Development of a method for detection and trend analysis of research fronts built by lexical or cocitation analysis

Detecting homogeneous areas in research networks is a very common feature of bibliometric analysis, either for academic or policy purposes. The method presented here combines structural analysis and trend detection, by operating on a thick-slice of time, starting from co-citation or co-word analysis (applications of either type have already been carried on). Significance of trend of clusters is partially addressed, through an analysis of publication delays. Examples are given on a co-citation analysis in the field of astrophysics (1986–1989).Paper presented at the Fourth International Conference on Bibliometrics, Informetrics and Scientometrics in Berlin (Germany), September 11–15, 1993.     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

IN-713C characteristic properties optimized through different heat treatments

The strength of a nickel-based superalloy hardened through precipitation is related to the volume fraction, particle size and distribution of the precipitated phase, . These parameters may vary as a result of heat treatment, or high-temperatures service. The information obtained, describing the influence of time and temperature on the precipitated phase, , is of special importance owing to its technological application at high temperatures. Dissolution or precipitation kinetics are such that the volume-fraction balance of the phase is quickly established at an ageing temperature given by successive changes due only to the particle growth. The results of the present study describe heat-treatment effects on size and distribution of the phase, and precipitated carbides ageing of a nickel-based superalloy (IN-713C). These on ageing studies at a certain temperature show that the kinetic growth of particles by controlled diffusion follows that r t ^1/3 law.     

Liquid phase sintering of RE2O3: YSZ ceramics Part I Grain growth and expelling of the grain boundary glass phase

Experiments on silicate liquid phase sintering of YSZ ceramics with addition of 0.5 mol% of rare earth ions have been done in order to study the effect of these ions on the kinetics of grain growth and the expulsion of glass through the grain boundaries. Kinetics follow a third power law in the following order YPr>YPrEr>YY>YEr. The expelled glass does not spread over the ceramic grains and its mass is inversely related to grain size. Glass phase separation inside the grain boundaries is found to be a necessary condition for glass expulsion.     

Influence of pore volume on laser performance of Nd : YAG ceramics

For present study, 1.1 at% Nd-doped YAG ceramics with a controlled pore volume (150–930 vol ppm) were fabricated by a solid-state reaction method using high-purity powders. The scattering coefficients of Nd:YAG ceramics, obtained from Fresnel' equation, increased simply with increases in the pore volume. The cw laser output power of Nd:YAG ceramics was clearly related to the scattering coefficients of the specimens examined in the present works, which in turn were affected on the pore volume. The effective scattering coefficients of Nd:YAG ceramics with a pore volume of 150 vol ppm were nearly equivalent to those of a 0.9 at%Nd:YAG single crystal by Czochralski method. As the exciting power was increased under excitation by an 808-nm diode laser, however, the laser output power of the Nd:YAG ceramics exceeded that of the Nd:YAG single crystal because of the fairly large amount of Nd additives. The lasing performance of the Nd:YAG ceramics changed drastically with change in pore volume. On the other hand, lasing performance was not affected by the existence of grain boundaries in the polycrystalline Nd:YAG ceramics.     

Martensitic transformations in Ti-Mo alloys

A detailed investigation has been made of the structure of alloys of the Ti-Mo system containing up to 10wt% Mo, water-quenched from the-phase region. With increase in molybdenum content, the martensite structure changes from hexagonal () to orthorhombic () at 4 wt% Mo, and at 10 wt% Mo, the structure is completely retained . For alloy compositions <4 wt% Mo, there is a diffusional component in the transformation of the -phase at the quench rates employed. There is a transition, with increase in molybdenum content, in morphology (from massive to acicular) and in substructure (from dislocations to twins). However, the transitions in crystallography, morphology and sub-structure are not directly related to one another except for an abrupt loss of dislocation substructure at the/ transition. The to crystallographic transition has the characteristics of a second order transformation, and evidence has been obtained of the existence of a spinodal within the metastable orthorhombic system. The orthorhombic martensites of Ti-6 and 8 wt% Mo decompose during quenching producing a fine modulated structure within the martensite plates, consistent with a proposed spinodal mode of decomposition.     

Thermal Expansion and Isothermal Compressibility of TlIn1 – xNdxSe2 (0 ≤ x≤ 0.08) Crystals

The thermal expansion coefficient () and isothermal compressibility ( _T ) of TlIn_{1 – x} Nd _x Se₂(0 x 0.08) crystals were measured between 77 and 400 K. In the range 77–160 K, both and _T increase with temperature, the increase in being much steeper. At higher temperatures, and _T change very little. The observed composition dependences of and _T are interpreted in terms of energy-band structure.     

