Synthesis and characterization of thermoplastic poly(ester–siloxane)s

Two series of thermoplastic poly(ester–siloxane)s, based on poly(dimethylsiloxane) (PDMS) as the soft segment and poly(butylene terephthalate) as the hard segment, were synthesized by two‐step catalyzed transesterification reactions in the melt. Incorporation of soft poly(dimethylsiloxane) segments into the copolyester backbone was accomplished in two different ways. The first series was prepared based on dimethyl terephthalate, 1,4‐butanediol and silanol‐terminated poly(dimethylsiloxane) (PDMS‐OH). For the second series, the PDMS‐OH was replaced by methyl diesters of carboxypropyl‐terminated poly(dimethylsiloxane)s. The syntheses were optimized in terms of both the concentration of catalyst, tetra‐n‐butyl‐titanate (Ti(OBu)₄), and stabilizer, N,N′‐diphenyl‐p‐phenylene‐diamine, as well as the reaction time. The reactions were followed by measuring the inherent viscosities of the reaction mixture. The molecular structures of the synthesized poly(ester–siloxane)s were verified by ¹H NMR spectroscopy, while their thermal properties were investigated using differential scanning calorimetry. © 2001 Society of Chemical Industry     

Synthesis and characterization of poly(ester ether siloxane)s

A series of novel thermoplastic elastomers based on ABA‐type triblock prepolymers, poly[(propylene oxide)–(dimethylsiloxane)–(propylene oxide)] (PPO‐PDMS‐PPO), as the soft segments, and poly(butylene terephthalate) (PBT), as the hard segments, was synthesized by catalyzed two‐step melt transesterification of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) (M?_n = 2930 g mol^?1). Several copolymers with a content of hard PBT segments between 40 and 60 mass% and a constant length of the soft PPO‐PDMS‐PPO segments were prepared. The siloxane‐containing triblock prepolymer with hydrophilic terminal PPO blocks was used to improve the compatibility between the polar comonomers, i.e. DMT and BD, and the non‐polar PDMS segments. The structure and composition of the copolymers were examined using ¹H NMR spectroscopy, while the effectiveness of the incorporation of α,ω‐dihydroxy‐(PPO‐PDMS‐PPO) prepolymer into the copolyester chains was controlled by chloroform extraction. The effect of the structure and composition of the copolymers on the transition temperatures (T_m and T_g) and the thermal and thermo‐oxidative degradation stability, as well as on the degree of crystallinity, and some rheological properties, were studied. Copyright © 2006 Society of Chemical Industry     

Synthesis and characterization of hyperbranched poly(silyl ester)s

Hyperbranched poly(silyl ester)s were synthesized via the A₂ + B₄ route by the polycondensation reaction. The solid poly(silyl ester) was obtained by the reaction of di‐tert‐butyl adipate and 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The oligomers with tert‐butyl terminal groups were obtained via the A₂ + B₂ route by the reaction of 1,5‐dichloro‐1,1,5,5‐tetramethyl‐3,3‐diphenyl‐trisi1oxane with excess amount of di‐tert‐butyl adipate. The viscous fluid and soft solid poly(silyl ester)s were obtained by the reaction of the oligomers as big monomers with 1,3‐tetramethyl‐1,3‐bis‐β(methyl‐dicholorosilyl)ethyl disiloxane. The polymers were characterized by ¹H NMR, IR, and UV spectroscopies, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The ¹H NMR and IR analysis proved the existence of the branched structures in the polymers. The glass transition temperatures (T_g's) of the viscous fluid and soft solid polymers were below room temperature. The T_g of the solid poly(silyl ester) was not found below room temperature but a temperature for the transition in the liquid crystalline phase was found at 42°C. Thermal decomposition of the soft solid and solid poly(silyl ester)s started at about 130°C and for the others it started at about 200°C. The obtained hyperbranched polymers did not decompose completely at 700°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3430–3436, 2006     

Synthesis and characterization of biodegradable poly(ester‐urethanes) based on bacterial poly(R‐3‐hydroxybutyrate)

