pH values. Linear anodic and cyclic potentiodynamic polarisation methods and anodic current transient measurements have been conducted for the alloys and their constituents to analyze free corrosion, anodic dissolution and passive layer formation processes. Electrochemically treated alloy surfaces were characterized with scanning electron microscopy (SEM) and angle-resolved x-ray photoelectron spectroscopy (XPS). The electrochemical response of both alloys is in principal similar and is dominated by the Ni oxidation. In acidic solutions (pH 0.5 and 5) a slightly higher reactivity is detectable for the martensitic alloy which is mainly attributed to enhanced dissolution processes at the multiple twin boundaries. In weakly acidic to strongly alkaline solutions (pH 5-11) both alloys exhibit a low corrosion rate and a stable anodic passivity. While air-formed films comprise NiOOH, Ga₂O₃ and MnO₂, passive films formed in near neutral media (pH 5-8.4) are composed of Ni(OH)₂, NiOOH and Ga₂O₃ in the outer region and of NiO, MnO₂ and MnO in the metal-near region.     

Corrosion behaviour of die-cast AZ91D magnesium alloy in aqueous sulphate solutions

The corrosion behaviour of die-cast AZ91D magnesium alloys in sulphate solutions was investigated by SEM, FTIR and polarization measurements. For immersion times less than 48 h, no pitting corrosion occurred and only generalized corrosion was apparent. According to the polarization curves, the corrosion rate order of the die-cast AZ91D Mg alloy in three aqueous solutions was: NaCl > MgSO₄ > Na₂SO₄. The main corrosion products were Mg(OH)₂ and MgAl₂(SO₄)₄·22H₂O in the sulphate solutions and the product film was compact. Precipitation of MgAl₂(SO₄)₄·22H₂O required a threshold immersion time.     

Corrosion behaviour of chemical conversion treatments on as-cast Mg-Al alloys: Electrochemical and non-electrochemical methods

Magnesium alloys are often used in as-cast conditions. So, the aim of this work is to characterize the corrosion protection of as-cast AZ91D alloys coated with simple chemical conversion (phosphate-permanganate, and cerium-based coatings).With the two coatings, the electrochemical measurements show that the corrosion protection is due to both the inhibition of cathodic and anodic reactions, because of the presence of stable CeO₂ or manganese oxides in basic pH.Nevertheless, the non-electrochemical tests of corrosion are required to bring to light the healing effect of phosphate-permanganate coating compared to Ce-coating and to describe the corrosion behaviour completely. Finally phosphoric and soda pickling associated to phosphate-permanganate conversion treatment or cerium coating are ecologically efficient alternatives to fluoride-based pickling and the chromating treatment.     

Electrochemical study on hot corrosion of Si-modified aluminide coated In-738LC in Na2SO4-20 wt.% NaCl melt at 750 °C

The corrosion performance of the slurry Si-modified aluminide coating on the nickel base superalloy In-738LC exposed to low temperature hot corrosion condition has been investigated in Na₂SO₄-20 wt.% NaCl melt at 750 °C by combined use of the anodic polarization and characterization techniques.The coated specimen showed a passive behavior up to −0.460 V vs. Ag/AgCl (0.1 mol fraction) reference electrode, followed by a rapid increase in anodic current due to localized attack in the higher potential region. In the passive region, the anodic dissolution of constituents of the coating occurred through the passive film, probably SiO₂, at slow rate of 20-30 μA/cm². The passive current for the Si-modified coating was two orders of magnitude smaller than that for bare In-738LC, which is known as Cr₂O₃ former in this melt. This indicates that the SiO₂ film is chemically more stable than Cr₂O₃ film under this condition. However, pitting-like corrosion commenced around −0.460 V and proceeded at the high rate of 100 mA/cm² in the higher potential region than +0.400 V. The corrosion products formed on the coating polarized in different anodic potentials were characterized by SEM, EDS and XRD. It was found from the characterization that oxidation was dominant attack mode and no considerable sulfidation occurred at 750 °C. The SiO₂ oxide was not characterized in the passive region because the thickness of the passive film was extremely thin, but was detected as the primary oxide in the localized corrosion region, where the selective oxidation of Al was observed by further progress of the corrosion attack front into the inner layer of coating.     

