A 2.5 mW 80 dB DR 36 dB SNDR 22 MS/s Logarithmic Pipeline ADC

A switched-capacitor logarithmic pipeline analog-to-digital converter (ADC) that does not require squaring or any other complex analog function is presented. This approach is attractive where a high dynamic range (DR), but not a high peak SNDR, is required. A prototype signed, 8-bit 1.5 bit-per-stage logarithmic pipeline ADC is designed and fabricated in 0.18 mum CMOS. The 22 MS/s ADC achieves a measured DR of 80 dB and a measured SNDR of 36 dB, occupies 0.56 mm², and consumes 2.54 mW from a 1.62 V supply. The measured dynamic range figure of merit is 174 dB.     

A 100 MS/s 4 MHz Bandwidth 70 dB SNR $Delta Sigma$ ADC in 90 nm CMOS

This paper describes the results of an implementation of a high speed $Delta Sigma$ ADC in 90 nm CMOS process, which is developed for a direct-conversion digital TV receiver. The $Delta Sigma$ ADC is based on a switched-capacitor fourth-order single-loop $Delta Sigma$ modulator with a 4-bit quantizer. The ADC uses a triple sampling technique and a two-step summation scheme for low power and high speed operation. Also, a digital signal processing block, including a decimation filter, a channel selection filter and a digital programmable gain amplifier (PGA), is implemented in the same process. The decimation filter is based on a polyphase IIR filter with a decimation ratio of 5, while the channel selection filter is based on two path lattice wave digital IIR filter. The ADC achieves 69.95 dB SNR and 66.85 dB SNDR over a 4 MHz bandwidth with a sampling frequency of 100 MHz. The fabricated $Delta Sigma$ ADC and the digital signal processing block occupy 0.53$~$mm$^2$ and 0.09 mm$^{2}$, and consume 11.76 mW per channel.      

A 1.5-V 45-mW direct-conversion WCDMA receiver IC in 0.13-/spl mu/m CMOS

A 2-GHz direct-conversion receiver for wide-band code division multiple access (WCDMA) is presented. It includes two low-noise amplifiers (LNAs), an I/Q demodulator, and two sixth-order baseband channel select filters with programmable gain. Quadrature local oscillator (LO) signals are generated on chip in a frequency divider flip-flop. An external interstage filter between the LNAs rejects transmitter leakage to relax demodulator linearity requirements. A low-voltage demodulator topology improves linearity as well as demodulator output pole accuracy. The active-RC baseband filter uses a programmable servo loop for offset compensation and provides an adjacent channel rejection of 39 dB. Programmable gain over 71-dB range in 1-dB steps is merged with the filter to maximize dynamic range. An automatic on-chip frequency calibration scheme provides better than 1.5% corner frequency accuracy. The receiver is integrated in a 0.13-/spl mu/m CMOS process with metal-insulator-metal (MIM) capacitors. Measured receiver performance includes a 6.5-dB noise figure, IIP2 of +27 dBm, and IIP3 of -8.6 dBm. Power consumption is 45 mW.     

A CMOS 5 nV$/surd $Hz 74-dB-Gain-Range 82-dB-DR Multistandard Baseband Chain for Bluetooth, UMTS, and WLAN

An analog baseband chain for a multistandard (Bluetooth, WCDMA/UMTS, and WLAN) reconfigurable receiver in a 0.13 mum CMOS occupying 1.65 mm² is presented. The circuit consists of an open-loop programmable-gain amplifier (PGA1), an active-G_m-RC low-pass filter (LPF), and a closed-loop programmable-gain amplifier (PGA2). The chain gain can be programmed in the range -6 divide 68 dB, while the input-referred noise (IRN) is 5 nV/radicHz. A dynamic range (DR) larger than 82 dB is achieved for a 1% total harmonic distortion (THD). The current consumption is minimized and adjusted for the different operation conditions, down to 11 mA for the full chain.     

