The corrosion inhibition of copper in hydrochloric acid solutions by a tripeptide compound

The efficiency of glutathione as a non-toxic corrosion inhibitor for copper in 0.5 M HCl has been studied by using the weight-loss technique, cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization. Maximum protection efficiency reaches about 92.7% for glutathione at 10 mM concentration level. Results obtained from potentiodynamic polarization and impedance measurements are in good agreement. The adsorption of glutathione on copper surface follows Langmuir isotherm. The adsorption free energy of glutathione on copper (−32 kJ mol⁻¹) reveals a strong physical adsorption of the inhibition on the metal surface.     

Synergistic inhibition effect of rare earth cerium(IV) ion and sodium oleate on the corrosion of cold rolled steel in phosphoric acid solution

The synergistic inhibition effect of rare earth cerium(IV) ion (Ce⁴⁺) and sodium oleate (SO) on the corrosion of cold rolled steel (CRS) in 3.0 M phosphoric acid (H₃PO₄) has been investigated by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) and scanning electron microscope (SEM) methods. The results reveal that SO has a moderate inhibitive effect and its adsorption obeys Temkin adsorption isotherm. Ce⁴⁺ has a poor effect. However, incorporation of Ce⁴⁺ with SO improves the inhibition performance significantly, and exhibits synergistic inhibition effect. SO acts as a cathodic inhibitor, while SO/Ce⁴⁺ mixture acts as a mixed-type inhibitor.     

Investigation of the inhibition effect of indole-3-carboxylic acid on the copper corrosion in 0.5 M H2SO4

Inhibition of the copper corrosion by means of indole-3-carboxylic acid (ICA), was studied in 0.5 M H₂SO₄ solutions in the temperature range from 25 °C to 55 °C using potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. The results obtained from the both measurement techniques revealed good inhibitor efficiency in the studied concentration range. Nyquist plots showed depressed semicircles with their centre below real axis. Moreover, the impedance spectra in the case of both non inhibited solutions and inhibited ones by means of lower inhibitor concentrations exhibited Warburg impedance. The adsorption behaviour of ICA followed Langmuir’s isotherm.     

Inhibitory effect of some amino acids on corrosion of Pb-Ca-Sn alloy in sulfuric acid solution

The present article describes the inhibition effect of amino acids cysteine (Cys), methionine (Met) and alanine (Ala), towards the corrosion of lead-alloy (Pb-Ca-Sn) in H₂SO₄ solution by potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), weight loss measurement and scanning electron microscopy (SEM) methods. The influence of inhibitor concentration, temperature and time on inhibitory behavior of the amino acids was investigated. The corrosion data including corrosion current density (I_corr), corrosion potential (E_corr) and charge transfer resistance (R_ct) were determined from Tafel plots and EIS. Recording impedance spectra showed that the charge transfer resistance is increased by increasing adsorption time. The SEM micrographs revealed that the corroded surface area is decreased in the presence of amino acids. Meanwhile, the inhibition efficiency (IE) was found to be depending on the type of amino acid and its concentration. The IE for 0.1 M Cys in 0.5 M H₂SO₄ is greater than 96%. Adsorption isotherms were fitted by Langmuir isotherm.     

Synergistic inhibition effect of 6-benzylaminopurine and iodide ion on the corrosion of cold rolled steel in H3PO4 solution

The synergistic inhibition effect of 6-benzylaminopurine (BAP) and iodide ion (I⁻) on the corrosion of cold rolled steel (CRS) in 1.0 M H₃PO₄ solution was studied by weight loss, potentiodynamic polarization curves and electrochemical impedance spectroscopy (EIS) methods. The results show that BAP has a moderate inhibitive effect. However, incorporation of BAP with I⁻ improves the inhibition performance significantly. The adsorption of BAP in the absence and presence of I⁻ obeys Langmuir adsorption isotherm. BAP and BAP/I⁻ mixture act as mixed-type inhibitors. A probable synergism mechanism is proposed.     

