用磁控溅射和退火方法制备AlSb多晶薄膜

采用磁控溅射法在玻璃衬底上制备Al/Sb预制多层薄膜,然后将Al/Sb预制多层薄膜在退火炉中退火得到AlSb多晶薄膜.用X射线衍射(XRD)法测薄膜结构;用扫描电镜(SEM)测薄膜Al/Sb成分比,结果表明AlSb多晶薄膜具有单一的晶相、均匀的结构,以及粒径大约20nm的晶粒.根据电导率(lnσ)与温度(T)的关系得到电导激活能为0.21和0.321eV,为制备出适用于太阳电池的AlSb多晶薄膜奠定了一定的技术基础.     

用共蒸发法制备AlSb多晶薄膜

采用元素共蒸发法结合退火处理制成了AlSb多晶薄膜.利用x射线衍射、透射光谱、暗电导温度关系等方法研究了薄膜的结构、光学和电学性质.发现540℃退火后得到的AlSb多晶薄膜呈立方相结构,间接跃迁光能隙为1.62eV,电导激活能约为0.33eV.研究结果表明,AlSb薄膜有可能成为新型太阳电池的重要材料.     

用共蒸发法制备AlSb多晶薄膜

采用元素共蒸发法结合退火处理制成了AlSb多晶薄膜.利用x射线衍射、透射光谱、暗电导温度关系等方法研究了薄膜的结构、光学和电学性质.发现540℃退火后得到的AlSb多晶薄膜呈立方相结构,间接跃迁光能隙为1.62eV,电导激活能约为0.33eV.研究结果表明,AlSb薄膜有可能成为新型太阳电池的重要材料.     

太阳电池中CdS多晶薄膜的微结构及性能

采用化学水浴法制备了CdS多晶薄膜，通过XRD，AFM，XPS和光学透过率谱等测试手段研究了CdS多晶薄膜生长过程中的结构和性能.结果表明，随着沉积的进行，薄膜更加均匀、致密，与衬底粘附力增强，其光学能隙逐渐增大，薄膜由无定形结构向六方(002)方向优化生长，同时出现了Cd(OH)2相.在此基础上，通过建立薄膜的生长机制与性能的联系，沉积出优质CdS多晶薄膜，获得了转化效率为13.38%的CdS/CdTe小面积电池.     

太阳电池中CdS多晶薄膜的微结构及性能

采用化学水浴法制备了CdS多晶薄膜,通过XRD,AFM,XPS和光学透过率谱等测试手段研究了CdS多晶薄膜生长过程中的结构和性能.结果表明,随着沉积的进行,薄膜更加均匀、致密,与衬底粘附力增强,其光学能隙逐渐增大,薄膜由无定形结构向六方(002)方向优化生长,同时出现了Cd(OH)2相.在此基础上,通过建立薄膜的生长机制与性能的联系,沉积出优质CdS多晶薄膜,获得了转化效率为13.38%的CdS/CdTe小面积电池.     

CdS薄膜的真空热蒸发制备及在CIGS薄膜太阳电池中的应用

采用真空热蒸发(VTE)的方法制备了CdS多晶薄膜,研究了不同衬底温度对其微观结构与光电性能的影响。结果显示,不同衬底温度下制备的CdS薄膜均属于六方相多晶结构且具有(002)择优取向;随着衬底温度的升高,(002)特征衍射峰强度增加,半高宽变小,相应薄膜结晶度增大;由CdS薄膜的透射光谱可知,在500~1 000nm波段平均透过率均超过80%,光学带隙随着衬底温度的升高而增大(2.44~2.56eV),表明真空热蒸发方法制备的CdS薄膜可以作为CIGS薄膜太阳电池的缓冲层。将真空热蒸发法制备CdS薄膜与磁控溅射法制备CIGS薄膜太阳电池相结合,在同一真空室内得到了CIGS薄膜太阳电池器件,为CIGS薄膜太阳电池的工业化推广提供了新途径。     

SnO2:Sb薄膜的制备和光致发光性质

用射频磁控溅射法在玻璃衬底上制备出SnO2:Sb薄膜.制备样品为多晶薄膜,具有纯氧化锡的四方金红石结构和(110)择优取向,Sb离子以替位式掺杂的形式存在于SnO2晶格中.室温条件下对样品进行光致发光测量,在392nm附近观测到强的紫外-紫光发射,发射强度随制备功率的增加而增强,且样品退火后发射强度也明显增强.紫外-紫光发射的起源被归于由Sb形成的施主能级和受主能级之间的电子跃迁.     

SnO2∶Sb薄膜的制备和光致发光性质

用射频磁控溅射法在玻璃衬底上制备出SnO2∶Sb薄膜．制备样品为多晶薄膜，具有纯氧化锡的四方金红石结构和(110)择优取向，Sb离子以替位式掺杂的形式存在于SnO2晶格中．室温条件下对样品进行光致发光测量，在392nm附近观测到强的紫外-紫光发射，发射强度随制备功率的增加而增强，且样品退火后发射强度也明显增强．紫外-紫光发射的起源被归于由Sb形成的施主能级和受主能级之间的电子跃迁．     

(Al,Zr)共掺杂ZnO透明导电薄膜的结构以及光电性能研究

用射频磁控溅射法在玻璃衬底上氩气气氛中制备出(Al,Zr)共掺杂的ZnO透明导电薄膜,研究了不同Zr掺杂浓度和薄膜厚度ZnO薄膜的结构、电学和光学特性。结果表明,在最佳沉积条件下我们制备出了具有(002)单一择优取向的多晶六角纤锌矿结构,电阻率为2.2×10-2Ω.cm,且可见光段(320～800nm)平均透过率达到85%的ZnO透明导电薄膜。在150℃的条件下对(Al,Zr)共掺杂的ZnO薄膜进行1h的退火处理,薄膜电阻率降低至8.4×10-3Ω.cm。Zr杂质的掺入改善了薄膜的可见光透光性。     

TiO_2的制备及其在钙钛矿太阳电池中的应用

分别采用溶液法和磁控溅射法制备了TiO_2薄膜。其中对采用磁控溅射法制备的样品进行了退火。用扫描电子显微镜(SEM)观察了薄膜的表面形貌,表征结果发现,与溶液法制备的TiO_2薄膜相比,采用磁控溅射法制备的薄膜更加致密,表面粗糙度更低。X射线衍射(XRD)测试结果说明,溶液法制备的薄膜是多晶结构,而磁控溅射制备的薄膜是非晶结构,经过500℃退火后溅射的样品也只有一个(101)峰。在制备好的TiO_2薄膜上旋涂钙钛矿层,将其制备成太阳电池,并测试其光电性能。I-V曲线表明,采用磁控溅射法制备的TiO_2薄膜制备的电池具有更高的开路电压。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.