Agglomeration problems in the formation of FeSi2 from Fe-Si thin-film couples

The agglomeration process that occurs during annealing of thin Fe films (<200 nm) on Si substrates has been studied. Agglomeration occurred on uncapped films prior to silicide formation. Capping layers of SiO₂, or more appropriately Si-SiO₂, have been used to minimize agglomeration effects. Continuous thin films of -FeSi₂ have been grown on 11 1 and 100 oriented substrates. Preferred growth of (202) and (220) suicide planes on 111 Si has been obtained, while preferential growth was not observed on 100 Si.     

The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

Low temperature heat release,sound velocity and attenuation,specific heat and thermal conductivity in polymers

We have measured the long time (t = 5 to 200 h) heat release of Polymethylmethacrylate (PMMA) and Polystyrene (PS) at 70 mK T 300 mK. After cooling from a charging temperature of 80 K the heat release in PMMA shows a t^–1 dependence in the measured time and temperature ranges in agreement with the tunneling model. In contrast, for PS we observe strong deviations from at ^–1 dependence and a factor of ten smaller heat release than in PMMA in apparent contradiction to specific heat and thermal conductivity data for PS. To compare the heat release with other low temperature properties and to verify the consistency of the tunneling model we have measured also the acoustical properties (sound velocity and attentuation), the specific heat and the thermal conductivity of PMMA and PS in the temperature range 70mKT 100 mK, 70mKT200 mK and 0.3 KT4K, respectively. We show that the anomalous time dependence of the heat release of PS is due to the thermally activated relaxation of energy states with excitation energies above 15 K.     

Convection in a shallow laterally heated cavity with conducting boundaries

Shallow cavity flows driven by horizontal temperature gradients are analysed over a range of Rayleigh numbersR and Prandtl numbers , whereR is comparable in size to the aspect ratioL(1). Eigenvalue calculations show the existence of a critical Prandtl number R > R _c (), below which the parallel core-flow structure is destroyed for Rayleigh numbersR>R _c(). For other Rayleigh numbers and Prandtl numbers the horizontal scale of influence of the end walls of the cavity is determined.     

Magnetic Properties of High-Resistivity CdTe〈In〉 and CdTe〈Cl〉 Crystals

The magnetic susceptibility of high-resistivity CdTeIn and CdTeCl crystals was measured between 4.2 and 300 K. The susceptibility was found to vary anomalously with temperature. Below 50 K, all the samples were paramagnetic. The observed anomalies are interpreted in terms of donor–acceptor pairs formed by native defects and dopant or uncontrolled impurity atoms. The effect of doping on the 300-K is related to the Van Vleck paramagnetic contribution resulting from the local electric fields of X_i–V _Cdand In_i–V _Cddefect complexes. In CdTeCl, this contribution is insignificant.     

Rheological properties of aqueous silicon nitride suspensions

The effect of surface modification of Si₃N₄ particle on the colloidal behavior and the rheological properties of aqueous Si₃N₄ suspensions under steady and oscillatory conditions are investigated in detail. Due to the decrease of the oxidizing level, the isoelectric point (IEP) of the modified particle shifts to basic region gently. Attempts have been made to apply rheological models to the suspensions with various solid volume fraction (). For the as-received suspensions, the Sisco model provides the best fit in the range of 0.30 while the Casson model in 0.35 0.45. The shear behavior of modified suspensions fits to Sisco model in the range of 0.40 and Casson model in 0.45 0.54. The rheological behavior of modified suspensions is improved efficiently. The critical strain decreases and the linear viscoelastic regime narrows continuously with increasing solid concentration. For the modified suspensions, the linear viscoelastic regime broadens and the corresponding elastic modulus decreases sharply. With increasing solid concentration, the characteristic frequency shifts toward lower frequencies and the suspension transforms from more viscous to more elastic.     

Solution of thermal conductivity problems with boundary condition of the third kind and arbitrary coordinate and time dependence of the biot number

An analytical solution of the thermal conductivity problem with boundary conditions of the third kind and arbitrary coordinate and time dependence of the Biot number is found in the form of a converging series of quadratures.Notation , z dimensionless coordinates - dimensionless temperature - Q dimensionless volume heat-liberation density per unit time - Fo=/² Fourier number - Bi₁(, Fo)=(, Fo) · / Biot number - thermal diffusivity coefficient - plate thickness - time - (, Fo) heat-liberation coefficient - thermal conductivity coefficient - i summation index - Jo zero order Bessel function of the first kind Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 536–540, September, 1981.     

Grain boundary sensitization and desensitization during the ageing of 316L(N) austenitic stainless steels

Two casts of type 316L(N) austenitic stainless steel have been solution treated for 1 h at 1070 C, air-cooled, then aged for up to 20 000 h at temperatures between 550 C and 750 C. Grain boundary precipitation of the M₂₃C₆ phase occurs, and the Cr composition profile normal to the grain boundaries has been determined at high resolution by an analytical electron microscope. The data have been fitted firstly to collector plate models, which indicated that some of the material was in the process of desensitization, or healing, indicated by a rise in the boundary Cr content. The data were then fitted to a model of the Cr profile as a function of ageing treatment in the healing regime, and a good correlation was obtained.     