Effect of serine, threonine and glutamic acid on the corrosion of copper in aerated hydrochloric acid solution

The corrosion inhibition of three amino acid compounds on copper was investigated by electrochemical method. They suppressed cathodic current densities and shifted the corrosion potential towards more negative values. The interaction between amino acid and copper surface was certified by reflected FT-infrared spectroscopy. The quantum chemical parameters were obtained by PM3 semi-empirical calculation. Glutamic acid has the smaller net positive charge of nitrogen atom and the more net negative charge of oxygen atoms. The improved inhibition of glutamic acid was due to the stabilization of its adsorption on the copper surface by the oxygen atoms in its structure.     

Inhibition effects of 2,5-dimercapto-1,3,4-thiadiazole on the corrosion of mild steel in sulphuric acid solution

The effect of 2,5-dimercapto-1,3,4-thiadiazole (DMTD) on the corrosion of mild steel (MS) in 1.0 M H₂SO₄ was investigated. DMTD acted as a mixed-type inhibitor without change of the mechanism of hydrogen evolution. The inhibition efficiency increased with the increase in concentration of DMTD but decreased with the increase of temperature. Adsorption of the inhibitor on the MS surface obeyed the Langmuir adsorption isotherm. The potential of zero charge suggests MS surface is positively charged in 1.0 M H₂SO₄. Thermodynamics and quantum chemical calculations reveal that the adsorption process of DMTD includes electrostatic interaction and electron donor–acceptor interactions.     

Carbon steel corrosion inhibition in hydrochloric acid solution using a reduced Schiff base of ethylenediamine

The behavior of the Schiff base N,N′-bis(salicylidene)-1,2-ethylenediamine (Salen), its reduced form (N,N′-bis(2-hydroxybenzyl)-1,2-ethylenediamine) and a mixture of its preceding molecules, ethylenediamine and salicylaldehyde, as carbon steel corrosion inhibitors in 1 mol L⁻¹ HCl solution was studied by corrosion potential measurements, potentiodynamic polarization curves, electrochemical impedance spectroscopy and spectrophotometry measurements. The experimental results showed that the reduced Salen presented the highest efficiency among the inhibitors studied. The results obtained in the presence of Salen were similar to those obtained in the presence of the salicylaldehyde and ethylenediamine mixture, showing that in acid medium the Salen molecule undergoes hydrolysis, regenerating its precursor molecules.     

Experimental and theoretical studies of thiazoles as corrosion inhibitors for mild steel in sulphuric acid solution

The inhibition effects of 2-amino-5-mercapto-1,3,4-thiadiazole (2A5MT) and 2-mercaptothiazoline (2MT) on mild steel corrosion in 1.0 M H₂SO₄ were studied with potentiodynamic polarization, linear polarization resistance and electrochemical impedance spectroscopy techniques. It was shown that both 2A5MT and 2MT act as good corrosion inhibitors for mild steel protection. The high inhibition efficiencies were attributed to the simple blocking effect by adsorption of inhibitor molecules on the steel surface. The effects of the presence of extra NH₂ group and N atom in 2A5MT on the ability to act as corrosion inhibitors were investigated by theoretical calculations.     

Inhibition effect of methyl violet on the corrosion of cold rolled steel in 1.0 M HCl solution

The inhibition effect of methyl violet (MV) on the corrosion of cold rolled steel (CRS) in 1.0 M HCl solution at 20-50 °C was studied by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) methods. The results show that MV is an excellent inhibitor even with very low concentration, and the adsorption of MV on CRS surface obeys Langmuir adsorption isotherm. Potentiodynamic polarization curves reveal that MV behaves as a mixed-type inhibitor. EIS spectra exhibit one capacitive loop and confirm the inhibitive ability. The inhibition action of MV is also evidenced by SEM.     

Ultrafine-grained copper produced by machining and its unusual electrochemical corrosion resistance in acidic chloride pickling solutions

Ultrafine-grained (UFG) copper was prepared by facile machining procedure. High resolution transmission electron microscopy images revealed that, in UFG Cu, minimum grain size of 80 nm could be formed when a small machining rake angle was applied. The electrochemical corrosion behavior of UFG Cu in 0.5 M HCl was investigated by potentiodynamic polarization and electrochemical impedance spectroscopy. Comparing with coarse-grained Cu, UFG Cu exhibited notably declined corrosion current density. Particularly, when the size of Cu grains were reduced from 500 μm to 80 nm, the charge transfer resistance of anodic dissolution step dramatically increased from 200 to 621 Ω cm².     

