改善模塑料性能的苯酚改性蜜胺树脂的制备

采用苯酚对三聚氰胺-甲醛树脂(MF)进行改性,研究了3种原料(苯酚、三聚氰胺和甲醛)不同配比下的合成产物的模塑料性能,优选出低酚摩尔分数(8%)的用于模塑料加工的苯酚改性蜜胺树脂(PMF)。该树脂中甲醛与三聚氰胺的物质的量比(F1/M)为1.75∶1,甲醛与苯酚的物质的量比(F2/P)为1.7∶1,甲醛和苯酚的物质的量之和与三聚氰胺物质的量比((F1+F2+P)/M)为2.5∶1。该树脂可提高模塑料的加工性能,降低加工能量损耗,改善制品的模塑性和耐冲击性。     

Resorcinol in high solid phenol−formaldehyde resins for foams production

The acid curing agent content and foaming temperature could be reduced by improving the resol reactivity. In this study, highly active and solid phenol?resorcinol?formaldehyde copolymer resins (PRFRs) with different resorcinol/phenol (R /P ) molar ratios and formaldehyde/(phenol + resorcinol) [F /(P + R )] molar ratios were synthesized through the copolymerization of resorcinol, formaldehyde, and phenol. Phenol?resorcinol?formaldehyde foams (PRFFs) were prepared with synthetic PRFRs. The results showed that PRFR‐2 exhibited higher reactivity, faster curing speed, and better thermal stability. In addition, the foam produced with the PRFR‐2 had improved mechanical and flame retardation properties and a compressive strength of 0.18 MPa, a flexural strength of 0.25 MPa, and a limited oxygen index (LOI) greater than 37%. The increased reactivity of the PRFRs correlated with the changing mechanical properties of PRFFs because of the effects of resorcinol and the molar ratio of formaldehyde to phenol and resorcinol. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44881.     

Time–temperature–transformation cure diagrams of phenol–formaldehyde and lignin–phenol–formaldehyde novolac resins

In this study, the time–temperature– transformation (TTT) cure diagrams of the curing processes of several novolac resins were determined. Each diagram corresponded to a mixture of commercial phenol–formaldehyde novolac, lignin–phenol–formaldehyde novolac, and methylolated lignin–phenol–formaldehyde novolac resins with hexamethylenetetramine as a curing agent. Thermomechanical analysis and differential scanning calorimetry techniques were applied to study the resin gelation and the kinetics of the curing process to obtain the isoconversional curves. The temperature at which the material gelled and vitrified [the glass‐transition temperature at the gel point (_gelT_g)], the glass‐transition temperature of the uncured material (without crosslinking; T_g0), and the glass‐transition temperature with full crosslinking were also obtained. On the basis of the measured of conversion degree at gelation, the approximate glass‐transition temperature/conversion relationship, and the thermokinetic results of the curing process of the resins, TTT cure diagrams of the novolac samples were constructed. The TTT diagrams showed that the lignin–novolac and methylolated lignin–novolac resins presented lower T_g0 and _gelT_g values than the commercial resin. The TTT diagram is a suitable tool for understanding novolac resin behavior during the isothermal curing process. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and properties of composites based on melamine‐formaldehyde foam and nano‐Fe3O4

In this work, a novel melamine‐formaldehyde‐Fe₃O₄ foam was prepared from a mixture containing melamine‐ethanolamine‐formaldehyde resin, melamine‐glycol‐formaldehyde resin and carboxylated Fe₃O₄ nanoparticles by microwave foaming method. The two resins were characterized by ¹³C‐NMR, respectively. The structures of foams, mechanical and fire‐retardant properties were experimentally characterized separately by scanning electron microscopy, universal testing machine, limit oxygen index, thermogravimetry‐differential thermal analysis, and Fourier transform infrared spectra. The effects of the resin viscosity, emulsifier, nucleating agent, curing agent, silicone oil, microwave heating time and blowing agent on the structure of foam were investigated. Results showed that the properties of foam were decided by not only the molecular structure but also structure of foam, and the carboxylated Fe₃O₄ nanoparticles can improve the toughness and flame retardant properties of magnetic foam obviously from both aspects. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2688–2697, 2013     

