Influence of LiClO4 on the thermal,mechanical, and morphological properties of P(DMS‐co‐EO)/ P(EPI‐co‐EO) blends

The UV‐vis absorption, thermal analysis, ionic conductivity, mechanical properties, and morphology of a blend of poly(dimethylsiloxane‐co‐ethylene oxide) [P(DMS‐co‐EO)] and poly(epichlorohydrin‐co‐ethylene oxide) [P(EPI‐co‐EO)] (P(DMS‐co‐EO)/P(EPI‐co‐EO) ratio of 15/85 wt %) with different concentrations of LiClO₄ were studied. The maximum ionic conductivity (σ = 1.2 × 10^?4 S cm^?1) for the blend was obtained in the presence of 6% wt LiClO₄. The crystalline phase of the blend disappeared with increasing salt concentration, whereas the glass transition temperature (T_g) progressively increased. UV‐vis absorption spectra for the blends with LiClO₄ showed a transparent polymer electrolyte in the visible region. The addition of lithium salt decreased the tensile strength and elongation at break and increased Young's modulus of the blends. Scanning electron microscopy showed separation of the phases between P(DMS‐co‐EO) and P(EPI‐co‐EO), and the presence of LiClO₄ made the blends more susceptible to cracking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1230–1235, 2004     

Synthesis and surface‐active properties of a trisiloxane‐modified oligo(propylene oxide‐block‐ethylene oxide) wetting agent

Polydisperse 1,1,1,3,5,5,5‐heptamethyltrisiloxane‐oligo(propylene oxide‐block‐ethylene oxide) wetting agents were synthesized through the hydrosilylation of 1,1,1,3,5,5,5‐heptamethyltrisiloxane (HMTS) with active hydrogen and allyl oligo(propylene oxide‐block‐ethylene oxide) [allyl oligo(PO‐b‐EO)] with hexachloro dihydrogen platinate(IV) as a catalyst. Allyl oligo(PO‐b‐EO) with a hydrophilic–hydrophobic balance was synthesized through the combination of propylene oxide (PO) and ethylene oxide with allyl alcohol. The wetting agents with a hydrophilic–hydrophobic balance were synthesized. The aqueous solutions of the wetting agents (0.1 wt %) were almost visibly turbid. An increase in the number of hydrophobic groups of HMTS and PO for the wetting agents resulted in a lower critical solution temperature. Lower surface tensions of 20–25 dyn/cm were found above the critical micelle concentration (cmc), and they decreased with an increase in the number of hydrophobic groups. The cmc's were below 0.01 wt %, decreasing with as the number of hydrophobic groups increased. The wetting power and emulsion stability for the oil‐in‐water systems increased as the concentration of the wetting agents increased, and they decreased as the number of hydrophobic groups increased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3292–3302, 2004     

Conducting properties of iodine‐doped low‐density polyethylene–poly(4‐vinylpyridine) blends

The conductivities of blends of low‐density polyethylene and poly(4‐vinyl pyridine) (P4VP) were studied. The blends were synthesized by in situ sorption and thermal polymerization of 4‐vinylpyridine in low‐density polyethylene. They showed, after iodine doping, conductivities of 1.7 to 5.0 × 10^?7 S cm^?1 at 298 K, depending on the P4VP mass increment into the matrix. Their conductivities were one order of magnitude higher for measurements at 338 K. The optimum ratio of iodine to pyridine (n) which gave the highest conductivity was 0.21. The thermal stability of doped blends was acceptable for their uses as electrochemical devices. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 939–944, 2003     

The investigation of novel non‐metallocene catalysts with phenoxy‐imine ligands for ethylene (co‐)polymerization