Theory of RF SQUIDs Operating in the Presence of Large Thermal Fluctuations

A comprehensive analytical theory is presented for non-hysteretic RF SQUIDs operating in the adiabatic mode in the presence of large thermal fluctuations. When 1 ( = 2LI_c/₀ is the hysteresis parameter, L is the SQUID inductance, I_c is the critical current of the Josephson junction, and ₀ is the flux quantum) the theory is applicable also for RF SQUIDs operating in the non-adiabatic mode. In contrast to previous theories in which the noise is treated perturbatively and which therefore are applicable only if the product 1 ( = 2k_BT/ ₀ I_c is the noise parameter, k_B is the Boltzmann constant, and T is the absolute temperature)—the case of small thermal fluctuations—the present theory is valid for around unity or higher. In the limit 0 the theory reproduces the results of small thermal fluctuations theories. It has been found that in the presence of large thermal fluctuations the screening current in the SQUID inductance is suppressed by a factor that increases with increasing . Taking into account this new basic fact, all SQUID characteristics (output signal, transfer function, noise spectral density and energy sensitivity) have been recalculated and a good agreement with experimental data has been obtained. It has been also found that RF SQUIDs can be operated with substantially higher values of the inductance and of the noise parameter than DC SQUIDs. These two aspects, which are of particular importance at liquid nitrogen temperature, make high T_c RF SQUIDs very attractive.     

Irreversibilites in science and technology networks: An empirical and analytical approach

The theory of autopoiesis, i.e., self-referentiality in the operation of the system, provides us with a production rule for change in the structure of the network. Using information theory, a model system is developed to study the relative likelihood of dynamic transitions: various senses of irreversibility (emergence, and path dependency) are disinguished. A test for path dependency is applied to two sets of empirical data which supposedly reflect historical discontinuities: the budget of theFraunhofer Gesellschaft, and the citation network among AIDS research related journals. The model for the interaction between self-referential developments and goal-referential boundary conditions is further specified, using the example of technological trajectories and selection environments.     

A transmission-electron-microscopy study of a face-centred-cubic phase in an Al-Li-Cu-Mg-Zr alloy

Icosahedral T₂ phases can form either by solid-state precipitation or during solidification in Al-Li-Cu-Mg alloys. The T₂ phase forming during solidification can transform to an R phase at high annealing temperatures. The T₂ phase forming by solid-state precipitation coexists with the Y phase, which has a face-centred cubic (f.c.c.) structure with lattice parameter a2.0 nm and can form microtwins with the twin plane of (111). The orientation relationships between the C phase and the T₂ phase are: i¯5Y0 1 1, Y1 1 3; i¯3Y1 1 1, Y1 2 3, Y1 1 5; Y2 3 5; i2Y0 1 1, Y1 1 1, Y1 1 2, Y1 1 3, Y1 1 5.     

Knudsen molecular flow in a channel with a small temperature difference at its ends

The thermomolecular pressure difference (TPD) of helium, argon, and krypton is measured in a packet of glass capillaries for temperatures 273 and 293 K at their ends in a 10–100 range of Knudsen numbers.Notation exponent of the thermomolecular pressure difference effect - Kn Knudsen number - rarefaction parameter - Q_T reduced thermal creep flux - Q_P reduced Poiseuille flux - C(_t) Cercignani-Lampis scattering kernel - R specular scattering kernel - (1 – ) fraction of specular reflection - _t accommodation coefficient of the tangential momentum - P_c, P_h gas pressure in the cold and hot volumes, respectively - coefficient of dynamic viscosity - m mass of gas molecules - k Boltzmann constant - D, L the capillary diameter and length, respectively Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 54, No. 5, pp. 719–724, May, 1988.     

Simulation of the Process of Water Freezing in a Round Pipe

The problem of freezing of pure water in a round pipe is treated with due regard for convection under asymmetric thermal boundary conditions in the absence of motion along the pipe. The problem is solved numerically using the control volume approach, SIMPLER algorithm, and the enthalpy method. Results are obtained for three Grashof (Gr) and six Biot (Bi) numbers: Gr = 1.55 × 10⁶, Bi = 0.305 (0 < ), Bi = 0.044 ( < 2); Gr = 1.24 × 10⁷, Bi = 0.610 (0 < ), Bi = 0.087 ( < 2); Gr = 9.89 × 10⁷, Bi = 1.220 (0 < ), Bi = 0.174 ( < 2). The correctness of calculation of the problem disregarding free-convection flows is analyzed.