Corrosion behavior of Ti-Mo alloys cold rolled and heat treated

Corrosion behavior of (α + β) Ti-10Mo and β Ti-20Mo (mass%) alloys cold rolled and solution heat treated was investigated by studying the anodic polarization curves at 310 K in 5 mol% HCl solution to determine the potential use of those alloys in biomedical applications. The anodic films formed on the surfaces of the alloys were examined using X-ray photoelectron spectroscopy analysis and scanning electron microscopy. The results reveal that both of the Ti-Mo alloys cold rolled and solution treated exhibit a passive behavior in 5% HCl solution, which is attributed to the passive film formation of a mixture of MoO₃ and TiO₂. The cold rolling process does not influence the formation of passive films on the Ti-Mo alloys although it slightly increases the passive current densities. The corrosion resistance of the Ti-Mo alloys increases with Mo content and both of the Ti-Mo alloys exhibit better corrosion resistance than commercial pure Ti—the currently used metallic biomaterial.     

Formation and breakdown of surface films on magnesium and its alloys in aqueous solutions

The influences of surface films formed by open-circuit exposure to neutral solutions on the corrosion and electrochemical behaviour of pure Mg and Mg alloys have been examined by in situ ellipsometric analysis and electrochemical measurements. Surface films mainly composed of Mg(OH)₂ grew rapidly during open-circuit exposure to 0.1 M NaCl and 0.1 M Na₂SO₄ solutions. These films had protective ability to passivate Mg in the solutions. However, they suffered local breakdown under anodic polarisation. The passive current density decreased and the breakdown potential increased with increasing immersion time and film thickness. Influences of purity and alloying elements on the passivity and its breakdown of Mg have been discussed.     

Stress corrosion cracking study of microalloyed pipeline steels in dilute NaHCO3 solutions

Studies were carried out to evaluate the stress corrosion cracking (SCC) behavior of a X-70 microalloyed pipeline steel, with different microstructures by using the slow strain rate testing (SSRT) technique at 50 °C, in NaHCO₃ solutions. Both anodic and cathodic potentials were applied. Additionally, experiments using the SSRT technique but with pre-charged hydrogen samples and potentiodynamic polarization curves at different sweep rates were also carried out to elucidate hydrogen effects. The results showed that the different microstructures in conjunction with the anodic applied potentials shift the cracking susceptibility of the steel. In diluted NaHCO₃ solutions cathodic potentials close to their rest potential values decreased the SCC susceptibility regardless the microstructure, whereas higher cathodic potentials promote SCC in all steel conditions. Certain microstructures are more susceptible to present anodic dissolution corrosion mechanism. Meanwhile concentrated solution did not promotes brittle fracture.     

Electrochemical response of AlNiLa amorphous and devitrified alloys

The electrochemical response of Al_94−xNi₆La_x alloys (x = 4, 5, 6, 7) after different stages of devitrification was studied in 0.05 M Na₂SO₄ as well as in different concentrations [0.001 M, 0.01 M and 0.1 M] NaCl solutions. Complementary crystallization studies were carried out to elucidate the composition dependent phase evolution in these alloys. It was observed that the primary crystallization did not cause any deterioration in the corrosion resistance of the alloys as compared to the amorphous alloys. In the case of Al₈₇Ni₆La₇, there was actually an improvement in the passivating ability in benign media. The various primary crystalline phases in the different alloys investigated did not cause different electrochemical responses. However, the onset of secondary crystallization caused a reduction in the corrosion resistance in the NaCl media through a loss in passivating ability of all the alloys. This is due to increased galvanic activity as well as the loss of the amorphous phase.     

Evaluation of hydrogen absorption behaviour during acid etching for surface modification of commercial pure Ti, Ti-6Al-4V and Ni-Ti superelastic alloys

