Hot corrosion of a novel NiO/NiFe2O4 composite coating thermally converted from the electroplated Ni–Fe alloy

A novel NiO/NiFe₂O₄ composite coating thermally converted from an electroplated Ni–Fe alloy was successfully fabricated. The composite coating consisted of a NiO matrix and homogeneously distributed criss-cross intragranular and intergranular NiFe₂O₄ precipitates, with a very dense and flat structure. The composite, compared to bare Ni metal, exhibited increased hot corrosion resistance under an atmosphere of Na₃AlF₆–AlF₃–CaF molten salts and air at 960 °C, mainly because of the dense structure and well-adhered, homogeneously dispersed intragranular and intergranular NiFe₂O₄ precipitates.     

Hot corrosion of YSZ/Al2O3 dispersed NiCrAlY plasma-sprayed coatings in Na2SO4-10 wt.% NaCl melt

This study examines the effect of ytrria stabilized zirconia (YSZ) dispersion on hot corrosion behaviour of NiCrAlY bond coat. Hot corrosion studies were conducted on NiCrAlY and NiCrAlY containing 25, 50 and 75 wt.% YSZ coatings obtained through the air plasma spray technique, in Na₂SO₄ + 10 wt.% NaCl environment at 800 °C. The results show that YSZ dispersion lowers the overall hot corrosion tendency of the NiCrAlY, though it enhances the inherent hot corrosion tendency of its metallic constituent (NiCrAlY). Furthermore, there exists a threshold oxide level beyond which it adversely affects the hot corrosion of the coating.     

Hot corrosion behaviour of Yb2Zr2O7 ceramic coated with V2O5 at temperatures of 600-800 °C in air

To better understand the hot corrosion behaviour of Yb₂Zr₂O₇ ceramic in molten V₂O₅, hot corrosion experiments were performed in a temperature range of 600-800 °C in air. Different reaction products of ZrV₂O₇, YbVO₄ and m-ZrO₂ were identified depending upon the hot corrosion conditions, for example, ZrV₂O₇ and YbVO₄ at 600 °C for 2 h and 8 h; ZrV₂O₇, m-ZrO₂ and YbVO₄ at 700 °C for 2 h; m-ZrO₂ and YbVO₄ either at 800 °C for 2 h or at 700-800 °C for 8 h. The hot corrosion reaction mechanisms were further discussed based on the thermal instability of ZrV₂O₇ at elevated temperatures.     

Preparation and hot corrosion behaviour of a MCrAlY + AlSiY composite coating

A MCrAlY + AlSiY composite coating was prepared by arc ion plating. Hot corrosion behaviours of the composite coating and the reference NiCoCrAlYSiB coating were investigated. The results indicate that the composite coating consisted of β-(Ni,Co)Al with dispersed σ-NiCoCr and Cr₃Si in outer layer and Cr-rich phases in inner layer after annealing. As being corroded for 200 h, the composite coating proved better corrosion resistance than that of reference NiCoCrAlYSiB coating. The enhanced corrosion resistance of the composite coating was due to the gradient distribution of Al-enriched outer layer and Cr-enriched inner layer.     

Hot corrosion behaviour of plasma sprayed YSZ/LaMgAl11O19 composite coatings in molten sulfate–vanadate salt

Hot corrosion studies of thermal barrier coatings (TBCs) with different YSZ/LaMgAl₁₁O₁₉ (LaMA) composite coating top coats were conducted in 50 wt.% Na₂SO₄ + 50 wt.% V₂O₅ molten salt at 950 °C for 60 h. Results indicate that TBCs with composite coating top coats exhibit superior oxidation and hot corrosion resistances to the TBC with the traditional YSZ top coat, especially for which has a LaMA overlay. The presence of LaMA can effectively restrain the destabilization of YSZ at the expense of its own partial degradation. The hot corrosion mechanism of LaMA coating and the composite coatings have been explored.     

