Thermal resistance of screen mesh wick heat pipes using the water-based Al2O3 nanofluids

In the present study, the effect of nanofluids on the thermal performance of heat pipes is experimentally investigated by testing circular screen mesh wick heat pipes using water-based Al₂O₃ nanofluids with the volume fraction of 1.0 and 3.0 Vol.%. The wall temperature distributions and the thermal resistances between the evaporator and the adiabatic sections are measured and compared with those for the heat pipe using DI water. The averaged evaporator wall temperatures of the heat pipes using the water-based Al₂O₃ nanofluids are much lower than those of the heat pipe using DI water. The thermal resistance of the heat pipe using the water-based Al₂O₃ nanofluids with the volume fraction of 3.0 Vol.% is significantly reduced by about 40% at the evaporator-adiabatic section. Also, the experimentally results implicitly show that the water-based Al₂O₃ nanofluids as the working fluid instead of DI water can enhance the maximum heat transport rate of the heat pipe. Based on the two clear evidences, we conclude that the major reason which can not only improve the maximum heat transport rate but also significantly reduce the thermal resistance of the heat pipe using nanofluids is not the enhancement of the effective thermal conductivity which most of previous researchers presented. Especially, we experimentally first observe the thin porous coating layer formed by nanoparticles suspended in nanofluids at wick structures. Based on the observation, it is first shown that the primary mechanism on the enhancement of the thermal performance for the heat pipe is the coating layer formed by nanoparticles at the evaporator section because the layer can not only extend the evaporation surface with high heat transfer performance but also improve the surface wettability and capillary wicking performance.     

Effect of nanofluids on reflood heat transfer in a long vertical tube

Experiments were conducted to investigate the effect of nanofluids on reflood heat transfer in a hot vertical tube. The nanofluids, which are produced by dispersing nano-sized particles in traditional base fluids such as water, ethylene glycol, and engine oil, are expected to have a reasonable potential to enhance a heat transfer. 0.1 volume fraction (%) Al₂O₃/water nanofluid was prepared by two-step method and 0.1 volume fraction (%) carbon nano colloid (CNC) was prepared by the process self-dispersing by carboxyl formed particle surface. Transmission electron microscopy (TEM) images are acquired to characterize the shape and size of Al₂O₃ and graphite nanoparticles. The dispersion behavior of nanofluids was investigated with zeta potential values. And then, the reflood tests have been performed using water and nanofluids. We have observed a more enhanced cooling performance in the case of the nanofluid reflood. Consequently, the cooling performance is enhanced more than 13 s and 20 s for Al₂O₃/water nanofluid and CNC.     

Numerical investigation on heat transfer and friction factor characteristics of laminar and turbulent flow in an elliptic annulus utilizing nanofluid

In this paper, a numerical investigation on heat transfer performance and flow fields of different nanofluids flows through elliptic annulus in a laminar and turbulent flow regimes. The three-dimensional continuity, Navier–Stokes and energy equations are solved by using finite volume method (FVM) and the SIMPLE algorithm scheme is applied to examine the effects of laminar and turbulent flow on heat transfer characteristics. This study evaluates the effects of four different types of nanoparticles, Al₂O₃, CuO, SiO₂ and ZnO, with different volume fractions (0.5–4%) and diameters (25–80 nm) under constant heat flux boundary condition using water as a base fluid were used. The Reynolds number of laminar flow was in the range of 200 ≤ Re ≤ 1500, while for turbulent flow it was in the range of 4000 ≤ Re ≤ 10,000. The results have shown that SiO₂–water nanofluid has the highest Nusselt number, followed by ZnO–water, CuO–water, Al₂O₃–water, and lastly pure water. The Nusselt number for all cases increases with the volume fraction but it decreases with the rise in the diameter of nanoparticles. In all configurations, the Nusselt number increases with Reynolds number. It is found that the glycerine–SiO₂ shows the best heat transfer enhancement compared with other tested base fluids.     

