Friction and Wear Behaviors of Ag/MoS2/G Composite in Different Atmospheres and at Different Temperatures

Silver-based composite with 15?vol% MoS₂ and with 5?vol% graphite was prepared by powder metallurgy method. The impacts of the counterface materials, atmosphere, and temperature on the tribological behavior of the composite were investigated. It was found that when sliding against brass less effective lubricating film formed, causing a higher friction and wear comparing with ASTM-1045 steel. With the increasing proportion of oxygen in the O₂/N₂ atmosphere, the wear rate and friction coefficient ascended slightly. At 200?°C, the combination lubrication of graphite, MoS₂, and Ag contributed to a low friction coefficient (0.07) and wear rate (6.56?×?10^?6?mm³/Nm). At 400?°C, graphite lost its lubricating role, while silver became excessively soft. Large amount of MoS₂ was oxidized into MoO_3, and the residual MoS₂ formed some island-like lubricating films. Severe adhesive wear occurred on the contact surface, which led to a high friction coefficient (0.25) and a great increase of the wear rate (23.2?×?10^?6?mm³/Nm). At 600?°C, a relatively low friction coefficient (0.1) was obtained because of the formation of high-temperature solid lubricants, (Ag₂Mo₄O₁₃ and Ag₂Mo₂O₇) and liquid Ag₂Mo₂O₇. However, the wear rate at 600?°C was the highest (32.6?×?10^?6?mm³/Nm) due to the thick transfer layer.     

Vacuum tribological behaviour of self‐lubricating quasicrystalline composite coatings

High‐temperature‐resistant self‐lubricating coatings are needed in space vehicles for components that operate at high temperatures and/or under vacuum. Thick composite lubricant coatings containing quasicrystalline alloys as the hard phase for wear resistance can be deposited by a thermal spray technique. The coatings also contain lubricating materials (silver and BaF₂ CaF2 eutectic) and NiCr as the tough component. This paper describes the vacuum tribological properties of TH103, a coating of this type, with a very good microstructural quality. The coating was deposited by high‐velocity oxygen fuel spraying and tested under vacuum using a pin‐on‐disc tribometer. Different loads, linear speeds, and pin materials were studied. The pin scars and disc wear tracks were characterised using a combination of scanning electron microscopy and energy dispersive spectrometry. A minimum mean steady friction coefficient of 0.32 was obtained when employing an X750 Ni superalloy pin in vacuum conditions under 10 N load and 15 cm/s linear speed, showing moderate wear of the disc and low wear of the pin.     

Tribological characteristics of magnetron sputtered MoS2 films in various atmospheric conditions

The friction and wear behaviors of magnetron sputtered MoS₂ films were investigated through the use of a pin and disk type tester. The experiments were performed for two kinds of specimens (ground (Ra 0.5μm) and polished (Ra 0.01 μm) substrates) under the following operating condifions: linear sliding velocities in the range of 22 -66 mm/s(3 types), normal loads varying from 9.8-29.4 N(3 types) and atmospheric conditions of air, medium and high vacuum(3 types). Silicon nitride pin was used as the lower specimen and magnetron sputtered MoS₂ on bearing steel disk was used as the upper specimen. The results showed that low friction property of the MoS₂ films could be identified in high vacuum and the specific wear rate in air was much higher than that in medium and high vacuum due to severe oxidation. It was found that the main wear mechanism in air was oxidation whereas in high vacuum accumulation of plastic flow and adhesion, were the main causes of wear.     

The Effects of Dopants on the Chemistry and Tribology of Sputter-Deposited MoS2 Films

The fact. that dopants improve the friction and wear properties of sputtered MoS₂ films is well known. However, the role of dopants in the mechanisms governing friction and wear are not well understood. The purpose of this work is to gain a fundamental understanding of their role by co-depositing a number of materials, i.e., Ni, Fe, Au, and. Sb₂O₃, with MoS₂ and evaluating their effects on film chemistry, crystallinity, microstructure, and tribology. Friction and wear measurements were collected, using ball-on-flat and dual-rub shoe tribom-eters. Other physical and chemical properties were obtained using SEM, XPS, XRD) and Raman spectroscopy. Crystalline MoS₂ was seen in all of the films. In Sb₂O₃-doped films, an amorphous phase was also observed. The presence of dopants caused film densification and affected crystallite size. They had little effect on the overall crystallite orientation. In addition, dopants caused a reduction in the mean and. variance of the friction coefficient and an increase in wear life. The correlation between dopants, film properties, and tribology is discussed in detail.     

