Development of cellulose-based bactericidal nanocomposites containing silver nanoparticles and their use as active food packaging

The use of nanomaterials, including metallic as active fillers in polymeric nanocomposites for food packaging has been extensively investigated. Silver nanoparticles (AgNPs), in particular, have been exploited for technological applications as bactericidal agents. In this paper, AgNPs were incorporated into a hydroxypropyl methylcellulose (HPMC) matrix for applications as food packaging materials. The average sizes of the silver nanoparticles were 41 nm and 100 nm, respectively. Mechanical analyses and water vapor barrier properties of the HPMC/AgNPs nanocomposites were analysed. The best results were observed for films containing smaller (41 nm) AgNPs. The antibacterial properties of HPMC/AgNPs thin films were evaluated based on the diameter of inhibition zone in a disk diffusion test against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). The disk diffusion studies revealed a greater bactericidal effectiveness for nanocomposites films containing 41 nm Ag nanoparticles.     

Antimicrobial and physicomechanical natures of silver nanoparticles incorporated into silicone-hydrogel films

PurposeThe effects of silver nanoparticles (AgNPs) incorporated in silicone-hydrogel films on their physicochemical properties and microbial activity were investigated.MethodsSilicone-hydrogel composite films (SiHCFs) were prepared by in-situ chemical reduction of silver ions added in different concentrations (0, 10, 20, 30, 40, 60, and 80 ppm) followed by ultraviolet (UV) casting. The reduction of silver ions into AgNPs was confirmed by transmission electron microscopy (TEM) and absorption spectroscopy over ultraviolet and visible (UV–vis) wavelengths. Incorporation of AgNPs into SiHCFs was confirmed by UV–vis absorption spectroscopy, scanning electron microscopy (SEM), and energy-dispersive X-ray (EDX) spectroscopic mapping. The physico- mechanical properties of the SiHCFs were evaluated. Antimicrobial activity and biofilm formation of Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus were assessed.ResultsTEM, UV–vis absorption, SEM, and EDX mapping showed that silver ions were reduced in the mixture of co-polymerizing monomers and incorporation of AgNPs into SiHCFs was achieved. Mechanical properties of the SiHCFs were enhanced with increasing AgNPs concentration without affecting their chemical and thermal properties. SiHCFs exhibited transmittance greater than 90% at a wavelength 600 nm. Bacterial growths in the solutions bathing the SiHCFs with increasing silver concentration were 95, 78, 4, 2, 0, 0, 0% respectively, for Escherichia coli; 95, 82, 4, 0.6, 0, 0, 0% for Pseudomonas aeruginosa; and 93, 79, 4, 0.5, 0, 0, 0% for Staphylococcus aureus.ConclusionsIncorporation of AgNPs into SiHCFs demonstrated sufficient release of AgNPs to inhibit bacterial growth and reduce biofilm formation, with collateral enhancement of some mechanical properties of SiHCFs.     

In vitro assessment of antibacterial potential and mechanical properties of Ag-TiO2/WPU on medical cotton optimized with response surface methodology

The environmental-friendly, economical, and simple one pot formulation for enhanced antibacterial and mechanical property finishing on medical cotton fabrics was successfully developed and optimized using a central composite design in conjunction with response surface methodology. It combines the concepts of in situ synthesis of AgNPs and photocatalytic property of TiO₂ in waterborne polyurethane as the finishing emulsion without additional organic reducing or stabilizing agent. The optimal formulation with contents of AgNO₃ (240 ppm) and TiO₂ NPs (980 ppm) exhibited excellent antibacterial activities against Klebsiella pneumoniae and Staphylococcus aureus with over 99% reduction and improved mechanical properties as well as non-toxicity to mammalian cells.     