Multifunctional formaldehyde resins as curing agent for epoxy resins

Formaldehyde resins (FR) at 1/1/2 molar ratios of monomers (Cl‐phenol/amino monomers/p‐formaldehyde) were synthesized under acid catalysis. The obtained resins were characterized using elemental analysis, FTIR and RMN spectroscopic methods, being used as crosslinking agents for epoxy resin formulations. The curing of epoxy resins with FR were investigated. The glass transition temperature (T_g) and decomposition behavior of crosslinked resins were studied by differential scanning calorimetry (DSC) and thermogravimetric (TGA) techniques. All DSC scans show two exothermic peaks, which implied the occurrence of cure reactions between epoxy ring and amine or carboxylic protons, in function of chemical structures of FR. The crosslinked products showed good thermal properties, high glass transitions, and low water absorption. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effects of formaldehyde to urea mole ratio on thermal curing behavior of urea–formaldehyde resin and properties of particleboard

As a part of abating the formaldehyde emission (FE) of urea–formaldehyde (UF) resin, this study was conducted to investigate the effects of formaldehyde to urea (F/U) mole ratio on thermal curing behavior of UF resins and properties of PB bonded with them. UF resins synthesized at different F/U mole ratios (i.e., 1.6, 1.4, 1.2, and 1.0) were used for the manufacture of PB. Thermal curing behavior of these UF resins was characterized using differential scanning calorimetry (DSC). As the F/U mole ratio decreases, the gel time, onset and peak temperatures, and heat of reaction (ΔH) increased, while the activation energy (E_a) and rate constant (k) were decreased. The amount of free formaldehyde of UF resin and FE of PB prepared decreased in parallel with decreasing the F/U mole ratio. The internal bond strength, thickness swelling, and water absorption of PB was slightly deteriorated with decreasing the F/U mole ratio of UF resins used. These results indicated that as the F/U mole ratio decreased, the FE of PB was greatly reduced at the expense of the reactivity of UF resin and slight deterioration of performance of PB prepared. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1787–1792, 2006     

Influence of the synthesis conditions on the curing behavior of phenol–urea–formaldehyde resol resins

The curing behavior of synthesized phenol–urea–formaldehyde (PUF) resol resins with various formaldehyde/urea/phenol ratios was studied with differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). The results indicated that the synthesis parameters, including the urea content, formaldehyde/phenol ratio, and pH value, had a combined effect on the curing behavior. The pH value played an important role in affecting the shape of the DSC curing curves, the activation energy, and the reaction rate constant. Depending on the pH value, one or two peaks could appear in the DSC curve. The activation energy was lower when pH was below 11. The reaction rate constant increased with an increase in the pH value at both low and high temperatures. The urea content and formaldehyde/phenol ratio had no significant influence on the activation energy and rate constant. DMA showed that both the gel point and tan δ peak temperature (T_tanδ) had the lowest values in the mid‐pH range for the PUF resins. A different trend was observed for the phenol–formaldehyde resin without the urea component. Instead, the gel point and T_tanδ decreased monotonically with an increase in the pH value. For the PUF resins, a high urea content or a low formaldehyde/phenol ratio resulted in a high gel point. The effect of the urea content on T_tanδ was bigger than that on the gel point because of the reversible reaction associated with the urea component. Too much formaldehyde could lead to more reversible reactions and a higher T_tanδ value. The effects of the synthesis conditions on the rigidity of the cured network were complex for the PUF resins. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1368–1375, 2005     

密胺树脂硫磺微胶囊的制备及应用

针对橡胶硫化中的"喷霜"和橡胶裂纹的自修复问题,以升华硫为芯材,密胺树脂(PMF)为壳材,采用原位聚合法制备了密胺树脂硫磺微胶囊.研究了密胺树脂的缩聚pH值对微胶囊形态的影响,乳化剂浓度、芯材含量对微胶囊粒径的影响以及密胺树脂的缩聚pH值、液固相比(w/s)、甲醛和密胺的摩尔比对微胶囊包覆率的影响.结果表明:密胺树脂的...     