A 10-bit 44-MS/s 20-mW configurable time-interleaved pipeline ADC for a dual-mode 802.11b/Bluetooth receiver

This work presents a configurable time-interleaved pipeline architecture as an efficient solution for the ADC design in high data rate multi-standard radios. The ADC is implemented in a 0.25-/spl mu/m BiCMOS process as part of an integrated dual mode 802.11b/Bluetooth direct conversion receiver. Its structure can be configured to accommodate the different sampling rate and dynamic range requirements of both standards. The different techniques employed at the system and circuit levels to optimize the power consumption are described. An on-line digital calibration scheme is also incorporated to assure the conversion linearity and reduce mismatch among the parallel branches. The proposed ADC is a switched-capacitor implementation occupying an area of 2.1 mm/sup 2/. It achieves 60 dB/64 dB dynamic range at 44 MHz/11 MHz sampling frequency with a power consumption of 20.2 mW/14.8 mW for the 802.11b/Bluetooth baseband signals.     

Bandpass Sigma–Delta Modulator Employing SAW Resonator as Loop Filter

Continuous-time bandpass (BP) sigma-delta modulators (SigmaDeltaMs) employing surface acoustic wave (SAW) resonators as loop filters are presented. Compared with the loop filters realized with G_m-C and LC resonators, the SAW resonator has the advantage of high-Q factor, wide resonant frequency range and accurate resonant frequency without the need for automatic tuning. With the proposed anti-resonance cancellation and loop filter phase compensation techniques, a second- and a fourth-order BP SigmaDeltaMs are demonstrated in a 0.35-mum CMOS technology. Both modulators are tested with 47.3-MHz off-chip SAW resonators. The second-order modulator attains a dynamic range of 57 dB and peak signal-to-noise distortion ratio (SNDR) of 54 dB and the fourth-order one achieves a dynamic range of 69 dB and peak SNDR of 66 dB, both in a 200-kHz signal bandwidth. The fourth-order modulator is also measured in a 3.84-MHz signal bandwidth and achieves a dynamic range of 52.5 dB and peak SNDR of 50 dB, an effective 8-bit resolution     

A 6-Bit 1.6-GS/s Low-Power Wideband Flash ADC Converter in 0.13-$mu$ m CMOS Technology

In this work, a new termination technique for the averaging network of the flash analog-to-digital converter (ADC) input preamplifiers is devised. The proposed technique eliminates the over-range voltage headroom consumed by the dummy preamplifiers and therefore, the input capacitance and power dissipation of the ADC is reduced. This technique is applied to the design of a 6-bit 1.6-GS/s flash ADC in 0.13-$mu$ m CMOS technology. The measured peak INL and DNL are 0.42 LSB and 0.49 LSB, respectively. The ADC achieves an effective resolution bandwidth (ERBW) of 800 MHz and an SNDR of 30 dB at 1.45-GHz input signal frequency while consuming 180 mW.      

A 0.7-V 870-$mu$ W Digital-Audio CMOS Sigma-Delta Modulator

This paper introduces a power-efficient, chopper-stabilized switched-capacitor sigma-delta $(SigmaDelta)$ modulator that combines delayed input feedforward and single-comparator tracking multi-bit quantization to achieve high-precision, low-voltage analog-to-digital (A/D) conversion. An experimental prototype of the proposed architecture has been integrated in a 0.18-$mu{hbox {m}}$ CMOS technology. The prototype operates from a 0.7-V supply voltage with a sampling rate of 5 MSamples/sec and consumes only 870$ muhbox{W}$ of total power. The converter achieves a dynamic range of 100 dB, a peak signal-to-noise ratio (SNR) of 100 dB and a peak signal-to-noise and distortion ratio (SNDR) of 95 dB for a 25-kHz signal bandwidth.      

A continuous-time /spl Sigma//spl Delta/ ADC with increased immunity to interferers

Receivers are being digitized in a quest for flexibility. Analog filters and programmable gain stages are being exchanged for digital processing at the price of a very challenging ADC. This paper presents an alternative solution where the filter and programmable gain functionality is integrated into a /spl Sigma//spl Delta/ ADC. The novel filtering ADC is realized by adding a high-pass feedback path to a conventional /spl Sigma//spl Delta/ ADC while a compensating low-pass filter in the forward path maintains stability. As such, the ADC becomes highly immune to interferers even if they exceed the maximum allowable input level for the wanted channel. As a consequence, the ADC input range can be programmed dynamically to the level of the wanted signal only. This results in an input-referred dynamic range of 89 dB in 1-MHz bandwidth and an intentionally moderate output signal-to-noise-and-distortion ratio of 46-59 dB (depending on the programmed gain). The merged functionality enables a better overall power/performance balance for the receiver baseband. The design consumes less than 2 mW and active area is 0.14 mm/sup 2/ in a 0.18-/spl mu/m digital CMOS technology.     