The hydrogen absorption behaviour during acid etching for the surface modification of commercial pure Ti, Ti-6Al-4V and Ni-Ti superelastic alloys has been investigated on the basis of the surface morphology, electrochemical behaviour and hydrogen thermal desorption analysis. To simulate the conventional acid etching for the improvement of the biocompatibility of Ti alloys, the specimens are immersed in 1 M HCl, 1 M H₂SO₄ or 0.5 M HCl + 0.5 M H₂SO₄ aqueous solution at 60 °C. Upon immersion, commercial pure Ti absorbs substantial amounts of hydrogen irrespective of the type of solution. In H₂SO₄ or HCl + H₂SO₄ solutions, the hydrogen absorption occurs for a short time (10 min). For Ti-6Al-4V alloy, no hydrogen absorption is observed in HCl solution, whereas hydrogen absorption occurs in other solutions. For Ni-Ti superelastic alloy, the amount of absorbed hydrogen is large, resulting in the pronounced degradation of the mechanical properties of the alloy even for an immersion time of 10 min, irrespective of the type of solution. The hydrogen absorption behaviour is not necessarily consistent with the morphologies of the surface subjected to corrosion and the shift of the corrosion potential. The hydrogen thermal desorption behaviour of commercial pure Ti and Ni-Ti superelastic alloy are sensitively changed by acid etching conditions. The present results suggest that the evaluation of hydrogen absorption is needed for each condition of acid etching, and that the conventional acid etching often leads to hydrogen embrittlement.     

Temperature effect in the corrosion resistance of Ni-Fe-Cr alloy in chloride medium

The corrosion susceptibility of alloy 33 in 0.5 mol/L sodium sulphate solutions containing or not 0.1 mol/L sodium chloride was tested at three different temperatures: 22 °C, 40 °C and 60 °C. Electrochemical studies were performed using corrosion potential measurements (E_corr) as well as potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Corrosion potential measurements showed that alloy 33 was passivated by a previously air formed film which was not destroyed during immersion in both solutions. No corrosion was observed during these tests although the temperature affected the film. Potentiodynamic polarization experiments showed that at high anodic potentials the previous film was broken up, and localized corrosion occurred in both solutions and at the three temperatures tested. Electrochemical impedance spectroscopy tests confirmed the presence of a stable passive film on the alloy surface at open circuit potential. Mott-Schottky analysis indicated that the passive film is an n-type semiconductor due to the presence of point defects of donor species, such as oxygen vacancies and interstitial metallic cations. As the potential increases the Cr(III) present in the barrier layer oxidizes producing Cr(VI) soluble species. The dissolution creates metallic cation vacancies that are acceptor species and the film changes from n-type to p-type semiconductor. The passive film rupture and the following localized attack are related to the drastic oxidative dissolution of the film at high anodic potentials, independent of its p-nature, chloride presence or increased temperature.     

Anodic oxidation and dielectric behaviour of aluminium-niobium alloys

The anodizing behaviour of sputtering-deposited Al-Nb alloys, containing 21, 31 and 44 at.% niobium, has been examined in 0.1 M ammonium pentaborate electrolyte with interest in the composition and the dielectric properties of the anodic oxides. RBS and TEM revealed amorphous oxides, containing units of Nb₂O₅ and Al₂O₃ in proportion to the alloy composition. Xenon marker experiments indicated their growth through migration of the Nb⁵⁺, Al³⁺ and O²⁻ species, with cation transport numbers, in the range 0.31-0.35, and formation ratios, in the range 1.35-1.64 nm V⁻¹, intermediate between those of anodic alumina and anodic niobia. Al³⁺ ions migrate slightly faster than Nb⁵⁺ ions, promoting a thin alumina layer at the film surface, although this layer is penetrated by fingers of the underlying niobium-containing oxide of relatively reduced ionic resistivity. The incorporation of units of Nb₂O₅ into anodic alumina increases the dielectric constant from about 9 to the range 11-22 for the investigated alloys.     

A newly synthesized glycine derivative to control uniform and pitting corrosion processes of Al induced by SCN anions - Chemical, electrochemical and morphological studies

A newly synthesized glycine derivative (termed GlyD), 2-(4-(dimethylamino)benzylamino)acetic acid hydrochloride, was used to inhibit uniform and pitting corrosion processes of Al in 0.50 M KSCN solutions (pH 6.8) at 25 °C. For uniform corrosion inhibition study, Tafel extrapolation, linear polarization resistance and impedance methods were used, complemented with SEM examinations. An independent method of chemical analysis, namely ICP-AES (inductively coupled plasma atomic emission spectrometry) was also used to test validity of corrosion rate measured by Tafel extrapolation method. GlyD inhibited uniform corrosion, even at low concentrations, reaching a value of inhibition efficiency up to 97% at a concentration of 5 × 10⁻³ M. Results obtained from the different corrosion evaluation techniques were in good agreement. This new synthesized glycine derivative was also used to control pit nucleation and growth on the pitted Al surface based on cyclic polarization, potentiostatic and galvanostatic measurements. The pitting potential (E_pit) and the repassivation potential (E_rp) increased by the addition of GlyD. Thus GlyD suppressed pit nucleation and propagation. Nucleation of pit was found to take place after an incubation time (t_i). The rate of pit nucleation and growth decreased with increase in inhibitor concentration. Morphology of pitting was also studied as a function of the applied anodic potential and solution temperature. Cross-sectional view of pitted surface revealed the formation of large distorted hemispherical and narrow deep pits. GlyD was much better than Gly in controlling uniform and pitting corrosion processes of Al in these solutions.     

