Electrochemical behaviour of Ni-base alloys exposed under oil/gas field environments

The electrochemical behaviour of Ni-base alloys (Inconel 625, Inconel 718, G3 and Incoloy 825) is carried out at 80 °C in CO₂/H₂S corrosion environments using cyclic potentiodynamic polarisation and electrochemical impedance spectroscopy (EIS) techniques. The passivity mechanisms are analysed and discussed. In addition, some significant characterisation parameters such as E_corr, I_pass, E_pit, E_pp, ΔE and I_pass in cyclic polarisation curves are analysed and compared to reveal the corrosion resistance of various Ni-base alloys. The equivalent circuit model and ZsimpWin software are utilised to discuss the Nyquist plots of various Ni-base alloys. The diffusion mechanism in EIS measurement is discussed. The result shows that the corrosion resistance of the Ni-base alloys to CO₂ corrosion or CO₂/H₂S corrosion follows the sequence: Inconel 625 > G3 > Inconel 718 > Incoloy 825. H₂S works as a cathodic depolariser with accelerating initiation of the corrosion process.     

Effect of surface finishing of a Zr-based bulk metallic glass on its corrosion behaviour

Zr-based metallic glasses passivate spontaneously, but exhibit also a certain pitting susceptibility. On the example of the Zr₅₉Ti₃Cu₂₀Al₁₀Ni₈ alloy studied in 0.01 M Na₂SO₄ + x M NaCl (x = 0-0.1) electrolytes it is demonstrated that the surface finishing state and the pre-exposure conditions can significantly influence the free corrosion and anodic polarisation behaviour. Mechanical fine-polishing procedures can lead to extremely smooth topographies but also to Cu enrichment at the surface. This yields a pronounced Cu dissolution at low anodic polarisation prior to stable passivity and increases the pitting initiation susceptibility as compared to mechanically ground surface states.     

Oxide properties and stress corrosion cracking behaviour for Alloy 600 in leaded caustic solutions at high temperature

The stress corrosion cracking behaviour of Alloy 600 in caustic solutions with and without PbO at 315 °C was investigated by means of slow strain rate tension tests. The characterisation of the oxide that formed on Alloy 600 was derived from transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. Lead was incorporated into the oxide in a metallic lead state and a lead oxide state, which degraded the passivity and induced PbSCC susceptibility. NiB was used as an inhibitor. It reduced the lead incorporation level in the oxide layer and decreased PbSCC susceptibility.     

Comparison of the corrosion behaviour of bulk and thin film magnesium alloys

The corrosion behaviour of bulk and thin film specimens consisting of commercial magnesium alloys AZ31 and AZ80 was investigated by electrochemical tests in 3.5 wt.% NaCl solution and in phosphate buffered saline solution (PBS) at room temperature. Corrosion tests indicated that the corrosion rates are nearly equal, but localized attack was more pronounced for the bulk specimens than for the thin film samples. XRD analyses showed that this behaviour can be attributed to the fact that the as-deposited thin film specimens do not contain any precipitates, which are present in the bulk samples and are considered to enhance localized corrosion.     

Effect of excimer laser surface melting on the microstructure and corrosion performance of the die cast AZ91D magnesium alloy

Excimer laser surface melting (LSM) of the die cast AZ91D alloy has been investigated in terms of microstructure and corrosion behaviour. Excimer LSM of the alloy resulted in a highly homogeneous and refined melted microstructure, which improved the corrosion resistance of the alloy. The latter was associated with the large dissolution of intermetallic phases and the enrichment of aluminium within the melted layer. An increased number of laser pulses resulted in thicker melted layers, but also in enhanced porosity and the formation of micro-cracks at the overlapping area. Both factors diminished the corrosion resistance of the laser-treated alloy.     