Effect of the Synergetic Action on Tribological Characteristics of Ni-Based Composites Containing Multiple-Lubricants

Ni-based self-lubricating composites with multiple-lubricants addition were prepared by a powder metallurgy technique, and the effect of multiple-lubricants on tribological properties was investigated from room temperature to 700?°C. The synergetic effects of graphite, MoS₂, and metallic silver lubricants on the tribological characteristics of composites were analyzed. XRD analysis showed that new Cr _x S _y and Mo₂C phase were formed in the composites containing graphite, MoS₂ and metallic Ag lubricants during the sintering process. The average friction coefficients (0.69?C0.22) and wear rates (11.90?C0.09?×?10^?5?mm³?N^?1?m^?1) were obtained when rubbing against Inconel 718 alloy from room temperature to 700?°C due to synergetic lubricating action of multiple-lubricants. A smooth lubricating was gradually generated on the worn surface, and the improving of tribological properties was attributed to the formation of lubricious glaze film on the worn surface and their partially transferred to the counterface. The graphite played the main role of lubrication at room temperature, while molybdate phase and graphite were responsible for low friction coefficients and wear rates at mid/high temperatures. The synergetic lubricating effect of molybdate (produced in the rubbing process at high temperatures) iron oxide (transfer from disk material to the pin) and remaining graphite multiple-lubricants play an important lubricating role during friction tests at a wide temperature range.     

Friction and Wear Properties of IF–MoS2 as Additive in Paraffin Oil

Inorganic fullerene-like (IF) MoS₂ nanoparticles with diameters ranging from 70 to 120 nm were synthesized by desulphurizing the MoS₃ precursor and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Tribological properties of the IF–MoS₂, as lubricating oil additive, were evaluated using a MMW-1 four-ball tribotester. The wear scar was examined with an optical microscope and scanning electron microscopy (SEM). The wear resistance of the paraffin oil was improved and the friction coefficient of the oil was decreased by addition of the IF–MoS₂ nanoparticles. The mechanism of friction and wear of the IF–MoS₂ nanoparticles was discussed.     

Further investigation on the tribological behavior of Al2O3–20Ag20CaF2 composite at 650°C

The friction and wear behaviors of the self‐lubricating Al₂O₃–20Ag20CaF₂ disk against an Al₂O₃ pin pair have been investigated over a broad load range from 1 to 30 N and sliding velocities from 0.084 to 1 m/s at 650^°C. Four typical wear modes have been identified and the wear mode map was constructed to illustrate the influence of load and speed on the friction coefficient and wear rate. The results showed the effective self‐lubricating region (II) (continuous lubricating film) is almost independent of sliding speed, and mainly dependent on the load. It is suggested that the plastic deformation and plastic flow during sliding play an important role in the formation of the self‐lubricating film on the sliding surface. Furthermore, the worn surface in the region (II) (continuous lubricating film) was found to be much softer than the original surface and the distribution of Vickers hardness became more uniform due to the presence of the lubricating film on the worn surface. This revised version was published online in July 2006 with corrections to the Cover Date.     

Dry Sliding Friction and Wear Characteristics of Cu-Sn Alloy Containing Molybdenum Disulfide

The wear and sliding friction response of a hybrid copper metal matrix composite reinforced with 10 wt% of tin (Sn) and soft solid lubricant (1, 5, and 7 wt% of MoS₂) fabricated by a powder metallurgy route was investigated. The influence of the percentages of reinforcement, load, sliding speed, and sliding distance on both the wear and friction coefficient were studied. The wear test with an experimental plan of six loads (5–30 N) and five sliding speeds (0.5–2.5 m/s) was conducted on a pin-on-disc machine to record loss in mass due to wear for two total sliding distances of 1,000 and 2,000 m. The results showed that the specific wear rate of the composites increased at room temperature with sliding distance and decreased with load. The wear resistance of the hybrid composite containing 7 wt% MoS₂ was superior to that of the other composites. It was also observed that the specific wear rates of the composites decreased with the addition of MoS₂. The 7 wt% MoS₂ composites exhibited a very low coefficient of friction of 0.35. The hardness of the composite increased as the weight percentage of MoS₂ increased. The wear and friction coefficient were mainly influenced by both the percentage of reinforcement and the load applied. Wear morphology was also studied using scanning electron microscopy and energy-dispersive X-ray analysis.     