A sub-sampling 4-bit 1.056-GS/s flash ADC with a novel track and hold amplifier for an IR-UWB receiver

A sub-sampling 4-bit 1.056-GS/s flash ADC with a novel track and hold amplifier(THA) in 0.13μm CMOS for an impulse radio ultra-wideband(IR-UWB) receiver is presented.The challenge is in implementing a sub-sampling ADC with ultra-high input signal that further exceeds the Nyquist frequency.This paper presents,to our knowledge for the second time,a sub-sampling ADC with input signals above 4 GHz operating at a sampling rate of 1.056 GHz.In this design,a novel THA is proposed to solve the degradation in amplitude and improve the linearity of signal with frequency increasing to giga Hz.A resistive averaging technique is carefully analyzed to relieve noise aliasing.A low-offset latch using a zero-static power dynamic offset cancellation technique is further optimized to realize the requirements of speed,power consumption and noise aliasing.The measurement results reveal that the spurious free dynamic range of the ADC is 30.1 dB even if the input signal is 4.2 GHz sampled at 1.056 GS/s.The core power of the ADC is 30 mW,excluding all of the buffers,and the active area is 0.6 mm~2.The ADC achieves a figure of merit of 3.75 pJ/conversion-step.     

A 77-dB Dynamic Range, 7.5-MHz Hybrid Continuous-Time/Discrete-Time Cascaded $Sigma Delta$ Modulator

Although SigmaDelta modulators have largely been implemented as discrete-time (DT) circuits, a continuous-time (CT) approach offers significant advantages for realizing high-accuracy A/D converters at signal bandwidths where technology considerations may impose significant constraints. A CT design allows for relaxed amplifier unity-gain frequency and power requirements, which can enable the realization of high-resolution modulators with bandwidths of several MHz or more at low power. It also provides the advantage of inherent anti-aliasing filtering. This paper introduces a hybrid CT/DT SigmaDelta modulator for A/D conversion that combines the benefits of CT and DT circuits, while mitigating the challenges associated with CT design. The second-order first stage of a two-stage cascade is implemented in CT, while the first-order second stage is a DT circuit. An experimental prototype of the proposed modulator, integrated in 0.18-mum CMOS technology, operates from a 1.2-V analog supply to allow for easier migration to a 0.13-mum or 90-nm CMOS technology. The prototype achieves a dynamic range of 77 dB, a peak SNR of 71 dB, a peak SNDR of 67 dB, and worst-case anti-aliasing filtering of 48 dB for a signal bandwidth of 7.5 MHz and a sampling rate of 240 MHz. The total power dissipation is 89 mW, including 63.6 mW of analog power.     

A 1.5-V 12-bit power-efficient continuous-time third-order /spl Sigma//spl Delta/ modulator

This paper presents the design strategy, implementation, and experimental results of a power-efficient third-order low-pass /spl Sigma//spl Delta/ analog-to-digital converter (ADC) using a continuous-time (CT) loop filter. The loop filter has been implemented by using active RC integrators. Several power optimizations, design requirements, and performance limitations relating to circuit nonidealities in the CT modulator are presented. The influence of the low supply voltage on the various building blocks such as the amplifier as well as on the overall /spl Sigma//spl Delta/ modulator is discussed. The ADC was implemented in a 3.3-V 0.5-/spl mu/m CMOS technology with standard threshold voltages. Measurements of the low-power 1.5-V CT /spl Sigma//spl Delta/ ADC show a dynamic range and peak signal-to-noise-plus-distortion ratio of 80 and 70 dB, respectively, in a bandwidth of 25 kHz. The measured power consumption is only 135 /spl mu/W from a single 1.5-V power supply.     