Antimicrobial Effects of Silver Nanoparticles Synthesized by Fatsia japonica Leaf Extracts for Preservation of Citrus Fruits

Due to their potent antimicrobial activity, silver nanoparticles (AgNPs) synthesized by biomass might be promising in food preservation, whereas effects of AgNPs on Penicillium italicum‐induced rot of Citrus fruits have not been investigated. In this study, a novel AgNPs biosynthesis method was developed based on Fatsia japonica leaf extracts. It was revealed that concentrations of leaf extracts, AgNO₃ and NaCl affected AgNPs yields and particle sizes obviously. Under the optimized conditions (8 mg/mL extracts, 2 mM AgNO₃ and 1 mM NaCl), AgNPs, synthesized within 80 min, showed potent preservative effect against P. italicum‐induced rot of Citrus fruits. Furthermore, inhibition test and TEM analysis indicated that as‐synthesized AgNPs caused cell deformation, cytoplasmic leakage, and thereupon cell death of P. italicum. Moreover, AgNPs had significant antibacterial activities against Escherichia coli and Staphylococcus aureus, which might be beneficial for Citrus fruits preservation. Altogether this study develops an efficient AgNPs synthesis method and a novel preservation method for Citrus fruits.     

Measurement of engineered nanoparticles in consumer products by surface-enhanced Raman spectroscopy and neutron activation analysis

There has been an increasing number of consumer and food products sold on the market that contain various engineered nanomaterials (ENMs) such as silver nanoparticles (AgNPs) and gold nanoparticles (AuNPs). These nanomaterials possess novel physical and chemical properties that can be used for wide applications in agriculture and food safety. However, current analytical methods to detect and measure ENMs are time-consuming, labor-intensive, and expensive. The objective of this study was to develop a novel, simple, rapid, and accurate method to detect AgNPs and AuNPs in consumer products using surface-enhanced Raman spectroscopy (SERS). SERS measurement was conducted to detect AgNPs and AuNPs using an effective Raman indicator, 4-aminothiophenol (pATP). The pATP can strongly bind onto nanoparticles, generating greatly enhanced Raman signals that can be used for measurement. The pATP was combined with Ag or Au stock solution, AgNO₃, citrate-coated AgNPs, citrate-coated AuNPs, AuCl, AgNPs, AuNPs, and five commercial products to study the differences in their SERS spectral data. The observed spectra of AgNPs and AuNPs have similar peaks at ~?390, ~?1087, and ~?1590 cm^?1 that can be attributed to the C–S stretching vibration, C–C stretching vibration, and C–H stretching vibration, respectively. Neutron activation analysis (NAA) and electron microscopy was used to characterize and quantify AgNPs and AuNPs in the consumer products. The results demonstrate that SERS method in combination with NAA can be an effective method for detection of ENMs, and it can easily distinguish AgNPs and AuNPs from other non-nanoparticle species in the complex matrices.     

Preparation and characterization of a temperature-sensitive nonwoven poly (propylene) with antibacterial properties

In this study, a temperature-sensitive fabric with antibacterial properties was prepared by the formation of silver nanoparticles (AgNPs) on nonwoven poly (propylene) (PP) grafted with poly (N-iso-propylacrylamide) (PNIPAAm-PP). First, PNIPAAm was grafted onto corona-treated nonwoven PP. Afterwards, silver nanoparticles were synthesized on the temperature-sensitive hydrogel layer grafted to the surface of nonwoven PP by the reduction of silver ions (Ag⁺). Fourier transform infra-red spectroscopy confirmed the presence of PNIPAAm on the nonwoven PP. scanning electron microscopy-energy dispersive X-ray spectroscopy was used to investigate surface morphology and the presence of silver particles in the samples. Inductively coupled-plasma atomic emission spectroscopy revealed that the Ag content in Ag-functionalized PNIPAAm-PP was significantly higher than Ag-functionalized corona-treated PP with the same concentration of silver solution. Moreover, the results of the swelling rate experiment confirmed that PNIPAAm-PP maintained temperature-sensitive properties after functionalizing with Ag. The results showed that the formation of AgNPs with enhancement in antibacterial property was possible onto PNIPAAm-PP.     

Development of antimicrobial whey protein-based film containing silver nanoparticles biosynthesised by Aspergillus Niger

Applications of whey protein concentrate (WPC)-based films have been limited in the food industry due to their poor mechanical properties. This research aims to evaluate the effect of silver nanoparticles (AgNPs) synthesised by Aspergillus niger on the mechanical and antimicrobial properties of WPC-based films. The biosynthesised AgNPs solution was added into the WPC film formula at the concentration of 0, 0.25 and 1.25 mm . The film samples containing AgNPs inhibited the growth of Staphylococcus aureus, Escherichia coli O157:H7, Salmonella Enteritidis, Listeria monocytogenes, Williopsis saturnus or Aspergillus sydowii with zones of inhibition ranging from 13 to 19.7 mm. Incorporation of AgNPs improved tensile strength and water barrier properties of the films by 84% and 67%, respectively. However, per cent elongation at the break of the film decreased from 37% to 11% by the addition of 1.25 mm AgNPs. This work provides a protocol for preparing improved antimicrobial WPC films with AgNPs.     