Passivation and corrosion behaviours of cobalt and cobalt-chromium-molybdenum alloy

Passivation and corrosion behaviour of the cobalt and cobalt-base alloy Co30Cr6Mo was studied in a simulated physiological solution containing chloride and bicarbonate ions and with pH of 6.8. The oxido-reduction processes included solid state transformations occurring at the cobalt/electrolyte interface are interpreted using theories of surface electrochemistry. The dissolution of cobalt is significantly suppressed by alloying it with chromium and molybdenum, since the alloy exhibited “chromium like” passivity. The structural and protective properties of passive oxide films formed spontaneously at the open circuit potential or during the anodic polarization were studied using electrochemical impedance spectroscopy in the wide frequency range.     

Effect of the aluminium content of AlxCrFe1.5MnNi0.5 high-entropy alloys on the corrosion behaviour in aqueous environments

High-entropy alloys (HEAs) are a newly developed family of multi-component alloys. The potentiodynamic polarization and electrochemical impedance spectroscopy of the Al_xCrFe_1.5MnNi_0.5 alloys, obtained in H₂SO₄ and NaCl solutions, clearly revealed that the corrosion resistance increases as the concentration of aluminium decreases. The Al_xCrFe_1.5MnNi_0.5 alloys exhibited a wide passive region, which extended >1000 mV in acidic environments. The Nyquist plots of the Al-containing alloys had two capacitive loops, which represented the electrical double layer and the adsorptive layer. SEM micrographs revealed that the general and pitting corrosion susceptibility of the HEAs increased as the amount of aluminium in the alloy increased.     

Influence of temperature and applied potential on the electrochemical behaviour of nickel in LiBr solutions by means of electrochemical impedance spectroscopy

The effects of temperature, applied potential and hydrogen generation on the passive behaviour of nickel were investigated in lithium bromide aqueous solution using different electrochemical techniques: open circuit potential (OCP), potentiodynamic and potentiostatic measurements, and electrochemical impedance spectroscopy (EIS). From the polarization curves, it is observed that localised corrosion resistance decreases with temperature, the repassivation of nickel is more difficult at 75 °C and the hydrogen evolution reaction is favoured with an increase in temperature. Impedance results showed that the most suitable corrosion mechanism of nickel in LiBr solutions includes the double layer and the passive film formed on the nickel surface. The passive film of nickel partially disappears when a low cathodic potential is applied.     

Effect of second phases on the corrosion behaviour of wrought Mg-Zn-Y-Zr alloy

The corrosion behaviour of wrought Mg-Zn-Y-Zr alloy was investigated by corrosion morphology observation and electrochemical measurement. The results indicate that the corrosion process can be divided into three stages, corresponding to three types of corrosion features. At the initial stage, corrosion occurred surrounding the second phases, which was driven by galvanic couple effect; at the middle stage, filiform corrosion was found in the central regions of α Mg matrix; at the final stage, pitting corrosion presented around the second phases. The second phases have a great effect on the corrosion process of Mg-Zn-Y-Zr alloy.     

Limitations in the use of the potentiodynamic polarisation curves to investigate the effect of Zn on the corrosion behaviour of as-extruded Mg–Zn binary alloy

The effects of Zn on corrosion behaviour of as-extruded Mg-(1-4)Zn alloys were investigated using an immersion test, a zero resistance ammeter technique, and a potentiodynamic polarisation test. As a result, it was revealed that the solutionised Zn enhanced protectiveness of the passive film, and accelerated the H₂ evolution rate of the Mg–Zn binary alloys. The acceleration of the H₂ evolution rate by addition of Zn leads to an increase in the net corrosion rate of the Mg–Zn alloy. In this research, the polarisation test was found to have some limitations for evaluating the true corrosion behaviour of passive Mg–Zn alloy.     

