Foaming of rigid PVC/wood‐flour composites through a continuous extrusion process

The effects of chemical foaming agent (CFA) types (endothermic versus exothermic) and concentrations as well as the influence of all‐acrylic processing aid on the density and cell morphology of extrusion‐foamed neat rigid PVC and rigid PVC/wood‐flour composites were studied. Regardless of the CFA type, the density reduction of foamed rigid PVC/wood‐flour composites was not influenced by the CFA content. The cell size, however, was affected by the CFA type, independent of CFA content. Exothermic foaming agent produced foamed samples with smaller average cell sizes compared to those of endothermic counterparts. The experimental results indicate that the addition of an all‐acrylic processing aid in the formulation of rigid PVC/wood‐flour composite foams provides not only the ability to achieve density comparable to that achieved in the neat rigid PVC foams, but also the potential of producing rigid PVC/wood‐flour composite foams without using any chemical foaming agents.     

Manufacture of rigid PVC/wood‐flour composite foams using moisture contained in wood as foaming agent

Relatioships between the density of foamed rigid PVC/wood‐flour composites and the moisture content of the wood flour, the chemical foaming agent (CFA) content, the content of all‐acrylic foam modifier, and the extruder die temperature were determined by using a response surface model based on a four‐factor central composite design. The experimental results indicated that there is no synergistic effect between teh CFA content and the moisture content of the wood flour. Wood flour moisture could be used effectively as foaming agent in the production of rigid PVC/wood‐flour composite foams. Foam density as low as 0.4 g/cm³ was produced without the use of chemical foaming agents. However, successful foaming of rigid PVC/wood‐flour composite with moisture contained in wood flour strongly depends upon the presence of all‐acrylic foam modifier in the formulation and the extrusion die temperature. The lowest densities were achieved when the all‐acrylic foam modifier concentration was between 7 phr and 10 phr and extruder die temperature was as low as 170°C.     

Critical processing temperature in the manufacture of fine‐celled plastic/wood‐fiber composite foams

The main benefits of incorporating wood fibers (WF) in plastics are the increased stiffness and lowered cost of the resulting composites. However, these improvements are usually accompanied by a reduction in the ductility and impact resistance. These shortcomings can be removed by effectively foaming and incorporating a fine‐celled structure in these composites. The volatiles released from WF during processing are known to deteriorate the cell structure. The maximum processing temperature, which affects the amount of volatiles released by the WF during extrusion of fine‐celled plastic/WF composite, affects the cell morphology. This study was undertaken to identify the critical temperature above which the cellular structure of WF composite foams is significantly deteriorated. To clearly identify the effects of the volatiles generated from WF on the cellular morphology, neither a chemical blowing agent nor a physical blowing agent was used in the foam processing. The experimental results show that regardless of the drying method, the highest processing temperature of plastic/WF composites should be minimized, preferably below 170°C, to avoid the adverse effects of the volatiles generated from the WF during processing. A method of estimating the emissions from WF during extrusion processing by using the TGA data is also proposed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 621–629, 2004     

Effects of the chemical foaming agents,injection parameters,and melt‐flow index on the microstructure and mechanical properties of microcellular injection‐molded wood‐fiber/polypropylene composites

Wood‐fiber‐reinforced plastic profiles are growing rapidly in nonstructural wood‐replacement applications. Most manufacturers are evaluating new alternative foamed composites, which are lighter and more like wood. Foamed wood composites accept screws and nails better than their nonfoamed counterparts, and they have other advantages as well. For example, internal pressures created by foaming give better surface definition and sharper contours and corners than nonfoamed profiles have. In this study, the microfoaming of polypropylene (PP) containing hardwood fiber was performed with an injection‐molding process. The effects of different chemical foaming agents (endothermic, exothermic, and endothermic/exothermic), injection parameters (the mold temperature, front flow speed, and filling quantity), and different types of PP (different melt‐flow indices) on the density, microvoid content, physicomechanical properties, surface roughness, and microcell classification of microfoamed PP/wood‐fiber composites were studied. A maleic anhydride/polypropylene copolymer (MAH‐PP) compatibilizer was used with the intention of improving the mechanical properties of microfoamed composites. The microcell classification (from light microscopy) and scanning electron micrographs showed that an exothermic chemical foaming agent produced the best performance with respect to the cell size, diameter, and distance. The polymer melt‐flow index and the variation of the injection parameters affected the properties and microstructure of the microfoamed composites. The density of the microfoamed hardwood‐fiber/PP (with a high melt‐flow index) composites was reduced by approximately 30% and decreased to 0.718 g/cm³ with an exothermic chemical foaming agent. Tensile and flexural tests were performed on the foamed composites to determine the dependence of the mechanical properties on the density and microvoid content of the foamed specimens, and these properties were compared with those of nonfoamed composites. MAH‐PP improved the physicomechanical properties up to 80%. With an increase in the mold temperature (80–110°C), the surface roughness was reduced by nearly 70% for the foamed composites. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1090–1096, 2005     

