Synthesis and characterization of polyamides and poly(amide-imide)s based on ether-sulfone-diamines

A series of polyamides and poly(amide-imide)s were prepared by the direct polycondensation of 4,4′-[sulfonylbis(1,4-phenyleneoxy)]dianiline or 4,4′-[sulfonylbis(2,6-dimethyl-1,4-phenyleneoxy)]dianiline with aromatic dicarboxylic acids and phthalimide unit-bearing dicarboxylic acids in a N-methyl-2-pyrrolidone (NMP) solution containing dissolved calcium chloride using triphenyl phosphite and pyridine as condensing agents. The inherent viscosities of the resulting polymers were above 0.45 dL/g and up to 1.70 dL/g. Except for the polyamides derived from terephthalic acid and 4,4′-biphenyldicarboxylic acid, all the other polyamides and all poly(amide-imide)s were readily soluble in polar organic solvents such as NMP, N, N-dimethylacetamide (DMAc), N,N-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), and m-cresol, and afforded transparent and tough films by solution-casting. Most of the polymers showed distinct glass transition on their differential scanning calorimetry (DSC) traces and their glass transition temperatures (T_g) stayed between 140–264 °C. The methyl-substituted polymers showed higher T_gs than the corresponding unsubstituted counterparts. The results of the thermogravimetry analysis (TGA) revealed that all the methyl-substituted polymers showed lower initial decomposition temperatures than the unsubstituted ones.     

Synthesis and characterization of polyimides based on isopropylidene-containing bis(ether anhydride)s

Two bis(ether anhydride)s, 4,4′-[1,4-phenylenebis(isopropylidene-1,4-phenyleneoxy)]-diphthalic anhydride (IV _a) and 4,4′-[isopropylidenebis(1,4-phenylene)dioxy]diphthalic anhydride (IV _b), were prepared in three steps starting from the nucleophilic nitrodisplacement reaction of 4-nitrophthalonitrile with α,α ′-bis(4-hydroxyphenyl)-1,4-diisopropylbenzene (I _a) and 4,4′-isopropylidenediphenol (I _b) in N,N-dimethylformamide (DMF) in the presence of potassium carbonate. The bis(ether anhydride)s IV _a and IV _b were polymerized with various aromatic diamines to obtain two series of poly(ether amic acid)s VI _a–g and VII _a–g with inherent viscosities in the range of 0.30∼0.74 and 0.29∼1.01 dL/g, respectively. The poly(ether amic acid)s were converted to poly(ether imide)s VIII _a–g and IX _a–g by thermal cyclodehydration. Most of the poly(ether imide)s could afford flexible and tough films, and they showed high solubility in polar solvents such as N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide, and m-cresol. The obtained poly(ether imide) films had tensile strengths of 45∼83 MPa, elongations-to-break of 6∼27%, and initial modulus of 0.6∼1.7 GPa. The T_gs of poly(ether imide)s VIII _a–g and IX _a–g were in the range of 194∼210 and 204∼243 °C, respectively. Thermogravimetric analysis (TG) showed that 10% weight loss temperatures of all the polymers were above 500 °C in both air and nitrogen atomspheres.     

Syntheses and properties of polyimides based on bis(p-aminophenoxy)biphenyls

Three biphenyl unit-containing diamines,4,4-bis(p-aminophenoxy)biphenyl (III_a), 2,2-bis(p-aminophenoxy)biphenyl (III_b), and 3,3,5,5-tetramethyl-4,4-bis(p-aminophenoxy)biphenyl (III_c), were prepared by the chlorodisplacement ofp-chloronitrobenzene with 4,4-biphenol (I_a), 2,2-biphenol (I_b), and 3,3,5,5-tetramethyl-4,4-biphenol (I_c), respectively, giving the corresponding bis(nitrophenoxy) compounds II_a-c, followed by catalytic reduction with palladium (Pd) and hydrazine. Three series of polyimidesp-PI,o-PI, and Me-PI were prepared from diamines III_a-c and aromatic tetracarboxylic dianhydrides via a two-stage procedure that included ring-opening polyaddition to give poly(amic acid)s followed by thermal cyclodehydration to polyimides. The resultant three series of poly(amic acid)s had inherent viscosities of 1.09–2.83, 0.78–1.93, and 1.55–3.09 dL/g, respectively. Almost all the poly(amic acid)s could be solution-cast and thermally converted into transparent, flexible, and tough polyimide films. All the polyimides were characterized by solubility, tensile test, wide-angle X-ray scattering measurements, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). Effects of the structures of aromatic diamines and dianhydrides on the properties of polyimides were investigated.     