Mechanical,thermal, and water absorption properties of melamine–formaldehyde‐treated sisal fiber containing poly(lactic acid) composites

The present study focuses on the melamine–formaldehyde (MF) coating ratio and silanization of PLA/sisal composites. Poly(lactic acid) (PLA) was melt blended with short sisal fiber with and without MF resin coating. MF was applied at different weight ratios (sisal:MF = 1:1; 1:3, and 1:5) to coat the untreated or silanized sisal fibers which were incorporated up to 20 parts per hundred resin (phr) amount in PLA. PLA/sisal composites were produced by compression molding. It was found that the sisal:MF coating ratio at 1:1 by weight improved the tensile strength and tensile modulus of the composite with 10 phr sisal by 4% and 57%, respectively, compared to the virgin PLA. The initial and final decomposition (T_i) and (T_f) of PLA with untreated sisal were changed from 330.8 and 367.1 to 336.2 and 370.4 °C, respectively, after MF‐coating (sisal:MF weight ratio = 1:1). This enhancement in thermal stability was attributed to the strong interaction between the MF and sisal fiber. The water absorption of PLA/MF–sisal composites slightly decreased with increasing sisal:MF ratio. This is due to the fact that the MF‐coating substantially reduced the hydrophilic properties of sisal. Moreover, FTIR spectra and SEM images proved that sisal fibers were coated by MF resin successfully. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45681.     

A 13C-NMR analysis method for MUF and MF resin strength and formaldehyde emission

A method based on the use of ¹³C-NMR relative peak intensity ratios for chemical groups known to contribute to melamine-urea-formaldehyde (MUF) and melamine-formaldehyde (MF) resin strength and formaldehyde emission is presented. The method relates results obtained by ¹³C-NMR analysis of liquid MUF and MF resins with their strength and formaldehyde emission in the hardened state. Correlation of different peak ratios with experimental results showed that, contrary to other formaldehyde-based resins, the NMR analysis for the MUF and MF resins needs only to take into account the triazine/substituted triazines and the urea/substituted ureas peak ratios to allow the proposal of equations correlating a single spectrum of the liquid resin with the physical properties of the boards bound with the same resin in its hardened state. Correlation equations are developed for both the case in which variation of the amine: formaldehyde molar ratio is directly induced at the resin preparation stage as well as the case in which it is induced at the glue-mixing stage, the latter by addition of different types of resin accelerators and resin scavengers. © 1996 John Wiley & Sons, Inc.     

低醛三聚氰胺树脂的制备与工艺研究

以三聚氰胺(M)、甲醛(F)和乙二醇(EG)为主要原料,三乙醇胺为催化剂,己内酰胺、H2O2为甲醛吸收剂,采用低n(F)∶n(M)比例、乙二醇醚化MF(三聚氰胺-甲醛)树脂、三聚氰胺分次加料和添加甲醛吸收剂等手段,制备MF树脂。研究结果表明:当n(F)∶n(M)=2.5∶1、n(EG)∶n(M)=2.0∶1、pH值为8～9、反应温度为80℃、三聚氰胺分次加料量为50∶40∶10(质量比)和n(己内酰胺)∶n(H2O2)∶n(甲醛)=10∶5∶100时,制成的MF树脂具有相对较低的游离甲醛含量(0.13%)和相对较长的储存稳定期(>120 d)。     

Carbon fiber cardanol-epoxy composites

Carbon fiber composites based on tetrafunctional epoxy resin N,N,N′,N′-tetraglycidyl-2,2-bis[4-(4-aminophenoxy)phenyl]propane modified with cardanol were investigated. The differential scanning calorimetric technique was used to study the curing reaction of the neat resins. The dielectric properties of the composites were compared. The use of cardanol in epoxy resins at cardanol/epoxy molar ratios less than 0.3/1 improved the chemical resistance as well as the mechanical properties of the composites, such as the flexural strength and modulus, tensile strength and modulus, and interlaminar shear strength. Higher cardanol contents decreased such properties. The highest properties of the composites were observed with the epoxy-cardanol resin having a cardanol/epoxy molar ratio of 0.3/1. © 1996 John Wiley & Sons, Inc.     

