Influence of Zn injection on characteristics of oxide film on 304 stainless steel in borated and lithiated high temperature water

The oxide film on 304 stainless steel exposed to the hydrothermal environments at 573.15 K up to 20 days without/with 10 ppb Zn injection has been investigated ex situ by X-ray photoelectron spectroscopy (XPS). ZnFe₂O₄ and ZnCr₂O₄ were found to be formed in the oxide film at the initial stage of immersion by substitution reaction between Zn²⁺ and Fe²⁺, and ZnCr₂O₄ became dominant after long-term immersion. The calculations of potential-pH diagrams, solubilities and crystallographic features of spinels have been done to evaluate the oxide film structure and the inhibition mechanism caused by Zn injection.     

Influence of pH on electrochemical properties of passive films formed on Alloy 690 in high temperature aqueous environments

Passive films formed on Alloy 690 in different pH solutions at high temperatures were studied by potentiodynamic polarization, Auger electron spectroscopy, thermodynamic diagrams and the Mott–Schottky relation. The chemical compositions and electronic structures of the passive films were found to be strongly pH-dependent. In alkaline solutions, a secondary passivation was clearly observed on potentiodynamic polarization curves. The passive films were a mixture of Cr₂O₃ and FeCr₂O₄ below the flat band potential of nickel oxide and were NiFe₂O₄ above this potential. Electronic structure models, describing the electrochemical properties of the passive films, are proposed and discussed.     

Oxidation kinetics and mechanisms of Ni-base alloys in pressurised water reactor primary conditions: Influence of subsurface defects

Oxidation of Alloy 690 in PWR primary water conditions has been investigated, considering particularly the role played by subsurface structural defects. To simulate a defective surface state, Xe implantation has been set up on samples. Corrosion experiments were thereafter performed in a corrosion loop simulating the PWR medium with durations between 24 h and 1000 h. Microstructural observations and NRA measurements underlined the role played by defects on the crystallinity of the continuous oxide spinel layer, on the nucleation of Cr₂O₃ nodules and on the oxidation rate. The higher defects concentration seemed to modify the oxygen diffusion in the oxide scale.     

Analysis of the electrochemical reaction behavior of alloy AZ91 by EIS technique in H3PO4/KOH buffered K2SO4 solutions

The EIS technique was used to analyze the electrochemical reaction behavior of Alloy AZ91 in H₃PO₄/KOH buffered K₂SO₄ solution at pH 7. The corrosion resistance of Alloy AZ91 was directly related with the stability of Al₂O₃ · xH₂O rich part of the composite oxide/hydroxide layer on the alloy surface. The break down of the oxide layer was estimated to occur mainly on the matrix solid solution phase in Alloy AZ91. The mf capacitive loop arose from the relaxation of mass transport in the solid oxide phase in the presence of Al₂O₃ · xH₂O rich part and from Mg⁺ ion concentration within the broken area in the absence of Al₂O₃ · xH₂O rich part in the composite oxide structure on the alloy surface. The lf inductive loop had tendency of disappear when the dissolution rate of the alloy decreased as a result of the formation of the protective oxide layer.     

The mechanism of oxide film formation on Alloy 690 in oxygenated high temperature water

Oxide films formed on Alloy 690 exposed to 290 °C water containing 3 ppm O₂ were investigated. It was found that Cr rich oxides form initially through solid-state reactions. Ni–Fe spinels gradually develop on surface layer by precipitation with increasing immersion time. Initially formed Cr rich oxides react with outwards diffusing Ni and Fe to form small spinel particles which then vanish gradually. An inner layer develops from oxide/matrix interface through inward diffusion of oxidant. Cr is preferentially oxidized and tends to dissolve into solution. The resultant inner layer consists of predominant NiO which cannot serve as a protective barrier layer.     

Corrosion characteristics of LiBH4 film exposed to a CO2/H2O/O2/N2 mixture

LiBH₄ films were prepared by pulsed laser deposition using a LiB target in a background pressure of hydrogen. The corrosion characteristics of LiBH₄ films were measured by exposing them to a gas mixture of CO₂/H₂O/O₂/N₂ at ambient temperature for 1–24 h. Scanning electron microscopy images show some cracks on the surface of corrosion films, which could act as easy paths for H₂O and CO₂ to further react with Li⁺ and B³⁺. The X-ray photoelectron spectroscopy results and theoretical analysis show that LiBH₄ tends to react with H₂O and CO₂ to form Li₂B₄O₇, Li₂CO₃ and LiOH during the corrosion process.     