蛋壳粉纳米银抗菌材料的制备及抑菌性研究

以蛋壳粉为原料通过超声波还原法与AgNO_3、NaBH_4作用,制备蛋壳粉纳米银。通过扫描电镜观察蛋壳粉纳米银的形貌及被其处理过的菌的形貌变化,并通过微生物方法对其抑菌性进行研究。结果表明,蛋壳粉纳米银对大肠杆菌、金黄色葡萄球菌、枯草芽孢杆菌、白色念珠菌4种菌均有较好的抑菌效果,最低抑菌浓度(MIC)分别为1. 5,3. 0,3. 0,6. 0 mg/L,最低杀菌浓度(MBC)值分别为6,12,12,24 mg/L。     

Physical,mechanical, and antibacterial characteristics of bio-nanocomposite films loaded with Ag-modified SiO2 and TiO2 nanoparticles

In this study, starch-based films incorporating metal oxide (MO₂) nanoparticles (NPs) of TiO₂ and SiO₂ (at a concentration of 1 to 4 wt. %) were produced by solution casting method. In order to exhibit antimicrobial properties, MO₂ NPs were modified by synthesizing silver (Ag) ions over the NPs using cationic adsorption method. Ag ions were then reduced to metallic Ag by sodium borohydride solution. Scanning electron microscopy showed a smooth surface for the pure starch film. Incorporating MO₂@Ag NPs in the films increased surface roughness with agglomerated NPs within starch matrix. Energy dispersive X-ray analysis exhibited a uniform dispersion of Ag-loaded MO₂ NPs, which increases surface contact between these NPs and the biopolymer matrix leading to improved physical and mechanical properties of the resulting films. With increasing in the NPs concentrations, the tensile strength and elongation at break % of the films increased and decreased, respectively. Incorporating MO₂@Ag NPs into starch matrix decreased solubility in water and water vapor permeability of the obtained films, and significantly inhibited the growth of Escherichia coli and Staphylococcus aureus. The most antibacterial effect was obtained for the films containing higher weight concentrations of Ag-loaded SiO₂-NPs.     

Synthesis and characterization of nanosilver-silicone hydrogel composites for inhibition of bacteria growth

Purpose

Nanosilver-silicone hydrogel (NAgSiH) composites for contact lenses were synthesized to asses the antimicrobial effects.

Fabrication of superhydrophobic,antibacterial, and ultraviolet-blocking cotton fabric

Inspired by the superhydrophobic behavior of lotus leaf, a simple coating method was developed which could facilitate bionic creation of superhydrophobic surfaces on cotton textiles with a new functional properties. Silver nanoparticles (AgNPs) with a high deposition density were formed on the surface of cotton fabric through an alkali pre-activation followed by in situ reduction of silver nitrate. The Ag-coated fabric was then reacted with octyltriethoxysilane (OTES) to form a low surface energy layer on the fiber surface. The fabrics were characterized by ultraviolet-visible reflectance spectrophotometry, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy, and X-ray diffractometry. Hydrophobicity properties were assessed by contact angle (CA) goniometry and shedding angle (SHA) technique. Antibacterial activity was measured against Staphylococcus aureus and Escherichia coli bacteria, and UV-blocking ability was measured using the AATCC method. SEM images showed the formation of AgNPs which were distributed uniformly on the fibers’ surface with a high coating density. Superhydrophobicity property of the treated fabric was confirmed with the CA of 156° and SHA of 8°. High antibacterial activity was observed without the reduction of inhibition size after coating with the OTES. The fabric also showed excellent UV-blocking with the ultraviolet protection factor of 266.01.     