A "divide and conquer" technique for implementing wide dynamic range continuous-time filters

This paper presents a technique for implementing analog filters with wide dynamic range and low power dissipation and chip area. The desired dynamic range of the filter is divided into subranges, each covered by a different filtering path optimized specifically for this subrange. This results in small admittance levels for the individual filtering paths and correspondingly small power dissipation and chip area. The system provides undisturbed output during range switching, contrary to conventional automatic gain control (AGC)/filter arrangements that generate disturbances every time the gain of the AGC changes. We also report on a low-noise highly linear CMOS transconductor useful for high-frequency applications. A chip implementing the ideas of this paper was fabricated in a 0.25-/spl mu/m digital CMOS process. The intended application of the filter is channel selection in an 802.11a/Hiperlan2 Wireless Ethernet receiver. The chip dissipates 9 mA, occupies an area of 0.7 mm/sup 2/, and maintains a signal/(noise + IM3 distortion) ratio of at least 33 dB over a 48-dB signal range, with good blocker immunity. This performance represents at least an order of magnitude improvement over existing channel selection filters, even those that do not achieve disturbance-free operation.     

An IF-to-Baseband Σ∆ Modulator for AM/FM/IBOC Radio Receivers With a 118 dB Dynamic Range

A single-bit fifth-order complex continuous-time IF-to-baseband SigmaDelta modulator for AM/FM/IBOC receivers is presented. The input IF is 10.7 MHz and the sampling frequency is 41.7 MHz. The modulator achieves a dynamic range of 118dB in AM mode (3 kHz BW), 98dB in FM mode (200 kHz BW), and 86dB in IBOC mode (500 kHz BW). The modulator's high dynamic range enables the realization of an AM radio receiver without a VGA and without an AM channel-selection filter, thereby reducing system complexity and cost. The elimination of the VGA also improves the sensitivity and the overall noise figure of the receiver. The modulator's spurious free dynamic range is 88 dB in the bandwidth from 25 to 525 kHz. The IM2 distance is 92 dB, and the IM3 distance is 91 dB. The ADC was fabricated in a one-poly five-metal 0.18-mum CMOS process with an active area of 6.0mm². It consumes 210 mW from a 1.8-V supply     

A 15-bit Linear 20-MS/s Pipelined ADC Digitally Calibrated With Signal-Dependent Dithering

Pseudo-random dithers have been used to measure capacitor mismatch and opamp gain errors of the pipelined analog-to-digital converter (ADC) in background and to calibrate them digitally. However, this error measurement suffers from signal range reduction and long signal decorrelation time. A signal-dependent dithering scheme allows the injection of a large dither without sacrificing the signal range and shortens the signal decorrelation time. A 1.5-bit multiplying digital-to-analog converter (MDAC) stage is modified for signal-dependent dithering with two additional comparators, and its capacitor mismatch and gain errors are measured and calibrated as one error. When sampled at 20 MS/s, a 15-bit prototype ADC achieves a spurious-free dynamic range of 98 dB with 14.5-MHz input and a peak signal-to-noise plus distortion ratio of 73 dB with 1-MHz input. Integral nonlinearity is improved from 25 to 1.3 least significant bits (LSBs) after calibrating the first six stages. The chip is fabricated in 0.18-mu CMOS process, occupies an active area of 2.3 x 1.7 mm² , and consumes 285 mW at 1.8 V.     

A 750-MHz 6-b Adaptive Floating-Gate Quantizer in 0.35-$mu{hbox {m}}$ CMOS

A 6-b 750-MS/s flash analog-to-digital converter (ADC) uses nonvolatile analog storage for reference levels and achieves a signal-to-noise-plus-distortion ratio (SNDR) and a spurious-free dynamic range of 37.2 and 48.6 dB, respectively. The architecture comprises an array of adaptive floating-gate comparators that enables storage and programming of reference levels, eliminating the need for resistive ladders. Reference levels may be programmed either manually by the user or autonomously during normal analog-to-digital conversion. Autonomous programming achieves histogram equalization by adjusting reference levels for finer resolution and greater sensitivity at frequently visited signal values. When programmed manually, the ADC achieves 34.3-dB SNDR at 750 MS/s for input frequencies up to 2.07$times$ Nyquist rate, with a differential full-scale input range of 1 V. We observe integral nonlinearity and differential nonlinearity of less than 0.27 least significant bit at the Nyquist rate. One-month continuous operation shows no signs of reference-level drift due to charge leakage and maintains a constant bit error rate of $2.93times 10^{-9}/hbox{sample}$.      