Ion-plated Al-Al2O3 films as diffusion barriers between NiCrAlY coating and orthorhombic-Ti2AlNb alloy

Ion-plated Al-Al₂O₃ cermet films were fabricated as diffusion barriers between NiCrAlY coating and orthhombic-Ti₂AlNb alloy. The oxidation and interdiffusion behaviour of coatings with and without diffusion barrier were investigated in isothermal and cyclic oxidation tests at 800 °C. The results indicated that substantial interdiffusion and rapid oxidation degradation occurred in the coated specimens without diffusion barrier. With Al-Al₂O₃ diffusion barriers, deferred interdiffusion and improved oxidation resistance was observed. Among them, duplex coating containing 1Al-Al₂O₃ interlayer exhibited the best performance. Coefficient of diffusion hindering and factor of reaction hindering were proposed to compare and quantify the efficiency of the diffusion barriers.     

Inert anode composed of Ni–Cr alloy substrate, intermediate oxide film and α-Al2O3/Au (Au–Pt, Au–Pd, Au–Rh) surface composite coating for aluminium electrolysis

An inert anode composed of alloy substrate, intermediate oxide film and surface composite coating for aluminium electrolysis has been fabricated. The intermediate oxide film (ZrO₂/Y₂O₃) provides good adhesion and mutual diffusion resistance between the substrate and the surface coating which consists of α-Al₂O₃ particles embedded in Au (Au–Pt, Au–Pd, Au–Rh) matrix. The results of electrolysis test revealed that aluminium with high purity (>99.999%) can be produced. It is demonstrated that the inert anode exhibits superior erosion and corrosion resistance during aluminium electrolysis, especially in low-temperature (800 °C) electrolytes.     

High temperature corrosion behaviour of a gradient NiCoCrAlYSi coating II: Oxidation and hot corrosion

The high temperature oxidation and hot corrosion behaviour of a NiCoCrAlYSi coating and a gradient coating were investigated. The gradient coating showed better performance of re-healing alumina scale due to its possession of more β phase as Al reservoir. The degradation process of the gradient coating was favorably retarded by the formation of Cr(W)-rich σ precipitates in the interdiffusion zone. The corrosion results also confirmed an improved corrosion resistance of the gradient coating. The improved high temperature performance of the gradient coating owes to the Al enrichment of Al in the outer layer.     

Oxidation and interfacial fracture behaviour of NiCrAlY/Al2O3 coatings on an orthorhombic-Ti2AlNb alloy

Al₂O₃ diffusion barriers of various thicknesses have been fabricated by filtered arc ion plating between the NiCrAlY coating and the O-Ti₂AlNb alloy. Isothermal oxidation tests and three-point bend tests have been conducted to investigate the influence of the Al₂O₃ diffusion barriers on the oxidation and interfacial fracture behaviour of the coatings. The results indicate that the Al₂O₃ diffusion barrier defers interdiffusion and gives oxidation resistance of the NiCrAlY coatings. The thickness of the Al₂O₃ interlayer not only influences the oxidation behaviour but also affects the interfacial fracture properties. Additionally, thermal exposure affects the critical load in three-point bend tests.     

Microstructure and oxidation behaviour of an AlSiY/NiCrAlYSi composite coating at 1150 °C

A composite coating consisting of an outer AlSiY layer and an inner NiCrAlYSi layer has been prepared by a two-step arc ion plating method. The isothermal and cyclic oxidation behaviour of the composite coating at 1150 °C, including the growth of oxide scale and the microstructure transformation of the coatings, have been investigated comparing with the reference coating, NiCrAlYSi. The results show enhanced oxidation performance of the composite coating, which is concerned with its abundant possession of β-NiAl phase reservoirs, providing it the long term healing capacity of re-growing the α-Al₂O₃ scale.     

