Structure and electrochemical properties of La, F dual-doped LiLa0.01Mn1.99O3.99F0.01 cathode materials

The cathode materials LiMn2O4 and rare earth elements La-doped or La and F dual-doped spinel lithium manganese oxides were synthesized by the citric acid-assisted sol-gel method. The synthesized samples were investigated by differential thermal analysis (DTA) and thermogravimetry (TG) measurements, X-ray diffraction (XRD), scanning electronic microscope (SEM), cyclic voltammetry (CV), and charge-discharge test. XRD data shows that all the samples exhibit the same pure spinel phase, and the LiLa0.01Mn1.99O3.99F0.01 and LiLa0.01Mn1.99O4 samples have smaller lattice parameters and unit cell volume than LiMn2O4. SEM indicates that LiLa0.01Mn1.99O3.99F0.01 has a slightly smaller particle size and a more regular morphology structure with narrow size distribution. The charge-discharge test reveals that the initial capacities of LiMn2O4, LiLa0.01Mn1.99O4, and LiLa0.01Mn1.99O3.99F0.01 are 129.9, 122.8, and 126.4 mAh·g-1, and the capacity losses of the initial values after 50 cycles are 14.5%, 7.6%, and 8.0%, respectively. The CVs show that the La and F dual-doped spinel displays a better reversibility than LiMn2O4.     

球形LiMn1.5Ni0.5O4材料的嵌脱动力学

为明晰Li Mn1.5Ni0.5O4正极材料的动力学性能,采用水热辅助共沉淀法合成了尖晶石Li Mn1.5Ni0.5O4正极材料,并采用扫描电镜(SEM)、X射线粉末衍射(XRD)和电化学阻抗(EIS)研究了材料的结构和锂离子嵌脱动力学.实验结果表明:共沉淀法制备的Li Ni0.5Mn1.5O4材料颗粒呈均匀球形,且平均粒径较小,粒度分布较窄.在循环过程中,Li Ni0.5Mn1.5O4的电荷转移电阻增大,锂离子扩散系数减小,进而电子电导率和离子电导率下降.温度升高后,Li Ni0.5Mn1.5O4材料的溶液电阻变化不大,但是电荷转移电阻逐渐增大,锂离子扩散系数逐渐减小;此外,随着温度的升高,Li Ni0.5Mn1.5O4材料的溶解速度加快,从而导致SEI膜的厚度增大.Li Ni0.5Mn1.5O4材料的嵌脱锂动力学与温度和循环次数有密切关系.     

Characteristics of LiCoO2, LiMn2O4 and LiNi0.45Co0.1Mn0.45O2 as cathodes of lithium ion batteries

LiNi_0.45Co_0.10Mn_0.45O₂ was synthesized from Li₂CO₃ and a triple oxide of nickel, cobalt and manganese at 950 °C in air. The structures and characteristics of LiNi_0.45Co_0.10Mn_0.45O₂, LiCoO₂ and LiMn₂O₄ were investigated by XRD, SEM and electrochemical measurements. The results show that LiNi_0.45Co_0.10Mn_0.45O₂ has a layered structure with hexagonal lattice. The commercial LiCoO₂ has sphere-like appearance and smooth surfaces, while the LiMn₂O₄ and LiNi_0.45Co_0.10Mn_0.45O₂ consist of cornered and uneven particles. LiNi_0.45Co_0.10Mn_0.45O₂ has a large discharge capacity of 140.9 mA · h/g in practical lithium ion battery, which is 33.4% and 2.8% above that of LiMn₂O₄ and LiCoO₂, respectively. LiCoO₂ and LiMn₂O₄ have higher discharge voltage and better rate-capability than LiNi_0.45Co_0.10Mn_0.45O₂. All the three cathodes have excellent cycling performance with capacity retention of above 89.3% at the 250th cycle. Batteries with LiMn₂O₄ or LiNi_0.45Co_0.10Mn_0.45O₂ cathodes show better safety performance under abusive conditions than those with LiCoO₂ cathodes. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China; Project(2005037698) supported by the Postdoctoral Science Foundation of China     

Influence on performance and structure of spinel LiMn2O4 for lithium-ion batteries by doping rare-earth Sm

