Halide aerosols in circulating fluidised bed co-combustion. Role of coal bound kaolin

An experimental campaign was carried out with a circulating fluidised bed (CFB) pilot scale combustor to study the role of coal bound kaolin in the fate of solid recovered fuel (SRF) originated halide aerosols. A combustion experiment was carried out with SRF-Spruce Bark mixture as a reference. High kaolinite coal and paper pigment kaolin, one at a time, were mixed with the SRF-Bark in increasing proportions until dp < 1 μm fine particles were absent as measured from 780 °C combustion gases by means of a dilution probe and low pressure impactor (LPI). This fine particle mode was absent after mixing sufficiently either coal or kaolin with SRF-Bark and only traces of water soluble alkali metal salts were found in the CFB fly ash. These conditions were achieved when kaolin was mixed with the SRF-Bark for 52 times on a molar basis compared to the Na + K initially found in the aerosols. This proportioning was found to be the same for the additive kaolin and coal bound kaolinite. Na and K in the fly ash seem to be bound chemically to the kaolin as alkali aluminosilicates rather than in water soluble alkali sulphates. This is indicated by their solubility behaviour.     

An experimental study on gasification of Colombian coal in fluidised bed

The main results of an experimental work on gasification of Colombian coal in a fluidised bed are reported in this paper. Experiments were carried out at different steam/coal (F_s/F_c) and air/coal (F_a/F_c) ratios and temperatures of gasifying agent. In addition, the influence of bed temperature on coal conversion was analysed. Results show a maximum value in the curve of high heating value versus F_a/F_c. From the environmental standpoint, low concentrations of sulphur compounds were obtained but more work should be done in order to decrease particulate matter.     

A technical and environmental analysis of co-combustion of coal and biomass in fluidised bed technologies

The use of biomass, which is considered to produce no net CO₂ emissions in its life cycle, can reduce the effective CO₂ emissions of a coal-fired power generation system, when co-fired with the coal, but may also reduce system efficiency.The technical and environmental analysis of fluidised bed technologies, using the ECLIPSE suite of process simulation software, is the subject of this study. System efficiencies for generating electricity are evaluated and compared for the different technologies and system scales.Several technologies could be applied to the co-combustion of biomass or waste and coal. The assessment studies here examine the potential for co-combustion of (a) a 600 MWe pulverised fuel (PF) power plant (as a reference system), (i) co-firing coal with straw and sewage sludge and (ii) using straw derived fuel gas as return fuel; (b) a 350 MWe pressurised fluidised bed combustion (PFBC) system co-firing coal with sewage sludge; (c) 250 MWe and 125 MWe circulating fluidised bed combustion (CFBC) plants co-firing coal with straw and sewage sludge; (d) 25 MWe CFBC systems co-firing low and high sulphur content coal with straw, wood and woody matter pressed from olive stones (WPOS); (e) 12 MWe CFBC co-firing low and high sulphur content coal with straw or wood; and (f) 12 MWe bubbling fluidised bed combustion (BFBC), also co-firing low and high sulphur content coal with straw or wood.In the large systems the use of both straw and sewage sludge resulted in a small reduction in efficiency (compared with systems using only coal as fuel).In the small-scale systems the high moisture content of the wood chips chosen caused a significant efficiency reduction.Net CO₂ emissions are reduced when biomass is used, and these are compared for the different types and scales of fluidised bed technologies. NO_x emissions were affected by a number of factors, such as bed temperature, amount of sorbent used for SO₂ capture and HCl emitted.     

