Effect of iron oxide (Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>) on the structural,optical, electrical,and dielectric properties of SrO–V<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

The oxide glass system of the composition (10 – x)SrO–xFe₂O₃–90V₂O₅, (x = 0, 2, 4, 6 and 8 mol %) were prepared by a standard melt quenching technique. The amorphous nature of the prepared glass was confirmed using X-ray diffraction technique. The infrared spectra of these glasses were recorded over a continuous spectral range (850–1500 cm^–1). The density of prepared sample was obtained by the Archimedes principle. The physical parameters of the glasses were also determined with respect to the composition. Density increases from 3.10 to 3.20 g/cm³, whereas the molar volume decreases with the increase in Fe₂O₃ concentration. In order to study optical properties, absorption spectra were measured at room temperature. Indirect optical energy band gap, optical dielectric constant, refractive index were calculated from optical energy band gap. The refractive index decreases gradually with the increase in Fe₂O₃ content due to increase of bridging oxygen’s. For temperatures from 300 to 500 K, the dc conductivity increased with the increasing Fe₂O₃ content. The dielectric properties like dielectric constant, dielectric loss factor and dielectric loss tangent investigated at the room temperature in the frequency range of 10 kHz to 1 MHz decreases with frequency. The dielectric behavior shows strong frequency as well as composition dependence.     

Speciation and Electronic Structure of La<Subscript>1−x</Subscript>Sr<Subscript>x</Subscript>CoO<Subscript>3−δ</Subscript> During Oxygen Electrolysis

Cobalt-containing perovskite oxides are promising electrocatalysts for the oxygen evolution reaction (OER) in alkaline electrolyzers. However, a lack of fundamental understanding of oxide surfaces impedes rational catalyst design for improved activity and stability. We couple electrochemical studies of epitaxial La_1?xSr_xCoO_3?δ films with in situ and operando ambient pressure X-ray photoelectron spectroscopy to investigate the surface stoichiometry, adsorbates, and electronic structure. In situ investigations spanning electrode compositions in a humid environment indicate that hydroxyl and carbonate affinity increase with Sr content, leading to an increase in binding energy of metal core levels and the valence band edge from the formation of a surface dipole. The maximum in hydroxylation at 40% Sr is commensurate with the highest OER activity, where activity scales with greater hole carrier concentration and mobility. Operando measurements of the 20% Sr-doped oxide in alkaline electrolyte indicate that the surface stoichiometry remains constant during OER, supporting the idea that the oxide electrocatalyst is stable and behaves as a metal, with the voltage drop confined to the electrolyte. Furthermore, hydroxyl and carbonate species are present on the electrode surface even under oxidizing conditions, and may impact the availability of active sites or the binding strength of adsorbed intermediates via adsorbate–adsorbate interactions. For covalent oxides with facile charge transfer kinetics, the accumulation of hydroxyl species with oxidative potentials suggests the rate of reaction could be limited by proton transfer kinetics. This operando insight will help guide modeling of self-consistent oxide electrocatalysts, and highlights the potential importance of carbonates in oxygen electrocatalysis.     

Preparation and electrochemical characterization of LiNi<Subscript>0.8</Subscript>Co<Subscript>0.2</Subscript>O<Subscript>2</Subscript> cathode material by a modified sol–gel method