Melt Production and Antimicrobial Efficiency of Low-Density Polyethylene (LDPE)-Silver Nanocomposite Film

Colloidal silver nanoparticles with a size of 5.5 ± 1.1 nm were prepared by chemical reduction using polyethylene glycol (PEG). Silver nanoparticles were incorporated into low-density polyethylene (LDPE) by melt blending and subsequent hot pressing at 140 °C to produce nanocomposite film with an average thickness of 0.7 mm. PEG was added at 5% weight of polymer as a compatibilizer agent in order to prevent agglomeration and provide uniform distribution of nanoparticles in polymer matrix. Antimicrobial activity of silver nanocomposites against Escherichia coli ATCC 13706, Staphylococcus aureus ATCC12600, and Candida albicans ATCC10231 was evaluated by semi-qualitative agar diffusion test and quantitative dynamic shake flask test. Mechanical properties of nanocomposites were not significantly different from silver-free LDPE-containing PEG films (p > 0.05), and silver nanoparticles did not form chemical bonding with the polymer. LDPE-silver nanocomposite samples by more than 6.69 ppm silver nanoparticles showed considerable antimicrobial clear zone. LDPE-silver nanocomposite affected growth kinetic parameters of the examined bacteria and is more efficient on S. aureus than E. coli. Polyethylene-silver nanocomposites containing 22.64 ppm silver nanoparticles could reduce 57.8% growth rate and 23.3% maximum bacterial concentration and increase 35.8% lag time of S. aureus. This study shows the potential use of LDPE-silver nanocomposite as antimicrobial active film. Antimicrobial efficiency of silver nanocomposite depends on silver nanoparticles concentration; however, high level of silver nanoparticles may lead to weakening of mechanical properties.     

Postharvest Quality of Fresh-Cut Carrots Packaged in Plastic Films Containing Silver Nanoparticles

Active food packaging containing antimicrobial additive goes beyond traditional functions of packaging, once it can extend food shelf life maintaining its quality, safety and reducing postharvest losses by controlling food spoilage. Among several antimicrobial additives employed in polymeric films for packaging, metallic nanoparticles outstand due to its facility for synthesis, low-cost of production, and intense antimicrobial properties. In this work, extruded plain films of low-density polyethylene (LDPE) containing silver nanoparticles (AgNPs) embedded in SiO₂ and TiO₂ carriers (namely MS and MT, respectively) were produced and used as active packaging for maintaining the physicochemical and microbiological quality of carrots (Daucus Carota L. cv. Brasília). The neat (LDPE) and composite films containing MS and MT were characterized by scanning electron microscopy and permeability to oxygen and used for packaging fresh-cut sliced carrots stored at 10 °C for 10 days. After the storage time, the physicochemical properties of carrots were characterized, while the antimicrobial properties of films and AgNP migration were investigated. Our results revealed that both MT and MS packages showed antimicrobial activity even for films containing low concentration of AgNP. In addition, AgNP antimicrobial activity demonstrated to be carrier-dependent, once MT-LDPE showed improved performance compared to MS-LDPE. Regarding the physicochemical properties of packaged carrot, lower soluble solids and weight loss and higher levels of ascorbic acid were observed for carrots packaged with MT-LDPE films (compared to MS-LDPE), leading to a better postharvest quality conservation. Such differences observed in physicochemical properties of carrots are related to the distinct antimicrobial and film permeability properties for each composite film. In addition, under the conditions employed in this study, AgNP migration from the packages to fresh-cut carrot was not observed, which is highly desirable for food packaging safety, indicating the potential of such active packages for food preservation application.     

Colorimetric detection of the β-agonist ractopamine in animal feed,tissue and urine samples using gold–silver alloy nanoparticles modified with sulfanilic acid

A highly sensitive, selective and simple method was proposed for colorimetric detection of ractopamine on the basis of the interaction between ractopamine and sulfanilic acid-modified gold–silver alloy nanoparticles (AuAgNPs). The AuAgNPs were prepared by the reduction of HAuCl₄ and AgNO₃ with sodium citrate in aqueous medium and further modified by sulfanilic acid. The interaction of ractopamine with sulfanilic acid induced rapid aggregation of sulfanilic acid-modified AuAgNPs along with an optical colour change, leading to precise quantification which could be detected by absorptiometry. Under the optimum conditions, the absorbance ratio (A₆₀₀/A₄₃₅) of sulfanilic acid-modified AuAgNPs exhibited a linear relationship with the concentration of ractopamine in the range of 4.5–31.6 ng/mL. The detection limit of ractopamine was 1.5 ng/mL. The established novel colorimetric detection method showed high selectivity towards ractopamine. The method was successfully applied to detect ractopamine in spiked pork, swine feed and swine urine samples with excellent recoveries from 94.4% to 112.5%. These results demonstrated that the proposed new method has a good potential for practical applications.     