A series of poly(R‐3‐hydroxybutyrate)/poly(ε‐caprolactone)/1,6‐hexamethylene diisocyanate‐segmented poly(ester‐urethanes), having different compositions and different block lengths, were synthesized by one‐step solution polymerization. The molecular weight of poly(R‐3‐hydroxybutyrate)‐diol, PHB‐diol, hard segments was in the range of 2100–4400 and poly(ε‐caprolactone)‐diol, PCL‐diol, soft segments in the range of 1080–5800. The materials obtained were investigated by using differential scanning calorimetry, wide angle X‐ray diffraction and mechanical measurements. All poly(ester‐urethanes) investigated were semicrystalline with T_m varying within 126–148°C. DSC results showed that T_g are shifted to higher temperature with increasing content of PHB hard segments and decreasing molecular weight of PCL soft segments. This indicates partial compatibility of the two phases. In poly(ester‐urethanes) made from PCL soft segments of molecular weight (M_n ≥ 2200), a PCL crystalline phase, in addition to the PHB crystalline phase, was observed. As for the mechanical tensile properties of poly(ester‐urethane) cast films, it was found that the ultimate strength and the elongation at the breakpoint decrease with increasing PHB hard segment content. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 703–718, 2002     

Synthesis and characterization of biodegradable aliphatic copolyesters with poly(tetramethylene oxide) soft segments

A series of aliphatic poly(ether–ester)s based on flexible poly(tetramethylene oxide) (PTMO) and hard poly (butylene succinate) (PBS) segments were synthesized by the catalyzed two‐step transesterification reaction of dimethyl succinate, 1,4‐butanediol, and α,ω‐hydroxy‐terminated PTMO (M_n = 1000 g/mol) in the bulk. The content of soft PTMO segments in the polymer chains was varied from 10 to 50 mass %. The effect of the introduction of the soft segments on the structure, thermal, and physical properties, as well as on the biodegradation properties was investigated. The composition and structure of the aliphatic segmented copolyesters were determined by ¹H NMR spectroscopy. The molecular weights of the polyesters were verified by viscometry of dilute solutions and polymer melts. The thermal properties were investigated using DSC. The degree of crystallinity was determined by means of DSC and WAXS. Biodegradation of the synthesized copolyesters, estimated in enzymatic degradation tests on polymer films in phosphate buffer solution with Candida rugosa lipase at 37°C, was compared with hydrolytic degradation in the buffer solution. Viscosity measurements confirmed that there was no change in molecular weight of the copolyesters leading to the conclusion that the degradation mechanism of poly(ester–ether)s based on PTMO segments occurs through the surface erosion. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterization of copolymers based on poly(butylene terephthalate) and ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide

A series of thermoplastic elastomers based on ethylene oxide‐poly(dimethylsiloxane)‐ethylene oxide (EO‐PDMS‐EO), as the soft segment, and poly(butylene terephthalate) (PBT), as the hard segment, were synthesized by catalyzed two‐step, melt transesterification reaction of dimethyl terephthalate (DMT) with 1,4‐butanediol (BD) and α,ω‐dihydroxy‐(EO‐PDMS‐EO). Copolymers with a content of hard PBT segments between 40 and 90 mass % and a constant length of the soft EO‐PDMS‐EO segments were prepared. The siloxane prepolymer with hydrophilic terminal EO units was used to improve the miscibility between the polar comonomers, DMT and BD, and the nonpolar PDMS. The molecular structure and composition of the copolymers were determined by ¹H‐NMR spectroscopy, whereas the effectiveness of the incorporation of α,ω‐dihydroxy‐(EO‐PDMS‐EO) into the copolymer chains was verified by chloroform extraction. The effects of the structure and composition of the copolymers on the melting temperatures and the degree of crystallinity, as well as on the thermal degradation stability and some rheological properties, were studied. It was demonstrated that the degree of crystallinity, the melting and crystallization temperatures of the copolymers increased with increasing mass fraction of the PBT segments. The thermal stability of the copolymers was lower than that of PBT homopolymer, because of the presence of thermoliable ether bonds in the soft segments. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis,characterisation, and chemical degradation of segmented polyurethanes with butylamine for chemical recycling

Polyurethane elastomers (PU) have been synthesized from polytetramethylene glycol 2000 (PTMG 2000); 4, 4′‐diphenylmethane diisocyanate (MDI) and 1, 4‐butanediol (BD) as chain extender. This synthesis has been done in two steps known as prepolymer methods. The concentration of soft segments and hydrogen attachment in the matrices, have been studied. The results show that the glass transition of the soft segment T_g(s) do not take any changes with the concentration of the soft segment in the matrices. Although, the glass transition temperature of the hard segment T_g(H) increases when the concentration of the hard segment increases in the matrices. In general, the properties of the polyurethane elastomers depend on the extenders nature, the synthesis methods, phase segregation etc. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of poly(urethane‐ester)s based on calcium salt of mono(hydroxybutyl)phthalate