LiNi_0.8Co_0.2O₂ cathode powders for lithium-ion batteries were prepared by a modified sol–gel method with citric acid as chelating agent and a small amount of hydroxypropyl cellulose as dispersant agent. The structure and morphology of LiNi_0.8Co_0.2O₂ powders calcined at various temperatures for 4 h in air were characterized by means of powder X-ray diffraction analyzer, scanning electron microscope, thermogravimetric analyzer and differential thermal analyzer, and Brunauer–Emmett–Teller specific surface area analyzer. The results show that LiNi_0.8Co_0.2O₂ powders calcined at 800 °C exhibit the best layered structure ordering and appear to have monodispersed particulates surface. In addition, the electrochemical properties of LiNi_0.8Co_0.2O₂ powders as cathode material were investigated by the charge–discharge and cyclic voltammetry studies in a three-electrode test cell. The initial charge–discharge studies indicate that LiNi_0.8Co_0.2O₂ cathode material obtained from the powders calcined at 800 °C shows the largest charge capacity of 231 mAh g⁻¹ and the largest discharge capacity of 191 mAh g⁻¹. And, the cyclic voltammetry studies indicate that Li⁺ insertion and extraction in LiNi_0.8Co_0.2O₂ powders is reversible except for the first cycle.     

Microwave-assisted synthesis and characterization of new cathodic material for solid oxide fuel cells: La0.3Ca0.7Fe0.7Cr0.3O3−δ

In this work, we examine the benefits of alternative powder processing methods, with a primary focus on microwave-based synthesis, that could both lower material manufacturing costs and further enhance cathode performance for solid oxide fuel cell applications. La_0.3Ca_0.7Fe_0.7Cr_0.3O_3−δ (LCFCr), formed using conventional solid-state methods, has been shown in earlier work to be a very promising catalyst for the oxygen reduction reaction. To further increase its performance, microwave methods were used to increase the surface area of LCFCr and to decrease the synthesis time. It was found that the material could be obtained in crystalline form in only 7 h, with the synthesis temperature lowered by roughly 300 °C as compared to conventional methods.     

Synthesis and physicochemical properties of a solid oxide nanocomposite based on a ZrO<Subscript>2</Subscript>–Y<Subscript>2</Subscript>O<Subscript>3</Subscript>–Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–MgO system

A highly dispersive powder with a (ZrO₂)_0.92(Y₂O₃)_0.03(Gd₂O₃)_0.03(MgO)_0.02 composition and specific surface area of 150 m²/g has been synthesized via a method of coprecipitation of hydroxides with the subsequent cryochemical treatment of the gel. Nanoceramics based on the cubic modification of zirconium dioxide with the grain size of ~40–45 nm have been obtained. The temperature dependence of the specific electrical conductance of the nanoceramics within a temperature range of 350–870°C in air has been studied, and the ratio of the ionic and electronic parts of the conductance has been determined. Recommendations for the use of the obtained oxide nanocomposite as an electrolyte for a high-temperature fuel cell have been given.     

Magneto Optical Properties of FeB<Subscript>x</Subscript>Fe<Subscript>2−x</Subscript>O<Subscript>4</Subscript> Nanoparticles

In this study, FeB_xFe_2?xO₄ nanoparticles (NPs) were synthesized by the polyol method. The M–H hysteresis curves exhibit superparamagnetic characteristics that are both coercivity and remanent magnetization values are negligible. The particle size dependent Langevin function was applied to calculate the magnetic particle dimensions around 9 nm. The measured magnetic moments of NPs are in range of (1.52–2.2) µ_B and almost half or less with respect to 4 µ_B of bulk Fe ferrite. Magnetic anisotropy was specified as uniaxial and calculated effective anisotropy constants (K _eff ) are between 43.3 × 10⁴ and 19.4 × 10⁴ emu/g. The UV–Vis diffuse reflectance spectroscopy and Kubelka–Munk theory were used to determine the optical properties. The estimated optical band gap values (2.15–2.48 eV) of FeB_xFe_2?xO₄ NPs are bigger with respect to reported values (1.88–2.12 eV) for Fe₃O₄ NPs in the literature. The bigger E _g values are mainly attributed to B concentration and partly to quantum confinement effect.     