Blue tetrazolium as a novel corrosion inhibitor for cold rolled steel in hydrochloric acid solution

The inhibition effect of blue tetrazolium (BT) on the corrosion of cold rolled steel (CRS) in 1.0 M HCl solution at 20 °C was investigated by weight loss, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM) methods. The results show that BT is a very good inhibitor, and the adsorption of BT on CRS surface obeys Langmuir adsorption isotherm. Polarization curves reveal that BT acts as a mixed-type inhibitor. EIS spectra exhibit one capacitive loop and confirm the inhibitive ability. The inhibition action of BT is also evidenced by SEM images.     

Synergistic effect of potassium iodide with phthalazone on the corrosion inhibition of mild steel in 1.0 M HCl

The effects of phthalazone (PTO) and its synergistic effect with KI on the corrosion of mild steel in 1.0 M HCl solution were studied using electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization measurements. The inhibition efficiency increases with the concentration of the inhibitor and increased further with the presence of 6.02 mM KI. The synergistic effect of 6.02 mM KI at different concentrations of PTO was determined by calculating the synergism parameters, which showed that a cooperative mechanism exists between the iodide anion and PTO cations.     

A study of the inhibition of iron corrosion in HCl solutions by some amino acids

The performance of three selected amino acids, namely alanine (Ala), cysteine (Cys) and S-methyl cysteine (S-MCys) as safe corrosion inhibitors for iron in aerated stagnant 1.0 M HCl solutions was evaluated by Tafel polarization and impedance measurements. Results indicate that Ala acts mainly as a cathodic inhibitor, while Cys and S-MCys function as mixed-type inhibitors. Cys, which contains a mercapto group in its molecular structure, was the most effective among the inhibitors tested, while Ala was less effective than S-MCys. The low inhibition efficiency recorded for S-MCys compared with that of Cys was attributed to steric effects caused by the substituent methyl on the mercapto group. Electrochemical frequency modulation (EFM) technique and inductively coupled plasma atomic emission spectrometry (ICP-AES), were also applied to make accurate determination of corrosion rates. Validation of the Tafel extrapolation method for measuring corrosion rates was tested. Rates of corrosion rates (in μm y⁻¹) obtained from Tafel extrapolation method are in good agreement with those measured using EFM and ICP methods. Some theoretical studies, including molecular dynamics (MD) and density functional theory (DFT), were also employed to establish the correlation between the structure (molecular and electronic) of the three tested inhibitors and the inhibition efficiency. Adsorption via hydrogen bonding was discussed here based on some theoretical studies. Experimental and theoretical results were in good agreement.     

Electrochemical investigation and modeling of corrosion inhibition of aluminum in molar nitric acid using some sulphur-containing amines

Chemical and electrochemical measurements incorporated with quantum chemical calculations and molecular dynamics simulations were used to study the corrosion inhibition characteristics of some thiosemicarbazone derivatives on the inhibition of aluminum corrosion in 1.0 M HNO₃. Polarization curves demonstrated that the thiosemicarbazone derivatives were of mixed-type inhibitors. EIS plots indicated that the addition of thiosemicarbazone derivatives increases the charge-transfer resistance of the corrosion process, and hence the inhibition performance. The molecular dynamics simulation results show that the three thiosemicarbazone derivatives can adsorb on the A₂O₃ (1 1 1) surface through the sulphur and nitrogen atoms as well as π-electrons in the pyridyl structure.     

The influence of pH value on the efficiency of imidazole based corrosion inhibitors of copper

The aim of this work is to establish the correlation between the solution pH and the inhibiting efficiency of two imidazole compounds (4-methyl-1-phenyl imidazole and 4-methyl-1-(p-tolyl) imidazole) in protection of copper from corrosion in chloride media.It was found that the inhibiting efficiency of both studied imidazoles enhances with the increase of the solution pH value, from about 20% in 0.5 M HCl to 92% in 0.5 M NaCl. This improvement was ascribed to stronger adsorption of neutral imidazole molecule, which can be expected at higher pH values, than that of the protonated imidazole cation, which may be expected in acid solutions.     