Characterization and evaluation of the Ag+-loaded soy protein isolate-based bactericidal film-forming dispersion and films

Abstract: This study aims to prepare bactericidal films developed from soy protein isolate (SPI) based film‐forming dispersions (FFDs) for use in the food and medical fields. The FFD and films were prepared after the incorporation of different concentrations of AgNO₃ as a bactericidal agent. The transparency, tensile strength, and antimicrobial features were evaluated. Structural characterizations were also performed by Fourier transform infrared spectroscopy, scanning electron microscope, and atomic force microscopy analysis. Results showed that the opacity of these FFD was greatly decreased after the incorporation of AgNO₃. The SPI‐5 film has the largest tensile strength (P < 0.05) compared with that of the other ones. Micro structural imaging analysis showed an increase in the surface irregularities with the addition of AgNO₃. The minimum inhibitory concentration of AgNO₃ was 336 μg/mL FFD for both Escherichia coli ATCC 25923 and Staphylococcus aureus ATCC 25922. The SPI‐AgNO₃ films developed from the FFD with the minimal AgNO₃ concentration at 336 μg/mL FFD also showed bactericidal effects for both the strains. These results may prove promising for the use of SPI‐AgNO₃ films in the food or medical industries. Practical Application: The films prepared in this study are biodegradable and will be used in medical and food fields.     

Single step green process for the preparation of antimicrobial nanotextiles by wet chemical and sonochemical methods

Abstract

In this work, the green synthesis of silver nanoparticles (AgNPs) was carried out by using Zanthoxylum rhesta plant’s fruit extract for the first time. The green synthesis and in situ deposition of AgNPs on cellulose fibers in cotton was carried out by wet and sonochemical methods. The AgNPs and AgNPs-deposited cotton fabrics were fully characterized. The crystallite size of particles obtained by both methods was around 37?nm and the hydrodynamic diameters were in the range of 69 to 184?nm and 75 to 111?nm. The scanning electron microscopy (SEM) images showed uniform deposition of the nanoparticles on cotton fabrics. The AgNPs-deposited cotton fabrics showed excellent antibacterial activities against gram positive and gram negative bacteria namely, Escherichia coli (E-coli), Staphylococcus aureus, Pseudomonas aeruginosa, and Bacillus subtilis. This work presents a significant advancement in the preparation of antimicrobial nanotextiles by a smart combination of green synthesis and in situ deposition approach.     

Stabilized nanosilver based antimicrobial poly(3-hydroxybutyrate-co-3-hydroxyvalerate) nanocomposites of interest in active food packaging

Antimicrobial silver based nanocomposites of poly(3-hydroxybutyrate-co-3-hydroxyvalerate) were successfully synthesized and characterized. For the synthesis, a masterbatch of in situ stabilized silver nanoparticles (AgNPs) produced into a mixed microbial cultures based poly(3-hydroxybutyrate-co-18 mol%-3-hydroxyvalerate) (PHBV18) was used, which was diluted by melt compounding with a commercial poly(3-hydroxybutyrate-co-3 mol%-3-hydroxyvalerate) (PHBV3) material. The incorporated AgNPs (0.04 wt.%) led to a surprising oxygen permeability drop of ca. 56% compared to the neat polymer. The thermal stability and optical properties of the nanocomposites were not significantly modified as compared to the neat PHBV3. Moreover, the antimicrobial performance of the PHBVs-AgNPs films against two of the most common food borne pathogens, Salmonella enterica and Listeria monocytogenes, showed a strong and sustained (even after seven-months) antibacterial activity. This study provides an innovative route to generate fully renewable and biodegradable antimicrobial nanocomposites that could potentially be of interest in film and coating applications such as active food packaging.Industrial relevanceAs a response to the consumers for more safety foodstuffs and ecofriendly packaging materials, this work presents a novel methodology to develop antimicrobial packaging by using biodegradable materials obtained from industrial food by-products in combination of an industrially meaningful melt blending process. The methodology here applied allows the use of low doses of stabilized silver nanoparticles in the polymer matrix, without additives, which exhibits prolonged antimicrobial activity against food borne pathogens and enhanced oxygen barrier properties. These materials are of great interest in the development and design of biodegradable active food packaging materials and antibacterial food contact surfaces with the additional advantage that they can be easily scale-up.     

