Molten Salt Synthesis of Ba（ Mgl／3Nb2／3 ）O3 Powder

The single-phrase Ba(Mgl/3Nb2/3)O3(BMN) powder was saccessfully prepared by the KCImolten salt synthesis(MSS) method. The temperature for single-phase BMN powders by MSS was about 400℃ lower than that by the solid-phase method. The average particle size (APS) was about 0.91,u.m at 900℃ and increased with increasing synhesis temperature. Based on the APS, the activation energy for particle growth in theMSS, whose value was 64. 1kJmol^-1.was attained. The sinterability of the powder prepared by MSS method wasbetter than that pretared by solid-phase method.     

Preparation, Characterization and Dielectric Properties of Ba6Mg0.67Nb9.33O30 Ceramic

A new niobate Ba6Mg0.67Nb9.33O30 was ssnthesized in the BaO-MgO-Nb2O5 system by solid state reaction at 1350 ℃ for 48 b. The strncture and dielectric properties of Ba6Mg0.67Nb9.33O30 were determined by X-ray pouder diffraction, straining electron microscopy and dielectric measurements. The results show that Ba6Mg0.67Nb9.33O30 belongs to ferroelectric phase of filled tetragonal tungsten bronze structure at room temperature with unit cell parameters ： a = 1. 26052（4） nm , c = 0.40045（2） nm, space group P4bm , calculated density 5 . 707g. cm ^-3 . Ba6Mg0.67Nb9.33O30 belongs to relaxor ,ferroetectrics undergoing diffusive phase transition, and the transition temperature （ Tc ） is 30 ℃ observed at 10 kHz. At room temperature, Ba6Mg0.67Nb9.33O30 eeramic has a high dielectric constant 850 at 1 MHz and a low dielectric loss of 0. 0052.     

Electrochemical performance of nickel oxide／KOH／active carbon super-capacitor

The fabrication and characterization of new type Nickel oxide/KOH/Active carbon super-capacitor have been described. Porous nickel oxide was prepared by hydrolysis of nickel acetate and heated in air at 300℃. The resulting nickel oxide behaved as an electrochemical capacitor electrode with a specific capacitance (50-70 F/g) superior to most active carbon electrodes. This kind of nickel oxide maintained high utilization at high rate of discharge (i.e., high power density) and had excellent cycle life more than 1 000 times,while the capacitance of the cell composed of two identical nickel oxide electrodes was poor at high discharge current density and the maximum operational voltage of this type capacitor was limited to 0.5 V. A new type super-capacitor was designed in which the nickel oxide and the active carbon were applied to the positive and negative electrodes respectively. The breakdown voltage of this type super-capacitor was improved effectively to 0.8 V and excellent characteristic of high power discharge was attained in this way. The Nickel oxide/KOH/Active carbon super-capacitor has promising potentials in portable telecommunications, uninterruptable power supplies and battery load leveling applications.     

Experimental Crystallization of Synthetic V-bearing Steelmaking Slag with Al2O3 Doped

The phenomenon of crystallization was implemented in the synthetic V-bearing steelwork slag based on the composition of factory slag from the Masted Co., and the possibility of undercooling as a technique to precipitate V-concentration phase was demonstrated. The effect of 20wt% Al2O3 additive introduced into the slag on intensifing the precipitation was also investigated. X-ray diffraction analysis ( XRD ) and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX) were used to investigate the slag after heat treatment. It is demonstrated that gehleaite and grossite are the major crystalline phases. Whitlockite with a high content of V2O5 ( called V-concentration phase hereafter) nucleates homogeneously and hetergeneously and grows with decreasing undercooling. At 1548 K, the crystals of V-concentration phase grow up as the duration of time, with a medium grain size of 25μm at 300 rain holding time.     

Effect of magnesium addition on inclusions in H13 die steel

The effect of magnesium addition on the number, morphology, composition, size, and density of inclusions in H13 die steel was studied. The results show that the total oxygen content in the steel can be significantly decreased to 0.0008wt%. Al2O3 and Mn S inclusions are changed into nearly spherical Mg O·Al2O3 spinel and spherical Mg O·Mg S inclusions, respectively. The number of inclusions larger than 1 μm decreases and the number of inclusions smaller than 1 μm increases with increasing magnesium content. V（N,C） precipitates around Mg O·Al2O3 and Mg O·Mg S inclusions during solidification of liquid steel. The densities of Mg O·Al2O3 spinel inclusions are lower than that of alumina inclusions. With increasing magnesium content in the Mg-containing inclusions, the density of inclusions decreases, leading to the improvement of inclusion removal efficiency.     