Synergistic corrosion behavior of coated Ti60 alloys with NaCl deposit in moist air at elevated temperature

In the present paper, the corrosion behavior of Ti60 alloys with an aluminide, TiAlCr, and enamel coatings in moist air containing NaCl vapor at 700-800 °C were studied. The results showed that the TiAlCr and aluminide coatings failed to protect the substrate from corrosion due to the cyclic formation of volatile products during corrosion at 800 °C. However, an uneven continuous protective Al₂O₃ scale could form on the aluminide coating during corrosion at 700 °C. And the enamel coating could protect Ti60 from corrosion due to its high thermochemical stability and matched thermal expansion coefficient with substrates of Ti-base alloys during corrosion.     

Photocurrent spectroscopy applied to the characterization of passive films on sputter-deposited Ti-Zr alloys

A photoelectrochemical investigation on thin (?13 nm) mixed oxides grown on sputter-deposited Ti-Zr alloys of different composition by air exposure and by anodizing (formation voltage, U_F = 4 V/SCE) was carried out. The experimental results showed that the optical band gap, , increases with increasing Zr content in both air formed and anodic films. Such behaviour is in agreement with the theoretical expectation based on the correlation between the band gap values of oxides and the difference of electronegativity of their constituents. The flat band potential of the mixed oxides was found to be almost independent on the Ti/Zr ratio into the film and more anodic with respect to those estimated for oxide grown on pure Zr. The semiconducting or insulating character of the investigated films was strongly influenced by the forming conditions and the alloy composition.     

Corrosion behaviour of die-cast AZ91D magnesium alloy in aqueous sulphate solutions

The corrosion behaviour of die-cast AZ91D magnesium alloys in sulphate solutions was investigated by SEM, FTIR and polarization measurements. For immersion times less than 48 h, no pitting corrosion occurred and only generalized corrosion was apparent. According to the polarization curves, the corrosion rate order of the die-cast AZ91D Mg alloy in three aqueous solutions was: NaCl > MgSO₄ > Na₂SO₄. The main corrosion products were Mg(OH)₂ and MgAl₂(SO₄)₄·22H₂O in the sulphate solutions and the product film was compact. Precipitation of MgAl₂(SO₄)₄·22H₂O required a threshold immersion time.     

Corrosion protection of magnesium alloys by cerium, zirconium and niobium-based conversion coatings

A new Ce, Zr and Nb-based conversion coating was designed for AZ91 and AM50 magnesium alloys. The corrosion protection provided by this coating was evaluated by electrochemical measurements (polarization curves, electrochemical impedance spectroscopy) in Na₂SO₄ electrolyte, and accelerated atmospheric corrosion tests (humid, SO₂ polluted air, and salt spray). Its chemical composition was characterized by X-ray photoelectron spectroscopy (XPS). Electrochemical measurements showed that Mg alloys treated during 24 h in the Ce-Zr-Nb conversion bath exhibit: (i) increased corrosion potential, (ii) decreased corrosion and anodic dissolution current densities, and (iii) increased polarization and charge transfer resistances. The accelerated corrosion tests revealed excellent atmospheric corrosion resistance for all Ce-Zr-Nb-treated samples, with or without an additional layer of epoxy-polyamide resin lacquer or paint. XPS analysis showed that the coating includes CeO₂, Ce₂O₃, ZrO₂, Nb₂O₅, MgO, and MgF₂ as main components. No significant modification of the chemical composition was observed after cathodic and anodic polarization in Na₂SO₄. This new coating provides improved corrosion resistance, and excellent paint adhesion. It offers an alternative to the chromate conversion coating for magnesium alloys.     