Synthesis and properties of <Emphasis Type="Italic">ortho</Emphasis>-linked aromatic poly(ester-amide)s and poly(ester-imide)s bearing 2,3-bis(benzoyloxy)naphthalene units

Two new naphthalene-ring-containing bis(ester-amine)s, 2,3-bis(4-aminobenzoyloxy)naphthalene (p-2) and 2,3-bis(3-aminobenzoyloxy)naphthalene (m-2), were prepared from the condensation of 2,3-dihydroxynaphthalene with 4-nitrobenzoyl chloride and 3-nitrobenzoyl chloride, respectively, followed by catalytic hydrogenation. The novel aromatic poly(ester-amide)s and poly(ester-imide)s having 2,3-linked bis(benzoyloxy)naphthalene units have been synthesized from the polycondensation reactions of bis(ester-amine)s (p-2 and m-2) or an equimolar mixture of 4,4′-oxydianiline and p-2 or m-2 with various aromatic dicarboxylic acids and dianhydrides. The synthesis of the poly(ester-amide)s was achieved by the phosphorylation polyamidation reaction by means of triphenyl phosphate, and the synthesis of the poly(ester-imide)s included ring-opening polyaddition to give poly(amic acid)s followed by chemical imidization to polyimides. Most of the poly(ester-amide)s were readily soluble in various organic solvents. Six poly(ester-amide)s and two poly(ester-imide)s derived from less rigid diacids and dianhydrides, respectively, were amorphous and could be solution-cast into transparent and tough films with good mechanical properties. Most of the poly(ester-amide)s displayed discernible glass-transition temperatures (T _gs) between 192 and 223 °C in the DSC traces. All of the poly(ester-imide)s, except for one sample, showed clear T _g values between 225 and 265 °C by DSC. These poly(ester-imide)s showed excellent thermal stability with 10 wt% loss temperatures above 460 °C in nitrogen or air.     

Synthesis and properties of novel aromatic polyimides derived from bis(p-aminophenoxy)methylphenylsilane

A novel siloxane-containing diamine, bis(p-aminophenoxy)methylphenylsilane (BAMPS), was synthesized from the condensation of dichloromethylphenylsilane with p-aminophenol in the presence of triethylamine. A series of BAMPS-based aromatic polyimides were prepared from BAMPS and various aromatic tetracarboxylic dianhydrides by the usual two-step procedure including ring-opening polyaddition to poly(amic acid)s and subsequent cyclodehydration to polyimides. The inherent viscosities of poly(amic acid)s III_a - III_f ranged from 0.09 to 0.36 dL g⁻¹ in N,N-dimethylacetamide at a concentration of 0.5 g dL⁻¹ at 30°C. The inherent viscosities of polyimides were between 0.06 and 0.32 dL g⁻¹ in various solvents at 30°C. Polyimides, especially IV_c and IV_f , were soluble in a wide range of organic solvents such as N-methyl-2-pyrrolidinone, concentrated H₂SO₄, N,N-dimethylacetamide, N,N-dimethylformamide, and dimethyl sulfoxide. The polyimides were characterized by elementary analysis, IR spectra, TGA, and DSC. They also had glass transition temperatures ranging from 128 to 181°C. The 10% mass loss temperature was recorded in the range of 404–443°C in nitrogen and of 315–339°C in oxygen. © 1997 John Wiley & Sons, Inc.     