Synthesis and properties of binary spinels in a NiO–CuO–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The conditions for the formation of a spinel structure from a NiO–CuO–Fe₂O₃–Cr₂O₃ oxide mixture using several technological approaches have been examined. Addition of KCl is accompanied with the formation of two spinel-like phases, whereas in the absence of KCl just one solid solution of nickel–copper ferrite–chromite with the structure of a cubic spinel is formed. At the temperature of thermal treatment of 900°C, the presence of an admixture phase of the delafossite (CuCrO₂) type was established. The conditions for the fabrication of samples containing two spinel phases (cubic and tetragonal) characterized with the most developed surface and manifesting = increased catalytic activity in the reaction of the decomposition of an organic substance by hydrogen peroxide have been formulated. The studied features of spinel synthesis can be of interest for developing materials with an active surface promising for application as adsorbents of catalysts and sensors.     

Exploring the Redox Behavior of La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>Mn<Subscript>1−x</Subscript>Al<Subscript>x</Subscript>O<Subscript>3</Subscript> Perovskites for CO<Subscript>2</Subscript>-Splitting in Thermochemical Cycles

Mixed oxides with perovskite structure have been proposed as promising alternative for the solar fuel production via thermochemical redox cycles. For this work, the system La_0.6Sr_0.4Mn_1?xAl_xO₃ (x?=?0 to 0.8) was selected according to its high thermal stability and rapid oxidation kinetics, and the influence of the Al/Mn ratio on the redox properties was investigated. The characterization of the five oxides samples with different Al content confirmed the high redox capacity and the favorable behavior of these materials in consecutive cycles, as analyzed thermogravimetrically. The results show that following reduction at 1300?°C in inert atmosphere up to 0.32 mmol g^?1 of O₂ are released, while a 10-cycle reaction test confirms the feasibility of long term operation with these perovskites. It was observed that the reduction extent was enhanced with increasing the Al-content, but the oxidation degree is maximum for compositions near x?=?0.5, corresponding to an O₂ release of 0.318 mmol g^?1 (δ?=?0.132). After selecting the compositions with more promising redox properties, additional reactions were performed in a lab-scale fixed bed reactor with injection of CO₂ in the oxidation step at 900?°C in order to generate CO. In these tests, the most interesting results were obtained for the perovskite La_0.6Sr_0.4Mn_0.6Al_0.4O_3, with reduction extent of 0.266 mmol?g^?1, but the production of CO is in comparison significantly lower (0.114 mmol?g^?1). Further studies are required to determine the best operation conditions for thermochemical cycles using those materials.     

The Chemical Evolution of the La<Subscript>0.6</Subscript>Sr<Subscript>0.4</Subscript>CoO<Subscript>3−δ</Subscript> Surface Under SOFC Operating Conditions and Its Implications for Electrochemical Oxygen Exchange Activity

Owing to its extraordinary high activity for catalysing the oxygen exchange reaction, strontium doped LaCoO₃ (LSC) is one of the most promising materials for solid oxide fuel cell (SOFC) cathodes. However, under SOFC operating conditions this material suffers from performance degradation. This loss of electrochemical activity has been extensively studied in the past and an accumulation of strontium at the LSC surface has been shown to be responsible for most of the degradation effects. The present study sheds further light onto LSC surface changes also occurring under SOFC operating conditions. In-situ near ambient pressure X-ray photoelectron spectroscopy measurements were conducted at temperatures between 400 and 790 °C. Simultaneously, electrochemical impedance measurements were performed to characterise the catalytic activity of the LSC electrode surface for O₂ reduction. This combination allowed a correlation of the loss in electro-catalytic activity with the appearance of an additional La-containing Sr-oxide species at the LSC surface. This additional Sr-oxide species preferentially covers electrochemically active Co sites at the surface, and thus very effectively decreases the oxygen exchange performance of LSC. Formation of precipitates, in contrast, was found to play a less important role for the electrochemical degradation of LSC.     