Stabilizer effect on CHF and boiling heat transfer coefficient of alumina/water nanofluids

We measured the critical heat flux (CHF) and boiling heat transfer coefficient (BHTC) of water-based Al₂O₃ (alumina) nanofluids. To elucidate the stabilizer effect on CHF and BHTC of alumina/water nanofluids, a polyvinyl alcohol (PVA) was used as a stabilizer. The plate copper heater (10 × 10 mm²) is used as the boiling surface and the concentration of alumina nanoparticle varies 0–0.1 vol.%. The results show that the BHTC of the nanofluids becomes lower than that of the base fluid as the concentration of nanoparticles increases while CHF of it becomes higher. It is found that the increase of CHF is directly proportional to the effective boiling surface area and the reduction of BHTC is mainly attributed to the blocking of the active nucleation cavity and the increase of the conduction resistance by the nanoparticle deposition on the boiling surface.     

Unconfined laminar nanofluid flow and heat transfer around a square cylinder

The momentum and forced convection heat transfer for a laminar and steady free stream flow of nanofluids past an isolated square cylinder have been studied numerically. Different nanofluids consisting of Al₂O₃ and CuO with base fluids of water and a 60:40 (by mass) ethylene glycol and water mixture were selected to evaluate their superiority over conventional fluids. Recent correlations for the thermal conductivity and viscosity of nanofluids, which are functions of particle volumetric concentration as well as temperature, have been employed in this paper. The simulations have been conducted for Pe = 25, 50, 100 and 200, with nanoparticle diameters of 30 and 100 nm and particle volumetric concentrations ranging from 0% to 4%. The results of heat transfer characteristics of nanofluid flow over a square cylinder showed marked improvement comparing with the base fluids. This improvement is more evident in flows with higher Peclet numbers and higher particle volume concentration, while the particle diameter imposes an adverse effect on the heat transfer characteristics. In addition, it was shown that for any given particle diameter there is an optimum value of particle concentration that results in the highest heat transfer coefficient.     

An experimental study on CHF enhancement in flow boiling using Al2O3 nano-fluid

The critical heat flux (CHF) is one of the most important thermal hydraulic parameters in heat transfer system design and safety analyses. CHF enhancement allows higher limits of operation conditions such that heat transfer equipment can be operated safely with greater margins and better economy. The application of nano-fluids is thought to have strong potential for enhancing the CHF. In this study, zeta potentials of Al₂O₃ nano-fluids were measured and flow boiling CHF enhancement experiments using Al₂O₃ nano-fluids were conducted under atmospheric pressure. The CHFs of Al₂O₃ nano-fluids were enhanced up to ～70% in flow boiling for all experimental conditions. Maximum CHF enhancement (70.24%) was shown at 0.01 vol% concentration, 50 °C inlet subcooling, and a mass flux of 100 kg/m² s. Inner surfaces of the test section tube were observed by FE–SEM and the zeta potentials of Al₂O₃ nano-fluids were measured before and after the CHF experiments.     

Thermal and fluid dynamic behaviors of confined laminar impinging slot jets with nanofluids

Heat transfer enhancement technologies play an important role in research and industrial fields; thus, they have been widely applied to many applications as in refrigeration, automotive, aerospace, and process industry. For example, heat transfer can be passively enhanced by increasing the thermal conductivity of the working fluids, adopting nanofluids, or actively by employing impinging jets.In this paper a numerical analysis on confined impinging slot jets working with pure water or water/Al₂O₃ based nanofluids is presented. The flow is laminar and a constant uniform temperature is applied on the target surface. The single-phase model approach has been adopted in order to describe the nanofluid behavior and different particle volume concentrations have been considered. Moreover, simulations have been performed for different geometric ratios in order to take into account the confining effects and Reynolds numbers. The behavior of the system has been analyzed in terms of average and local convective heat transfer coefficient, Nusselt number, and required pumping power profiles. Correlations for stagnation point and average Nusselt number for 100 ≤ Re ≤ 400, 0% ≤ ϕ ≤ 5% and 4 ≤ H/W ≤ 10 are provided.     