Surface Engineering Design of Alumina/Molybdenum Fibrous Monolithic Ceramic to Achieve Excellent Lubrication in a High Vacuum Environment

Al₂O₃/Mo fibrous monolithic ceramics are potential candidates for space applications because of their excellent mechanical properties and low density. This study aims at achieving low friction and long life of this material in a high vacuum environment. Three-dimensional composite-lubricating layers were fabricated by considering texture pattern as storage dimples and MoS₂ synthesized via hydrothermal method as lubricant. The tribological properties were studied sliding against Si₃N₄ ceramic and GCr15 bearing steel balls under high vacuum condition. Results showed that the lubricating properties of the Al₂O₃/Mo fibrous monolithic ceramics were improved greatly by the micro-texture and MoS₂ solid lubricant; the friction coefficients were as low as approximately 0.08 and 0.04, respectively, when Si₃N₄ ceramic and GCr15 bearing steel balls acted as the pairing materials. It was also demonstrated that the low friction coefficient can be realized with various normal loads and sliding speeds, indicating the composite-lubricating layers have good adaptation of working conditions. This excellent performance of the material is mainly because of MoS₂ stored in dimples can be easily dragged onto the friction surface to form lubricating and transferring films during the friction process. This work is an extension of studies that were previously published in Tribology Letters journal.     

Tribological behaviour of a PEEK polymer containing solid MoS2 lubricants

The addition of different concentrations (2–10 wt.%) of molybdenum disulfide (MoS₂) to a poly–ether–ether–ketone matrix has been studied in terms of the thermal, mechanical and tribological properties of the materials. The results of dry‐sliding tribological tests, differential scanning calorimetry and scanning electron microscope–energy‐dispersive X‐ray (EDS) analyses show that the concentration of MoS₂ influences the tribological, mechanical and thermal properties. With the highest concentration of MoS₂ (10 wt.%), the coefficient of friction was reduced by as much as 25%, while the maximum reduction in the wear rate was ~20%, which required 5 wt.% of MoS₂. The most important parameter when it comes to achieving an improved tribological behaviour was found to be the combination of a high hardness and a sufficient quantity of transfer film being formed. Copyright © 2015 John Wiley & Sons, Ltd.     

Effects of ZnO and MoS<Subscript>2</Subscript> Solid Lubricants on Mechanical and Tribological Properties of M50-Steel-Based Composites at High Temperatures: Experimental and Simulation Study

Prospective beneficial effects of mixtures of temperature-adaptive solid lubricants (ZnO–MoS₂) on mechanical and tribological properties of M50 alloy steel were investigated at temperatures from 25 to 800 °C. ZnO and MoS₂ were mixed with M50 (designated as M) to create composites MZ (M50 steel plus ZnO), MM (M50 steel plus MoS₂), and MZM (M50 steel plus both additives). Sliding friction and wear experiments were performed at different temperatures using a pin-on-disk at a sliding speed of 0.2 m s^?1 and a load of 12 N. Silicon nitride and M50 steel were used as the pin materials. In order to understand the friction and wear behavior of composites, analyses of their surfaces were done using XRD, EPMA, FESEM, EDS line/mapping, and XPS tests. A dynamic simulation model based on the finite element method was built to simulate the different stresses on the contact pairs. Results elucidated that MZM attained the least friction (0.17), compared to M (0.40), MZ (0.26), or MM (0.29) at 800 °C. The increase in surface roughness of MZM due to sliding was reduced by 37.3% compared to that of MZ (11.9%) or MM (22.7%). The good lubricating behaviors were referred to the synergetic effects of ZnO, MoS₂, and formed lubricating components on worn surfaces.     

The friction and wear properties of nanometre SiO2 filled polyetheretherketone

Nanometre SiO₂ filled-polyetheretherketone (PEEK) composite blocks with different filler proportions were prepared by compression moulding. Their friction and wear properties were investigated on a block-on-ring machine by running a plain carbon steel (AISI 1045 steel) ring against the composite block. The morphologies of the wear traces and the transfer film were observed by scanning electron microscopy (SEM). It was found that nanometre SiO₂ filled-PEEK exhibited considerably lower friction coefficient and wear rate in comparison with pure PEEK. The lowest wear rate was obtained with the composite containing 7.5 wt.% SiO₂. The SEM pictures of the wear traces indicated that with the frictional couple of carbon steel ring/composite block (fillec with 7.5 wt.% filler), a thin, uniform, and tenacious transfer film was formed on the ring surface. It was inferred that the transfer film contributed largely to the decreased friction coefficient and wear rate of the filled PEEK composites.     