Polyimides based on furanic diamines and aromatic dianhydrides: synthesis,characterization and properties

Novel polyimides containing furan moieties were prepared from the resulting furanic diamine monomers with various aromatic dianhydrides including 1,2,4,5-benzene-tetracarboxylic dianhydride, 3,3′,4,4′-biphenyltetracarboxylic dianhydride, 4,4′-oxydiphthalic anhydride, and hexafluoroisopropylidene 2,2-bis(phthalic anhydride), via a two-step process. The resulting polyimides were characterized by solubility tests, viscosity measurements, FTIR, ¹H NMR spectroscopy, differential scanning calorimetric (DSC), and thermogravimetric analysis (TGA) analysis. The polyimides with inherent viscosities in the range of 0.048–0.095 L/g showed excellent solubility in aprotic amide and organic solvents, such as N,N-dimethylacetamide, N-methyl-2-pyrrolidinone, dimethylformamide and acetone, chloroform, etc. DSC showed glass transition temperatures (T _g) in the range of 116–143 °C. These polymers showed excellent thermal stability up to 390 °C.     

Aromatic polyesters (polyarylates) containing arylene sulfone ether linkages

A series of soluble aromatic polyesters (polyarylates) containing arylene sulfone ether linkages and having inherent viscosities of 0.36–1.10 dl/g were prepared by the two-phase low temperature polycondensation of 4,4′-[sulfonyl-bis(p-phenyleneoxy)]dibenzoyl chloride and 3,3′-[sulfonylbis(p-phenyleneoxy)]-dibenzoyl chloride with various bisphenols in an organic solvent-aqueous alkaline solution system in the presence of a phase transfer catalyst. Bisphenols 4,4′-[sulfonylbis(p-phenyleneoxy)]diphenol and 3,3′-[sulfonylbis(p-phenyleneoxy)]-diphenol were synthesized in quantitative yields by an improved procedure. The aromatic polyesters prepared were characterized by infrared spectroscopy, elemental analysis, solution viscosity, thermogravimetric analysis, differential scanning calorimetry and X-ray diffraction. The polyesters prepared had glass transition temperatures in the range 150–230°C and initial decomposition temperatures of 397–491°C. They gave transparent, tough and flexible films by the solution casting technique.     

Heat stable and organosoluble polyimides containing laterally-attached phenoxy phenylene groups

In this research a diamine monomer containing two phenoxy phenylene lateral groups, 2,2′-bis[(p-phenoxy phenyl)]-4,4′-diaminodiphenyl ether (PPAPE) was used to prepare novel wholly aromatic polyimides by thermal or chemical two-step polycondensation reactions. Comonomers including pyromellitic dianhydride (PMDA), 4,4′-oxydiphthalic anhydride (ODPA), and 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA) were used for the polyimidization reactions. A reference polyimide was also prepared by the reaction of 4,4′-diaminodiphenyl ether (DADPE) with pyromellitic dianhydride (PMDA). The limited viscosity numbers as well as [`(M)]<sub>n</sub> \overline{M}_n and [`(M)]_w \overline{M}_w values of the resulting polymers were determined. All PPAPE-resulted polyimides had excellent organosolubility in common polar solvents. A low crystallinity extent was only observed using their wide-angle X-ray diffractograms (WAXD). The prepared hinged polyimides could also be cast into transparent and flexible films. The glass transition temperatures of the resulting polyimides were determined by differential scanning calorimetry (DSC) analyses. The thermograms obtained from thermogravimetric analyses (TGA) showed that the phenoxy phenylene lateral groups attached to the macromolecular backbones had no substantial diminishing effect on the thermal stability of these structurally-modified polyimides.     