Phthaldialdehyde and phthaldiketone were treated with substituted phenols of 2‐amino‐4‐methylphenol, 2‐amino‐5‐methylphenol and 2‐amino‐4‐t‐butylphenol, respectively, and then treated with transition metal halides of TiCl₄, ZrCl₄ and YCl₃. A series of novel non‐metallocene catalysts (1–12) with phenoxy‐imine ligands was obtained. The structures and properties of the catalysts were characterized by ¹H NMR and elemental analysis. The catalysts (1–12) were used to promote ethylene (co‐)polymerization after activation by methylaluminoxane. The effects of the structures and center atoms (Ti, Zr and Y) of these catalysts, polymerization temperature, Al/M (M = Ti, Zr and Y) molar ratio, concentration of the catalysts and solvents on the polymerization performance were investigated. The results showed that the catalysts were favorable for ethylene homopolymerization and copolymerization of ethylene with 1‐hexene. Catalyst 10 is most favorable for catalyzing ethylene homopolymerization and copolymerization of ethylene with 1‐hexene, with catalytic activity up to 2.93 × 10⁶ gPE (mol Y)^?1 h^?1 for polyethylene (PE) and 2.96 × 10⁶ gPE (mol Y)^?1 h^?1 for copolymerization of ethylene with 1‐hexene under the following conditions: polymerization temperature 50 °C, Al/Y molar ratio 300, concentration of catalyst 1.0 × 10^?4 L^?1 and toluene as solvent. The structures and properties of the polymers obtained were characterized by Fourier transform infrared spectroscopy, ¹³C NMR, wide‐angle X‐ray diffraction, gel permeation chromatography and DSC. The results indicated that the obtained PE catalyzed by 4 had the highest melting point of 134.8 °C and the highest weight‐average molecular weight of 7.48 × 10⁵ g mol^?1. The copolymer catalyzed by 4 had the highest incorporation of 1‐hexene, up to 5.26 mol%, into the copolymer chain. © 2012 Society of Chemical Industry     

Crystallization behavior of PEO in blends of poly(ethylene oxide)/poly(2‐vinyl pyridine)‐b‐(ethylene oxide) block copolymer

The crystallization behavior of two molecular weight poly(ethylene oxide)s (PEO) and their blends with the block copolymer poly(2‐vinyl pyridine)‐b‐poly(ethylene oxide) (P2VP‐b‐PEO) was investigated by polarized optical microscopy, thermogravimetric analysis, differential scanning calorimetry, and atomic force microscopy (AFM). A sharp decreasing of the spherulite growth rate was observed with the increasing of the copolymer content in the blend. The addition of P2VP‐b‐PEO to PEO increases the degradation temperature becoming the thermal stability of the blend very similar to that of the block copolymer P2VP‐b‐PEO. Glass transition temperatures, T_g, for PEO/P2VP‐b‐PEO blends were intermediate between those of the pure components and the value increased as the content of PEO homopolymer decreased in the blend. AFM images showed spherulites with lamellar crystal morphology for the homopolymer PEO. Lamellar crystal morphology with sheaf‐like lamellar arrangement was observed for 80 wt% PEO(200M) and a lamellar crystal morphology with grain aggregation was observed for 50 and 20 wt% blends. The isothermal crystallization kinetics of PEO was progressively retarded as the copolymer content in the blend increased, since the copolymer hinders the molecular mobility in the miscible amorphous phase. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

Synthesis and characterization of homo‐ and copolymers of 3‐(2‐cyano ethoxy)methyl‐ and 3‐[methoxy(triethylenoxy)]methyl‐3′‐methyl‐oxetane