Co-gasification of meat and bone meal with coal in a fluidised bed reactor

After the Bovine Spongiform Encephalopathy illness appeared, the meat and bone meat (MBM) produced from animal residues became an important waste. In spite of being a possible fuel due to its heating value (around 21.4 MJ/kg), an important fraction of the meat and bone meal is being sent to landfills. The aim of this work is to evaluate the co-gasification of low percentages of meat and bone meal with coal in a fluidised bed reactor as a potential waste management alternative. The effect of the bed temperature (800-900 °C), the equivalence ratio (0.25-0.35) and the percentage of MBM in the solid fed (0-1 wt.%) on the co-gasification product yields and properties is evaluated. The results show the addition of 1 wt.% of MBM in a coal gasification process increases the gas and the liquid yield and decreases the solid yield at 900 °C and 0.35 of temperature and equivalence ratio operational conditions. At operational conditions of 900 °C and equivalence ratio of 0.35, the specific yield to gas (y_gas) increases from 3.18 m³(STP)/kg to 4.47 m³(STP)/kg. The gas energy yield decreased 24.1% and the lower heating value of the gas decreases from 3.36 MJ/m³(STP) to 2.16 MJ/m³(STP). The concentration of the main gas components (H₂, CO and CO₂) hardly varies with the addition of MBM, however the light hydrocarbon concentrations decrease and the H₂S concentration increases at the higher temperature (900 °C).     

Combustion of oil palm stone in a pilot-scale fluidised bed reactor

Biomass is being generated in vast amounts from oil palm plantations particularly in developing countries such as Malaysia, Thailand and Indonesia. Oil palm stone (OPS) is currently considered a waste material and has not previously been considered for energy purposes. The main objective of this study was to investigate the thermochemical conversion of OPS in a pilot-scale fluidised bed combustor. The net heating value of OPS was 24.93 MJ/kg. The effect of primary air flowrate and initial bed temperature were the main parameters investigated. The bed and bed's surface temperature were found to decrease as the primary air flowrate increased. In all tests CO emissions were less than 0.2%. The emissions of SO₂ and HCl ranged from 0.02 ppm to 0.05 ppm, significantly below the permitted levels set by legislation. Stable combustion was observed at a bed temperature of 950 °C. The most abundant elements found in the ash were Al, Ca, Fe, K, Mg, Mn, P, S and Si. However, due to the temperature regime used in the study fouling would not be an issue.     

Discrete element modelling of fluidised bed spray granulation

A novel discrete element spray granulation model capturing the key features of fluidised bed hydrodynamics, liquid-solid contacting and agglomeration is presented. The model computes the motion of every individual particle and droplet in the system, considering the gas phase as a continuum. Microscale processes such as particle-particle collisions, droplet-particle coalescence and agglomeration are directly taken into account by simple closure models. Simulations of the hydrodynamic behaviour of a batch granulation process are presented to demonstrate the potential of the model for creating insight into the influence of several key process conditions such as fluidisation velocity, spray rate and spray pattern on powder product characteristics.     

Numerical simulation of coal gasification at circulating fluidised bed conditions

This paper presents modelling results for a new pressurised fluidised bed gasifier concept, called the Power High-Temperature Winkler gasifier (PHTW gasifier). The numerical simulation of the steam/oxygen blown and lignite-fuelled power plant gasifier is performed on the 4800 t/day (1000 MW) at a pressure of 33 bar. The formation of flow pattern, turbulence, product gas composition, temperature, and radiation heat transfer were investigated. Influence of diameter variation on the flow patterns at constant operating conditions is presented. A comparison between the calculation and literature data of similar fluidised bed systems shows good conformance. To anticipate the solid's behaviour, particle concentration, particle size change due to pyrolysis and surface reactions, and particle tracks were modelled using an Eulerian–Lagrangian approach. While varying the total particle mass flow, the pressure drop as a function of reactor height was observed.     