The spinel LiMn₂O₄ used as cathode materials for lithium-ion batteries was synthesized by mechano-chemistry fluid activation process, and modified by doping rare-earth Sm. Thesting of X-ray diffraction, cyclic voltammograms, charge-discharge and SEM was carried out for LiMn₂O₄ cathode materials and the modified materials. The results show that the cathode materials doped rare earth Li _x Mn_2−y Sm _z O₄ (0.95⩽x⩽1.2, 0⩽y⩽0.3, 0⩽z⩽0.2) exhibit standard spinel structure, high reversibility of electrochemistry and excellent properties of charge-discharge. In EC: DMC(1 : 1)+1 mol/L LiPF₆ electrolyte with discharge capacity more than 130 mA · h/g, and its capacity is deteriorated less than 15% after 300 cycles at room temperature and less than 20% after 200 cycles at 55°C. At the same time, Crystal Field Theory was applied to explain the function and mechanism of doped rare earth element. Foundation item: Project (02JJY2081) supported by the Natural Science Foundation of Hunan Province     

Modification of LiCo1/3Ni1/3Mn1/3O2 cathode material by CeO2-coating

LiCo_1/3Ni_1/3Mn_1/3O₂ was coated by a layer of 1.0 wt% CeO₂ via sol-gel method. The bared and coated LiMn_1/3Co_1/3Ni_1/3O₂ was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), cyclic voltammogram (CV) and galvanotactic charge-discharge test. The results show that the coating layer has no effect on the crystal structure, only coating on the surface; the 1.0 wt% CeO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ exhibits better discharge capacity and cycling performance than the bared LiCo_1/3Ni_1/3Mn_1/3O₂. The discharge capacity of 1.0 wt% CeO₂-coated cathode is 182.5 mAh·g⁻¹ at a current density of 20 mA·g⁻¹, in contrast to 165.8 mAh·g⁻¹of the bared sample. The discharge capacity retention of 1.0 wt% CeO₂-coated sample after 12 cycles reaches 93.2%, in comparison with 86.6% of the bared sample. CV results show that the CeO₂ coating could suppress phase transitions and prevent the surface of cathode material from direct contact with the electrolyte, thus enhance the electrochemical performance of the coated material.     

Synthesis and characterization of high-voltage cathode material LiNi0.5Mn1.5O4 by one-step solid-state reaction

LiNi_0.5Mn_1.5O₄ was prepared under various conditions by one-step solid-state reaction in air and its properties were investigated by X-ray diffractormetry (XRD), scanning electron microscopy (SEM) and electrochemical measurement. XRD patterns show that LiNi_0.5Mn_1.5O₄ synthesized under various conditions has cubic spinel structure. SEM images exhibit that the particle size increases with increasing calcination temperature and time. Electrochemical test shows that the LiNi_0.5Mn_1.5O₄ calcined at 700 °C for 24 h delivers up to 143 mA · h/g, and the capacity retains 132 mA · h/g after 30 cycles. Foundation item: Project (76600) supported by Postdoctoral Science Foundation of Central South University     

Kinetic study of LiMn2O4 in process of lithium intercalation

Exchange current density of spinel LiMn₂O₄ was studied by linear polarization. The relationship of the kinetic property with the structure of spinel LiMn₂O₄ was investigated by studying the effect of the doping and surface coating on the kinetic properties of electrode material. The results show that the exchange current density of spinel LiMn₂O₄ electrode increases with the increase of the amount for lithium intercalation at first, and then decreases. The maximal exchange current density appeares at the 80%–90% lithium intercalation. The similar phenomenon was observed on the doped spinel LiMn₂O₄ electrode. Doping can enhance the exchange current density of spinel LiMn₂O₄ material. However, the degree of the doping effect varies with the doped element varying. Surface coating can also enhance the exchange current density of spinel material, and the increment of value is higher than that of doped ones. Foundation item: Project(50302016) supported by the National Natural Science Foundation of China     

Overcharge performance of LiMn2O4/graphite battery with large capacity

The LiMn₂O₄/graphite battery was fabricated and its 3 C/10 V overcharge performance was studied. Spinel LiMn₂O₄ was synthesized by solid-state method and 325680-type size full battery was fabricated. The structure and morphology of the powders were characterized by XRD and SEM technique, respectively. The battery explodes after 3 C/10 V overcharged test, and surface temperature of the battery case arrives at 290 °C in 12 s after exploding. Black air is given out with blast. Carbon, MnO, and Li₂CO₃ are observed in the exploded powders. The cathode electrode remains spinel structure with 5.0 V charged. Cracks in the cathode electrode particles are detected with the increase of voltage by SEM technique. The 5.0 V charged electrode can decompose into Mn₃O₄ at 400 °C. It is demonstrated that the decomposition of 5.0 V charged electrode can be promoted and Mn⁴⁺ can be deoxidized to Mn²⁺ by carbon and electrolyte through the simulation of blast process.     