Two oxetane‐derived monomers 3‐(2‐cyanoethoxy)methyl‐ and 3‐(methoxy(triethylenoxy)) methyl‐3′‐methyloxetane were prepared from the reaction of 3‐methyl‐3′‐hydroxymethyloxetane with acrylonitrile and triethylene glycol monomethyl ether, respectively. Their homo‐ and copolyethers were synthesized with BF₃· Et₂O/1,4‐butanediol and trifluoromethane sulfonic acid as initiator through cationic ring‐opening polymerization. The structure of the polymers was characterized by FTIR and¹H NMR. The ratio of two repeating units incorporated into the copolymers is well consistent with the feed ratio. Regarding glass transition temperature (T_g), the DSC data imply that the resulting copolymers have a lower T_g than pure poly(ethylene oxide). Moreover, the TGA measurements reveal that they possess in general a high heat decomposition temperature. The ion conductivity of a sample (P‐AN 20) is 1.07 × 10^?5 S cm^?1 at room temperature and 2.79 × 10^?4 S cm^?1 at 80 °C, thus presenting the potential to meet the practical requirement of lithium ion batteries for polymer electrolytes. Copyright © 2005 Society of Chemical Industry     

Ionic conductivity and morphology of semi‐interpenetrating‐type polymer electrolyte entrapping poly(siloxane‐g‐allyl cyanide)

We prepared a semi‐IPN (interpenetrating network)‐type solid polymer electrolyte (SPE) using poly (ethylene glycol)dimethacrylate (PEGDMA) as a polymer matrix containing a monocomb‐type poly(siloxane‐g‐allyl cyanide) and poly(ethylene glycol)dimethylether (PEGDME) for the lithium secondary battery. The poly(siloxane‐g‐allyl cyanide)s were prepared by a hydrosilation reaction of poly (methyl hydrosiloxane) with allyl cyanide and characterized by ¹H NMR and FTIR. The semi‐IPN‐type electrolyte was prepared by thermal curing, and conductivities of samples were measured by impedance spectroscopy using an indium tin oxide (ITO) electrode. The ionic conductivity of the semi‐IPN‐polymer electrolyte was about 1.05 × 10^?5 S cm^?1 with 60 wt % of the poly(siloxane‐g‐allyl cyanide) and 6.96 × 10^?4 S cm^?1 with 50 wt % of the PEGDME and 10 wt % of the poly(siloxane‐g‐allyl cyanide) at 30°C. The SEM morphology of the cross section of the semi‐IPN‐polymer electrolyte film was changed from discontinuous network to continuous network as increasing the PEGDME content and decreasing the poly(siloxane‐g‐allyl cyanide) content. The mechanical stability was also enhanced when increasing the PEGDME content. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of molecular weight on dual light‐ and thermo‐responsive behaviors of homopolymers with azobenzene units and terminal oligo(ethylene glycol) units

A series of water‐soluble dual light‐ and thermo‐responsive homopolymers bearing azobenzene units and terminal oligo(ethylene glycol) units with well‐defined molecular weight (M _n = 0.69 × 10⁴ to 4.60 × 10⁴ g mol^?1) were synthesized via reversible addition–fragmentation chain transfer polymerization. All the homopolymers exhibited reversible photoisomerization and their lower critical solution temperatures showed an unusual increase with increasing molecular weight. Interestingly, by increasing the molecular weight, the aggregate morphology of these polymers was found to evolve from a spherical to a cylindrical shape. © 2017 Society of Chemical Industry     

pH‐ and temperature‐sensitive microfiltration membranes from blends of poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) and poly(N‐isopropylacrylamide)

The copolymer poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) (PVDF‐g‐P4VP) was prepared through the graft copolymerization of poly(vinylidene fluoride) with 4‐vinylpyridine. Through the blending of the PVDF‐g‐P4VP copolymer with poly(N‐isopropylacrylamide) (PNIPAm) in an N‐methyl‐2‐pyrrolidone solution, PVDF‐g‐P4VP/PNIPAm membranes were fabricated by phase inversion in aqueous media. Elemental analyses indicated that the blend concentration of PNIPAm in the blend membranes increased with an increase in the blend ratio used in the casting solution. Scanning electron microscopy revealed that the membrane surface tended to corrugate at a low PNIPAm concentration and transformed into a smooth morphology at a high PNIPAm concentration. The surface morphology and pore size distribution of the microfiltration membranes could be regulated by the blend concentration of the casting solution, temperature, pH, and ionic strength of the coagulation bath. X‐ray photoelectron spectroscopy revealed a significant enrichment of PNIPAm on the membrane surface. The flux of aqueous solutions through the blend membranes exhibited a pH‐ and temperature‐dependent behavior. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4089–4097, 2006     