EN, EIS and polarization studies to evaluate the inhibition effect of 3H-phenothiazin-3-one, 7-dimethylamin on mild steel corrosion in 1 M HCl solution

The corrosion inhibition effect of 3H-phenothiazin-3-one, 7-dimethylamin as a new inhibitor was studied using different electrochemical and weight loss methods. It was found that this compound acts as a strong inhibitor for mild steel in 1 M HCl even at very low concentration (1 ppm). Results showed that this compound acts as a mixed type inhibitor. As the inhibitor concentration increased, the charge transfer resistance of mild steel increased and double layer capacitance decreased. The results of EN measurements after trend removal were in good agreement with other methods results. It was found that this inhibitor acts through adsorption on the metal surface. Also, adsorption obeys the Langmuir isotherm.     

A comparative study of the corrosion inhibition of mild steel in sulphuric acid by 4,4-dimethyloxazolidine-2-thione

The corrosion protection of mild steel in a 2.5 M H₂SO₄ solution by 4,4-dimethyloxazolidine-2-thione (DMT) was studied at different temperatures by measuring changes in open circuit potential (OCP), potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS). Corrosion current densities calculated from EIS data were comparable to those obtained from polarisation measurements. Results showed that DMT inhibited mild steel corrosion in a 2.5 M H₂SO₄ solution and indicated that the inhibition efficiencies increased with the concentration of inhibitor, but decreased proportionally with temperature. Polarisation curves showed that DMT is a mixed-type inhibitor. Changes in impedance parameters suggested the adsorption of DMT on the mild steel surface, leading to the formation of protective films. The DMT adsorption on the mild steel surface followed the Langmuir adsorption isotherm. The kinetic and thermodynamic parameters for dissolution and adsorption were investigated. Comprehensive adsorption (physisorption and chemisorption) of the inhibitor molecules on the mild steel surface was suggested based on the thermodynamic adsorption parameters.     

Copper corrosion inhibition in O2-saturated H2SO4 solutions

Corrosion inhibition of copper in O₂-saturated 0.50 M H₂SO₄ solutions by four selected amino acids, namely glycine (Gly), alanine (Ala), valine (Val), or tyrosine (Tyr), was studied using Tafel polarization, linear polarization, impedance, and electrochemical frequency modulation (EFM) at 30 °C. Protection efficiencies of almost 98% and 91% were obtained with 50 mM Tyr and Gly, respectively. On the other hand, Ala and Val reached only about 75%. Corrosion rates determined by the Tafel extrapolation method were in good agreement with those obtained by EFM and an independent chemical (i.e., non-electrochemical) method. The chemical method of confirmation of the corrosion rates involved determination of the dissolved Cu²⁺, using ICP-AES (inductively coupled plasma atomic emission spectrometry) method of chemical analysis. Nyquist plots exhibited a high frequency depressed semicircle followed by a straight line portion (Warburg diffusion tail) in the low-frequency region. The impedance data were interpreted according to two suitable equivalent circuits. The kinetics of dissolved O₂ reduction and hydrogen evolution reactions on copper surface were also studied in O₂-saturated 0.50 M H₂SO₄ solutions using polarization measurements combined with the rotating disc electrode (RDE). The Koutecky-Levich plot indicated that the dissolved O₂ reduction at the copper electrode was an apparent 4-electron process.     

The effect of ionic liquids with imidazolium and pyridinium cations on the corrosion inhibition of mild steel in acidic environment

Ionic liquids with chemical formula 1,3-dioctadecylimidazolium bromide and N-Octadecylpyridinium bromide were synthesized by conventional and microwave-assisted reactions, respectively. Ionic liquids tested as corrosion inhibitors after polarization curves displayed corrosion protection efficiency within 82-88% at 100 ppm for mild steel in a 1 M aqueous solution of sulfuric acid. Standard free energy indicated that corrosion inhibition occurred by a chemical adsorption process. Surface analysis (SEM, EDX) completed by XRD and Mössbauer spectroscopy indicated the presence of carbon species pertaining to inhibitor and corrosion products, which was rationalized in an inhibition mechanism.