An experimental study on the heat transfer performance and pressure drop of TiO2-water nanofluids flowing under a turbulent flow regime

Nanofluid is a new class of heat transfer fluids engineered by dispersing metallic or non-metallic nanoparticles with a typical size of less than 100 nm in the conventional heat transfer fluids. Their use remarkably augments the heat transfer potential of the base liquids. This article presents the heat transfer coefficient and friction factor of the TiO₂-water nanofluids flowing in a horizontal double tube counter-flow heat exchanger under turbulent flow conditions, experimentally. TiO₂ nanoparticles with diameters of 21 nm dispersed in water with volume concentrations of 0.2–2 vol.% are used as the test fluid. The results show that the heat transfer coefficient of nanofluid is higher than that of the base liquid and increased with increasing the Reynolds number and particle concentrations. The heat transfer coefficient of nanofluids was approximately 26% greater than that of pure vol.%, and the results also show that the heat transfer coefficient of the nanofluids at a volume concentration of 2.0 vol.% was approximately 14% lower than that of base fluids for given conditions. For the pressure drop, the results show that the pressure drop of nanofluids was slightly higher than the base fluid and increases with increasing the volume concentrations. Finally, the new correlations were proposed for predicting the Nusselt number and friction factor of the nanofluids, especially.     

The particle thermal conductivity influence of nanofluids on thermal performance of the microtubes

The paper presents the numerical analysis on microchannel laminar heat transfer and fluid flow of nanofluids in order to evaluate the suitable thermal conductivity of the nanoparticles that results in superior thermal performances compared to the base fluid. The diameter ratio of the micro-tube was D_i/D_o = 0.3/0.5 mm with a tube length L = 100 mm in order to avoid the heat dissipation effect. The heat transfer rate was fixed to Q = 2 W. The water based Al₂O₃, TiO₂ and Cu nanofluids were considered with various volume concentrations ϕ = 1,3 and 5% and two diameters of the particles d_p = 13 nm and 36 nm. The analysis is based on a fixed Re and pumping power Π, in terms of average heat transfer coefficient and maximum temperature of the substrate. The results reveal that only the nanofluids with particles having very high thermal conductivity (λ_Cu = 401 W/m K) are justified for using in microcooling systems. Moreover, the analysis is sensitive to both the comparison criteria (Re or Π) and heat transfer parameters (h_ave or t_max).     

Thermophysical properties and heat transfer performance of Al2O3/R-134a nanorefrigerants

The past decade has seen the rapid development of nanofluids science in many aspects. In recent years, refrigerant-based nanofluids have been introduced as nanorefrigerants due to their significant effects over heat transfer performance. This study investigates the thermophysical properties, pressure drop and heat transfer performance of Al₂O₃ nanoparticles suspended in 1, 1, 1, 2-tetrafluoroethane (R-134a). Suitable models from existing studies have been used to determine the thermal conductivity and viscosity of the nanorefrigerants for the nanoparticle concentrations of 1 to 5 vol.%. The pressure drop, pumping power and heat transfer coefficients of nanorefrigerant in a horizontal smooth tube have also been investigated with the same particle concentration at constant velocity of 5 m/s and uniform mass flux of 100 kg/m² s. In this study, the thermal conductivity of Al₂O₃/R-134a nanorefrigerant increased with the augmentation of particle concentration and temperature however, decreased with particle size intensification. In addition, the results of viscosity, pressure drop, and heat transfer coefficients of the nanorefrigerant show a significant increment with the increase of volume fractions. Therefore, optimal particle volume fraction is important to be considered in producing nanorefrigerants that can enhance the performance of refrigeration systems.     