Lubrication of carbon coatings with MoS2 single sheet formed by MoDTC and ZDDP lubricants

The fuel economy and reduction of harmful elements of lubricants are becoming important issues in the automotive industry. One approach to these requirements is the potential use of low‐friction coatings in engine components exposed to boundary lubrication conditions. Diamond‐like carbon (DLC) coatings, extensively studied as ultra‐low friction films to protect ductile metals surfaces for space applications, are expected to fit the bill. The main purpose of this work is to investigate the friction and wear properties of DLC coatings lubricated with molybdenum dithiocarbamate (MoDTC) and zinc dithiophosphate (ZDDP) under boundary lubrication conditions. The mechanisms by which MoDTC reduces the friction in the centirange were studied using ultra‐high vacuum (UHV) analytical tribometer. The UHV friction tests were performed on a tribofilm previously formed on selected DLC material with MoDTC and ZDDP containing oil. Ex‐situ characterizations show that the composition of this tribofilm is similar to that of a tribofilm obtained on steel surfaces in the same lubrication conditions with MoS₂ single sheets dispersed inside zinc phosphate zones. However, analyses by X‐ray photoelectron spectroscopy (XPS) indicate that MoDTC and ZDDP additives seem to be more active on steel surfaces than carbonaceous ones. After UHV friction with the tribofilm formed on selected DLC and steel pin counterpart, the wear scars of both sliding surfaces were characterized by in‐situ analytical tools such as Auger electron spectroscopy, scanning Auger microscopy and micro‐spot XPS. Low friction is associated with the transfer of a thin MoS₂ film to the steel pin counterpart. Copyright © 2006 John Wiley & Sons, Ltd.     

Tribological properties of molybdenum disulphide nanoparticles in soybean oil

Abstract

The tribological properties of soybean oil (SO) with different molybdenum disulfide (MoS₂) additives (hollow nanosphere, nanoplatelet and microplatelet) were investigated. MoS₂ hollow nanospheres remarkably improved the tribological properties of SO. SO with MoS₂ hollow nanospheres decreased abrasive plowing and changed the main wear pattern on the steel friction surfaces into chemical corrosion. The MoS₂ hollow nanospheres easily entered the contact region than the other MoS₂ particles to lubricate the friction pair because of its good dispersibility in SO. The tribochemical reactions among MoS₂ hollow nanospheres, SO and friction material produced a lubricating film composed of MoO₃, Fe₂O₃, carbon containing compounds. Thus, the MoS₂ hollow nanospheres have potential lubricating applications with SO. By contrast, MoS₂ nanoplatelet and microplatelets had lesser effects on the lubricating effect of SO. The MoS₂ nanoplatelets, even with its smaller size and more active chemical properties, had more difficulty in entering into the contact region because of its low dispersibility in the base oil.     

Influence of Sliding Speed on the Tribological Characteristics of Si3N4-hBN Ceramic Materials

The influence of sliding speed on the unlubricated tribological behaviors of silicon nitride–boron nitride (Si₃N₄-hBN) composites was investigated with two modes in air by a pin-on-disc tribometer. Using the upper disc–on–bottom pin test mode, as the sliding speed increased, the friction coefficient of the sliding pairs showed an upward trend; for example, from 0.18 at the sliding speed of 0.40 m/s to 0.54 at the sliding speed of 1.31 m/s for the Si₃N₄/Si₃N₄–20% hBN pair. The surface analysis indicated that a tribochemical film consisting of SiO₂ and H₃BO₃ formed on the wear surfaces of the Si3N4/Si3N4–20% hBN sliding pair at sliding speeds of 0.40 and 0.66 m/s. Moreover, the formation of this film lubricated the wear surfaces. At the sliding speed of 1.31 m/s, no tribochemical film formed on the wear surfaces, most likely due to the increase in surface temperature. In the upper pin–on–bottom disc test mode, the wear mechanism was dominated by abrasive wear, and no tribochemical products could be detected on the wear surfaces. The increase in sliding speed weakened the degree of abrasive wear, leading to a decrease in the friction coefficients.     