Foam extrusion of high density polyethylene/wood‐flour composites using chemical foaming agents

A one‐way analysis of variance and thermal analysis were performed in this study to examine the influences of the contents, types (exothermic vs. endothermic), and forms (pure vs. masterbatch) of chemical foaming agents (CFAs), as well as the use of coupling agents, on the density reduction (or void fraction) and cell morphology of extrusion‐foamed neat high density polyethylene (HDPE) and HDPE/wood‐flour composites. The CFA types and forms did not affect the void fractions of both the neat HDPE and HDPE/wood‐flour composites. However, a gas containment limit was observed for neat HDPE foams whereas the average cell size achieved in the HDPE/wood‐flour composite foams remained insensitive to the CFA contents, irrespective of the foaming agent types. The experimental results indicated that the use of coupling agent in the formulation was required to achieve HDPE/wood‐flour composite foams with high void fraction. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3139–3150, 2003     

Mechanical properties of extrusion‐foamed rigid PVC/wood‐flour composites

This study was conducted to characterize the mechanical properties of extrusion‐foamed neat rigid PVC and rigid PVC/wood‐flour composites by using endothermic and exothermic chemical foaming agents (CFAs). The specific elongation at break (ductility) of the samples was improved by foaming, while the opposite trend was observed for the tensile strength and modulus of the samples, regardless of the chemical foaming agent type. In addition, experimental results indicated that foaming reduced the Izod impact resistance of both neat rigid PVC and rigid PVC/wood‐flour composites but that this reduction was not statistically significant for the composites. A comparison between batch microcellular processing and extrusion foam processing was made, which demonstrated that foams with very fine cells (microcellular processed) exhibit better impact strength than foams with larger cells (extrusion processed with CFAs).     

Effects of material parameters on the diffusion and sorption properties of wood‐flour/polypropylene composites

Composites of wood in a thermoplastic matrix (wood–plastic composites) are considered a low maintenance solution to using wood in outdoor applications. Knowledge of moisture uptake and transport properties would be useful in estimating moisture‐related effects such as fungal attack and loss of mechanical strength. Our objectives were to determine how material parameters and their interactions affect the moisture uptake and transport properties of injection‐molded composites of wood‐flour and polypropylene and to compare two different methods of measuring moisture uptake and transport. A two‐level, full‐factorial design was used to investigate the effects and interactions of wood‐flour content, wood‐flour particle size, coupling agent, and surface removal on moisture uptake and transport of the composites. Sorption and diffusion experiments were performed at 20°C and 65 or 85% relative humidity as well as in water, and diffusion coefficients were determined. The wood‐flour content had the largest influence of all parameters on moisture uptake and transport properties. Many significant interactions between the variables were also found. The interaction between wood‐flour content and surface treatment was often the largest. The diffusion coefficients derived from the diffusion experiments were different from those derived from the sorption experiments, suggesting that different mechanisms occur. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 752–763, 2007     

Foaming of PS/wood fiber composites using moisture as a blowing agent

This paper presents an experimental study on foam processing of polystyrene (PS) and high‐impact polystyrene HIPS/wood‐fiber composites in extrusion using moisture as a blowing agent. Wood‐fiber inherently contains moisture that can potentially be used as a blowing agent. Undried wood‐fiber was processed together with PS and HIPS materials in extrusion and wood‐fiber composite foams were produced. The cellular morphology and volume expansion ratios of the foamed composites were characterized. Because of the high stiffness of styrenic materials, moisture condensation during cooling after expansion at high temperature did not cause much contraction of the foamed composite and a high volume expansion ratio up to 20 was successfully obtained. The experimental results showed that the expansion ratio could be controlled by varying the processing temperature and the moisture content in the wood fiber. The effects of a small amount of a chemical blowing agent and mineral oil on the cell morphologies of plastic/wood‐fiber composite foams were also investigated.     