Formation mechanism and control of MgO·Al2O3 inclusions in non-oriented silicon steel

On the basis of the practical production of non-oriented silicon steel, the formation of Mg O·Al2O3 inclusions was analyzed in the process of ＂basic oxygen furnace（BOF） → RH → compact strip production（CSP）＂. The thermodynamic and kinetic conditions of the formation of Mg O·Al2O3 inclusions were discussed, and the behavior of slag entrapment in molten steel during RH refining was simulated by computational fluid dynamics（CFD） software. The results showed that the Mg O/Al2O3 mass ratio was in the range from 0.005 to 0.017 and that Mg O·Al2O3 inclusions were not observed before the RH refining process. In contrast, the Mg O/Al2O3 mass ratio was in the range from 0.30 to 0.50, and the percentage of Mg O·Al2O3 spinel inclusions reached 58.4% of the total inclusions after the RH refining process. The compositions of the slag were similar to those of the inclusions; furthermore, the critical velocity of slag entrapment was calculated to be 0.45 m·s^-1 at an argon flow rate of 698 L·min^-1, as simulated using CFD software. When the test steel was in equilibrium with the slag, [Mg] was 0.00024wt%–0.00028wt% and [Al]s was 0.31wt%–0.37wt%; these concentrations were theoretically calculated to fall within the Mg O·Al2O3formation zone, thereby leading to the formation of Mg O·Al2O3 inclusions in the steel. Thus, the formation of Mg O·Al2O3 inclusions would be inhibited by reducing the quantity of slag entrapment, controlling the roughing slag during casting, and controlling the composition of the slag and the Mg O content in the ladle refractory.     

Preparation, Characterization and Dielectric Property of Sr5 LaTi3 Nb7O30 Ceramic

Sr5LaTi3Nb7O30 ceramic was prepared by the conventional high temperature solid-state reaction route. The sintered samples were characterized by X-ray diffraction, scanning electron microscopy ( SEM ), differential thermal calorimetry ( DSC ) and dielectric measurements. The results show Sr5LaTi3Nb7O30 belongs to paraclectric phase of filled tetrngonal TB structure at room temperature, and undergoes a diffuse phase transition in the temperature range of -54-34℃ . And Sr5LaTi3Nb7O30 ceramic shows a high dielectric constant of 479 with a low dielectric loss of 0.005 at 1MHz . In comparison with Ba-based ceramics with TB structure, the temperature coefficients of the dielectric constant ( τt ) is significantly reduced.     

Pressureless infiltration of Si3N4 preforms with an Al-2wt%Mg alloy

The pressureless infiltration process to synthesize a silicon nitride composite was investigated. An Al-2wt%Mg alloy was infiltrated into silicon nitride preforms in the atmosphere of nitrogen. It is possible to infiltrate the Al-2wt%Mg alloy in silicon nitride preforms, The growth of the composite with useful thickness was facilitated by the presence of magnesium powder at the interface and by flowing nitrogen. The microstructure of the Si3N4-Al composite has been characterized using scanning electron microscope. During the infiltration of Si3N4 preforms, Si3N4 reacted with aluminium to form silicon and AIN. The silicon produced during the growth consumed in the formation of MgSiAIO, MgSiAlN and Al3.27Si0.47 type phases. The growth of the composite was found to proceed in two ways, depending on the oxide content in the initial preforms, First, less oxide content preforms gave rise to MgAlSiO and MgAlSiN type phases after infiltration. Second, more oxide content preforms gave rise to AlN-Al2O3 solid solution phase （AlON）, The AlON phase was only present in the composite, containing 10% aluminium in the silicon nitride preforms before infiltration.     