Possible proton conduction in Ce<Subscript>0.9</Subscript>Gd<Subscript>0.1</Subscript>O<Subscript>2−δ</Subscript> nanoceramics

Dense samples of Ce_0.9Gd_0.1O_2−δ with grain sizes in the range 91–252 nm were prepared and their electrical properties studied by impedance spectroscopy. It was found that the bulk conductivity is not affected by grain size or atmosphere and that small grain sizes lead to a larger total resistance of the material. The most striking result corresponds to a sample sintered in wet air that exhibited electrical characteristics that hint clearly at the presence of proton conduction at temperatures below 200 °C.     

Study of Oxygen Reactivity in La<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Sr<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CoO<Subscript>3−δ</Subscript> Perovskites for Total Oxidation of Toluene

Abstract  

The total oxidation of toluene is studied over catalytic systems based on perovskite with general formula AA′CoO_3-δ (A = La, A′ = Sr). The systematic and progressive substitution of La³⁺ by Sr²⁺ cations in the series (La_1−x Sr _x CoO_3−δ system) of the perovskites have been studied to determine their influence in the final properties of these mixed oxides and their corresponding reactivity performance for the total oxidation of toluene as a model volatile organic compound with detrimental effects for health and environment. The structure and morphology of the samples before and after reaction have been characterized by XRD, BET and FE-SEM techniques. Additional experiments of temperature programmed desorption of O₂ in vacuum and reduction in H₂ were also performed to identify the main surface oxygen species and the reducibility of the different perovskites. It is remarkable that the La_1−x Sr _x CoO_3−δ series presents better catalytic performance for the oxidation of toluene, with lower values for the T₅₀ (temperature of 50 % toluene conversion) than the previously studied LaNi_1−y Co _y O₃ series.     

Comparative Study on Nano-Sized 1 wt% Pt/Ce<Subscript>0.8</Subscript>Zr<Subscript>0.2</Subscript>O<Subscript>2</Subscript> and 1 wt% Pt/Ce<Subscript>0.2</Subscript>Zr<Subscript>0.8</Subscript>O<Subscript>2</Subscript> Catalysts for a Single Stage Water Gas Shift Reaction

Abstract  

A comparative study on nano-sized Pt/Ce_0.8Zr_0.2O₂ and Pt/Ce_0.2Zr_0.8O₂ catalysts in a single stage water gas shift (WGS) reaction was carried out. These catalysts were prepared by impregnating 1 wt% Pt on nano-sized cubic (Ce_0.8Zr_0.2O₂) and tetragonal (Ce_0.2Zr_0.8O₂) supports. Both catalysts have been applied to WGS under identical conditions to understand beneficial effect of cubic/tetragonal phases of Ce_(1 − x)Zr_(x)O₂. 1 wt% Pt/Ce_0.8Zr_0.2O₂ exhibited higher CO conversion than 1 wt% Pt/Ce_0.2Zr_0.8O₂. In addition, 1 wt% Pt/Ce_0.8Zr_0.2O₂ catalyst showed relatively stable activity with time on stream. The high activity/stability of 1 wt% Pt/Ce_0.8Zr_0.2O₂ catalyst was correlated to its higher Pt dispersion and easier reducibility.     

Synthesis and research of nanopowders composed of 0.97ZrO<Subscript>2</Subscript> · 0.03La<Subscript>2</Subscript>O<Subscript>3</Subscript>

This work is devoted to the preparation of zirconium oxide nanopowders stabilized by lanthanum oxide using the method of codeposition in the presence of hydrogen peroxide. Nanopowders composed of 0.97ZrO₂ · 0.03La₂O₃ with particles of 10–20 nm are obtained. It is found that in the temperature interval of 500–1100°C the tetragonal and monoclinic points of the zirconium oxide phase crystallize at the same time.     