Microbially influenced corrosion and inhibition of nickel–zinc and nickel–copper coatings by Pseudomonas aeruginosa

The present study describes the effect of Pseudomonas aeruginosa on the corrosion rate of nickel–zinc and nickel–copper alloy coatings. The presence of bacteria was associated with decreases in R_ct values, suggesting that P. aeruginosa promoted the corrosion of nickel–copper alloy coatings. However, R_ct values of nickel–zinc coatings increased in response to bacterial inoculation, corresponding to a decrease in corrosion rate for nickel–zinc alloy coatings. Our results suggest that the activity of P. aeruginosa facilitated the corrosion of nickel–copper alloy, while serving a protective function for the nickel–zinc alloy.     

Effect of surface nanocrystallization on the corrosion behaviour of AISI 409 stainless steel

The influence of surface mechanical attrition treatment (SMAT) on the corrosion behaviour of AISI 409 grade stainless steel in 0.6 M NaCl was studied. SMAT using 2 mm ∅ 316L stainless steel (SS) balls for 15, 30 and 45 min and 5 mm ∅ balls for 15 min offers a better corrosion protective ability. In contrast, treatment using 5 mm ∅ balls for 30 and 45 min and by using 8 mm ∅ balls for 15, 30 and 45 min, induces microstrain and defect density that results in a decrease in corrosion resistance.     

Electrochemical corrosion behaviour of Bi-11Ag alloy for electronic packaging applications

This study investigated the electrochemical corrosion properties of the solders for die-attach applications in 3.5% NaCl solution. Compared with Pb-5Sn and Zn-40Sn, Bi-11Ag exhibited higher corrosion potential and relatively low corrosion current density. The ductile Ag-rich phase which dispersed in the Bi matrix was able to accommodate the stress arising from the formation of a passive layer and contributed to the two-stage passivation. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) results confirm that the corrosion products comprised BiOCl, Bi₂O₃ and AgCl.     

Temperature effect in the corrosion resistance of Ni-Fe-Cr alloy in chloride medium

The corrosion susceptibility of alloy 33 in 0.5 mol/L sodium sulphate solutions containing or not 0.1 mol/L sodium chloride was tested at three different temperatures: 22 °C, 40 °C and 60 °C. Electrochemical studies were performed using corrosion potential measurements (E_corr) as well as potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques. Corrosion potential measurements showed that alloy 33 was passivated by a previously air formed film which was not destroyed during immersion in both solutions. No corrosion was observed during these tests although the temperature affected the film. Potentiodynamic polarization experiments showed that at high anodic potentials the previous film was broken up, and localized corrosion occurred in both solutions and at the three temperatures tested. Electrochemical impedance spectroscopy tests confirmed the presence of a stable passive film on the alloy surface at open circuit potential. Mott-Schottky analysis indicated that the passive film is an n-type semiconductor due to the presence of point defects of donor species, such as oxygen vacancies and interstitial metallic cations. As the potential increases the Cr(III) present in the barrier layer oxidizes producing Cr(VI) soluble species. The dissolution creates metallic cation vacancies that are acceptor species and the film changes from n-type to p-type semiconductor. The passive film rupture and the following localized attack are related to the drastic oxidative dissolution of the film at high anodic potentials, independent of its p-nature, chloride presence or increased temperature.     

Improving the corrosion behaviour of powder metallurgical 316L alloy by prepassivation in 20% nitric acid

The electrochemical improvement of PM 316L stainless steels by pre-alloyed powder prepassivation in 20% nitric acid in comparison with as-received specimens has been studied in this work. For comparison purposes a simultaneous study was carried out on similar composition wrought AISI 316L steels. Corrosion resistance was studied using evolution of the corrosion potential vs. time, anodic polarisations curves and Zero Resistance Ammeter technique. Reductions of the corrosion rate (i_corr) were observed in prepassivated specimens in neutral chloride media. Crevice resistance was higher for prepassivated specimens and for higher densities and annealing as post-heat treatments.     