The Mechanism of Sol-Gel Synthesis of Normal Spinel LiMn2O4 with Chelation of Citric Acid

The sol-gel process of citric acid chelating with metal cations for the synthesis of normol spinel LiMn2O4 and the reaction mechanion mechavism were investigated by means of XRD,TG-DTA,and SEM ,the results show that at the beginning lithium citrate and chelate compound of citic acid with manganese ions formed ,and then with heating the esterification and condensation reacions occured between them and glyol ,The products obtained are polymers in which metal cations are distibuted homogeneously on atomic scale that ensur hight reacivity to cations of Li^ and Mn^2 ,Firing the gel grepared by this process ,the lattice diffusions of solid reactant ions caused by non-homogeneity of reactants are elinimated and avoided .At 400℃ phase-pure LiMn2O4 with nanometer scale crystallization having precise stoichiometry and perfect crystallization can be obtained ,The model of chelate coordinated of double -molecule between citric acid and Mn^2 in the gel network is proosed ,It is important for explaining the dispersion state of Mn^2 and the formaiton process of gel by this model.     

Sol—Gel Synthesis of Normal Spinel LiMn2O4 and Its Characteristics

Normal spinel LiMn2O4 was synthesized by sol-gel method using lithium nitrate,manganese nitrate,citric acid and ethylene glycol as raw materials.LiMn2O4 was characterized by XRD,TG-DTA,IR,SEMand AAS,The optimum conditions for the synthesis were explored.Citric and ethylene glycol were mixed with molar ratio of 0.25,and the mixtrue was esterified at 140℃ for 4 hours.Then lithium nitrate and manganese nitrate were added with molar ratio of 0.6,In the system,the total molar of cations was equal to that of citric acid.At last,reflux the system at 105℃ for 2 hours,Dried gel was fired at 600℃ for 8 hours.Particle diameters of raw product were about 100nm mainly.Further research shows that lithium ion of LiMn2O4 is easy to be extracted,and normal spinel λ-MnO2 can be obtained after lithium ion extraction.     

Synthesis and characterization of Mg3(PO4)2-coated Li1.05Ni1/3Mn1/3Co1/3O2 cathode material for Li-ion battery

Mg₃(PO₄)₂-coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode materials were synthesized via co-precipitation method. The morphology, structure, electrochemical performance and thermal stability were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), cyclic voltammetry(CV), electrochemical impedance spectroscopy(EIS), charge/discharge cycling and differential scanning calorimeter (DSC). SEM analysis shows that Mg₃(PO₄)₂-coating changes the morphologies of their particles and increases the grains size. XRD and CV results show that Mg₃(PO₄)₂-coating powder is homogeneous and has better layered structure than the bare one. Mg₃(PO₄)₂-coating improved high rate discharge capacity and cycle-life performance. The reason why the cycling performance of Mg₃(PO₄)₂-coated sample at 55 °C was better than that of room temperature was the increasing of lithium-ion diffusion rate and charge transfer rate with temperature rising. Mg₃(PO₄)₂-coating improved the cathode thermal stability, and the result was consistent with thermal abuse tests using Li-ion cells: the Mg₃(PO₄)₂ coated Li_1.05Ni_1/3Mn_1/3Co_1/3O₂ cathode did not exhibit thermal runaway with smoke and explosion, in contrast to the cells containing the bare Li_1.05Ni_1/3Mn_1/3Co_1/3O₂. Funded by the National Natural Science Foundation of China (No. 20273047)     

Synthesis and Characterization of LiCoxMn2-xO4 Cathode Materials

LiCoxMn2.04 cathode materials for lithium ion batteries were synthesized by mechanical activation-solid state reaction at 750 ℃ for 24 h in air atmosphere, and their crystal structure, morphology, element composition and electrochemical performance were characterized with XRD, SEM, ICP-AES and charge-discharge test. The experimental results show that all samples have a single spinel structure, well formed crystal shape and uniformly particle size distribution. The lattice parameters of LiCo Mn2-xO4 decrease and the average oxidation states of manganese ions increase with an increase in Co content. Compared with pure LiMn2O4, the LiCo Mn2xO4 （x=0.03-0.12） samples show a lower special capacity, but their cycling life are improved. The capacity loss of LiCo009Mn191O4 and LiCo0.1Mn1.88O4 is only 1.85% and 0.95%, respectively, after the 20th cycle. The improvement of the cycle performance is attributed to the substitution of Co at the Mn sites in the spinel structure, which suppresses the Jahn-Teller distortion and improves the structural stability.     