Effect of particle size on the convective heat transfer in nanofluid in the developing region

An experimental investigation on the convective heat transfer characteristics in the developing region of tube flow with constant heat flux is carried out with alumina–water nanofluids. The primary objective is to evaluate the effect of particle size on convective heat transfer in laminar developing region. Two particle sizes were used, one with average particle size off 45 nm and the other with 150 nm. It was observed that both nanofluids showed higher heat transfer characteristics than the base fluid and the nanofluid with 45 nm particles showed higher heat transfer coefficient than that with 150 nm particles. It was also observed that in the developing region, the heat transfer coefficients show higher enhancement than in the developed region. Based on the experimental results a correlation for heat transfer in the developing region has been proposed for the present range of nanofluids.     

Heat transfer and friction factor of water based TiO2 and SiO2 nanofluids under turbulent flow in a tube

The heat transfer coefficient and friction factor of TiO₂ and SiO₂ water based nanofluids flowing in a circular tube under turbulent flow are investigated experimentally under constant heat flux boundary condition. TiO₂ and SiO₂ nanofluids with an average particle size of 50 nm and 22 nm respectively are used in the working fluid for volume concentrations up to 3.0%. Experiments are conducted at a bulk temperature of 30 °C in the turbulent Reynolds number range of 5000 to 25,000. The enhancements in viscosity and thermal conductivity of TiO₂ are greater than SiO₂ nanofluid. However, a maximum enhancement of 26% in heat transfer coefficients is obtained with TiO₂ nanofluid at 1.0% concentration, while SiO₂ nanofluid gave 33% enhancement at 3.0% concentration. The heat transfer coefficients are lower at all other concentrations. The particle concentration at which the nanofluids give maximum heat transfer has been determined and validated with property enhancement ratio. It is observed that the pressure drop is directly proportional to the density of the nanoparticle.     

Experimental investigation of heat transfer and friction factor with water–propylene glycol based CuO nanofluid in a tube with twisted tape inserts

Convective heat transfer and friction factor characteristics of water/propylene glycol (70:30% by volume) based CuO nanofluids flowing in a plain tube are investigated experimentally under constant heat flux boundary condition. Glycols are normally used as an anti-freezing heat transfer fluids in cold climatic regions. Nanofluids are prepared by dispersing 50 nm diameter of CuO nanoparticles in the base fluid. Experiments are conducted using CuO nanofluids with 0.025%, 0.1% and 0.5% volume concentration in the Reynolds numbers ranging from 1000 < Re < 10000 and considerable heat transfer enhancement in CuO nanofluids is observed. The effect of twisted tape inserts with twist ratios in the range of 0 < H/D < 15 on nanofluids is studied and further heat transfer augmentation is noticed. The increment in the pressure drop in the CuO nanofluids over the base fluid is negligible but the experimental results have shown a significant increment in the convective heat transfer coefficient of CuO nanofluids. The convective heat transfer coefficient increased up to 27.95% in the 0.5% CuO nanofluid in plain tube and with a twisted tape insert of H/D = 5 it is further increased to 76.06% over the base fluid at a particular Reynolds number. The friction factor enhancement of 10.08% is noticed and increased to 26.57% with the same twisted tape, when compared with the base fluid friction factor at the same Reynolds number. Based on the experimental data obtained, generalized regression equations are developed to predict Nusselt number and friction factor.     

Heat transfer enhancement using Al2O3–water nanofluid for an electronic liquid cooling system

We have experimentally investigated the behaviour and heat transfer enhancement of a particular nanofluid, Al₂O₃ nanoparticle–water mixture, flowing inside a closed system that is destined for cooling of microprocessors or other electronic components. Experimental data, obtained for turbulent flow regime, have clearly shown that the inclusion of nanoparticles into distilled water has produced a considerable enhancement of the cooling block convective heat transfer coefficient. For a particular nanofluid with 6.8% particle volume concentration, heat transfer coefficient has been found to increase as much as 40% compared to that of the base fluid. It has also been found that an increase of particle concentration has produced a clear decrease of the heated component temperature. Experimental data have clearly shown that nanofluid with 36 nm particle diameter provides higher heat transfer coefficients than the ones of nanofluid with 47 nm particle size.     