Calcium‐containing poly(urethane‐ester)s (PUEs) were prepared by reacting diisocyanate (HMDI or TDI) with a mixture of calcium salt of mono(hydroxybutyl)phthalate [Ca(HBP)₂] and hydroxyl‐terminated poly(1,4‐butylene glutarate) [HTPBG₁₀₀₀], using di‐n‐butyltin‐dilaurate as catalyst. About six calcium‐containing PUEs having different composition were synthesized by taking the mole ratio of Ca(HBP)₂:HTPBG₁₀₀₀:diisocyanate (HMDI or TDI) as 3:1:4, 2:2:4, and 1:3:4. Two blank PUEs were synthesized by the reaction of HTPBG₁₀₀₀ with diisocyanate (HMDI or TDI). The polymers were characterized by IR, ¹H NMR, Solid state ¹³C‐CP‐MAS NMR, TGA, DSC, XRD, solubility, and viscosity studies. The T_g value of PUEs increases with increase in the calcium content and decreases with increase in soft segment content. The viscosity of the calcium‐containing PUEs increases with increase in the soft segment content and decreases with increase in the calcium content. X‐ray diffraction patterns of the polymers show that the HMDI‐based polymers are partially crystalline and TDI‐based polymers are amorphous in nature. The dynamic mechanical analysis of the calcium‐containing PUEs based on HMDI shows that with increase in the calcium content of polymer, modulus (g′ and g″) increases at any given temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1720–1727, 2006     

Effect of annealing on poly(urethane‐siloxane) copolymers

Poly(urethane‐siloxane) copolymers were prepared by copolymerization of OH‐terminated polydimethylsiloxane (PDMS), which was utilized as the soft segment, as well as 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (1,4‐BD), which were both hard segments. These copolymers exhibited almost complete phase separation between soft and hard segments, giving rise to a very simple material structure in this investigation. The thermal behavior of the amorphous hard segment of the copolymer with 62.3% hard‐segment content was examined by differential scanning calorimetry (DSC). Both the T₁ temperature and the magnitude of the T₁ endotherm increased linearly with the logarithmic annealing time at an annealing temperature of 100°C. The typical enthalpy of relaxation was attributed to the physical aging of the amorphous hard segment. The T₁ endotherm shifted to high temperature until it merged with the T₂ endotherm as the annealing temperature increased. Following annealing at 170°C for various periods, the DSC curves presented two endothermic regions. The first endotherm assigned as T₂ was the result of the enthalpy relaxation of the hard segment. The second endothermic peak (T₃) was caused by the hard‐segment crystal. The exothermic curves at an annealing temperature of above 150°C exhibited an exotherm caused by the T₃ microcrystalline growth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5174–5183, 2006     

Studies on thermoplastic polyurethanes based on new diphenylethane‐derivative diols. III. The effect of molecular weight and structure of soft segment on some properties of segmented polyurethanes

Two series of poly(ether urethane)s and one series of poly(ester urethane)s were synthesized, containing, respectively, poly(oxytetramethylene) diol (PTMO) of M _n = 1000 and 2000 and poly(ε‐caprolactone) diol of M _n = 2000 as soft segments. In each series the same hard segment, i.e., 4,4′‐(ethane‐1,2‐diyl)bis(benzenethiohexanol)/hexane‐1,6‐diyl diisocyanate, with different content (～ 14–72 wt %) was used. The polymers were prepared by a one‐step melt polymerization in the presence of dibutyltin dilaurate as a catalyst, at the molar ratio of NCO/OH = 1 (in the case of the polymers from PTMO of M _n = 1000 also at 1.05). For all polymers structures (by FTIR and X‐ray diffraction analysis) and physicochemical, thermal (by differential scanning calorimetry and thermogravimetric analysis), and tensile properties as well as Shore A/D hardness were determined. The resulting polymers were thermoplastic materials with partially crystalline structures (except the polymer with the highest content of PTMO of M _n = 2000). It was found that the poly(ether urethane)s showed lower crystallinity, glass‐transition temperature (T_g), and hardness as well as better thermal stability than the poly(ester urethane)s. Poly(ether urethane)s also exhibited higher tensile strength (up to 23.5 MPa vs. 20.3 MPa) and elongation at break (up to ～ 1950% vs. 1200%) in comparison with the corresponding poly(ester urethane)s. Among the poly(ether urethane)s an increase in soft‐segment length was accompanied by an increase in thermal stability, tensile strength, and elongation at break, as well as a decrease in T_g, crystallinity, and hardness. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Copolymers based on poly(butylene terephthalate) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone

A series of novel thermoplastic elastomers, based on poly(butylene terephthalate) (PBT) and polycaprolactone‐block‐polydimethylsiloxane‐block‐polycaprolactone (PCL‐PDMS‐PCL), with various mass fractions, were synthesized through melt polycondensation. In the synthesis of the poly(ester‐siloxane)s, the PCL blocks served as a compatibilizer for the non‐polar PDMS blocks and the polar comonomers dimethyl terephthalate and 1,4‐butanediol. The introduction of PCL‐PDMS‐PCL soft segments resulted in an improvement of the miscibility of the reaction mixture and therefore in higher molecular weight polymers. The content of hard PBT segments in the polymer chains was varied from 10 to 80 mass%. The degree of crystallinity of the poly(ester‐siloxane)s was determined using differential scanning calorimetry and wide‐angle X‐ray scattering. The introduction of PCL‐PDMS‐PCL soft segments into the polymer main chains reduced the crystallinity of the hard segments and altered related properties such as melting temperature and storage modulus, and also modified the surface properties. The thermal stability of the poly(ester‐siloxane)s was higher than that of the PBT homopolymer. The inclusion of the siloxane prepolymer with terminal PCL into the macromolecular chains increased the molecular weight of the copolymers, the homogeneity of the samples in terms of composition and structure and the thermal stability. It also resulted in mechanical properties which could be tailored. Copyright © 2010 Society of Chemical Industry     

Effects of reaction and cure temperatures on morphology and properties of poly(ester‐urethane)

Poly(ester‐urethane) was synthesized from poly(ethylene glycol adipate) (PEG) and 2,4‐toluene diisocyanate (TDI) to study the effects of reaction temperature and cure temperature on the crystallization behavior, morphology, and mechanical properties of the semicrystalline polyurethane (PU). PEG as soft segment was first reacted with TDI as hard segment at 90, 100, and 110°C, respectively, to obtain three kinds of PU prepolymers, coded as PEPU‐90, PEPU‐100, and PEPU‐110. Then the PU prepolymers were crosslinked by 1,1,1‐tris (hydroxylmethyl) propane (TMP) and were cured at 18, 25, 40, 60, and 80°C. Their structure and properties were characterized by attenuated total reflection Fourier transform infrared, wide‐angle X‐ray diffraction, scanning electron microscopy, dynamic mechanical analysis, and tensile testing. With an increase of the reaction temperature from 90 to 100°C, the crystallinity degree of soft segment decreased, but interaction between soft and hard segments enhanced, leading to the increase of the glass transition temperature (T_g) of soft domain and tensile strength. When the cure temperature was above 60°C, miscibility between soft and hard segments of the PEPU films was improved, resulting in relatively low crystallinity and elongation at break, but high soft segment T_g and tensile strength. On the whole, all of the PEPU‐90, PEPU‐100, and PEPU‐110 films cured above 60°C possessed higher tensile strength and elongation at break than that of the films cured at other temperatures. The results revealed that the reaction temperature and cure temperature play an important role in the improvement of the crosslinking structure and mechanical properties of the semicrystalline PU. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 708–714, 2006     

Effects of ion group content and polyol molecular weight on physical properties of HTPB‐based waterborne poly(urethane‐urea)s

A series of waterborne poly(urethane‐urea)s, WPUUs, based on using nonpolar hydroxyl‐terminated polybutadiene (HTPB) as the soft segment, were successfully synthesized in this article. The effects of the COOH group content and soft‐segment molecular weight (Mn_s) on the dispersion, morphology, and physical properties were investigated. Variations of the particle size, viscosity, and zeta potential were first governed by the hydrophilicity of the polymer chain, and then by the swelling derived from water. Fourier transfer infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) indicated that the degree of phase separation decreased as the COOH group content increased or as Mn_s decreased. However, the hydrogen bonding between the soft and hard segments and the two‐phase mixing could not occur in this nonpolar HTPB‐based WPUU system, indicating that the hard segments tended to form smaller domains and to pack more loosely. It was attributed to the fact that the presence of bulky ionic salt groups destroyed the ordered arrangement of the hard segments. In this case, the increases of the interface area between the soft and hard phases resulted in that the present behaviors were similar to the phase mixing. In tensile properties, HTPB‐based WPUUs exhibited higher tensile stress, elongation at break, and modulus as the COOH group content decreased or as Mn_s decreased. In thermal degradation, the introduction of HTPB polyol improved the thermal stability of WPUU. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Crystallization behaviour of random block copolymers of poly(butylene terephthalate) and poly(tetramethylene ether glycol)