Electrochemical stability of anodic titanium oxide films grown at potentials higher than 3 V in a simulated physiological solution

The cathodic behaviour of oxides formed on titanium electrodes in physiological solutions at potentials between 3 and 5 V (vs. SCE) was studied by cyclic voltammetry. In case of anodic polarization at potentials higher than 3 V (vs. SCE), a cathodic peak at ∼0.4 V (vs. SCE) appears in the cathodic scan, which could be due to the reduction of unstable peroxides. The results show that this peak depends on the anodic potential and the oxidation time. This behaviour supposedly is due to the formation of unstable titanium peroxides like TiO₃ during anodization. Based on repetitive oxidation-reduction processes can be concluded that the created amount of TiO₃ inside of the TiO₂ surface layer seems to be constant.     

2,2′-Dithiobis(3-cyano-4,6-dimethylpyridine): A new class of acid corrosion inhibitors for mild steel

The title compound (PyS)₂ has been synthesized and its inhibiting action on the corrosion of mild steel in 1-5 M H₂SO₄ solutions at 35-50 °C has been investigated by polarization resistance (R_p), polarization curves and electrochemical impedance spectroscopy (EIS). (PyS)₂ showed excellent performance and its efficiency did not affect either by increasing the acid concentration or rise of temperature. Polarization curves indicated that (PyS)₂ behaves mainly as anodic inhibitor in 1 M H₂SO₄ solutions and as a mixed-type inhibitor in 3 and 5 M H₂SO₄ solutions at different temperatures. Adsorption of (PyS)₂ on the steel surface followed Temkin’s adsorption isotherm with a very high negative value of the free energy of adsorption . The activation parameters of the corrosion process were calculated. EIS showed that the charge transfer controls the corrosion process in the uninhibited and inhibited solutions.     

Effect of underpotential deposition of lead on polarization behavior of nickel in acidic perchlorate solutions at room temperature

The effect of Pb²⁺ on polarization behavior of nickel has been investigated in 0.1 M NaClO₄ + 10⁻² M HClO₄ + x M PbO solutions (x = 0, 10⁻⁵, 10⁻⁴, 10⁻³) at room temperature. The cyclic voltammogram has suggested that Pb²⁺ degrades the stability of the passive film on Ni. The corrosion potential of Ni shifted to the more noble direction and the anodic current peak of Ni dissolution decreased with increasing Pb²⁺ concentration in solution, indicating that Pb²⁺ suppresses significantly the anodic dissolution. The underpotential deposition (UPD) of lead on Ni in the potential range more noble than −0.215 V (SHE) corresponding to the equilibrium potential of the Pb²⁺ (10⁻³ M)/Pb electrode was confirmed by XPS and GDOES analyses. The anodic Tafel slope, b⁺, of Ni dissolution changed from b⁺ = 40 mV decade⁻¹ in the absence of Pb²⁺ to b⁺ = 17 mV decade⁻¹ in the presence of 10⁻⁴ or 10⁻³ M Pb²⁺, which was ascribed to the increase in active sites of Ni surface emerged as a result of electrodesorption of Pb adatoms. The roles of Pb adatoms in active dissolution and active/passive transition of Ni were discussed from the above results.     

The initial stage of pitting corrosion on coated steels investigated by photon rupture in chloride containing solutions

A photon rupture method, film removal by a focused pulse of pulsed Nd-YAG laser beam irradiation, has been developed to enable oxide film stripping at extremely high rates without contamination from the film removal tools. In the present study, Zn-55mass%Al alloy and Al-9mass%Si alloy-coated steel specimens covered with protective nitrocellulose film were irradiated with a focused pulse of a pulsed Nd-YAG laser beam at a constant potential in 0.5 kmol m⁻³ H₃BO₃-0.05 kmol m⁻³ Na₂B₄O₇ (pH = 7.4) with 0.01 kmol m⁻³ of chloride ions to investigate the initial stage of localized corrosion. At low potentials, oxide films on both coated alloys were reformed after the nitrocellulose films were removed by this method. The oxide film formation kinetics follows an inverse logarithmic law, in agreement with Cabrera-Mott theory. However, at high potentials, localized corrosion producing corrosion products occurs at the area where nitrocellulose film was removed. Nevertheless, when the applied potential is less noble, the dissolution current of the Zn-55mass%Al-coated steel samples is higher than that of Al-9mass%Si-coated samples.     