Structure–property relationships for partially aliphatic polyimides

The structure–property relationship was studied for partially aliphatic polyimides containing alicyclic dianhydride and aromatic diamine unit. Rel-[1S,5R,6R]-3-oxabicyclo[3,2,1]octane-2,4-dione-6-spiro-3′-(tetrahydrofuran-2′,5′-dione) (DAn) was used as an unsymmetrical spiro dianhydride, and 1,2,3,4-cyclopentanetetracarboxylic dianhydride (CPDA) and bicyclo[2.2.2]oct-7-ene-2,3,5,6-tetracarboxylic dianhydride (BOCA) were used as symmetrical non-spiro dianhydrides. The dianhydrides were polymerized with two aromatic diamines, 4,4′-oxydianiline (ODA) and 4,4′-(hexafluoroisopropylidene)dianiline (FDA), using a conventional two-step chemical imidization method. Structures of the PAl-PIs prepared were confirmed by ¹H-NMR and FT-IR spectroscopy. Solubility of the polyimides was tested in various organic solvents. Thermal properties of the PAl-PIs were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). UV-visible spectroscopy was performed to evaluate the optical transparency of the polyimides. The effect of monomer structure on the properties was studied. The PAl-PIs prepared from DAn showed improved solubility, thermal properties, and transparency when compared with PAl-PIs derived from CPDA and BOCA. It is considered that the rigid, unsymmetrical spiro structure of DAn leads to rigidity, bulkiness, irregularity, and non-linearity of the polyimide chains, resulting in the enhanced properties of DAn polyimides. The molecular arrangement in the polyimides has also been studied by wide-angle X-ray diffraction (WAXD) and was correlated with the properties.     

Synthesis and characterization of new optically active and photolable poly (amide-imide)s from N,N ′-(3,3′,4,4′-benzophenonetetracarboxylic)-3,3′,4,4′-diimido-di-L-methionine and different diamines

Summary N,N^′-(3,3^′,4,4^′-benzophenonetetracarboxylic)-3,3^′,4,4^′-diimido-di-L-methionine (3) was prepared from the reaction of 3,3^′,4,4^′-benzophenonetetracarboxylic-3,3^′,4,4^′-dianhydride (1) with L-methionine (2) in a solution of (glacial acetic acid/pyridine) at refluxing temperature. The phosphorylation polycondensation of the diimide-diacid monomer (3) with 1,3-phenylenediamine (4a), 1,4-phenylenediamine (4b), 2,6-diaminopyridine (4c), 3,5-diaminopyridine (4d), 4,4^′-diaminobiphenyl (4e) and 4,4^′-diaminodiphenylsulfone (4f) was carried out in N-methyl-2-pyrolidone (NMP). The resulting poly (amide-imide)s showed admirable moderate inherent viscosities (0.23–0.48 dl g^-1), good thermal stability and improved optical activity. All of the above compounds were fully characterized by IR spectroscopy, elemental analysis and specific rotation. Some structural characterization and physical properties of these new poly (amide-imide)s are presented.     

Synthesis and characterization of polyamides based on cubane-1,4-dicarboxylic acid

The direct polycondensations of cubane-1,4-dicarboxylic acid with 1,4-phenylenediamine (2 a), 4,4′-oxydianiline (2 b), 4,4′-sulfonyldianiline (2 c), and 9,9′-bis(4-aminophenyl)florene (2 d) were carried out in N-methyl-2-pyrrolidone/pyridine containing triphenylphosphite and lithium chloride at 110 °C for 9 h. Polyamide 3 a obtained from 2 a was scarcely soluble in organic solvent even during heating, and was soluble only in conc-H₂SO₄, whereas 3 c and 3 d derived from 2 c and 2 d, respectively, were readily soluble in N-methyl-2-pyrrolidone, N,N-dimethylacetamide, N,N-dimethylformamide, and dimethylsulfoxide. After treating polyamide 3 d with the rhodium complex catalyst in NMP, cubane units were quantitatively converted into cyclooctatetraenes. Received: 3 March 1997/Accepted: 1 April 1997     

Synthesis of poly(ethyl vinyl ethers) containing two dipolar electronic systems and their properties