The morphology and crystallization behaviour of random block copolymers of poly(butylene terephthalate) and poly(tetramethylene ether glycol) have been investigated. Single crystals have been grown in thin films crystallized from the melt. Well defined lamellae, exhibiting (hkO) single crystal electron diffraction patterns have been observed in copolymers containing down to 49 wt% (0.83 mole fraction) poly(butylene terephthalate). WAXS and electron diffraction support a model of a relatively pure poly(butylene terephthalate) crystal core with the poly(tetramethylene ether glycol) (soft segment) sequences and short hard segments being rejected to the lamellar surface and the soft segment rich matrix. The lateral dimensions of the lamellae are determined by the number of hard segment sequences long enough to traverse the stable crystal size at the crystallization temperature. This leads to an initial population of crystals formed at T_c and a second set of smaller crystals that grow from the short hard segment sequences upon cooling to room temperature. The result is fractionation by sequence length due to a coupling of the sequence distribution with the stable crystal size at the crystallization temperature.     

Polyether‐amide segmented copolymers based on ethylene terephthalamide units of uniform length

Segmented copolymers were synthesized using the crystallizable bisesterdiamide segment (N,N′‐bis(p‐carbomethoxybenzoyl)ethanediamine) T2T‐dimethyl (a one‐and‐a‐half repeating unit of nylon 2,T) and poly(tetramethyleneoxide) segments. Poly(tetramethyleneoxide) (PTMO) is amorphous and has a low T_g. The segment length was varied from 650 to 2800 g/mol by extending PTMO₆₅₀ using dimethyl isophthalate. The polymers were synthesized in the melt, and test samples were prepared by injection molding. The melting behavior, as well as the torsion modulus spectrum as a function of temperature, were studied using DSC and DMA, respectively. The T2T‐PTMO polymers were found to have sharp glass (T_g) and flow transitions (T_fl), and the modulus at the rubbery plateau appeared to be virtually temperature independent. The T_g value was found to be independent of the diamide concentration, thus indicating that the T2T segments were fully crystallized. The T_fl was found to decrease with increasing soft segment length; this was ascribed to a “solvent” effect of the amorphous phase of the crystalline T2T units. The difference between the melting and crystallization temperatures was found to be low, thus suggesting that on cooling, there is a high rate of crystallization. When ethanediol was added as a T2T segment extender, amide‐ester‐amide segments were introduced. These amide‐ester‐amide segments form a separate lamellar phase with a much higher melting temperature (>300°C). It was found that the crystallization rate of the T2T units was enhanced by the presence of the amide‐ester‐amide segments, indicating that upon cooling, the crystallized amide‐ester‐amide segments form the nucleation sites for the nonextended T2T segments. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1173–1180, 2001     

Synthesis and characterization of a poly(ether–ester) copolymer from poly(2,6 dimethyl‐1,4‐phenylene oxide) and poly(ethylene terephthalate)

A series of poly(ether–ester) copolymers were synthesized from poly(2,6 dimethyl‐1,4‐phenylene oxide) (PPO) and poly(ethylene terephthalate) (PET). The synthesis was carried out by two‐step solution polymerization process. PET oligomers were synthesized via glycolysis and subsequently used in the copolymerization reaction. FTIR spectroscopy analysis shows the coexistence of spectral contributions of PPO and PET on the spectra of their ether–ester copolymers. The composition of the poly(ether–ester)s was calculated via ¹H NMR spectroscopy. A single glass transition temperature was detected for all synthesized poly(ether–ester)s. T_g behavior as a function of poly(ether–ester) composition is well represented by the Gordon‐Taylor equation. The molar masses of the copolymers synthesized were calculated by viscosimetry. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

The effect of the mass ratio of hard and soft segments on some properties of thermoplastic poly(ester‐siloxane)s