Comparison of electrochemical corrosion behaviour of MgO and ZrO2 coatings on AM50 magnesium alloy formed by plasma electrolytic oxidation

Two types of PEO coatings were produced on AM50 magnesium alloy using pulsed DC plasma electrolytic oxidation process in an alkaline phosphate and acidic fluozirconate electrolytes, respectively. The phase composition and microstructure of these PEO coatings were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The corrosion behaviour of the coated samples was evaluated by open circuit potential (OCP) measurements, potentiodynamic polarization tests, and electrochemical impedance spectroscopy (EIS) in neutral 0.1 M NaCl solution. The results showed that PEO coating prepared from alkaline phosphate electrolyte consisted of only MgO and on the other hand the one formed in acidic fluozirconate solution was mainly composed of ZrO₂, MgF₂. Electrochemical corrosion tests indicated that the phase composition of PEO coating has a significant effect on the deterioration process of coated magnesium alloy in this corrosive environment. The PEO coating that was composed of only MgO suffered from localized corrosion in the 50 h exposure studies, whereas the PEO coating with ZrO₂ compounds showed a much superior stability during the corrosion tests and provided an efficient corrosion protection. The results showed that the preparation of PEO coating with higher chemical stability compounds offers an opportunity to produce layers that could provide better corrosion protection to magnesium alloys.     

Electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd in NaCl solution

The electrochemical corrosion behavior of Mg-5Al-0.4Mn-xNd (x = 0, 1, 2 and 4 wt.%) alloys in 3.5% NaCl solution was investigated. The corrosion behavior of the alloys was assessed by open circuit potential measure, potentiodynamic polarization, and electrochemical impedance spectroscopy. The electrochemical results show the intermetallic precipitates with Nd behave as less noble cathodes in micro-galvanic corrosion and suppress the cathodic process. During corrosion, Al₂O₃ and Nd₂O₃, in proper ratio, is incorporated into the corrosion film, and enhances the corrosion resistance.     

Structural Aspects of the Behavior of Lead-Free Solder in the Corrosive Solution

In oxidizing environments, most tin-based lead (Pb)-free alloys form a tin oxide that is easily eroded or mechanically damaged, affecting corrosion resistance and thus reliability of the soldered joints. In this study, the effect of microstructure heterogeneity on corrosion behavior of Pb-free solder candidate systems has been investigated on the example of as-cast and heat-treated alloys. The research was focused on a comparison between the corrosion resistance of binary Sn-Zn and ternary Sn-Zn-Cu alloys. Accelerated corrosion tests were performed by means of electrochemical methods in the sodium sulfate solution (VI), Na₂SO₄, of about 0.5 M concentration, pH adjusted to 2 by means of concentrated H₂SO₄ acid. In these tests, the corrosion potentials as well as polarization curves were determined for the selected alloys in as-cast state and after their heat treatment using different combinations of processing parameters. The measurements of basic electrochemical characteristics were made, i.e., the corrosion current (i _corr μA/cm²) and Tafel coefficients, both cathodic (b _c V/dec) and anodic (b _a V/dec) ones. Detailed structural characterization of as-cast and heat-treated alloys before and after accelerated corrosion tests has been made under a wide range of magnifications using light microscopy and scanning electron microscopy observations. The results showed that structural heterogeneity of the examined alloys, attributed to the presence of secondary phases, and affected by their size and distribution, significantly influences the behavior of the examined Pb-free Sn-Zn-based alloys in the corrosive environment.     

环氧涂层中锌铬黄颜料对镁合金的防蚀机理

采用电化学阻抗、动电位极化、开路电位监测和X射线光电子能谱(XPS)等手段,研究了环氧涂层中锌铬黄颜料对镁合金的腐蚀防护作用,并分析了其防蚀机理。结果表明,锌铬黄防锈颜料均匀分散在涂层中,增强了涂层的屏蔽性能以及涂层与镁合金基体的结合力;在3%NaCl水溶液中,锌铬黄是一种阳极型缓蚀剂,它依靠铬酸根离子的阳极钝化作用形成钝化膜,阻滞了阳极腐蚀过程,造成涂层试样开路电位正移,使涂层试样的阳极极化增大。     