Preparation, characterization and photocatalytic behavior of WO3-TiO2/Nb2O5 catalysts

TiO2/Nb2O5 photocatalyst loaded with WO3 (WO3-TiO2/Nb2O5) was prepared by a modified hydrolysis process, and characterized by X-ray diffractometry, transmission electron microscopy, Raman spectra and UV-Vis diffuse refraction spectroscopy. The photocatalytic activity of WO3-TiO2/Nb2O5 was investigated by employing splitting of water for O2 evolution. The results indicate that WO3 loading can pronouncedly improve the photocatalytic activity of TiO2/Nb2O5 by using Fe3 as an electron acceptor under UV irradiation. The optimum molar fraction of the loaded WO3 is 2%, and the largest speed of O2 evolution for 2% WO3-TiO2/Nb2O5 catalyst is 151.8 μmol/(L·h).     

Influence of Cr2O3-Al2O3 composite oxide scale on oxidation resistance of ZG40Cr24

Test alloys ZG40Cr24 with alloying of 3 wt% aluminium were cast by intermediate frequency induction furnace. The oxidation resistance of test alloys at 1 000 ℃ for 500 hours was examined according to oxidation weight gain method. The scale morphology and composition were studied using scanning electron microscope (SEM) and X-ray diffraction (XRD) respectively. By energy dispersive spectroscopy (EDS) studies, a kind of composite oxide scale compounded highly by Cr2O3, Al2O3 and spinel MCr2O4 in molecule scale came into being at high temperature. With flat and compact structure, fine and even grains, such composite scale granted complete oxidation resistance to alloy ZG40Cr24. The oxidation resistance mechanism was studied deeply in electrochemistry corrosion. The P+N semiconductor composite scale composed plenty of inner PN junctions, of which the unilateral conductive and the out-of-order arrangement endowed itself insulating in all directions. The positive and negative charges in scale could not move, and the mobile number and transferring rate of them both dropped enormously, as a result, the oxidation rate of the matrix metal was cut down greatly. So the composite scale presented excellent oxidation resistance.     

Y3+取代Bi3+对Bi2(Zn1/3Nb2/3)2O7陶瓷烧结温度的影响

采用固相反应制备Bi2(Zn1/3Nb2/3)2O7微波陶瓷,并借助X射线、扫描电镜、LCR4284测试仪,研究Y3 取代Bi3 对Bi2(Zn1/3Nb2/3)2O7陶瓷烧结特性及介电性能的影响。研究结果表明:随着Y3 替代量的增加,晶粒尺寸减小,介电常数先减小后增大,烧结温度升高;适量的Y3 替代可以获得性能很好的BZN介质材料。     

白云鄂博铌精矿碳还原直接合金化热力学研究

本文针对使用铌精矿代替铌铁合金在精炼炉的环境下进行直接合金化炼钢的过程,使用FactSage软件进行还原剂为C时,不同Nb2O5活度系数、温度、碱度、渣成分下[Nb]/Nb2O5值进行热力学平衡计算.综合分析结果表明,Nb2O5活度系数成为影响其还原进入钢液的重要因素之一;C作为还原剂时的有利条件为高温、低碱度、低（FeO）;（TiO2）对于[Nb]/Nb2O5的影响较小.使用《矿物炼钢》中类似体系的共存模型结果计算了C还原Nb2O5反应的吉布斯自由能随温度和碱度的变化.结果表明C还原Nb2O5反应的AG随碱度升高而增大,随温度的升高而降低.LNb随碱度升高而降低,随温度的升高而升高.     

介孔分子筛Nb2O5/SBA-15催化合成油酸甲酯

以介孔分子筛SBA-15为载体,采用浸渍法合成了Nb2O5/SBA-15催化剂。通过XRD、BET等测试手段对样品进行了分析。结果表明,负载Nb2O5的SBA-15分子筛具有高度有序的二维六方介孔结构,并且具有较大的比表面积、孔容和孔径。Nb2O5/SBA-15分子筛催化剂的酯化反应最佳反应条件为：醇酸物质的量比为2∶1,反应温度160 ℃ ,反应时间4 h,催化剂用量为原料总质量的9.10%。Nb2O5/SBA-15催化剂具有较好的稳定使用性,是一种合成油酸甲酯的理想固体酸催化剂。     