Hot corrosion behaviour of Ni3Al in sulphate-chloride mixtures in the atmosphere

Hot corrosion of Ni₃Al intermetallic compound in the presence of sulphate-chloride mixtures was studied. A comminuted Ni₃Al mixed with NaCl-Na₂SO₄, NaCl-Li₂SO₄, LiCl-Na₂SO₄, LiCl-Li₂SO₄ additions was oxidized in the air up to 1000 °C with linearly increasing temperature and isothermally within the temperature range of 500-700 °C. The corrosion process was observed by thermogravimetric method using Mettler thermoanalyzer.The experiments indicated that LiCl (∼10 wt.%)-Li₂SO₄ mixture was the most corrosive agent. It was also found that by addition of MgO the corrosion of Ni₃Al was reduced. Phase composition of the corrosion products was established by X-ray diffraction analysis; there were detected Al₂O₃, Al₂S₃, NaAlO₂ (or LiAlO₂) as intermediate products, nickel sulphides, NiO and NiAl₂O₄. NiAl₂O₄ spinel was formed only at the highest temperatures, while at lower temperatures alumina was present instead of spinel.Hot corrosion behaviour of Ni₃Al in sulphate-chloride mixtures in air atmosphere.     

Thermodynamic and kinetic consideration on the corrosion of Fe, Ni and Cr beneath a molten KCl-ZnCl2 mixture

Thermogravimetric (TG) experiments have been carried out to study the kinetics of hot corrosion of Fe, Cr and Ni, covered by a molten KCl-ZnCl₂ mixture of a composition close to the eutectic (50 mol% KCl-50 mol% ZnCl₂). Furthermore binary and ternary phase diagrams were calculated in order to describe the corrosion process. The tests were conducted at a temperature of 320 °C in an atmosphere consisting of argon and oxygen. For iron different stages are observed in a TG curve. They can be attributed to the different reaction steps of iron chloride formation (incubation phase), oxide precipitation (linear stage) and scale formation (parabolic or logarithmic stage). Based on these observations a model, described by Spiegel [A. Spiegel, Molten Salt Forum 7 (2003) 253], is confirmed. For Cr and Ni these stages are not observed. At 8 vol% O₂ only slight oxidation of Cr and Ni was observed accompanied by evaporation of the salt deposit. At 16 vol% O₂ the rate of oxidation increases and the experiments yield a curve that is either parabolic or logarithmic for both Ni and Cr. As a result it is shown that the solubility of iron chloride in the KCl-ZnCl₂ melt is higher than the solubility of nickel chloride and chromium (III) chloride in the KCl-ZnCl₂ melt. This enables a higher diffusibility of iron chloride to the upper region of the melt where a higher oxygen partial pressure (p(O₂)) is present leading to a higher oxidation rate of iron.     

Electrochemical impedance studies of the initial-stage corrosion of 310S stainless steel beneath thin film of molten (0.62Li, 0.38K)2CO3 at 650 °C

Electrochemical impedance spectroscopy (EIS) has been used to study the initial-stage corrosion of 310S stainless steel beneath thin film of molten (0.62Li, 0.38 K)₂CO₃ at 650 °C in air. Two-electrode system is used to fabricate molten-salt film. The thickness of molten salt approximated from electrolyte resistance decreases rapidly until it is smaller than 6 mg/cm². The appearance of diffusion-related impedance at the end of the test is linked to the severe loss of molten salt which causes twisted diffusion paths. More molten salt on the surface of 310S causes a longer lithiation process and more profound degradation of the oxide film.     

Corrosion behaviour of Y2O3-ZrO2 coatings on IN713LC in a LiCl-Li2O molten salt

Hot corrosion studies were performed on superalloy specimens. The IN713LC superalloy were sprayed with an aluminized NiCrAlY-bond coat and then with an yttria-zirconia top coat. The bare superalloy reveals an obvious weight loss due to spalling of the scales by the rapid scale growth and thermal stress. The top coatings showed a much better hot corrosion resistance in the presence of LiCl-3 wt.% Li₂O molten salt when compared with those of the bare superalloy and the aluminized bond coatings. These coatings have been found to be beneficial for increasing hot corrosion resistance of structural materials for lithium molten salts.     

Electrolytic MgO/ZrO2 duplex-layer coating on AZ91D magnesium alloy for corrosion resistance

By a two-step fabrication process of electrolytic deposition and annealing treatment, an MgO/ZrO₂ duplex-layer coating has been prepared on AZ91D magnesium alloy as a protective film against corrosion. Owing to the chemical bonding formed after the condensation of precursory hydroxides, the adhesion strength, thickness and compactness of MgO coating on the substrate are significantly enhanced by the intermediate ZrO₂ layer which prevents the formation of corrosion product Mg₂(OH)₃Cl·4H₂O. As a result, the MgO/ZrO₂ duplex-layer coated specimen reveals relatively high corrosion resistance and superior stability in 3.5 wt% NaCl solution with respect to the MgO single-layer coated specimen.     