Effect of side‐chain functionality on the organic field‐effect transistor performance of oligo(p‐phenylenevinylene) derivatives

In order to observe the effects of the substitution of electronegative flourine with aromatic groups in oligo(p ‐phenylenevinylene) compounds on their packing, morphology, and charge carrier mobility, we have synthesized napthol‐substituted oligo(p ‐phenylenevinylene) compounds and examined their solubility, redox properties, thin film morphologies, and charge carrier properties. To date, very few examples of conjugated oligomers bearing napthol side groups have been reported in the literature. After annealing at 150 °C, the mobility of S1, S2, and S3 was 4.0 × 10^?2 cm² V^?1 s^?1, 1.2 × 10^?2 cm² V^?1 s^?1, and 2.6 × 10^?3 cm² V^?1 s^?1, respectively. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44825.     

Thermoresponsive poly(γ‐propyl‐l‐glutamate)‐graft‐(oligo ethylene glycol)s: Synthesis,characterization, and properties

A series of thermoresponsive poly(γ‐propyl‐_L‐glutamate)‐graft‐(oligo ethylene glycol)s (PPLG‐g‐OEGs) with different main‐chain and side‐chain lengths have been synthesized via copper‐mediated alkyne‐azide 1,3‐dipolar cycloaddition between poly(γ‐azidopropyl‐_L‐glutamate)s (PAPLG) and propargyl terminated oligo ethylene glycols (Pr‐OEGs). Fourier transform infrared spectrometer analysis revealed that PAPLG₁₀ adopted 39.4% β‐sheet, 47.4% α‐helix, and 13.2% random coil while PAPLG with longer main‐chain length (DP = 37 and 88) and PPLG‐g‐OEGs adopted exclusive α‐helix in the solid state. Circular dichroism analysis revealed that PPLG‐g‐OEGs adopted α‐helical conformations with helicities in the range of 50～100%. The thermoresponsive behaviors of PPLG‐g‐OEGs in water have been studied by dynamic light scattering. The polymer concentration, main‐/side‐chain length, and helicity collectively affected their cloud point temperatures. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41022.     

Synthesis of new ionic crosslinked polymer hydrogel combining polystyrene and poly(4‐vinyl pyridine) and its self‐healing through a reshuffling reaction of the trithiocarbonate moiety under irradiation of ultraviolet light

A new ionic crosslinked polymer hydrogel was achieved by the strategy of ionically crosslinking α,ω‐dibromide terminated polystyrene (Br‐PS‐Br) with poly(4‐vinyl pyridine) (P4VP) which was synthesized by reversible addition‐fragmentation chain transfer polymerization using a chain transfer agent containing a trithiocarbonate moiety. The moiety of trithiocarbonate was introduced into the crosslinked network to show the self‐healing characteristics. The chain structure and components of Br‐PS‐Br and P4VP were characterized through ¹H NMR, gel permeation chromatography, Fourier transform IR spectroscopy and elemental analysis. The P4VP (M_n = 25 300 g mol^?1) chains were crosslinked with Br‐PS‐Br (M_n = 2000 g mol^?1) through the quaternization reaction to form a polymer network which was further crosslinked in acetonitrile by irradiation of UV light to fabricate a hydrogel. Such a hydrogel of P4VP/Br‐PS‐Br cut by a razor blade can be rapidly (1 h) and repeatedly (three times) healed through a reshuffling reaction of the trithiocarbonate moiety under irradiation by UV light. © 2018 Society of Chemical Industry     

Micellization of pH‐sensitive poly(butadiene)‐block‐poly(2 vinylpyridine)‐block‐poly(ethylene oxide) triblock copolymers: Complex formation with anionic surfactants