The anodic dissolution of Mg in NaCl and Na2SO4 electrolytes by atomic emission spectroelectrochemistry

The dissolution of Mg has been investigated with atomic emission spectroelectrochemistry at open circuit and during potentiostatic control in chloride (NaCl) and sulfate (Na₂SO₄) electrolytes. A dissolution stoichiometry of approximately n = 2 is observed under all the conditions of these experiments with no evidence for the commonly invoked Mg⁺ intermediate. Nevertheless, in chloride electrolyte it is shown that anodic polarization results in a cathodic activation of the surface with increased hydrogen production during the polarization and an increased corrosion rate following the pulse. The formation of insoluble Mg oxides/hydroxides was also investigated in the sulfate electrolyte.     

Characterisation of anodic layers on Cu-10Sn bronze (RDE) in aerated NaCl solution

The anodic surfaces formed on Cu-10Sn (wt.%) alloy (α-bronze) are investigated in aerated 0.1 M aqueous chloride solution, using electrochemical reduction and characterisation methods such as scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). On the whole anodic domain, investigations performed on a bronze rotating disk electrode (RDE) reveal the systematic formation of a uniform oxidation layer. It is evidenced that the chemical composition of the layer varies with the applied anodic potential, but also that the latter always exhibits a poorly crystallised (probably nanocrystalline) hydrated and hydroxylated nature. Close to E_oc, the compounds are mainly (hydroxide) oxides of tin and copper, incorporating very low amounts of chlorides. At intermediate oxidation potentials corresponding to the active-passive transition, the first oxidation peak corresponds to the formation of hydrated tin oxyhydroxide chloride species which transforms in a more stable one - probably related to the Sn(II) → Sn(IV) oxidation. At higher anodic potential, on the current plateau, the layer contains hydrated tin (IV) oxyhydroxide and copper chloride (mainly CuCl). However, XRD and XPS results reveal that the barrier layer has a complex nature, including unidentified products and different spatially distributed charged surface zones. The corrosion mechanism involves an internal oxidation of the alloy linked to a preferential dissolution of copper, namely a decuprification. A decuprification factor f_Cu is defined and calculated. Both f_Cu and the layer thickness increase with the applied potential. We show unambiguously that the tin compounds remain in the corrosion layer, acting as stabilizing species. It is suggested that the tin species promote the formation of a network as for tin oxide xerogel, through which copper ions and anions migrate. Both the layer microstructure and the decuprification factor (f_Cu) are in agreement with those found in Type I patina of ancient bronzes.     

The corrosion behavior of Cu–Al and Cu–Al–Be shape-memory alloys in 0.5 M H2SO4 solution

The corrosion behavior of Cu–Al and Cu–Al–Be (0.55–1.0 wt%) shape-memory alloys in 0.5 M H₂SO₄ solution at 25 °C was studied by means of anodic polarization, cyclic voltammetry, and alternative current impedance measurements. The results of anodic polarization test show that anodic dissolution rates of alloys decreased slightly with increasing the concentrations of aluminum or beryllium. Severe intergranular corrosion of Cu–Al alloy was observed after alternative current impedance measurement performed at the anodic potential of 0.6 V. However, the addition of a small amount of beryllium was effective to prevent the intergranular corrosion. The effect of beryllium addition on the prevention of intergranular corrosion is possibly attributed to the diffusion of beryllium atoms into grain boundaries, which in turn deactivates the grain boundaries.     

Corrosion behaviour of 16%Cr-4%Al and 16%Cr ODS ferritic steels under different metallurgical conditions in a supercritical water environment

The corrosion behaviour of 16%Cr and 16%Cr-4%Al ODS ferritic steels in different heat treatment conditions has been investigated in a supercritical water environment. The exposed coupons were analyzed using scanning electron microscopy (SEM), electron probe micro analysis (EPMA), Auger and X-ray diffraction analysis (XRD). It was found that the formation of oxides depends on the chemical composition and not on the metallurgical condition. The Al-free alloys formed a monolayer oxide film composed of (Cr, Fe)₂O₃. The Al-containing alloys formed an oxide film composed of an outer layer of hematite and magnetite and an inner layer of Al₂O₃. The oxidation mechanisms are discussed.