Summary 5-Nitro-2-(2′-vinyloxyethoxy)benzylidenemalononitrile (2a), methyl 5-nitro-2-(2′-vinyloxyethoxy)benzylidenecyanoacetate (2b), 3-nitro-4-(2′-vinyloxyethoxy)benzylidenemalononitrile (4a), and methyl 3-nitro-4-(2′-vinyloxyethoxy)benzylidenecyanoacetate (4b) were prepared by the condensation of 5-nitro-2-(2′-vinyloxyethoxy)benzaldehyde (1) and 3-nitro-4-(2′-vinyloxyethoxy)benzaldehyde (3) with malononitrile or methyl cyanoacetate, respectively. Vinyl ether monomers 2a-b and 4a-b were polymerized with boron trifluoride etherate as a cationic initiator to yield poly(vinyl ethers) 5-6 having nitrooxybenzylidenemalononitrile and nitrooxycyanocinnamate, which is effective chromophore for second-order nonlinear optical applications. Polymers 5-6 were soluble in common organic solvents such as acetone and DMSO. T _g values of the resulting polymer were in the range of 70–81°C. Electrooptic coefficient (r₃₃) of the poled polymer films were in the range of 19–27 pm/V, which was improved by introducing of nitro group. Polymers 5–6 showed a thermal stability up to 300°C in TGA thermograms, which is acceptable for NLO device applications. Received: 24 November 1998/Revised version: 19 January 1999/Accepted: 29 January 1999     

Novel Ferrocene-Based Organometallic Poly(ether sulfone amide imide)s: Preparation, Characterization, and Properties

A new ferrocene-based diamine (ESAFDA) with built-in ether, sulfone, and amide groups was prepared via reaction of two synthetic precursors. Firstly, 1,1′-ferrocenedicarbonyl chloride was prepared from 1,1′-ferrocenedicarboxylic acid using oxalyl chloride. In another reaction, nucleophilic substitution reaction of 3-aminophenol with bis(4-chlorophenyl sulfone) was used for synthesis of 3,3′-(4,4′-sulfonyl bis(1,4-phenylene) bis (oxy)) dianiline (SBOD). Finally, the diamine was prepared via nucleophilic reaction of SBOD with 1,1′-ferrocenedicarbonyl chloride. The precursors and the diamine were characterized by conventional methods and the diamine was used for preparation of different ferrocene-based poly(ether sulfone amide imide)s through polycondensation with three different dianhydrides. The polymers were characterized by elemental analysis, FTIR and ¹H-NMR spectroscopy. Various properties of the polymers including inherent viscosity, molecular weight, solubility, thermal stability and behavior, flame-retardant nature, mechanical properties, and crystallinity were studied. Presence of ferrocene structure in companion to ether, sulfone, and amide units in the backbone of polyimides led to improved solubility of the polymers in polar aprotic solvents and enhanced thermal stability and flame-retardant character of polyimides.     

Synthesis and properties of organosoluble polyimides based on novel flourene‐ring containing diacetamido‐diamine

A new diacetamido‐diamine monomer, N′‐[7‐(acetyl‐4‐aminoanilino)‐9,9‐dioctylflouren‐2‐yl]‐N′‐4‐aminophenyl) acetamide (ADOAc), with flourene‐based structure was prepared from the reaction of 4‐aminoacetanillide with 2,7‐dibromo‐9,9‐dioctylfluorene in the presence of 10 mol % CuI, 20 mol % N,N′‐dimethylethylene diamine as catalyst and K₂CO₃ as base. Two new flourene‐ring containing polyimides were prepared from the reaction of ADOAc with aromatic dianhydrides such as pyromellitic dianhydride (PMDA) and 3,3′,4,4′‐benzophenonetetracarboxylic dianhydride (BTDA) via chemical imidization of poly(amic acid). The new diamine and the related polyimides were characterized by using conventional methods such as FT‐IR, NMR, and elemental analysis. The polyimides obtained from the reaction of ADOAc with PMDA (PIa) and of ADOAc with BTDA (PIb) had inherent viscosity of 0.49 and 0.58 dL/g respectively, and showed excellent solubility in a variety of organic solvents. The polyimides of PIa and PIb showed excellent thermal stability with 10% weight loss in nitrogen atmosphere at temperatures of 418°C and 407°C and T_g of 172°C and 167°C, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and Properties of Polyimides Based on an Ether Ketone Diamine, 4,4'-Bis(4-aminophenoxy)benzophenone