Anatase titanium dioxide loaded polylactide membranous films: preparation,characterization, and antibacterial activity assessment

In this study, the preparation method and characteristics of anatase titanium dioxide (TiO₂) nanoparticle-loaded polylactide (PLA) films and their antibacterial efficacy against Klebsiella pneumoniae (ATCC 4352) and Staphylococcus aureus (ATCC 6538) bacterium were studied. A series of PLA nanocomposites containing, respectively, 0, 1, and 5% (wt.) titanium dioxide (TiO₂) nanoparticles were prepared by melt intercalation method. The effect of TiO₂ nanoparticles on the thermal and mechanical characteristics of the films was determined. Thermal analysis showed that the glass transition temperature, crystallization temperature, melting temperature, and decomposition temperatures (Td_0.5 and Td_0.05) decreased with the filler content. The results obtained from tensile tests showed that TiO₂ nanoparticles reduced the mechanical properties and moduli of the PLA films. On the other hand, the water absorption properties of the nanocomposite films increased with the addition of nanoparticles and nanocomposite films exhibited bacteriostatic and limited bactericidal efficacy according to AATCC 147. Consequently, nanocomposite films may be good materials for medical applications due to their membranous properties.     

Characterisation of acid-soluble collagen from skin of silver carp (Hypophthalmichthys molitrix)

Acid-soluble collagen (ASC) from the skin of silver carp (Hypophthalmichthys molitrix) was isolated and some properties of ASC were investigated. SDS–PAGE patterns showed ASC from silver carp skin was type ? collagen. Sulfopropyl-Toyopearl 650(M) column chromatography indicated that ASC from silver carp skin was composed of three kinds of α chains, α₁, α₂ and α₃. Hydroxyproline and proline content of ASC from silver carp skin was 192 residues/1000 residues, which was similar to that of ASC from carp skin. Denaturation temperature (T_d) of ASC from silver carp skin was around 29 °C. The results showed that some properties of ASC from silver carp skin were similar to those of ASC from carp skin. However, the peptide map of ASC from silver carp skin digested by pepsin was distinguished with that of ASC from carp skin.     

Modification of the microstructural and physical properties of konjac glucomannan-based films by alkali and sodium carboxymethylcellulose

Edible films were cast from konjac glucomannan (KGM) solutions, with or without added alkali (KOH) and/or sodium carboxymethylcellulose (CMC). Four types of KGM-based films (KGM, KGM–KOH, KGM–CMC and KGM–CMC–KOH) were produced and characterized by scanning electron microscopy (SEM), wide-angle X-ray diffraction (WAXD), moisture sorption, water vapour permeability (WVP), and tensile tests. Tensile properties were studied as a function of water activity (a_w) over the range from 0.22 to 0.84. SEM revealed that films, with and without KOH, exhibited cross-sectional lamellar structures running perpendicular and parallel, respectively, to the film surface. Alkali treatment produced films with enhanced crystallinity, lower water-sorptive capacity (WSC) and WVP, and higher tensile properties. These effects were attributed to alkaline deacetylation of KGM molecules which permitted greater intermolecular interactions. The presence of CMC appeared to suppress crystallinity of native KGM films, but enhanced that of deacetylated KGM films. Films incorporating CMC exhibited higher WSC and WVP, but variable tensile properties depending on alkali treatment and a_w. The tensile properties of all KGM-based films were profoundly affected by a_w. Tensile modulus (TM) of all films were antiplasticized as a_w was increased from 0.22 to 0.43, but tensile strength (TS) was generally plasticized by water. Tensile elongation of KGM, KGM–KOH, and KGM–CMC–KOH films was generally much less sensitive to water. However, KGM–CMC films exhibited minimum elongation, attributed to antiplasticization by water, over the intermediate a_w range from 0.43 to 0.69. KGM–CMC–KOH films exhibited the highest TM and TS at any particular a_w.