Synthesis of magnetically separable core–shell structured Ni<Subscript>x</Subscript>Fe<Subscript>1−x</Subscript>Fe<Subscript>2</Subscript>O<Subscript>4</Subscript>@TiO<Subscript>2</Subscript> nanoparticles photocatalysts for the degradation of organic dyes

In this paper, the core–shell structured NiFe₂O₄@TiO₂ nanoparticles and nanochains as photocatalysts were successfully prepared through hydrothermal and hydrolysis method. The as-prepared core–shell structure was composed of a magnetic NiFe₂O₄ core and photocatalytic titanium oxide coating shell. SEM and TEM images characterized the morphology of NiFe₂O₄@TiO₂ nanoparticles. Moreover, the results of XRD patterns proved that the TiO₂ coating shell consisted of anatase. The VSM measurements showed that the saturation magnetization values of NiFe₂O₄ and NiFe₂O₄@TiO₂ nanoparticles was 65 and 53 emu/g, respectively. The photocatalyst of NiFe₂O₄@TiO₂ nanoparticles exhibited the outstanding recyclable performance for RhB. And, the photo_degradation ration of maintained 69 % after the photocatalyst experienced ten photocatalysis experiments, which is better than that of Fe₃O₄@TiO₂ photocatalysts.     

Novel Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> aerogel/porous zirconia composite with ultra-low thermal conductivity

Highly porous zirconia fibers networks with a quasi-layered microstructure were successfully fabricated using vacuum squeeze moulding. The effects of inorganic binder content on the microstructure, room-temperature thermal and mechanical properties of fibrous porous zirconia ceramics were systematically investigated. Al₂O₃–SiO₂ aerogel was impregnated into fibrous porous ceramics, and the microstructures, thermal and mechanical properties of Al₂O₃–SiO₂ aerogel/porous zirconia composites were also studied. Results show that the Al₂O₃–SiO₂ aerogel/porous zirconia composites exhibited higher compressive strength (i.e., 1.22 MPa in the z direction) and lower thermal conductivity [i.e., 0.049 W/(m/K)]. This method provides an efficient way to prepare high-temperature thermal insulation materials.     

Structure and properties of solid solutions of La<Subscript>1 − <Emphasis Type="Italic">x</Emphasis></Subscript>Pr<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>BaCuFeO<Subscript>5 + δ</Subscript>

The effect of replacing lanthanum with praseodymium on the crystal chemistry parameters of solid solutions of La_{1 − x} Pr _x BaCuFeO_{5 + δ} has been investigated using X-ray powder diffraction analysis and IR spectroscopy. The thermal expansion, electroconductivity, and thermopower of these phases have been studied in air in the temperature range 300–1100 K. The values of linear thermal expansion coefficients (LTEC) of ceramics in different temperature ranges have been determined, and the values of electric transfer parameters in the above oxides have been calculated. It has been established that replacing lanthanum with praseodymium resulted in the compression of the elementary oxide unit La_{1 − x} Pr _x BaCuFeO_{5 + δ}, decrease in the content of labile oxygen in them (δ), decrease in nonmonotonic electroconductivity, increase in thermopower, decrease in LTEC, and difficulties in charge transfer in these phases.     

Fe-doping effects on the structural and electrochemical properties of 0.5Li<Subscript>2</Subscript>MnO<Subscript>3</Subscript>·0.5LiMn<Subscript>0.5</Subscript>Ni<Subscript>0.5</Subscript>O<Subscript>2</Subscript> electrode material