Low-stress encapsulants by vinylsiloxane modification

Dispersed silicone rubbers were used to reduce the stress of cresol–formaldehyde novolac epoxy resin cured with phenolic novolac resin for electronic encapsulation application. The effects of structure, molecular weight, and contents of the vinylsiloxane oligomer on reducing the stress of the encapsulant were investigated. Morphology and dynamic mechanical behavior of rubber-modified epoxy resins were also studied. The dispersed silicone rubbers effectively reduce the stress of cured epoxy resins by reducing flexural modulus and the coefficient of thermal expansion (CTE), whereas the glass transition temperature (T_g) was hardly depressed. Electronic devices encapsulated with the dispersed silicone rubber modified epoxy molding compounds have exhibited excellent resistance to the thermal shock cycling test and have resulted in an extended device use life. © 1994 John Wiley & Sons, Inc.     

Curing behavior of epoxy resin having hydroxymethyl group and different molecular weight distribution

o-Cresol novolac-type epoxy resins having hydroxymethyl group were synthesized. These epoxy resins were cured with a mixture of 4,4′-diaminodiphenylmethane and m-phenylenediamine (molar ratio, 6:4) as a hardener. Effects of molecular weight distribution of epoxy resins on curing behavior were studied. Curing behavior of epoxy resins with hardener were examined by differential scanning calorimetery (DSC), and cure reaction parameters were obtained. Viscoelastic properties of the cured epoxy resins were studied by dynamic mechanical analyzer. It was found that the lower the average molecular weight of the epoxy resin, that is, the higher the concentration of hydroxymethyl group, the shorter the onset time of exothermal reaction, the higher the rate constant (k), and the lower the activation energy (E_a) were. It was also found that glass transition temperature (T_g) of fully cured epoxy resins was higher than those of fully cured general novolac-type epoxy resins.     

Relationship between curing activation energy and free formaldehyde content in urea-formaldehyde resins

This study investigated the effect on the curing behavior, activation energy (E _a) of the curing reaction, crystalline structure, crosslinking, and free formaldehyde content of the addition of the following scavengers in urea-formaldehyde (UF) resins: medium density fiber board flour, rice husk flour, silica powder, and tannin powder. The scavenger content was 3 and 7?wt% of the UF resin solid content. The curing behavior of UF resins was monitored by differential scanning calorimetry, thermogravimetric analysis, and X-ray crystallography. The curing E _a was correlated to the free formaldehyde content of the scavenger containing UF resins. The thermal stability of the UF resins increased but the curing E _a decreased with increasing scavenger content. After curing, the crystallinity of the UF resins decreased in the presence of scavengers. The unreacted free formaldehyde content was reduced in the tannin powder containing UF resins. The degree of crosslinking affects the formaldehyde emission from wood panels bonded with UF resin. This is especially true for wood panels in service for long periods of time and exposed to high humidity conditions. Once the free formaldehyde which influences considerably the emission has disappeared, the presence of the –CH₂– groups then becomes important. Hence, an increased resin crosslinking indicates a higher concentration of –CH₂– groups present, which may hydrolyze and emit formaldehyde slowly over time.     

Nanoencapsulation mechanism of fragrant oil: effect of formaldehyde − melamine molar ratio

Encapsulation of essential oils by in situ polymerization is commonly used to contain the oil and thus ensure its controlled release. Melamine resin formaldehyde is one of the most widely used shell materials due to its thermal and chemical stability. One of the factors that influences the properties of the capsules is the molar relationship between monomers. The effect of formaldehyde ? melamine (F/M) molar ratios 3, 4 and 6 on the nanoencapsulation, morphology and properties of nanocapsules was investigated. The morphology and particle size were investigated by the scanning electron microscopy and atomic force microscopy techniques. The composition of the formaldehyde ? melamine resins was determined by Fourier transform infrared spectroscopy, and the thermal stability of the nanocapsules was analysed by differential scanning calorimetry and thermogravimetric analysis. Increasing the formaldehyde content reduced the nanocapsules' chemical stability. The capsule sizes obtained were nanometric at all melamine ? formaldehyde ratios studied, with a non‐significant variation in particle size and shape. © 2017 Society of Chemical Industry     

Development of a DOPO‐containing melamine epoxy hardeners and its thermal and flame‐retardant properties of cured products