A series of thermoplastic elastomers based on soft polydimethylsiloxane (PDMS) and hard poly(butylene terephthalate) (PBT) segments was synthesized using a two‐step transesterification reaction in the melt. The molar mass of the soft PDMS component was constant (M?_nPDMS = 1056 g mol^?1) while the starting reaction mixture compositions were varied to obtained copolymers with a mass ratio of hard to soft segments in the range from 70/30 to 40/60. The structure and composition of the copolymers was verified by ¹H NMR spectroscopy. It appeared that there was a pronounced molar mass maximum when the PBT content of the copolymers was approximately 60 mass%, whereas all samples were considerably inhomogeneous with respect to the distribution of the lengths of the hard segments. Differential scanning calorimetry (DSC) thermograms showed that the melting and crystallization temperature increased with increasing PBT content, as did the total degree of crystallinity, which was confirmed by wide‐angle X‐ray scattering (WAXS) analysis. Thermogravimetric analysis (TGA) performed in nitrogen gave subtle differences for samples of different composition, including that of the PBT homopolymer, whereas in oxygen these differences were more pronounced in the way the thermo‐oxidative stability of the obtained copolymers decreased with decreasing PBT content. Finally, it was shown that the hardness depended directly on the PBT content, ie the higher the PBT content, the greater the hardness of the corresponding copolymer. Copyright © 2004 Society of Chemical Industry     

Novel poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers through atom transfer radical polymerization

Poly(methyl methacrylate)‐block‐polyurethane‐block‐poly(methyl methacrylate) tri‐block copolymers have been synthesized successfully through atom transfer radical polymerization of methyl methacrylate using telechelic bromo‐terminated polyurethane/CuBr/N,N,N,N″,N″‐pentamethyldiethylenetriamine initiating system. As the time increases, the number‐average molecular weight increases linearly from 6400 to 37,000. This shows that the poly methyl methacrylate blocks were attached to polyurethane block. As the polymerization time increases, both conversion and molecular weight increased and the molecular weight increases linearly with increasing conversion. These results indicate that the formation of the tri‐block copolymers was through atom transfer radical polymerization mechanism. Proton nuclear magnetic resonance spectral results of the triblock copolymers show that the molar ratio between polyurethane and poly (methyl methacrylate) blocks is in the range of 1 : 16.3 to 1 : 449.4. Differential scanning calorimetry results show T_g of the soft segment at ?35°C and T_g of the hard segment at 75°C. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis of poly(1‐hexene)s end‐functionalized with phenols

Electrophilic alkylations of phenol/2,6‐dimethylphenol were performed with vinylidene‐terminated poly(1‐hexene)s using BF₃·OEt₂ catalyst. Vinylidene‐terminated poly(1‐hexene)s with M_n varying from 400 to 10000 were prepared by bulk polymerization of 1‐hexene at 50 to ?20 °C using Cp₂ZrCl₂/MAO catalysts. The phenol/2,6‐dimethylphenol‐terminated poly(1‐hexene)s was characterized by NMR (¹H, ¹³C), UV, IR and vapor phase osmometer (VPO). The isomer distribution (ortho, para and ortho/para) was determined by ¹³P NMR using a phosphitylating reagent, namely 2‐chloro‐1,3,2‐dioxaphospholane. The number‐average degree of functionality (F_n) >0.9 with >95% para selectivity could be achieved using low‐molecular‐weight oligomers of poly(1‐hexene)s. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of novel urethane‐siloxane copolymers with a high content of PCL‐PDMS‐PCL segments

Novel polyurethane copolymers derived from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BD) and α,ω‐dihydroxy‐[poly(caprolactone)‐poly (dimethylsiloxane)‐poly(caprolactone)] (α,ω‐dihydroxy‐(PCL‐PDMS‐PCL); = 6100 g mol^?1) were synthesized by a two‐step polyaddition reaction in solution. In the synthesis of the polyurethanes, the PCL blocks served as a compatibilizer between the nonpolar PDMS blocks and the polar comonomers, MDI and BD. The synthesis of thermoplastic polyurethanes (TPU) with high soft segment contents was optimized in terms of the concentrations of the reactants, the molar ratio of the NCO/OH groups, and the time and temperature of the polyaddition reaction. The structure, composition, and hard MDI/BD segment length of the synthesized polyurethane copolymers were determined by ¹H, ¹³C‐NMR, and two‐dimensional correlation (COSY, HSQC, and HMBC) spectroscopy, while the hydrogen bonding interactions in the copolymers were analyzed by FT‐IR spectroscopy. The influence of the reaction conditions on the structure, molecular weight, thermal, and some physical properties was studied at constant composition of the reaction mixture. A change in the molar ratio of the NCO/OH groups and the reaction conditions modified not only the molecular weight of the synthesized polyurethanes, but also the microstructure and therefore the thermal and physical properties of the copolymers. It was demonstrated that only PCL segments with high soft segment contents crystallize, thereby showing spherulitic morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011