With the aim of achieving a high-performance 0.5Li₂MnO₃·0.5LiMn_0.5Ni_0.5O₂ material, a series of 0.5Li₂MnO₃·0.5LiMn _x Ni _y Fe_(1−x−y)O₂ (0.3 ≤ x ≤ 0.5, 0.4 ≤ y ≤ 0.5) samples with low Fe content was synthesized via coprecipitation of carbonates. Its crystal structure and electrochemical performance were characterized by means of powder X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy, galvanostatic charge/discharge testing, cyclic voltammetry, and electrochemical impedance spectra. Rietveld refinements with a model integrating R [`3] \overline{3} m and Fm [`3] \overline{3} m indicate that a low concentration of Fe incorporated in 0.5Li₂MnO₃·0.5LiMn_0.5Ni_0.5O₂ decrease a disordered cubic domain of the composite structure. The preferential distribution of Fe in cubic rock-salt contributes to an unimaginable decrease of c-axis parameter of the predominant layered structure as the Fe content increases. Moreover, including Fe as a dopant can kinetically improve crystallization and also change the ratio of Mn³⁺/Mn⁴⁺ and Ni³⁺/Ni²⁺. As a result, 0.5Li₂MnO₃·0.5LiMn_0.4Ni_0.5Fe_0.1O₂ exhibits lower Warburg impedance and higher reversible capacity than the undoped material.     

Influence of Calcination Temperature on Activity and Selectivity of Ni–CeO<Subscript>2</Subscript> and Ni–Ce<Subscript>0.8</Subscript>Zr<Subscript>0.2</Subscript>O<Subscript>2</Subscript> Catalysts for CO<Subscript>2</Subscript> Methanation

Herein, we studied the influence of calcination temperature (500–800 °C) of Ni/CeO₂ and Ni/Ce_0.8Zr_0.2O₂ catalysts on the specific surface area, pore volume, crystalline size, lattice parameter, chemical bonding and oxidation states, nickel dispersion and CH₄/CO production rate in CO₂ methanation. In general, the catalytic performance revealed that Zr doping catalysts could increase the CH₄ production rate. Combined with the production rate and the characterizations results, we found that the combination of nickel dispersion, peak area of CO₂–TPD and O_II/(O_II + O_I)) play the critical role in increasing the CH₄ production rate. It is well to be mentioned that the CO production rate is strongly influenced by the nickel dispersion. Furthermore, the in-situ DRIFTS confirmed that the CO originates from the decomposition of H-assisted formate species.     

Spatial localization of holes in La<Subscript>2 − <Emphasis Type="Italic">x</Emphasis></Subscript>Sr<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CuO<Subscript>4</Subscript>

The parameters of the tensor of the electric field gradient (EFG) in cation sites of the La_{2 ? x} Sr _x CuO₄ lattice have been determined by the method of emission Mössbauer spectroscopy on ⁵⁷Co(^57m Fe), ⁶⁷Cu(⁶⁷Zn), ⁶⁷Ga(⁶⁷Zn), and ¹⁵⁵Eu(¹⁵⁵Gd) isotopes. There is no quantitative agreement between the calculated (the pointcharge model) and experimental values of the main component of the tensor EFG V _zz , which is explained by the absence of the reliable data on the Sternheimer coefficients for Fe³⁺, Zn²⁺, and Gd³⁺ ions. Based on the comparison of the calculated and experimental dependences of V _zz on x it was shown that the holes appearing during the substitution of La³⁺ for Sr²⁺ are localized preferably on the oxygen atoms that are in the same plane as the copper atoms, which is in agreement with the model discussed in the literature and assumes that the mechanism responsible for the high-temperature superconductivity of solid solutions La_{2 ? x} Sr _x CuO₄ is the interaction between the conductivity electrons and two-atomic two-electron centers with negative correlation energy.     

Change of the thermal behavior of 55Bi<Subscript>2</Subscript>O<Subscript>3</Subscript> ⋅ 45B<Subscript>2</Subscript>O<Subscript>3</Subscript> glass at annealing close to the vitrification temperature

The characteristic properties of relaxation processes for 55Bi₂O₃ ? 45B₂O₃ glass were described. The pattern of changes of the vitrification temperature (T _g ) is found to be quasi-periodic; the value of the endothermic effect near T _g (ΔC’ _p ) and the difference between the softening point and the vitrification temperature (T _m –T _g ) were determined. The temperature-time parameters of the transition from quasi-periodic to the continuous change of the properties were determined and an explanation of such behavior of the system was offered.