(K1-xNax)（Ta（1-y）Nby）O3纳米粉体的水热合成研究

采用水热法合成了不同组分的无铅压电(K1-xNax)(Ta1-yNby)O3(KNTN)纳米粉体。研究结果表明,在高介质碱度条件下可以获得K/Na摩尔比为1的KNTN纳米粉体。随着K含量的增加,产物由单斜向四方晶型转变。产物中的Ta/Nb摩尔比与原料中Ta2O5/Nb2O5摩尔比呈线性关系。随着Ta含量的增加,KNTN由正交→四方→立方晶型转变,其微结构则由长方体逐渐转变为立方体结构。     

铌钴共掺杂钛酸钡陶瓷的介电温度稳定性的研究

采用X射线衍射(XRD)、拉曼光谱(RS)、原子力显微镜(AFM)以及介电温谱(DTC)研究BaTiO3-xNb2O5-0.005Co2O3(x=0.02,0.04,0.08)系统中Nb含量变化对陶瓷的结构及介电温度稳定性的影响.结果表明:增加Nb含量将增强介电陶瓷的温度稳定性,但介电常数降低.Nb含量在4%以上时NC陶瓷满足X7R介电指标.     

LiNbO3/Al2O3复合材料的制备及其力学性能

为了研究铁电相LiNbO3对Al2O3陶瓷材料结构及其力学性能的影响,以Al2O3 Nb2O5 和LiCO3为主要原料,分别通过高温固相法和热压烧结法,制备LiNbO3/Al2O3复合材料.对制备的复合材料进行物相分析,抗折强度的测试以及显微形貌观察.结果发现：LiNbO3的加入有利于促进Al2O3的烧结,降低了Al2O3陶瓷的烧结温度.当烧结温度超过1 200℃时,复合材料的主晶相仍然为LiNbO3和Al2O3,但由于少量Li元素挥发,生成物相LiNb3O8.在1 200℃保温3h,通过高温固相法烧结,5vol％ LiNbO3/95vol％ Al2O3复合材料的抗弯强度达到了最高,为162.34MPa.在1 300℃,150MPa（保温保压1h）热压烧结制备的15 vol％ LiNbO3/85 vol％ Al2O3复合材料致密度为92.82％,其抗弯强度和断裂韧性分别为393.94 MPa和2.38 MPa· m1/2.该复合材料中的LiNbO3晶粒出现了非180°畴结构,这种电畴结构有利于改善材料的力学性能.     

Comparative experiment on layered Li（Ni1/3Co1/3Mn1/3）O2 as the alternative material for LiCoO2

This work was financially supported by the National Natural Science Foundation of China （No.50472093）.     

Eu3+浓度对Ca3Al2O6:Eu3+晶体结构和发光性能的影响

以β-丙氨酸和尿素为燃料,采用溶液燃烧法在低温450℃下合成制备了Ca3Al2O6:Eu3+荧光粉。样品的发射光谱由位于594 nm、617 nm、653 nm及700 nm处的4组线状峰构成,分别对应Eu3+的5D0→7Fj(j=1~4)特征跃迁,其中617 nm处的峰最强,样品呈现红色发光。考察了Eu3+掺杂浓度对晶体结构和发光性能的影响。结果呈示:随着掺杂浓度的增加晶格常数逐渐减小,[O—Al—O]的对称伸缩振动Raman峰蓝移;在低掺杂浓度时荧光强度逐渐增大,掺杂6%时达到最大,之后出现浓度猝灭现象,猝灭机制为交互作用;Eu3+的5D0→7F2与5D0→7F1跃迁强度比随着掺杂浓度的增加逐渐增大,掺杂的Eu3+主要取代处于非对称中心的Ca2+。     

NiO／A12O3的制备及其在羊毛脂加氢中的应用

以硝酸镍和氧化铝为前驱物,氢氧化钠为沉淀剂,采用共沉淀法制备负载型催化剂NiO／A12O3并将所制得的催化剂应用于羊毛脂加氢反应中。通过测定加氢产物的皂化值考察了催化剂质量分数、氢气压强、反应时间、反应温度等条件对羊毛脂加氢深度的影响。实验结果表明,在反应时间5h、反应温度300℃、氢气压强18MPa、催化剂质量分数5％的条件下,羊毛脂的加氢深度可达到93．47％。