The micellization of three tailor‐made triblock copolymers, such as PB₁₀₀–P2VP₁₀₀–PEO₁₀₄, PB₁₈₅–P2VP₁₀₈–PEO₁₅₄, and PB₃₇–P2VP₁₁₅–PEO₂₄₁, having similar total molecular weights and constant poly(2‐vinylpyridine) (P2VP) sequence lengths, was investigated as a function of pH and sodium dodecyl sulfate (SDS) concentration. At pH 7 the formation of intermicellar aggregates was observed, especially for copolymers of low poly(ethylene oxide) (PEO) content. A pH decrease from 7 to 3 leads to a particle size increase due to the electrostatic repulsion of the protonated P2VP chains. The influence of the PEO sequence length was also observed for zeta potential values. At pH 3, in the absence of SDS, core–shell–corona micelles are formed whereas in the presence of small amount of SDS (degree of neutralization DN = 0%–50%), a complex is formed between SDS and the protonated P2VP which leads to the shrinkage of the shell and thus to a decrease of the micellar sizes. For higher DN values, the micellar sizes increase due to the formation of large agglomerates and a transition occurs from a monomodal to a bimodal size distribution. Furthermore, it turned out that secondary aggregation, such as intermicellar aggregation, can completely be avoided if the degree of polymerization (DPn) of the water‐soluble block is significantly higher than the DPn of the water‐insoluble sequence. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45313.     

Formation of honeycomb films from poly(L‐lactide)‐block‐poly(ethylene glycol) via water‐droplet templating

The fabrication of honeycomb‐patterned films from amphiphilic poly(L ‐lactide)‐block‐poly(ethylene glycol) (PLEG) in a high‐humidity atmosphere is reported. The influence of the solution concentration on pattern formation was investigated. Moreover, by comparing the different conditions of fabricating regular structures between PLEG and poly(phenylene oxide), the mechanism of the regular pattern formation was studied. Finally, by adding sodium dodecylsulfate to a concentrated solution of 1 g L^?1 PLEG? CHCl₃ which otherwise could not form regular pores, we found that regular pores could be obtained. The PLEG honeycomb films are expected to be of use in cell culture, tissue engineering and many other areas. Copyright © 2007 Society of Chemical Industry     

Poly(4‐vinyl pyridine)‐grafted graphene oxide for drug delivery and antimicrobial applications

Graphene oxide (GO) was covalently functionalized with poly(4‐vinyl pyridine) (P4VP) by atom transfer radical polymerization for drug delivery and antimicrobial applications. The physiochemical properties, chemical structure, composition and morphology of the P4VP‐functionalized GO (GO‐P4VP) were studied. Simple physisorption of a cancer drug, camptothecin (CPT), via π ? π stacking and/or hydrophobic interactions on the GO‐P4VP was tested for drug loading and its release by altering the pH. The GO‐P4VP has low cytotoxicity, and the CPT‐loaded GO‐P4VP exhibited a high potency for killing cancer cells in vitro. Prominent antimicrobial properties against Escherichia coli and Staphylococcus aureus were also observed. Thus, the GO‐P4VP can be utilized as a drug delivery vector with high biocompatibility, solubility and stability in physiological solutions, a suitable payload capacity and excellent bacterial toxicity. Owing to its small size, low cost, large specific area, ready scalability and useful non‐covalent interactions, GO‐P4VP is a novel material for biomedical, industrial and environmental applications. © 2015 Society of Chemical Industry     