Experimental investigation on mechanical properties of extruded foamed PVC‐wood composites reinforced with continuous glass fibers

In this study, mechanical performances of extruded foamed and unfoamed PVC‐wood composites, reinforced with continuous glass fibers, were investigated. A specially designed die was used to incorporate the continuous glass rovings into the extruded rectangular shaped profiles. The experimental variables were the number of continuous glass rovings (0–2‐4) and the presence or absence of the chemical foaming agent. Three point bending tests as well as density measurements were conducted to evaluate the mechanical properties and density reduction upon foaming. The results showed that the flexural strength of the reinforced profiles was significantly increased, as 58% increase in flexural strength was noticed for wood plastic composites (WPCs) reinforced with four glass rovings. The highest density reduction (14%) was observed upon foaming for profiles reinforced with four glass rovings, while resulting in strength deterioration. Moreover, results revealed the remarkable effect of reinforcement on preserving mechanical performance of the foamed samples, as 88% increase in flexural strength of the foamed samples reinforced with four glass rovings was observed compared with the unreinforced foamed ones. For the foamed WPCs reinforced with even two glass rovings, the higher specific strength values were also noticed compared to the unreinforced and unfoamed samples. POLYM. COMPOS., 37:1674–1680, 2016. © 2014 Society of Plastics Engineers     

Effect of compatibilizers on water absorption kinetics of polypropylene/wood flour foamed composites

Polypropylene (PP)/wood flour foamed composites were prepared by taking PP:wood flour in the ratios of 100 : 0, 90 : 10, 80 : 20, 70 : 30, and 60 : 40 (w/w), with and without compatibilizers like maleic anhydride‐treated wood flour and maleic anhydride‐grafted PP (PPgMA). The foamed composite samples were employed for water swelling at 27°C, 70°C, and in steam. The absorption of water increased with increase in filler contents for all three‐temperature conditions. The maleic anhydride‐treated wood flour and PPgMA showed reduction in water swelling, and the best one was in case of the PPgMA‐foamed composites for respective conditions. Diffusion, sorption, and permeation coefficients were determined to study the absorption kinetics. FTIR spectra were also recorded for 30 wt % of filler loading for all the composites, which showed the effect of compatibilizers on reduction in water absorption in foamed PP/wood flour composites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2530–2537, 2006     

木粉和发泡剂对PVC基木塑复合发泡材料性能的影响

以木粉、聚氯乙烯树脂、发泡剂等为原料,通过连续挤出得到发泡木塑复合材料。对木粉的热失重、复合发泡材料的泡孔形态、力学性能进行了测试。结果表明:发泡剂用量不应超过1phr;在本实验范围内,木粉粒径的减小会使发泡更容易,材料的力学性能得到改善;木粉粒径对泡孔形态和力学性能的影响有一个最佳范围,即20~80目。     

Studies on the Thermal and Mechanical Properties of Foamed Wood-Polymer Composites

Wood flour-polypropylene foamed composites, in ratios of 10:90, 20:80, 30:70, and 40:60 (wt./wt.), were prepared with and without maleic anhydride treatment of wood flour and maleic anhydride-grafted PP (MAgPP). The effects of the amount of wood flour and its treatment on the morphology, the mechanical properties, and the thermal properties of the composites were investigated. Vicat softening temperatures (VST) were recorded as 112.9°C, 103.2°C, and 96.2°C for MAgPP wood flour (MPP), maleic anhydride-treated wood flour (MWF), and untreated wood flour (UWF) (40:60 wt./wt.) foamed composites, respectively. The heat distortion temperatures (HDT) were measured to be 80°C, 76°C, and 58°C for the respective composites. DSC thermograms showed an increase in the crystallinity of MPP and MWF composites with an increase in the ratio of wood flour in the composite, whereas the opposite trend was observed in untreated wood flour. Except for impact strength and flexural strength, Young's modulus, flexural modulus, and hardness all increased with an increase in wood flour content. The micrographs confirmed the foaming. The improvement in the properties of the composites is due to the increment in interfacial bonding between polymer and wood flour, which is caused by the compatibilizers.     