Co-combustion of coal and biomass in a circulating fluidized bed combustor

In this research, co-combustion of coal and rice husk was studied in a circulating fluidized bed combustor (CFBC). The effects of mixed fuel ratios, primary air and secondary air flow rates on temperature and gas concentration profiles along riser (0.1 m inside diameter and 3.0 m height) were studied. The average particle size of coal from Maetah used in this work was 1,128 mm and bed material was sand. The range of primary air flow rates was 480–920 l/min corresponding to U _g of 1.0–2.0 m/s for coal feed rate at 5.8 kg/h. The recirculation rate through L-valve was 100 kg/hr. It was found that the temperatures along the riser were rather steady at about 800–1,000 degrees Celsius. The introduction of secondary air improved combustion and temperature gradient at the bottom of the riser, particularly at a primary air flow rate below 1.5 m/s. Blending of coal with biomass, rice husk, did improve the combustion efficiency of coal itself even at low concentration of rice husk of 3.5 wt%. In addition, the presence of rice husk in the feed stocks reduced the emission of both NO _x and SO₂.     

Modelling and simulation of coal gasification process in fluidised bed

A one-dimensional steady state mathematical model and a numerical algorithm have been developed to simulate the coal gasification process in fluidised bed. The model incorporates two phases, the solid and the gas. The gaseous phase participates in the emulsion (with the solid phase) and forms the bubble. The solid phase is composed of carbonaceous material, limestone and/or inert bed material. The model can predict temperature, converted fraction, and particle size distribution for the solid phase. For the gaseous phase, in both emulsion and bubble, it can predict profiles of temperature, gas composition, velocities, and other fluid-dynamic parameters. In the feed zone, a Gaussian distribution for the solid particle size is considered. This distribution changes due to attrition, elutriation, consumption and drag inside the reactor. A system of 29 differential and 10 non-linear equations, derived from the mass, energy and momentum balances for each phase, at any point along the bed height, are solved by the Gear and Adams Method. Experimental data from the Universidad de Antioquia and Universidad Nacional-Medellin have been used to validate the model. Finally, the model can be used to optimise the gasification process by varying several parameters, such as excess of air, particle size distribution, coal type, and geometry of the reactor.     

PCDD/PCDF emissions from co-combustion of coal and PVC in a bubbling fluidised bed boiler

This paper reports on the results obtained in the study of the co-combustion of PVC with hard coal from South Africa in a 0,5 MW_th Bubbling Fluidised Bed Boiler. The research has included the study of the effect of combustion temperature, fluidisation velocity and PVC content. The addition of urea to the raw fuel, as a dioxin-preventing compound has also been evaluated. Results have been analysed in terms of combustion efficiency, major pollutants emission (NO_x, CO), and PCDD/Fs formation in the flue gas and in the fly ash. Under the experimental conditions tested, co-combustion of coal and PVC has proved to be feasible from the combustion efficiency and emission of PCDD/Fs points of view, whose levels remained below limits set by existing legislation on persistent organic pollutants. The addition of solid urea to the fuel blend reduces the amount of chlorinated compounds emitted. However, it has a negative impact on nitrogen pollutants formation     

Measurements of dioxin emissions during co-firing in a fluidised bed

The emissions of dioxins could be considerable when fuels with high chlorine content are used, particularly in fluidised beds due to constraints to use temperatures in the range 800-900 °C for other considerations. However, mixing of fuels with different characteristics may lead to a reduction in dioxin emissions. Studies are currently being undertaken at the above-mentioned department in mixing fuels of varying chlorine and sulphur contents to monitor the emissions of dioxins both in the gas and solid phases. Furthermore, the influence of certain elements like Cu in the ash in the emissions of dioxins is also studied to verify the catalytic effect.The INETI pilot-scale test facility is used for the combustion work. Two different coals, namely Colombian and Polish, are used as the base fuel. The supplementary fuels for co-firing include MBM and straw pellets. The combustion temperature is maintained at about 800-830 °C range without any limestone addition. The residence time of over 2 s is respected.Results obtained by far suggest that the presence of sulphur in both fuels have a very strong effect on the eventual emissions of dioxins and the synergy regarding to reduce the dioxins below the levels permitted is possible by mixing fuels based on their characteristics. The paper reports the results obtained and evaluates the effect of fuel nature and operating conditions on the emissions of dioxins.     