Novel amphiphilic polymer gel electrolytes based on (PEG‐b‐GMA)‐co‐MMA

Amphiphilic conetwork–structured copolymers containing different lengths of ethylene oxide (EO) chains as ionophilic units and methyl methacrylate (MMA) chains as ionophobic units were prepared by free radical copolymerization and characterized by FTIR and thermal analysis. Polymer gel electrolytes based on the copolymers complexed with liquid lithium electrolytes (dimethyl carbonate (DMC) : diethyl carbonate (DEC) : ethylene carbonate (EC) = 1 : 1 : 1 (W/W/W), LiPF₆ 1.0M) were characterized by differential scanning calorimetry and impedance spectroscopy. A maximum ion conductivity of 4.27 × 10^?4 S/cm at 25^oC was found for the polymer electrolyte based on (PEG2000‐b‐GMA)‐co‐MMA with long EO groups. Moreover, the effect of temperature on conductivity of the amphiphilic polymer electrolytes obeys the Arrhenius equation. The good room temperature conductivity of the polymer electrolytes is proposed to relate to the enhancement in the amorphous domain of the copolymers due to their amphiphilic conetwork structure. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Efficiency above 6% in poly(3‐hexylthiophene):phenyl‐C‐butyric acid methyl ester photovoltaics via simultaneous addition of poly(3‐hexylthiophene) based grafted graphene nanosheets and hydrophobic block copolymers

A combination of reduced graphene oxide (rGO) nanosheets grafted with regioregular poly(3‐hexylthiophene) (P3HT) (rGO‐g‐P3HT) and P3HT‐b‐polystyrene (PS) block copolymers was utilized to modify the morphology of P3HT:[6,6]‐phenyl‐C71‐butyric acid methyl ester (PC71BM) active layers in photovoltaic devices. Efficiencies greater than 6% were acquired after a mild thermal annealing. To this end, the assembling of P3HT homopolymers and P3HT‐b‐PS block copolymers onto rGO‐g‐P3HT nanosheets was investigated, showing that the copolymers were assembled from the P3HT side onto the rGO‐g‐P3HT nanosheets. Assembling of P3HT‐b‐PS block copolymers onto the rGO‐g‐P3HT nanosheets developed the net hole and electron highways for charge transport, thereby in addition to photoluminescence quenching the charge mobility (μ_h and μ_e) values increased considerably. The best charge mobilities were acquired for the P3HT₅₀₀₀₀:PC71BM:rGO‐g‐P3HT₅₀₀₀₀:P3HT₇₀₀₀‐b‐PS₁₀₀₀ system (μ_h = 1.9 × 10^?5 cm² V^–1 s^–1 and μ_e = 0.8 × 10^?4 cm² V^–1 s^–1). Thermal annealing conducted at 120 °C also further increased the hole and electron mobilities to 9.8 × 10^?4 and 2.7 × 10^?3 cm² V^–1 s^–1, respectively. The thermal annealing acted as a driving force for better assembly of the P3HT‐b‐PS copolymers onto the rGO‐g‐P3HT nanosheets. This phenomenon improved the short circuit current density, fill factor, open circuit voltage and power conversion efficiency parameters from 11.13 mA cm^?2, 0.63 V, 62% and 4.35% to 12.98 mA cm^?2, 0.69 V, 68% and 6.09%, respectively. © 2019 Society of Chemical Industry     

Biocompatible,ionic‐strength‐sensitive,double‐network hydrogel based on chitosan and an oligo(trimethylene carbonate)–poly(ethylene glycol)–oligo(trimethylene carbonate) triblock copolymer

A double‐network (DN) hydrogel was prepared through the sequential photopolymerization of oligo(trimethylene carbonate) (TPT)‐block‐poly(ethylene glycol)‐block‐oligo(trimethylene carbonate) diarylate and methacrylated chitosan (CS–MA). The swelling behavior and mechanical properties of the hydrogels were tunable via the control of the concentration of CS–MA. Under physiological conditions, the fracture stress of the DN hydrogel reached 3.4 MPa; this was more than twice that of the corresponding TPT‐block‐poly(ethylene glycol)‐block‐TPT single network (1.6 MPa). At high ionic strength, the fracture stress of the DN hydrogel reached 6.4 MPa. The DN hydrogel exhibited good cytocompatibility, as revealed by a live–dead assay. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42459.     