Coextruded PVC/wood‐flour composites with WPC cap layers

Wood‐plastic composites (WPCs) can absorb moisture in a humid environment owing to the hydrophilic nature of the wood, thereby making the products susceptible to microbial growth and loss of mechanical properties. In this study, rigid poly(vinyl chloride) (PVC)/wood‐flour composites (core layer) were coextruded with either unfilled rigid PVC (cap layer) or rigid PVC filled with a small amount (5–27.5%) of wood flour (composite cap layers) in order to decrease or delay the moisture uptake. The thickness of the cap layer and its composition in terms of wood flour content were the variables examined during coextrusion. Surface color, moisture absorption, and flexural properties of both coextruded and noncoextruded (control) composite samples were characterized. The experimental results indicated that both unfilled PVC and composite cap layers can be encapsulated over rigid PVC/wood‐flour composites in a coextrusion process. The moisture uptake rate was lower when a cap layer was applied in the composites, and the extent of the decrease was a strong function of the amount of wood flour in the cap layer but insensitive to cap layer thickness. Overall, coextruding PVC surface‐rich cap layers on WPCs significantly increased the flexural strength but decreased the flexural modulus as compared with those of control samples. The changes in bending properties were sensitive to both cap layer thickness and wood flour content. J. VINYL ADDIT. TECHNOL., 2008. © 2008 Society of Plastics Engineers     

Microcellular Foamed Wood‐Plastic Composites by Different Processes: a Review

Wood fiber reinforced polymer composites represent a relatively small but rapidly growing material class, extensively applied in interior building applications and in the automotive industry. The polymer‐wood fiber composites utilize fibers as reinforcing filler in the polymer matrix and are known to be advantageous over the neat polymers in terms of the materials cost and mechanical properties such as stiffness and strength. Wood fiber reinforced polymer composites are microcellularly processed to create a new class of materials with unique properties. Most manufacturers are evaluating new alternatives of foamed composites that are lighter and more like wood. Foamed wood composites accept screws and nails like wood, more so than their non‐foamed counterparts. They have other advantages such as better surface definition and sharper contours and corners than non‐foamed profiles, which are created by the internal pressure of foaming. This paper represents a review on microcellular wood fiber reinforced polymer composites obtained by different processes (batch, injection molding, extrusion, and compression molding process) and includes an overview of foaming agents (physical and chemical) and the foaming of wood fiber‐polymer composites (changes in phase morphology, formation of polymer‐gas solution, cell nucleation, and cell growth control).

     

Wood/plastic composites co‐extruded with multi‐walled carbon nanotube‐filled rigid poly(vinyl chloride) cap layer

Wood/plastic composites (WPCs) can absorb moisture in a humid environment due to the hydrophilic nature of the wood in the composites, making products susceptible to microbial growth and loss of mechanical properties. Co‐extruding a poly(vinyl chloride) (PVC)‐rich cap layer on a WPC significantly reduces the moisture uptake rate, increases the flexural strength but, most importantly, decreases the flexural modulus compared to uncapped WPCs. A two‐level factorial design was used to develop regression models evaluating the statistical effects of material compositions and a processing condition on the flexural properties of co‐extruded rigid PVC/wood flour composites with the ultimate goal of producing co‐extruded composites with better flexural properties than uncapped WPCs. Material composition variables included wood flour content in the core layer and carbon nanotube (CNT) content in the cap layer of the co‐extruded composites, with the processing temperature profile for the core layer as the only processing condition variable. Fusion tests were carried out to understand the effects of the material compositions and processing condition on the flexural properties. Regression models indicated all main effects and two powerful interaction effects (processing temperature/wood flour content and wood flour content/CNT content interactions) as statistically significant. Factors leading to a fast fusion of the PVC/wood flour composites in the core layer, i.e. low wood flour content and high processing temperature, were effective material composition and processing condition parameters for improving the flexural properties of co‐extruded composites. Reinforcing the cap layer with CNTs also produced a significant improvement in the flexural properties of the co‐extruded composites, insensitive to the core layer composition and the processing temperature condition. Copyright © 2009 Society of Chemical Industry     

Effects of chemical modification of wood flour on the rheological properties of high‐density polyethylene blends

Chemical modification of lignocellulosic fibers can improve interfacial adhesion and dimensionally stabilize the resulting plastic composites. This study examined the rheological properties of wood flour/high density polyethylene (HDPE) melts after poplar wood flour was modified with glutaraldehyde (GA, mainly cell wall cross‐linking) and 1,3‐dimethylol‐4,5‐dihydroxyethyleneurea (DMDHEU, mainly poly‐condensation). Results show improvement in both the dispersibility of treated wood flour in the HDPE and its interfacial compatibility. Treatment with GA decreased melt viscosity, moduli, and shear stress as evidenced by rheometry. However, the modifying effects of DMDHEU were not observed, which was mainly due to reduced HDPE content. This study indicates that chemical modification of wood flour is a promising approach to improve the processability of highly filled wood thermoplastic composites via extrusion/injection molding processing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41200.     