第一性原理研究:Mg2+掺杂尖晶石型LiMn2O4的电子结构

尖晶石 LiMn₂O₄ 正极材料是在原有锂电池正极材料 LiCoO₂ 、LiNiO₂ 、LiMnO₂ 的基础上研发出来的优选 正极材料, 它相较于 LiCoO₂ 材料价格更加低廉热稳定性加强且安全性能有所提高。采用 Mg²⁺ 掺杂 LiMn₂O₄正极 材料, 利用基于密度泛函理论的第一性原理对 LiMg_0.5Mn_1.5O₄ 晶格常数与能带结构、态密度进行计算与分析。结 果表明: 新材料 LiMg_0.5Mn_1.5O₄ 的空间群为 F4332, 掺杂后晶胞参数 a 明显减小, 晶胞体积收缩; 掺杂量为 0.5 时明 显比掺杂量 0.125 时 Fermi 能量和能量密度高。Mg ²⁺ 掺杂能影响 LiMn₂O₄ 的晶体结构, 形成更加稳定的共价键。 掺杂量会改变 LiMn₂O₄ 的空间群影响到结构稳定性, 所以掺杂量不宜过大。     

Al2O3 coating for improving thermal stability performance of manganese spinel battery

The synthesis of Al₂O₃-coated and uncoated LiMn₂O₄ by solid-state method and fabrication of LiMn₂O₄/graphite battery were described. The structure and morphology of the powders were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The electrochemical and overcharge performances of Al₂O₃-coated and uncoated LiMn₂O₄ batteries were investigated and compared. The uncoated LiMn₂O₄ battery shows capacity loss of 16.5% after 200 cycles, and the coated LiMn₂O₄ battery only shows 12.5% after 200 cycles. The uncoated LiMn₂O₄ battery explodes and creates carbon, MnO, and Li₂CO₃ after 3C/10 V overcharged test, while the coated LiMn₂O₄ battery passes the test. The steadier structure, polarization of electrode and modified layer are responsible for the safety performance.     

First-principle investigation on stability of Co-doped spinel λ-Mn4-xCoxO8

The mechanism of stability of Co-doped spinel λ-MnO2 that is referred to as spinel LixMn2O4 （x=0） was studied by using the first-principle calculation method. The total energy and formation enthalpy can be decreased remarkably due to the Co substation, resulting in a more stable structure ofλ-MnxCr2-xO4. The bond order and DOS analysis were given in detail to explain the nature of stability improvement. The calculated results show that as the content of Co dopant increases, the bond order of Mn-O becomes larger and the peak of density of states around Fermi level shifts toward lower energy. The charge density distribution illustrates that the Mn-O bonding is ionic and partially covalent, and the covalent Mn-O bonding becomes stronger with the increase of Co dopant content. The results confirm that the Co-doping will enhance the stability of λ-MnO2 and hence improve the electrochemistry performance of LixMn2O4.     

Theoretic Diffraction Research on the Order-Disorder Effect of Transition Metal in Li(Ni1/3Co1/3Mn1/3)O2

Li(Ni_1/3Co_1/3Mn_1/3)O₂的(3b)位有序-无序效应研究

曹春晖^1,2, 张建¹, 杨传铮¹, 夏保佳¹

（1.上海微系统与信息技术研究所,上海 200050;

2.中国科学院大学, 北京100049）

创新点说明：

提出了有序度的概念,通过理论模拟了过渡金属在3b位不同有序度下的衍射情况。

研究目的：

借助理论衍射研究镍钴锰在三元材料中的占位情况,为实际得到的衍射数据分析起指导作用。

研究方法和结果：

借助Powercell程序模拟不同结构下的衍射情况。结果表明：对于Li(Ni1/3Co1/3Mn1/3)O2,基体衍射线的强度不随有序度而变化,有序度增加时,超点阵衍射线强度增加,但是即使对于有序度最大时,超点阵线的相对强度只有0.225%和0.043%。

结论：

3b位的有序无序很难通过常规的衍射实验观测到,必须提高X射线源的强度才可能观测到。

关键词：Li(Ni1/3Co1/3Mn1/3)O2, 有序-无序,超结构,衍射

     