Rheological properties of poly(ethylene glycol)/poly(N‐isopropylacrylamide‐co‐2‐acrylamido‐2‐methylpropanesulphonic acid) semi‐interpenetrating networks

For the increasing demands of multifunctional materials in applications such as drug delivery system, a pH‐ and temperature‐responsive polyelectrolyte copolymer gel system was studied using rheometry. Rheological properties, determined by plate–plate rheometry in oscillatory shear, of hydrogels formed by free radical initiated copolymerization of N‐isopropylacrylamide (NIPA) and 2‐acrylamido‐2‐methylpropanesulphonic acid (AMPS) in the presence of methylene bisacrylamide (MBAA) as crosslinker are compared with the properties of semi‐interpenetrating network (SIPN) polyelectrolyte gels made by incorporation of poly(ethylene glycol) with molar mass 6000 g mol^?1 (PEG6000). Based on our systematic studies for this PEG/SIPN system, the effects of initiator and crosslinker concentration, relative proportions of comonomer units in the main chains, PEG6000 content and temperature on viscoelastic properties, unusual high storage moduli at small strain for the SIPN were discussed. The SIPN gel with characteristics of PEG molecules as well as pH and temperature responsiveness from AMPS and NIPA units has potential application in drug delivery system design. Ice‐like rheological behavior of the PEG/AMPS‐NIPA SIPN gels at low temperature was first time reported and water remains homogeneous without phase separation in PEG/AMPS‐NIPA SIPN hydrogels at low temperature may be considered as an ideal candidate for water storage material. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study on synthesis and morphology control of poly(4‐vinylpyridine‐co‐butyl acrylate)/poly(styrene‐co‐butyl acrylate) composite microspheres

Monodispersed crosslinked cationic poly(4‐vinylpyridine‐co‐butyl acrylate) [P(4VP‐BA)] seed latexes were prepared by soapless emulsion polymerization, using 2,2′‐azobismethyl(propionamidine)dihydrochloride (V₅₀) as an initiator and divinylbenzene (DVB) or ethylene glycol dimethacrylate (EGDMA) as a crosslinker. The optimum condition to obtain monodispersed stable latex was investigated. It was found that the colloidal stability of the P4VP latex can be improved by adding an adequate amount of BA (BA/4VP = 1/4, w/w), and adopting a semicontinuous monomer feed mode. Subsequently, poly(4‐vinylpyridine‐co‐butyl acrylate)/Poly(styrene‐co‐butyl acrylate) [P(4VP‐BA)/P(ST‐BA)] composite microspheres were synthesized by seeded polymerization, using the above latex as a seed and a mixture of ST and BA as the second‐stage monomers. The effects of the type of crosslinker, the degree of crosslinking, and the initiators (AIBN and V₅₀) on the morphology of final composite particles are discussed in detail. It was found that P(4VP‐BA)/P(ST‐BA) composite microspheres were always surrounded by a PST‐rich shell when V₅₀ was used as initiator, while sandwich‐like or popcorn‐like composite particles were produced when AIBN was employed. This is because the polarity of the polymer chains with AIBN fragments is lower than for the polymer with V₅₀ fragments, hence leading to higher interfacial tension between the second‐stage PST‐rich polymer and the aqueous phase, and between PST‐rich polymer and P4VP‐rich seed polymer. As a result, the seed cannot be engulfed by the PST‐rich polymer. Furthermore, the decrease of T_g of the second‐stage polymer promoted phase separation between the seeds and the PST‐rich polymer: sandwich‐like particles formed more preferably than popcorn‐like particles. It is important knowledge that various morphologies different from PST‐rich core/P4VP‐rich shell morphology, can be obtained only by changing the initiator, considering P4VP is much more hydrophilic than PST. The zeta potential of composite particles initiated by AIBN in seeded polymerization shifted from a positive to a negative charge. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1190–1203, 2002