A diamime monomer with ether-ketone group, 4,4'-Bis(4-aminophenoxy)benzophenone (II) was prepared through the nucleophilic substitution reaction of 1-chloro-4-nitrobenzene with 4,4'-Dihydroxybenzophenone in the presence of potassium carbonate in N,N-dimethylformamide, followed by catalytic reduction with hydrazine and Pd/C. Polyimides (PI) V _a–f (H), V _a–f (C) and copolyimides (co-PI) V _{b–d/m(e–f)} were synthesized from II and six kinds of commercial aromatic dianhydrides (III _a–f )via thermal or chemical imidization method. Poly(amic acid) (IV _a–f )had inherent viscosities range from 0.81 to 0.98 dL/g. PI of thermal imidization method was showed poor solubility even sulfuric acid. But PI of chemical imidization method V _e,f (C) and (co-PI(C)) could be dissolved. The reason is that the ketone group of poly(amic acid) segments linked with the terminal amino group of polymer chains during thermal imidization. PI films V _a–f (H) had tensile strengths of 101–118 MPa, elongations to break of 11–32%, and initial moduli of 2.1–2.8 GPa. The glass transition temperatures of V series were in the range of 252–278°C, and the temperatures of 10% weight loss (T ₁₀) were above 529°C and their residues more than 50% at 800°C in nitrogen. V series also measured the color, dielectric constants and moisture absorptions. Their films had cutoff wavelengths between 378–421 nm, b ^* values ranging from 16.4 to 77.1, dielectric constants of 3.47–3.85 (1 MHz), and moisture absorptions in the range of 0.31–0.46 wt%.     

Imide-to-benzoxazole rearrangement in ortho substituted poly(4-4'-diphenylene pyromellitimide)s

Summary Ortho substituted poly(4,4'-diphenylene pyromellitimide)s were prepared from pyromellitic dianhydride and 3,3′-dihydroxybenzidine or 3,3′-dimethoxybenzidine. Thermal cyclodehydration of the corresponding poly(amic acid)s, PAA, led to the formation of ortho-hydroxy- or o-methoxy-polyimides, while catalytic imidization in the presence of aliphatic anhydrides was accompanied by acylation of the OH groups resulting in the formation of lateral acetoxy substituents. The direction of the latter reaction was controlled by the acidity of dehydration agents and the use of a catalyst. Imidization in the presence of acetic anhydride and pyridine led to poly[(3,3'-diacetoxy-4,4'-diphenylene)pyromellitimide] and the use of trifluoroacetic anhydride resulted in the formation of the corresponding polyisoimide with ortho-trifluoroacetoxy groups. This polyisoimide was completely soluble in amide solvents above 60°C. The polymers were studied by FTIR spectroscopy, TGA, and WAXS. It was found that ortho substituents such as OH and methoxy groups could react with the imide cycle above 350°C causing its rearrangement to benzoxazole. The formation of notable amounts of benzoxazole was also observed for o-acetoxy polyimides. Received: 20 November 2001/Revised version: 19 March 2002/ Accepted: 19 March 2002     

Preparation and characterization of organosoluble polyimides based on 1,1-bis[4-(3,4-aminophenoxy)phenyl]cyclohexane and commercial aromatic dianhydrides

A bis(ether amine) III-A containing a cyclohexane cardo group, 1,1-bis[4-(4-aminophenoxy)phenyl]cyclohexane, was synthesized and used as a monomer to prepare polyimides VI-A with six commercial dianhydrides via three different procedures. The intermediate poly(amic acid)s had inherent viscosities of 0.83–1.69 dL g⁻¹ and were thermally or chemically converted into polyimides. Polyimides were also prepared by high-temperature direct polymerization in m-cresol and had inherent viscosities higher than the thermally or chemically cyclodehydrated ones. To improve the solubility of polyimides, six copolyimides were also synthesized from bis(ether amine) III-A with a pair of dianhydrides, which contained 3,3′,4,4′-diphenylsulfonetetracarboxylic dianhydride or 4,4′-hexafluoroisopropylidenediphthalic anhydride. Series VI-A polyimides were characterized by the good physical properties of their film-forming ability, thermal stability, and tensile properties. A comparative study of the properties, with the corresponding polyimides derived from 2,2-bis[4-(4-aminophenoxy)phenyl]propane, is also presented. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2750–2759, 2001     