Preparation of LiFePO4 for lithium ion battery using Fe2P2O7 as precursor

In order to obtain a new precursor for LiFePO4, Fe2P2O7 with high purity was prepared through solid phase reaction at 650 ℃ using starting materials of FeC2O4 and NH4H2PO4 in an argon atmosphere. Using the as-prepared Fe2P2O7, Li2CO3 and glucose as raw materials, pure LiFePO4 and LiFePO4/C composite materials were respectively synthesized by solid state reaction at 700 ℃ in an argon atmosphere. X-ray diffractometry and scanning electron microscopy（SEM） were employed to characterize the as-prepared Fe2P2O7, LiFePO4 and LiFePO4/C. The as-prepared Fe2P2O7 crystallizes in the Cl space group and belongs to β-Fe2P2O7 for crystal phase. The particle size distribution of Fe2P2O7 observed by SEM is 0.4-3.0 μm. During the Li^＋ ion chemical intercalation, radical P2O7^4- is disrupted into two PO4^3- ions in the presence of O^2-, thus providing a feasible technique to dispose this poor dissolvable pyrophosphate. LiFePO4/C composite exhibits initial charge and discharge capacities of 154 and 132 mA·h/g, respectively.     

Luminescent properties of BaO-La2O3-B2O3 glasses with dopant

The luminescent properties of glasses synthesized in air atmosphere by conventional high temperature process were stud{ed. The emissions spectra of Eu^2 and Eu^3 were observed in BaO-La2O3-B2O3-Eu2O3 glasses.The results show that the broad emission peaks at 430 nm correspond to 5d→4f emission transition of Eu^2 , the sharp emission peaks at 592, 616, 650 and 250 nm correspond to 5^D0→1Fj(j=1--4) emission transition of Eu^3 ,respectively, which indicates that the BaO-La2O3a-B2O3-Eu2O3 glass can convert ultraviolet and green omponents of sunlight into blue and red light so as to increase the intensity of blue and red light, respectively. The luminescent in--tensity of Eu^2 increases with increasing the molar ratio of Tb^3 in BaO-La2O3-B2O3-Eu2O3a-Tb4O3 glasses, whereas the luminescent intensity of Eua^3 decreases. So the luminescent intensity of Eu(Ⅲ,Ⅱ) is influenced by Tb^3 .These phenomena can be explained by electron transfer mechanism; Eu^3 (4f6) Tb^3 (4f^8)→Eu^2 (4f′) Tb^4 (4f′). Taking advantage of the luminescent properties of BaO-La2O3-B2O3-Eu2O3 glasses, light-conversion glass for agriculture can be produced.     

Structure and electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>−<Emphasis Type="Italic">x</Emphasis>F<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

LiMn₂O₄−_xF_x prepared by the sol-gel method has a perfect crystal formation. The crystal particle size of the material was medium and distributed uniformly. The substitution of F for O increased the specific capacity of the material at the cost of the cycleability. The explanation of this results is that the F decreases the valence of Mn, that is, more Mn³⁺ and less Mn⁴⁺ exist in the material. The increase of Mn³⁺ will improve the initial specific capacity and Mn³⁺ is the original reason for Jahn-Teller effect that caused the poor cycleability of the cathode material by the micro-distortion of the crystal structure. In addition, the expanded measurement of the crystal lattice is also the reason for the poor cycleability. Therefore, the results of F-substitution and cation-substitution are opposite. If the two methods are combined, they can compensate the inability each other and the satisfactory results may be obtained. XIA Jun-lei: Born in 1977 Funded by the National Natural Science Foundation of China (No. 59972026)     

Structure and electrochemical properties of LiLaxMn2-xO4 cathode material by the ultrasonic-assisted sol-gel method

Powders of spinel LiLaxMn2_xO4 were successfully synthesized by the ultrasonic-assisted sol-gel (UASG) method.The structure and properties of LiLaxMn2_xO4 were examined by X-ray diffraction (XRD),Fourier transform infrared (FT-IR) spectros-copy,scanning electronic microscopy (SEM),galvanostatic charge-discharge test,and cyclic voltammetry (CV).XRD results showthat the La3+ can partially replace Mn3+ in the spinel and the doped materials with La3+ have a larger lattice constant compared with pristine LiMn2O4.FT-IR indicates that the absorption peak of Mn3+-O and Mn4+-O bonds has a red and blue shift with the increase of doping lanthanum in LiLaxMn2_xO4,respectively.The charge-discharge test exhibits that the initial discharge capacity of LiLaxMn2_xO4 drops off,and the capacity retention increases gradually at C/5 discharge rate with the increase of doping lanthanum,and LiLa0.01Mn1.99O4 has a higher discharge capacity and a better cycling performance at 1C discharge rate.CV reveals that the dop-ing La3+ is beneficial to the reversible extraction and intercalation of Li+ ions.