Turbulent heat transfer and friction factor of Al2O3 Nanofluid in circular tube with twisted tape inserts

The thermophysical properties like thermal conductivity and viscosity of Al₂O₃ nanofluid is determined through experiments at different volume concentrations and temperatures and validated. Convective heat transfer coefficient and friction factor data at various volume concentrations for flow in a plain tube and with twisted tape insert is determined experimentally for Al₂O₃ nanofluid. Experiments are conducted in the Reynolds number range of 10,000–22,000 with tapes of different twist ratios in the range of 0 < H/D < 83. The heat transfer coefficient and friction factor of 0.5% volume concentration of Al₂O₃ nanofluid with twist ratio of five is 33.51% and 1.096 times respectively higher compared to flow of water in a tube. A generalized regression equation is developed for the estimation of Nusselt number and friction factor valid for both water and nanofluid in plain tube and with inserts under turbulent flow conditions.     

Rayleigh–Bénard convection of Al2O3/water nanofluids in a cavity considering sedimentation,thermophoresis, and Brownian motion

This paper aims to investigate the Rayleigh–Bénard convection of Al₂O₃/water nanofluids in a cavity considering the sedimentation, thermophoresis, and Brownian motion. For this purpose, a numerical simulation is carried out using finite volume method to obtain the flow patterns and heat transfer characteristics of nanofluid flow inside the cavity. The results are presented for volume fractions up to 4%, Rayleigh numbers between 10⁴ and 8 × 10⁴ where the temperature difference between top and bottom walls is between 2 and 10 °C. To validate the numerical solution, comparisons are made between the numerical results and experimental data available in the literature. The comparisons unfold that the results of numerical work are in a good agreement with the previous experimental results.     

Forced convective heat transfer of nanofluids in microchannels

Convective heat transfer coefficient and friction factor of nanofluids in rectangular microchannels were measured. An integrated microsystem consisting of a single microchannel on one side, and two localized heaters and five polysilicon temperature sensors along the channel on the other side were fabricated. Aluminum dioxide (Al₂O₃) with diameter of 170 nm nanofluids with various particle volume fractions were used in experiments to investigate the effect of the volume fraction of the nanoparticles to the convective heat transfer and fluid flow in microchannels. The convective heat transfer coefficient of the Al₂O₃ nanofluid in laminar flow regime was measured to be increased up to 32% compared to the distilled water at a volume fraction of 1.8 volume percent without major friction loss. The Nusselt number measured increases with increasing the Reynolds number in laminar flow regime. The measured Nusselt number which turned out to be less than 0.5 was successfully correlated with Reynolds number and Prandtl number based on the thermal conductivity of nanofluids.     

Experimental investigation and model development for thermal conductivity of α-Al2O3-glycerol nanofluids

In order to investigate the effect of nanoparticle volume fraction, nanoparticle size and temperature on the thermal conductivity of glycerol based alumina (α-Al₂O₃) nanofluids, a set of experiments were carried out for temperature ranging from 20 °C to 45 °C. The nanofluids contained α-Al₂O₃ nanoparticles of three different sizes (31 nm, 55 nm and 134 nm) were prepared by two-step method at volume fractions ranging from 0.5% to 4%. The experimental results show that α-Al₂O₃-glycerol nanofluids have substantially higher thermal conductivity than the base fluid and the maximum enhancement of the relative thermal conductivity was 19.5% for the case of 31 nm at 4% volume fraction. The data analyses indicated that the volume fraction and size of the nanoparticles have significant effects on the thermal conductivity ratio (TCR) of Al₂O₃-glycerol nanofluids, while the temperature has almost no significant effect on the data for range of this study. At room temperature, the effective thermal conductivity remains almost constant for 50 h at 4% volume fractions. The comparison of the obtained experimental data and predictions from some existing theoretical and empirical models reveals that the thermal conductivity ratio and its trend could not be accurately explained by the models in open literature. Consequently, a new empirical correlation based on the experimental data has been developed in this study.     