The role of microstructure in the high temperature oxidation mechanism of Cr3C2-NiCr composite coatings

Composites of Cr₃C₂-NiCr provide superior oxidation resistance to WC-Co composites, which has seen them applied extensively to components subjected to combined high temperature erosion and oxidation. This work characterises the variation in oxidation mechanism of thermally sprayed Cr₃C₂-NiCr composites at 700 °C and 850 °C as a function of heat treatment. Carbide dissolution during spraying increased the Ni alloy Cr concentration, minimising the formation of Ni oxides during oxidation. Compressive growth stresses resulted in ballooning of the oxide over the carbide grains. Carbide nucleation with heat treatment reduced the Ni alloy Cr concentration. The oxidation mechanism of the composite coating changed from being Cr based to that observed for NiCr alloys.     

Development and oxidation resistance of air plasma sprayed Mo-Si-Al coating on an Nbss/Nb5Si3 in situ composite

A Mo-Si-Al coating, which is mainly composed of Mo(Si,Al)₂ and Mo₅(Si,Al)₃, was developed to protect a Nb_ss/Nb₅Si₃ in situ composite by air plasma spraying. After oxidation at 1250 °C, the oxidation curve followed parabolic law and even after oxidation for 100 h, the weight gain of Mo-Si-Al coating was 8.24 mg/cm². The surface of the oxidized samples became flatter and smoother as time increased due to the formation of SiO₂ glass. Moreover, the microstructure of Mo-Si-Al coating changed and a layer structured interdiffusion zone was formed at the substrate-coating interface after oxidation.     

The effect of Al content on the galvanic corrosion behaviour of coupled Ni/graphite and Ni–Al coatings

In this study, the corrosion behaviour of 75Ni/25graphite abradable coating and Ni–Al bonding coatings with different Al content were investigated with open circuit potential and polarization tests. The galvanic corrosion of the coupled Ni/graphite and Ni–Al coatings was studied by using a zero-resistance ammeter in 5 wt% NaCl solution. The experimental results showed that the corrosion resistance of the Ni–Al coatings decreased with increasing Al contents. In the galvanic corrosion test, the Ni–Al coatings with high Al contents (80Ni–20Al, 85Ni–15Al, and 90Ni–10Al) were the anodic element of the couples, while, the 95Ni–5Al acted as the cathode element in the couple.     

Microstructure, spallation and corrosion of plasma sprayed Al2O3–13%TiO2 coatings

The electrochemical corrosion behaviours of the steel substrates coated with three different plasma sprayed Al₂O₃–13%TiO₂ coatings were studied in this paper. The three kinds of Al₂O₃–13%TiO₂ coatings were conventional ME coating, nanostructured NP coating and NS coating. There were micro cracks, laminar splats and straight columnar grains in ME coating. For the two nanostructured coatings, the laminar microstructure and columnar grains were not obvious. The NP coating had the highest hardness and spallation resistance. Electrochemical corrosion behaviour of the three coatings was mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) in aqueous Na₂SO₄ solution.     

Discontinuous oxidation and erosion-oxidation of a CeO2-dispersion-strengthened chromium coating

A CeO₂-dispersion-strengthened chromium coating was developed on a carbon steel using a two-step process: prior electrodeposition of a Ni-CeO₂ nanocomposite film and subsequent chromization using a conventional pack cementation method. Compared to the CeO₂-free coatings prepared on the carbon steel without and with pre-electrodeposition of a pure Ni film, the CeO₂ dispersed chromium coating offered profoundly improved discontinuous oxidation resistance at 900 °C in 5% O₂ + N₂ and in 5% O₂ + 1000 ppm SO₂ + N₂, and erosion-oxidation resistance in a laboratory-scale fluidized-bed combustor (FBC), mainly because of the development of a denser, less wrinkled and more adherent chromia scale.