Hot corrosion of materials: Fundamental studies

Hot corrosion is the accelerated oxidation of materials at elevated temperatures induced by a thin film of fused salt deposit. Because of its high thermodynamic stability in the mutual presence of sodium and sulfur impurities in an oxidizing gas, Na₂SO₄ is often found to be the dominant salt in the deposit. The corrosive oxyanion-fused salts are usually ionically conducting electrolytes that exhibit an acid/base chemistry, so that hot corrosion must occur by an electrochemical mechanism that may involve fluxing of the protective oxides. With the aid of high-temperature reference electrodes to quantify an acid/base scale, the solubilities for various metal oxides in fused Na₂SO₄ have been measured, and these show remarkable agreement with the theoretical expectations from the thermodynamic phase stability diagrams for the relevant Na-Metal-S-O systems. The solubilities of several oxides infused Na₂SO₄-NaVO₃ salt solutions have also been measured and modeled. Such information is important both in evaluating the corrosion resistance of materials and in interpreting any oxide fluxing/reprecipitation mechanisms. Various electrochemical measurements have identified the S₂O₇ ^2? anion (dissolved SO₃) as the oxidant that is reduced in the hot corrosion process. Electrochemical polarization studies have elucidated the corrosion reactions and clarified the corrosion kinetics of alloys. Mechanistic models for Type I and Type II hot corrosion are discussed briefly.     

Influence of second phases on the electrochemical behavior of hot dipped Al-Mg-Si coated steel

The influence of second phases on the electrochemical behavior of hot dipped Al-Mg-Si coated steel has been investigated using an open circuit potential (OCP) and anodic polarization measurements. The results of OCP monitoring data for Mg₂Si particles show fast ennoblement of OCP then slowly rise until the last stage of monitoring. The localized corrosion starts from the surrounding matrix of Mg₂Si particles and propagates in the coating surface. The passivation of the Al-Mg-Si coating surface during anodic polarization can be attributed to the formation of the surface oxide film, which inhibits further dissolution of the coating.     

A study of the inhibition of iron corrosion by imidazole and its derivatives self-assembled films

The self-assembled (SA) films of imidazole and its derivatives were prepared on the iron surface. The protection abilities of these films against iron corrosion in 0.5 M H₂SO₄ solution were investigated using electrochemical impedance spectroscopy (EIS) and polarization techniques. The results of EIS and polarization curves demonstrated that films of the imidazole and its derivatives were able to protect iron from corrosion effectively. XPS was also used for the surface analysis, the results from XPS confirmed the adsorption of imidazole derivatives on the iron surface by monitoring the functional group peaks of the compounds.     

Effect of antimony on the corrosion behavior of low-alloy steel for flue gas desulfurization system

The alloying effect of Sb in a new low-alloy steel for the purpose of FGD materials was investigated by potentiodynamic polarization, linear polarization resistance measurement, electrochemical impedance spectroscopy (EIS) and weight loss measurements in an aggressive solution of 16.9 vol.% H₂SO₄ + 0.35 vol.% HCl (modified green death solution) at 60 °C, pH −0.3. All measurements confirmed the marked improvement in the corrosion behavior of the low-alloy steel via the addition of a small amount of Sb, particularly for the 0.10Sb steel. Pitting corrosion was detected by scanning electron microscopy (SEM) on the surface of blank steel and 0.05Sb steel, but not 0.10Sb steel, after weight loss measurements. X-ray photoelectron spectroscopy (XPS) analysis of the corroded surfaces after EIS and linear polarization measurements showed that the decrease in corrosion rates was due to the formation of a protective Sb₂O₅ oxide film on the surface of the Sb-containing steels. Moreover, the addition of 0.10% Sb stimulated the development of high corrosion inhibiting, Cu-containing compounds which further inhibited the anodic and cathodic reactions.     

Effects of solution pH and Cl on electrochemical behaviour of an Aermet100 ultra-high strength steel in acidic environments

In this work, the effects of solution pH and Cl⁻ on the electrochemical behaviour of an Aermet100 ultra-high strength steel in 0.5 M (Na₂SO₄ + H₂SO₄) solution were studied by polarization curve and electrochemical impedance spectroscopy (EIS) measurements, combined with scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) characterization. The results show that, when solution pH is below 4, the steel is in the active dissolution state, and corrosion current decreases with the increase of pH. There exists a critical pH value, above which the steel is passivated. Moreover, the oxides and hydroxides of Fe, Co, Ni and Cr are the primary components of the passive film. With addition of Cl⁻, pits are initiated on the steel electrode.