In this study, a novel Schiff base of melamine used as flame‐retardant curing agent for epoxy resins, was synthesized via condensation reaction of 4‐hydroxybenzaldehyde with melamine, followed by the addition of 9,10‐dihydro‐9‐oxa‐10‐phosphaphen‐anthrene 10‐oxide (DOPO) to the resulting imine linkage. The structure of DOPO‐containing melamine Schiff base (P‐MSB) was characterized by Fourier transformed infrared spectroscopy, ¹H‐nuclear magnetic resonance (¹H‐NMR) and ³¹P‐NMR. The compound (P‐MSB) was used as a reactive flame retardant in o‐cresol formaldehyde novolac epoxy resin (CNE) to prepare flame‐retardant epoxy resins for electronic application. The thermal and flame‐retardant properties of the epoxy resins cured by various equivalent ratios phenol formaldehyde novolac (PN) and P‐MSB were investigated by the nonisothermal differential scanning calorimetry, the thermogravimetric analysis, and limiting oxygen index test. The obtained results showed that the cured epoxy resins possessed high T_g (165°C) and good thermal stability (T_5%, 321°C). Moreover, the P‐MSB/CNE systems exhibited higher limiting oxygen index (35) and more char was maintained in P‐MSB/CNE systems than that in PN/CNE system and the effective synergism of phosphorus–nitrogen indicated their excellent flame retardancy. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemical composition of melamine-urea-formaldehyde (MUF) resins assessed by near-infrared (NIR) spectroscopy

Melamine-urea-formaldehyde (MUF) resins are commonly used in the production of wood-based panels. The composition of the resin influences many properties of the final product. In industrial production, some properties, such as viscosity, pH, solid content, or molar ratio, are assessed after resin production in order to evaluate if they are within the desired parameters. These properties are useful for quality control of amino resins. However, almost no information is obtained if a certain type of reagent or filler is wrongly added to the formulation, even though the resin's final adhesive performance will be affected. Evaluation of the molar ratio of the reagents might be the only of the few industrially used tests capable of making this assessment. Near-infrared spectroscopy (NIR) is a fast and reliable technique for quality control of amino resins and can give a wide range of information regarding chemical composition of these products. This work intends to test the capability of NIR to assess several properties related to MUF resins’ chemical composition. The approach considered two types of problems: 1) whether there was a flaw on resin manufacture process and 2) which raw-material (amount or kind) was incorrectly added to the reactor. Using NIR spectra of a wide range of MUF resins, several models were established to predict the molar ratio of formaldehyde and urea (F/U), molar ratio of formaldehyde and melamine (F/M), molar ratio of formaldehyde and amino groups (F/(NH₂)₂), total urea (% U) and total melamine (% M). These models were constructed using the multivariate technique of Partial Least Squares (PLS) and could successfully determine the properties of a set of industrial resins. The coefficients of variation (CV) obtained were equal or lower than 5%, except for the property of F/M, which was 17%. A more thorough analysis of the established models reveals that spectral components of melamine are harder to extract by PLS than components of formaldehyde or urea.     

Syntheses and properties of low‐level melamine‐modified urea–melamine–formaldehyde resins

Syntheses of urea–melamine–formaldehyde (UMF) resins were studied using 2–12% melamine levels and UF base resins that were preadvanced to various different extents. The melamine reaction was carried out at pH 6.3 with F/(U + M) mole ratio of 2.1 until a target viscosity of V was reached (Gardener–Holdt) and then the second urea added at pH 8.0 to give a final F/(U + M) mole ratio of 1.15. Analyses with ¹³C‐NMR and viscosity measurements showed that MF components react fast and the UF components very slowly in the melamine reaction. Therefore, as the extent of preadvancement of UF base resin was decreased, the reaction time to reach the target viscosity became longer and the MF resin components showed high degrees of polymerization. The overpolymerization of MF components resulted in increasingly more opaque resins, with viscosity remaining stable for more than a month. As the preadvancement of UF base resin was increased, the extent of advancement of MF components decreased, to give clearer resins, with viscosity slowly increasing at room temperature. Overall, preadvancing the UF base resin components to an appropriate extent was found to be a key to synthesizing various low‐level melamine‐modified UMF resins. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2559–2569, 2004