Co-combustion of peach and apricot stone with coal in a bubbling fluidized bed

In this study a bubbling fluidized bed combustor (BFBC) having an inside diameter of 102 mm and a height of 900 mm was used to investigate the co-combustion characteristics of peach and apricot stones produced as a waste from the fruit juice industry with coal. A lignite coal was used for co-combustion. On-line concentrations of O₂, CO, CO₂, SO₂, NO_X and total hydrocarbons (C_mH_n) were measured in the flue gas during combustion experiments. Variations of emissions of various pollutants were studied by changing the operating parameters (excess air ratio, fluidization velocity, and fuel feed rate). Temperature distribution along the bed was measured with thermocouples.     

Continuous toluene vapour photocatalytic deduction in a multi-stage fluidised bed

Continuous deduction of 1000 ppm toluene vapour in a multi-stage gas fluidised bed photoreactor was studied using TiO₂ coated activated carbon (AC/TiO₂) particles as the fluidising media. Due to the enrichment of the local toluene concentration, the efficiency of the toluene removal from the gas stream by the mass transfer-limited photocatalytic reaction was significantly improved using AC/TiO₂ particles as the fluidising media. In the stage addition studies, the results showed that the toluene removal efficiency at steady state increased approximate 3-4% for every stage addition. The three-stage design effectively utilised the freeboard region and improved the toluene removal efficiency for approximately 37% when comparing to the single-stage system. Using SiO₂ powders as fluidising media could enhance the light utilisation by light scattering and promotes the toluene deduction during the initial to steady toluene deduction period.     

Co-combustion of Korean anthracite with bituminous coal in two circulating fluidized bed combustors

The co-combustion characteristics for Korean anthracites and bituminous coals were determined in a lab-scale CFB reactor and the commercial scale Tonghae CFB Power Plant. In the lab-scale CFB combustion tests, the effluent rate of the emission gases, which can indicate the reactivity of the combustion, did not change appreciably when each coal burned. As the bituminous coal was added, however, the effluent rate of the emissions increased. The amount of the unburned carbon in ash decreased with increasing the ratio of the bituminous coal during the co-combustion. When the co-combustion was tested in the Tonghae CFB power plant, the temperatures at the upper part of the combustor and the cyclones, which were somewhat higher than designed and expected, could be reduced as the bituminous coal ratio increased. Consequently, more stable operation of the CFB boiler was achieved. The efficiency of the CFB boiler also increased due to increasing the reactivity of the combustion. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Agglomeration in fluidised bed gasification of biomass

Three promising biomass fuels for southern Mediterranean regions were tested for their agglomeration tendency in an atmospheric lab-scale fluidised bed (FB) gasifier using quartz and olivine as bed materials. The defluidisation temperatures of the energy crops Giant Reed (Arundo donax L.) and Sweet Sorghum bagasse were respectively approx. 790 °C and 810 °C, in both bed materials, while the agro industrial residue olive bagasse caused defluidisation of the quartz bed at 830 °C and olivine bed at > 850 °C. Agglomerates from these tests were analysed with SEM/EDS. Coatings and necks between bed particles were formed due to ash derived potassium silicate melt. For the first two fuels cluster-type agglomerates around remains of char particles were observed. Thermodynamic equilibrium simulations of each chemical system were performed to cross examine the predicted ash melting temperatures and chemistry with experimental findings. Predictions of potassium liquid compounds, like K₂O·SiO_2(l) were verified by EDS analyses on the particle coatings. FB gasification of olive bagasse resisted defluidisation up to higher temperatures because of its lower potassium and higher calcium content, especially in the case of olivine bed. The latter experimental finding coincided with thermodynamic predictions.     