Effects of hydrogen on the anodic behavior of Alloy 690 at 60 °C

Polarization and electrochemical impedance spectroscopy (EIS) measurements, Mott-Schottky (M-S) analysis and X-ray photoelectron spectroscopy (XPS) were used to investigate the effects of hydrogen on the anodic behavior of a one-dimensionally (1D) 25% cold worked (CW) Alloy 690 thermal treated (TT) in a boric acid and sodium sulphate solution at 60 °C. The pre-hydrogen-charged specimen exhibited a higher anodic current than that of the uncharged specimen below the transpassive potential. The charged hydrogen can be trapped in the metal. Electrochemical impedance spectroscopy (EIS) showed that the resistance capacitance loop of the hydrogen-charged specimen was significantly smaller than that of the uncharged specimen. Mott-Schottky analyses indicated that the passive film formed on Alloy 690 at −0.2 V_SCE was an n-type semiconductor, with a p-n hetero-junction at 0.2 V_SCE. Charged hydrogen increased the carrier density and the thickness of the passive film both at −0.2 V_SCE and 0.2 V_SCE. The Ni/Cr ratio in the surface film decreased after hydrogen charging, indicating that charged hydrogen could enhance the oxide film growth by increasing the OH⁻ (O²⁻) concentrations through its reaction with vacancies.     

The role of TiN inclusions in stress corrosion crack initiation for Alloy 690TT in high-temperature and high-pressure water

Microchemistry and microstructure of TiN in Alloy 690TT were analyzed using SEM and TEM. Constant loading test was conducted on Alloy 690TT in 325 °C water to study effect of TiN on SCC initiation. It was found that TiN-inclusion stringers existed along the longitudinal axis. Numerous micron-size TiN with Al₂O₃ and/or MgO nuclei and submicron-size TiN existed in this alloy. After holding a constant load equal to 180% of the yield strength for 40 days, cracks about 1-3 μm initiated at micron-size TiN and TiN-inclusion stringers in the near surface. The mechanisms of Alloy 690TT crack initiation at these TiN are discussed.     

Gamma-radiation-induced corrosion of carbon steel in neutral and mildly basic water at 150 °C

The effect of γ-radiation on the kinetics of carbon steel corrosion has been investigated by characterizing the oxide films formed on steel coupons at 150 °C and at two pH values. Results show that continuous irradiation enhances surface oxide formation with the type of oxide formed dependant on the solution pH. For experiments at 150 °C and a [OH⁻] equivalent to that for pH_{25 °C} = 10.6, the surface oxide on carbon steel after γ-irradiation was non-porous and uniform, and no localized corrosion was observed. This oxide, however, appears to be susceptible to brittle fracture during cooling. Raman spectroscopy of the surface film indicates that it is a mixture of the phases of Fe₃O₄ and γ-Fe₂O₃. In contrast, at 150 °C with [OH⁻] equivalent to neutral pH_{25 °C}, metal dissolution is significant and the surface oxide film is very porous. Raman spectra show that this oxide film is also composed of a mixture of Fe₃O₄ and γ-Fe₂O_3. The results from this work combined with previously reported electrochemical studies of the same system as a function of pH and temperature can be used to deconvolute the effects of radiation, pH and temperature on the nature of the corrosion process.     

Zinc treatment effects on corrosion behavior of 304 stainless steel in high temperature, hydrogenated water

Trace levels of soluble zinc(II) ions (30 ppb) maintained in mildly alkaline, hydrogenated water at 260 °C were found to lower the corrosion rate of austenitic stainless steel (UNS S30400) by about a factor of five, relative to a non-zinc baseline test [S.E. Ziemniak, M. Hanson, Corros. Sci. 44 (2002) 2209] after 10,000 h. Characterizations of the corrosion oxide layer via grazing incidence X-ray diffraction and X-ray photoelectron spectroscopy in combination with argon ion milling and target factor analysis, revealed that miscibility gaps in two spinel binaries—Fe(Fe_1−mCr_m)₂O₄ and (Fe_1−nZn_n)Fe₂O₄—play a significant role in determining the composition and structure of the corrosion layer(s). Although compositions of the inner and outer corrosion oxide layers represent solvus phases in the Fe₃O₄-FeCr₂O₄ binary, zinc(II) ion incorporation into both phases leads to further phase separation in the outer (ferrite) layer. Recrystallization of the low zinc content ferrite solvus phase is seen to produce an extremely fine grain size (∼20 nm), which is comparable in size to grains in the inner layer and which is known to impart resistance to corrosion. Zinc(II) ion incorporation into the inner layer creates additional corrosion oxide film stabilization by further reducing the unit cell dimension via the substitution reaction

0.2Zn²⁺(aq)+Fe(Fe_0.35Cr_0.65)₂O₄(s)?0.2Fe²⁺(aq)+(Zn_0.2Fe_0.8)(Fe_0.35Cr_0.65)₂O₄(s)     

Electrochemical properties and growth mechanism of passive films on Alloy 690 in high-temperature alkaline environments

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.     