Electrochemical behaviour of Cu-40Zn in 3% NaCl solution polluted by sulphides: Effect of aminotriazole

The electrochemical behaviour of Cu-40Zn alloy, in 3% NaCl medium pure and polluted by 2 ppm of S²⁻ ions, has been studied in the absence and presence of the 3-amino-1,2,4 triazole (ATA) as corrosion inhibitor. Electrochemical measurements (polarisation curves and electrochemical impedance spectroscopy) showed that sulphides accelerate the alloy corrosion. The studies revealed that ATA inhibits both cathodic and anodic reactions, indicating a mixed type of inhibition. The inhibiting effect was higher in presence of S²⁻ ions than in its absence. Scanning electron microscopy analysis showed that the inhibitor acts by preventing the adsorption of S²⁻ ions, and formation of Cu₂S at the alloy surface. The inhibition efficiency reaches 98% at a concentration of 5 × 10⁻³ M.     

Effects of microplasma arc AISI 316L welds on the corrosion behaviour of pipelines in LiBr cooling systems

The effect of microplasma arc welding (MPAW) on the electrochemical and corrosion behaviour of AISI 316L stainless steel tubes has been studied. Scanning electrochemical measurements were performed in sodium chloride to evaluate the difference in the electrochemical activity of base (non-welded) and welded samples. Oxygen reduction rates increase in AISI 316L due to the heat treatment effect induced by welding, indicating a higher electrochemical activity in the welded samples. Additionally, the use of MPA weldments in lithium bromide (LiBr) absorption machines was also analysed at typical operating temperatures and Reynolds numbers. The welding process increases corrosion rates, hinders passivation and increases the susceptibility to pitting attack in LiBr. However, zero-resistance ammeter and localization index measurements show that the galvanic pair generated between the base and welded alloys is weak, both electrodes being in their passive state. Temperature greatly affects the corrosion process.     

Inhibiting effect of 2-mercaptobenzimidazole on the corrosion of Cu-30Ni alloy in aerated 3% NaCl in presence of ammonia

The inhibiting effect of 2-mercaptobenzimidazole (MBI) against Cu-30Ni alloy corrosion in aerated 3% NaCl polluted by ammonia, has been developed. Potentiodynamic and electrochemical impedance spectroscopy (EIS) measurements have been applied to determine the corrosion rate. scanning electron microscopy (SEM) studied surface morphology has been used to characterise electrode surface. The obtained results indicate that MBI acts as a good mixed-type inhibitor retarding the anodic and cathodic reactions. An increase of MBI concentration leads to a decrease of corrosion rate and inhibition efficiency increase.     

Local and global electrochemical impedances applied to the corrosion behaviour of an AZ91 magnesium alloy

The electrochemical behaviour of an AZ91 magnesium alloy was investigated in a low aggressive medium by means of local and global electrochemical impedance measurements. The results were compared to those obtained on a pure magnesium sample. It was possible to show the individual contribution of each phase constituting the alloy, and it was observed that the corrosion mechanism of the two phases was the same, controlled by the Mg dissolution. However, local impedance diagrams clearly indicated that the kinetics dissolution of the β-phase was slower than that of the α-phase, which was in good agreement with SEM observations.     

Effect of antimony, bismuth and calcium addition on corrosion and electrochemical behaviour of AZ91 magnesium alloy

This study investigated the effect of antimony, bismuth and calcium addition on the corrosion and electrochemical behaviour of AZ91 magnesium alloy in 3.5% NaCl solution. Techniques including constant immersion, electrochemical potentiodynamic polarisation, scanning electron microscopy (SEM), energy dispersed spectroscopy (EDS) and X-ray diffraction (XRD) were used to characterise electrochemical and corrosion properties and surface topography. It was found that corrosion attack occurred preferentially on Mg₃Bi₂ and Mg₃Sb₂ particles while Mg₁₇Al₈Ca_0.5 and Mg₂Ca phases showed no detrimental effect on corrosion. Combined addition of small amounts of bismuth and antimony to the AZ91 alloy resulted in significant increase in corrosion rate.