Organosoluble and Light-colored Fluorinated Polyimides from 2,2-Bis[4-(4-amino-2-trifluoromethylphenoxy)phenyl]sulfone and Aromatic Dianhydrides

A new trifluoromethyl-substituted diamine monomer, 2,2-bis[4-(4-amino-2-trifluoromethylpenoxy)phenyl]sulfone (II), was prepared through the nucleophilic substitution reaction of 2-chloro-5-nitrobenzotrifluoride and 4,4’-sulfonyl diphenol in the presence of potassium carbonate, followed by catalytic reduction with hydrazine and Pd/C. Novel fluorinated polyimides V_a–f having inherent viscosities ranging from 0.74 to 1.14 dL/g were synthesized from the diamine II with various aromatic dianhydrides via thermal imidization of poly(amic acid). Most of V series were soluble in the all test solvents, except V_b(H). These polyimide films had strengths at yield of 94–119 MPa, tensile strengths of 90–118 MPa, elongations to break of 10–16%, and initial moduli of 2.0–2.4 GPa. The glass transition temperature (T_g) of these polymers were in the range of 244–297 ^○C, their 10% weight loss temperatures were above 520 ^○C under ether nitrogen or air atmosphere, and left more than 45 wt% residue even at 800 ^○C in nitrogen. Compared with polyimides VII based on 4,4’-bis(3-aminophenoxy)diphenyl sulfone (II’), V showed better solubility and lower color intensity, dielectric constant, and moisture absorption. Their films had cutoff wavelengths between 355–402 nm, b^* values ranging from 6.8 to 32.9, dielectric constants of 3.32–4.27 (1 MHz), and moisture absorptions in the range of 0.27–0.62 wt%.     

Soluble polyimides with propeller shape triphenyl core for membrane based gas separation

This article reports the synthesis and characterization of a series of new aromatic polyimides (PIs) having bulky tert butyl group containing propeller shaped triphenylamine unit in its structure. The PIs were prepared by the reaction of 4,4′‐diamino‐4″‐(2,4,6‐tri‐tert‐butylphenoxy) triphenylamine with different commercially available aromatic dianhydrides through the formation of corresponding poly(amic acid)s and subsequent thermal cycloimidization. The PIs showed high glass transition temperature (T_g up to 270 °C) and thermal stability (T_d10 up to 475 °C). The PI membranes showed good mechanical properties with tensile strength up to 70 MPa, excellent separation performance [P(CO₂) = 100.8, P(O₂) = 40.4 barrer], and good permselectivity [P(CO₂)/P(CH₄) = 50.9, P(O₂)/P(N₂) = 7.6]. The membranes exhibited extremely high solubility selectivity for the CO₂/CH₄ gas pair due to the strong affinity between CO₂ and nitrogen atoms of tertiary amine in triphenylamine. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46658.     

Synthesis and property measurements of polyimides with substituted pyromellitic dianhydride for flexible printed circuits applications

Pyromellitic dianhydride‐based dianhydrides with bulky substituents, such as 1‐phenyl pyromellitic dianhydride and 1‐(4′‐trifluoromethylphenyl)pyromellitic dianhydride, were combined with bis(3‐aminophenyl)phenylphosphine oxide and 4,4′‐phenylene diamine to prepare polyimides with low coefficient of thermal expansion (～ 17 ppm/°C) and good adhesion (>100 g/mm). The polyimides were synthesized via a conventional two‐step process: preparation of poly(amic‐acid) followed by solution imidization with o‐dichlorobenzene. The molecular weights of the polyimides were controlled to 25,000 g/mol via off‐stoichiometry and the synthesized polyimides were characterized by Fourier transform infrared, nuclear magnetic resonance, differential scanning calorimetry, and thermogravimetric analysis. Their intrinsic viscosity and solubility were also measured, while adhesive property was measured via T‐peel test samples of Cu/polyimide. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010