Effects of sintering aids and solid lubricants on tribological behaviours of CMC/Al2O3 pair at 650°C

Ten kinds of self-lubricating composites with different amounts of sintering aids and solid lubricants in Al₂O₃ matrix were fabricated by hot-pressed sintering. Their friction and wear behaviours in unlubricated sliding against Al₂O₃ were tested by using a pin-on-disk wear tester at 650°C. It was shown that the amount of sintering aids strongly affected friction coefficient and wear rate of the Al₂O₃–20Ag20CaF₂ composite, the appropriate amount of sintering aids was 10 wt% for beneficial effect on the reduction of wear at 650°C. Also it was shown that the addition of equal quantities of Ag and CaF₂ in Al₂O₃ matrix can promote the formation of the well-covered lubricating film, and effectively reduce the friction and wear. The composite with 40 wt% of lubricants (20 wt% Ag, 20 wt% CaF₂) presented an optimum tribological behavior at 650°C (friction coefficient μ is about 0.3, wear rates are about 4 x 10^-6 mm³/N,m and 5 x 10^-7 mm³/N,m for the disk and pin, respectively). This revised version was published online in August 2006 with corrections to the Cover Date.     

An investigation of friction and wear performances of bonded molybdenum disulfide solid film lubricants in fretting conditions

The friction and wear performances of bonded MoS₂ solid film lubricants with the counterpart steel ball rubbing were investigated in fretting wear conditions in order to inquire into the load-carrying capacity and wear mechanisms of bonded MoS₂ solid film lubricants under dry friction conditions. Experimental results show that the bonded MoS₂ solid film lubricants have excellent anti-friction and wear-resistance performances within a wide load range between 20 N and 800 N and within a wide oscillatory frequency range between 5 Hz and 30 Hz. It is found through analyses of the transfer films formed in the surface of the counterpart steel ball investigated by SEM, XPS and AES, that the thickness of the transfer film formed is about 38 nm and the oxidation of MoS₂ in the transfer films does not occur during dry friction process. The high load and frequency promote the formation of a compact transfer films. The compact transfer films are believed to be the predominant mechanism giving rise to high load-carrying capacity, and excellent wear-resistance performances of the bonded MoS₂ solid film lubricants.     

Nano Si3N4 composites with improved tribological properties

Nano Si₃N₄ composites with tailored microstructure were developed using fine ß‐Si₃N₄ powders. Their wear behaviour was investigated. Whereas pure Si₃N₄ composites showed improved wear behaviour under dry rolling conditions with slip, TiN‐reinforced nano Si₃N₄ composites generate a self‐lubricating behaviour under dry sliding conditions. After chemical treatment with hydrogen sulphide, the friction coefficient and wear rate was found to be significantly decreased under dry sliding conditions. Additionally, the new composites possess higher fracture toughness than the pure nano Si₃N₄ materials. Copyright © 2009 John Wiley & Sons, Ltd.     

In Situ Analysis of Third Body Contributions to Sliding Friction of a Pb–Mo–S Coating in Dry and Humid Air

Reciprocating sliding tests of ion-beam deposited (IBD) Pb–Mo–S coatings were performed with an in situ tribometer that allows real-time visualization and Raman analysis of the sliding contact through a transparent hemisphere. Experiments were performed in dry air, ambient air (∼50% RH) and mixtures of dry and humid air cycled between low and high humidity. Third bodies formed in the sliding contact were monitored through an optical microscope and analyzed by Raman Spectroscopy. Third body velocity accommodation modes were identified and correlated with friction behavior in dry and ambient air. The dominant velocity accommodation mode in both dry and humid air was interfacial sliding between the outer surface of the transfer film and the wear track; this interface, based on present and earlier studies, is crystalline MoS₂. Therefore, the friction coefficient was controlled by the interfacial shear strength of MoS₂ sliding against MoS₂. Humid air sliding was accompanied by a rise in the friction coefficient and a small but observable second velocity accommodation mode: shear/extrusion of the transfer film. It is concluded that the friction rise in humid air was due to an increase in the interfacial shear strength, and that the rise in friction caused the third body to deform rather than the deformation causing the friction to rise.     

Effect of electrical current on the tribological behavior of the Cu-WS2-G composites in air and vacuum

As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.