表面处理对木粉增强PVC发泡复合板材性能的影响

研究表面处理的木粉对发泡聚氯乙烯(PVC)板材的增强改性效果。使用铝酸酯偶联剂、丙烯酸丁酯预聚物对木粉进行表面处理，将其混合到聚氯乙烯发泡板材配料中进行板材加工生产，结果表明，经处理的木粉能提高发泡PVC板材的拉伸强度和冲击强度。用铝酸酯偶联剂处理木粉的发泡板材力学性能好于用丙烯酸丁酯预聚物处理的板材；而用丙烯酸丁酯预聚物处理木粉的复合材料在流变加工性能优于用铝酸酯处理木粉的复合材料。     

Density reduction behaviors and cell morphology in extrusion of LLDPE/wood fiber composites with physical and chemical blowing agents

Foamed wood fiber/plastic composites (WPC) with a fine-cell structure offer many benefits compared with the unfoamed WPC, such as the reduced material cost and density, the improved toughness, and the enhanced processability. However, it is extremely challenging to achieve the desired density reduction and obtain a fine-cell structure simultaneously. One of the obstacles is that the volatiles released from the wood fiber (WF) during processing should be suppressed to ensure a fine-cell structure. Linear low-density polyethylene (LLDPE) has a relatively low melting temperature, and it can reduce the processing temperature and suppress volatiles when used as a polymer matrix for foamed WPC. This paper systematically investigates the foamability of LLDPE/WF composites in a continuous foam extrusion, with both a chemical blowing agent and a physical blowing agent (PBA). It turns out that the PBA-based foaming led to a smaller cell size and a narrower cell size distribution. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48829.     

Investigation on microstructure and properties of foamed (wood fiber)/(recycled polypropylene) composites

Microcellular foamed (wood fiber)‐reinforced recycled polypropylene composites (MFWPCs) were prepared by an injection molding process where azodicarbonamide was used as a chemical foaming agent. The influence of injection parameters (injection temperature, dwell pressure) on the microcellular structure (cell diameter and cell density) and the mechanical properties of the MFWPCs were investigated. The results indicated that when the melting temperature was 180°C and the dwell pressure was 12.5 MPa, a uniformly distributed microcellular structure of MFWPCs was obtained. Compared with solid wood plastic composites, the density of the MFWPCs decreased by 24.5%, and its impact strength of MFWPCs increased by 53%, because the propagation direction of the crack changed to the “skip” or “bifurcation” mechanism as a result of the microcellular structure, and the surrounding matrix of this structure made it easy to produce forced high‐elastic deformation. The toughening mechanism of the microcellular structure was analyzed. J. VINYL ADDIT. TECHNOL., 2012. © 2012 Society of Plastics Engineers     

Potassium methyl siliconate‐treated pulp fibers and their effects on wood plastic composites: Water sorption and dimensional stability

Potassium methyl siliconate (PMS) was investigated as a new nano modifier of wood fiber and wood flour to improve the compatibility between the fiber/flour and the plastic matrix in fiber reinforced plastic composites. Before injection molding, bleached and brown pulp fibers and mixed species wood flour were pretreated in PMS solutions. The morphology of the treated and untreated fiber and flour, the compatibility of PMS‐treated fiber and flour with polyethylene (PE), and the water sorption and volumetric swell of PMS‐treated fiber/flour plastic composites in a long‐term soaking test were evaluated. Fiber and flour treated with PMS increased the compatibility between the fiber/flour and the PE matrix. The increased compatibility of PMS‐treated fiber and flour with the matrix contributed to the reduction of water sorption and, thus, increased dimensional stability. For all composites, water sorption and volumetric swell of fiber/four plastic composites decreased as the ratio of fiber to flour increased. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013