Study on the structure and gasification characteristics of selected South African bituminous coals in fluidised bed gasification

The gasification characteristics of three South African bituminous coals were investigated in a bubbling fluidised bed reactor. The three coals are similar in rank, but two are inertinite-rich coals and the third has a high vitrinite content. The microstructural characteristics of the parent coals and their resultant chars were determined using XRD, FT-IR, Raman and petrographic analysis. The microstructural changes that occurred in the organic (maceral) and the inorganic (mineral) fractions of the selected coals were evaluated. The change in the carbon structure was correlated to the proportions of inertinite and vitrinite macerals in the coals. High vitrinite content resulted in an increase in the order of the disordered carbon structure after gasification and this leads to greater graphitised ordered carbon structures. While a high inertinite content resulted in low or no structural transformation of the chemical structure. The transformation of inorganic mineral constituents of the coal was correlated to the amount of inertinite present in the selected coals. Higher proportions of inertinite macerals and inertinitic chars resulted in higher proportions of melted minerals. Char samples with low proportions of organic matter resulted in higher proportion of melted minerals covering the char surface.     

Online measurement and control of solids moisture in fluidised bed dryers

Currently, two main methods are used to take online measurement of the solids moisture in fluidised bed dryers, namely microwave resonance and near infrared spectroscopy. In this paper, a new online approach to solids moisture measurement of batch fluidised bed dryers by electrical capacitance tomography (ECT) is presented for the first time. Based on online measurement of solids moisture, it is possible to implement feedback control and process optimisation of batch fluidised bed drying processes, aiming to increase the operation efficiency and to improve product quality. A twin-plane ECT sensor with eight electrodes in each plane is mounted in the bottom of a glass fluidisation chamber. From the adjacent electrode pairs, the water content of the solids is estimated based on the correlation between the moisture content and the permittivity value. To reduce measurement error, the effect of temperature on moisture measurement is compensated. The fluidisation velocity is estimated by a semi-empirical function based on the measured water content. The acquired information is sent to a controller to adjust the air flow rate of the fluidised bed dryer. To validate the moisture measurement by ECT, a mathematical model has been developed, based on the measured temperature and relative humidity of the outlet air. The Landweber iteration method is applied to reconstruct images. The averaged solids concentration along the radial direction at different fluidisation conditions is given and compared with results by the linear back-projection (LBP) method. Results from batch drying processes with online measurement and feedback control are given and compared with no feedback control. To compare the operation efficiency, the thermal efficiency is considered and the results show the possibility of online control and optimisation of the fluidised bed drying processes, based on online measurement of solids moisture by ECT. Some challenges and future work are discussed.     

Kinetics of fluidised bed melt granulation III: Tracer studies

Previous work (Proceedings of World Congress on Particle Technology, Sydney 2002, 629-636.) has shown that granule breakage occurs during fluidised bed melt granulation (FBMG) and should not be neglected when it comes to addressing granulation kinetics. In the current work, we have developed and verified tracer experiments in FBMG, in an attempt to decouple the influence of granule size and age on breakage kinetics. The tracer data during granulation shows that granule breakage is occurring at a much slower rate than aggregation, while the breakage-only tracer experiments reveal the breakage selection rate to be independent of size at an approximate value of . The observations allow us to deduce that the aggregation rate for smaller granules is actually faster than larger ones during granulation.     

The heat transfer coefficient between a particle and a bed (packed or fluidised) of much larger particles

The heat transfer coefficient has been measured for a heated phosphor-bronze sphere (diam. 2.0, 3.0 or 5.56 mm) added to a bed of larger particles, through which air at room temperature was passed. The bronze heat transfer sphere was attached to a very thin, flexible thermocouple and was heated in a flame to before being immersed in the bed. The cooling of the bronze sphere enabled the heat transfer coefficient, h, to be measured for a variety of U/U_mf, as well as diameters of both the particles in the bed and the heat transfer sphere. It was found that before the onset of fluidisation, h rose with U, but h reached a constant value for U?U_mf. These measurements indicate that in this situation (of a relatively small particle in a bed of larger particles) all the heat transfer is between the hot bronze sphere and the gas flowing over it. Consequently, a Nusselt number, based on the thermal conductivity of the gas, is easy to define and for U?U_mf (i.e. a packed bed), Nu is given by