Effect of dissolved hydrogen on the electrochemical behaviour of Alloy 600 in simulated PWR primary water at 290 °C

With an increase in dissolved hydrogen (DH) content from 0 to 5 cm³ STP H₂/kg H₂O the electrochemical behaviour of Alloy 600 in deaerated PWR primary water at 290 °C was investigated, using corrosion potential (E_corr) monitoring, potentiodynamic polarization, cyclic voltammetry and electrochemical impedance spectroscopy (EIS). DH content controls the E_corr of Alloy 600. Raising DH content directly promotes the cathodic process and reduces the passivity of Alloy 600 significantly. EIS results show that increasing DH content results in a thinner inner-layer oxide film and ions diffusion becomes easier. The mechanism of these DH effects is discussed.     

The initial stage of pitting corrosion on coated steels investigated by photon rupture in chloride containing solutions

A photon rupture method, film removal by a focused pulse of pulsed Nd-YAG laser beam irradiation, has been developed to enable oxide film stripping at extremely high rates without contamination from the film removal tools. In the present study, Zn-55mass%Al alloy and Al-9mass%Si alloy-coated steel specimens covered with protective nitrocellulose film were irradiated with a focused pulse of a pulsed Nd-YAG laser beam at a constant potential in 0.5 kmol m⁻³ H₃BO₃-0.05 kmol m⁻³ Na₂B₄O₇ (pH = 7.4) with 0.01 kmol m⁻³ of chloride ions to investigate the initial stage of localized corrosion. At low potentials, oxide films on both coated alloys were reformed after the nitrocellulose films were removed by this method. The oxide film formation kinetics follows an inverse logarithmic law, in agreement with Cabrera-Mott theory. However, at high potentials, localized corrosion producing corrosion products occurs at the area where nitrocellulose film was removed. Nevertheless, when the applied potential is less noble, the dissolution current of the Zn-55mass%Al-coated steel samples is higher than that of Al-9mass%Si-coated samples.     

Effect of Caand Mg on corrosion and scaling of galvanized steel pipe in simulated geothermal water

In this paper, the effects of scaling ions (Ca²⁺ and Mg²⁺) on corrosion and scaling processes of galvanized steel pipe in geothermal water are presented. Spherical corrosion products and needle-shaped scale coexisted on the pipe surface. The concentration of Zn²⁺ and OH⁻ affected the nuclei formation of scale. The corrosion products and scale were identified as Zn(OH)₂, ZnO, CaCO₃ and MgCO₃, respectively. When scale formed on the galvanized steel pipe, the corrosion rate slowed down and the pitting region became smaller.     

Self-healing mechanism of a protective film prepared on a Ce(NO3)3-pretreated zinc electrode by modification with Zn(NO3)2 and Na3PO4

Self-healing mechanism of a protective film against corrosion of zinc at scratches in an aerated 0.5 M NaCl solution was investigated by polarization measurements, X-ray photoelectron spectroscopy (XPS) and electron-probe microanalysis (EPMA). The film was prepared on a zinc electrode by treatment in a Ce(NO₃)₃ solution and addition of aqueous solutions containing 9.98 or 19.9 μg/cm² of Zn(NO₃)₂ · 6H₂O and 55.2 μg/cm² of Na₃PO₄ · 12H₂O. After the coated electrode was scratched with a knife-edge crosswise and immersed in the NaCl solution for many hours, polarization measurements, observation of pit formation at the scratches, XPS and EPMA were carried out. This film was remarkably protective and self-healing against zinc corrosion on the scratched electrode. The cathodic and anodic processes of zinc corrosion were markedly suppressed by coverage of the surface except for scratches with a thin Ce₂O₃ layer containing a small amount of Ce⁴⁺ and the surface of scratches with a layer composed of Zn₃(PO₄)₂ · 4H₂O, Zn(OH)₂ and ZnO mostly.     

Corrosion processes of Mg–Y–Nd–Zr alloys in Na2SO4 electrolyte

The corrosion behavior of Mg–Y–Nd–Zr (WE43 commercial alloy) was investigated in Na₂SO₄ electrolyte using potentiodynamic polarization curves, X-Ray Photoelectron Spectroscopy (XPS), Time-of-Flight Secondary Ion Mass Spectrometry (ToF-SIMS) depth profiles, Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDS) analyzes. SEM and EDS data show that Nd-rich precipitates are mainly located at the grains boundaries. Zr/Y-rich zones are distributed inside the most of the grains. XPS study indicates a depletion of Mg on surface that could be attributed to Mg dissolution and an enrichment of the addition element oxides. XPS and ToF-SIMS analyzes demonstrate that the corrosion films are made up of a magnesium hydroxide (Mg(OH)₂) outer layer and an inner layer containing magnesium oxide (MgO), yttrium oxide (Y₂O₃) and hydroxide (Y(OH)₃), mixed with a small amount of MgH₂, zirconium oxide (ZrO₂) and neodymium oxide (Nd₂O₃). The Y₂O₃ and Y(OH)₃ signals increase slightly in the inner layer towards the corrosion film/alloy interface. Unlike these compounds, ZrO₂ and Nd₂O₃ compound signals are constant inside the inner layer. It is concluded that: (i) neodymium, zirconium and yttrium play a key role in the slightly improved corrosion resistance of the alloy and (ii) the cathodic reaction is slower on WE43 than on pure Mg and AZ91.     