Thermal performance augmentation using water based Al2O3-gamma nanofluid in a horizontal shell and tube heat exchanger under forced circulation

Shell and tube heat exchanger is one of the most prevalent heat exchangers with a wide variety of industrial applications, i.e., power plants, chemical processes, marine industries, HVAC systems, cooling of hydraulic fluid and engine oil in heavy duty diesel engines and the like specifically where a need to heat or cool a large fluid volume exist and also higher-pressure use. In the present study, the effect of using Al₂O₃-water nanofluid on thermal performance of a commercial shell and tube heat exchanger with segmental baffles is assessed experimentally. For this purpose, Al₂O₃-gamma nanoparticles with 15 nm mean diameter (99.5% purity) and Sodium Dodecyl Benzene Sulphonate (SDBS) as surfactant are used to make aqueous Al₂O₃ nanofluid at three various volume fractions of nanoparticles (φ = 0.03, 0.14 and 0.3%). Indeed, in this paper the effect of some parameters of hot working fluid such as Reynolds number and volume concentration of nanoparticles on heat transfer characteristics, friction factor and thermal performance factor of a shell and tube heat exchanger under laminar flow regime is investigated. The results indicate a substantial increment in Nusselt number as well as the overall heat transfer coefficient of heat exchanger by enhancement of Reynolds number and it can be seen that, at a certain Reynolds number, heat transfer characteristics of heat exchanger increase as the nanoparticles volume concentration increases. Outcomes of the heat transfer evaluation demonstrate that applying nanofluids instead of base fluid lead to increment of Nusselt number up to 9.7, 20.9 and 29.8% at 0.03, 0.14 and 0.3 vol%, respectively. Likewise it is seen that at mentioned nanoparticles volume fractions, overall heat transfer coefficient of heat exchanger enhances around 5.4, 10.3 and 19.1%, respectively. In term of pressure drop, a little penalty is found by using nanofluid in the test section. Eventually a thermal performance assessment on the heat exchanger was conducted. According to the analysis results, utilizing nanofluid at minimum and maximum nanoparticles volume fractions (φ = 0.03 and 0.3%) results in average augmentation of around 6.5% and 18.9% in thermal performance factor (η) of the heat exchanger compared to the base liquid, respectively.     

Heat transfer enhancement of nanofluids in a double pipe heat exchanger with louvered strip inserts

The effect of using louvered strip inserts placed in a circular double pipe heat exchanger on the thermal and flow fields utilizing various types of nanofluids is studied numerically. The continuity, momentum and energy equations are solved by means of a finite volume method (FVM). The top and the bottom walls of the pipe are heated with a uniform heat flux boundary condition. Two different louvered strip insert arrangements (forward and backward) are used in this study with a Reynolds number range of 10,000 to 50,000. The effects of various louvered strip slant angles and pitches are also investigated. Four different types of nanoparticles, Al₂O₃, CuO, SiO₂, and ZnO with different volume fractions in the range of 1% to 4% and different nanoparticle diameters in the range of 20 nm to 50 nm, dispersed in a base fluid (water) are used. The numerical results indicate that the forward louvered strip arrangement can promote the heat transfer by approximately 367% to 411% at the highest slant angle of α = 30° and lowest pitch of S = 30 mm. The maximal skin friction coefficient of the enhanced tube is around 10 times than that of the smooth tube and the value of performance evaluation criterion (PEC) lies in the range of 1.28–1.56. It is found that SiO₂ nanofluid has the highest Nusselt number value, followed by Al₂O₃, ZnO, and CuO while pure water has the lowest Nusselt number. The results show that the Nusselt number increases with decreasing the nanoparticle diameter and it increases slightly with increasing the volume fraction of nanoparticles. The results reveal that there is a slight change in the skin friction coefficient when nanoparticle diameters of SiO₂ nanofluid are varied.