A 9 mW Highly-Digitized 802.15.4 Receiver Using Bandpass $SigmaDelta$ ADC and IF Level Detection

A low power (9 mW) highly-digitized 2.4 GHz receiver for sensor network applications (IEEE 802.15.4 LR-WPAN) is realized by a 0.18 $mu{rm m}$ CMOS process. We adopted a novel receiver architecture adding an intermediate frequency (IF) level detection scheme to a low-power complex fifth-order continuous-time (CT) bandpass $SigmaDelta$ modulator in order to digitalize the receiver. By the continuous-time bandpass architecture, the proposed $SigmaDelta$ modulator requires no additional anti-aliasing filter in front of the modulator. Using the IF detector, the achieved dynamic range (DR) of the overall system is 95 dB at a sampling rate of 64 MHz. This modulator has a bandwidth of 2 MHz centered at 2 MHz. The power consumption of this receiver is 9.0 mW with a 1.8 V power supply.      

Cascaded Complex ADCs With Adaptive Digital Calibration for $I/Q$ Mismatch

A complex analog-to-digital converter (ADC) intended for digital intermediate frequency (IF) receiver applications digitizes analog signals at IFs with excellent power/bandwidth efficiency. However, it is vulnerable to mismatches between its in-phase and quadrature (I/Q) paths that can dramatically degrade its performance. The proposed solution mitigates I/Q mismatch effects using a complex sigma-delta (SigmaDelta) modulator cascaded with 9-bit pipeline converters in each of the I and Q paths. The quantization noise of the first stage complex modulator is eliminated using an adaptive scheme to calibrate finite-impulse response digital filters in the digital noise-cancellation logic block. Although low-pass SigmaDelta cascade ADCs are widely used because of their inherent stability and high-order noise shaping, the complex bandpass cascade architecture introduced herein maintains these advantages and doubles the noise shaping bandwidth. Digital calibration also reduces the effects of analog circuit limitations such as finite operational amplifier gain, which enables high performance and low power consumption with high-speed deep-submicrometer CMOS technology. Behavioral simulations of the complex SigmaDelta/pipeline cascade bandpass ADC using the adaptive digital calibration algorithm predict a signal-to-noise ratio (SNR) of 78 dB over a 20-MHz signal bandwidth at a sampling rate of 160 MHz in the presence of a 1% I/Q mismatch.     

Dual-band RF receiver for GPS-L1 and compass-B1 in a 55-nm CMOS

A fully integrated dual-band RF receiver with a low-IF architecture is designed and implemented for GPS-L 1 and Compass-Bl in a 55-nm CMOS process. The receiver incorporates two independent IF channels with 2 or 4 MHz bandwidth to receive dual-band signals around 1.57 GHz respectively. By implementing a flexible frequency plan, the RF front-end and frequency synthesizer are shared for the dual-band operation to save power consumption and chip area, as well as avoiding LO crosstalk. A digital automatic gain control （AGC） loop is utilized to improve the receiver＇s robustness by optimizing the conversion gain of the analog-to-digital converter （ADC）. While drawing about 20 mA per channel from a 1.2 V supply, this RF receiver achieves a minimum noise figure （NF） of about 1.8 dB, an image rejection （IMR） of more than 35 dB, a maximum voltage gain of about 122 dB, a gain dynamic range of 82 dB, and an maximum input-referred 1 dB compression point of about -36.5 dBm with an active die area of 1.5 × 1.4 mm2 for the whole chip.     

一种基于电阻型数模转换器每级输出3位的6-bit 410-MS/s单通道异步逐次逼近模数转换器

该设计采用SMIC 65-nm CMOS工艺,实现了一款可应用于超宽带通信领域的单通道低功耗6位410-MS/s异步逐次逼近模数转换器(SAR ADC)。通过采用电阻型数模转换器、每级输出3位数字码字结构,以及改进的异步控制逻辑,该ADC在370-MS/s采样率时,无杂散动态范围(SFDR)达到41.95-dB,信号噪声失真比(SNDR)达到28.52-dB。在采样率为410MS/s时,该设计仍能达到40.71-dB的SFDR和30.02-dB的SNDR。通过动态比较器的使用,实现了低功耗设计。测试结果表明,在410-MS/s采样率下,电路总功耗为2.03mW,对应的品质因子(FOM)为189.17fJ/step。