Characterisation of oxide films formed on Co–29Cr–6Mo alloy used in die-casting moulds for aluminium

Oxide films formed at 700 °C on Co–29Cr–6Mo alloy were characterised extensively to improve the corrosion resistance of the alloy to liquid Al, enabling its use in Al die-casting moulds. Film of duplex layer consisting of an outer CoO-rich layer and an inner Cr₂O₃-rich layer was observed in samples subjected to oxidation for 4 h. With an increase in duration of oxidation, CoO was gradually replaced by Cr₂O₃, resulting in a single-layered oxide film dominantly composed of Cr₂O₃. The oxide film evolved with duration of oxidation treatment indicating the possibility of optimising films for Al die-casting moulds.     

Influence of oxygen ion irradiation on the corrosion aspects of Ti-5%Ta-2%Nb alloy and oxide coated titanium

The corrosion resistance of Ti-5%Ta-2%Nb alloy and DOCTOR (double oxide coating on titanium for reconditioning) coated titanium by O⁵⁺ ion irradiation were compared and investigated for their corrosion behaviour. O⁵⁺ ion irradiations were carried out at a dose rate of 1 × 10¹⁷, 1 × 10¹⁸ and 1 × 10¹⁹ ions/m² at 116 MeV. The surface properties and corrosion resistance were evaluated by using scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive X-ray (EDX), glancing-angle X-ray diffraction (GXRD) and electrochemical testing methods. The results of electrochemical investigations in 11.5 N HNO₃ indicated that the open circuit potential (OCP) of DOCTOR coated titanium is nobler than Ti-5%Ta-2%Nb alloy. The potentiodynamic polarization study of Ti-5%Ta-2%Nb alloy and DOCTOR coated specimen indicated decrease in passive current density with increase in ion doses (1 × 10¹⁷ to 1 × 10¹⁹ ions/m²) indicating decrease in anodic dissolution. Nyquist arc behaviour in the electrochemical impedance study substantiated the enhancement in oxide layer stability by O⁵⁺ ion irradiation. AFM results revealed that the DOCTOR coated Ti surface was dense without gross voids, and the surface roughness decreased by O⁵⁺ ion irradiation, but increased after corrosion test. EDX and GXRD patterns of DOCTOR coated Ti sample indicated that the coating was mainly composed of rutile TiO₂. Based on the above results, the O⁵⁺ ion irradiation effect on corrosion behavior of Ti-5%Ta-2%Nb alloy and DOCTOR coated titanium are discussed in this paper.     

Detrimental role of LiOH on the oxide film formed on Zircaloy-4

To understand the degradation behavior of Zircaloy-4 corroded in LiOH aqueous solution, X-ray diffraction was performed to analyze the crystal structure of Zircaloy-4 oxide formed in three different media. Second ion mass spectrometry (SIMS) was utilized to measure the penetration of Li⁺ and OH⁻ into the oxide film when Zircaloy-4 is exposed in LiOH aqueous solution. It was found that the SIMS depth profile of OH⁻ in the oxide film is in accord with that of Li⁺, which indicates that there exists OH⁻ in the oxide film. Based on the results, it is put forward that OH⁻ diffuses faster than O⁻² in the oxide films, which can enhance the corrosion rate of Zircaloy-4 and the transformation from tetragonal zirconia (t-ZrO₂) to monoclinic zirconia (m-ZrO₂). OH⁻ plays a detrimental role on the oxide film formed on Zircaloy-4.     

Influence of incorporated Mo and Nb on the Mott-Schottky behaviour of anodic films formed on AISI 304L

The effect of incorporated Mo and Nb on the electronic properties of oxide films formed on AISI 304L was investigated by Mott-Schottky analysis. The films show a bi-layer structure and behave as n-type and p-type semiconductors at potentials above and below the flat band potential. The inner p-type layer is Cr-enriched, while the outer n-type layer shows a slight increase in Fe-content close to the outer surface, where NbO³⁺-oxalate or MoO₄²⁻ incorporation occurred. The observed enhancement of pitting corrosion resistance of anodized steels is most probably related to compositional changes and thickness increase of the film after the surface treatments.