基于光纤光栅传感器的复合材料层合板冲击能量研究

复合材料结构较容易产生结构表面无法探测到的低速冲击损伤。试验利用光纤复合材料结构中布拉格光纤光栅传感器受到低速冲击后光栅中心波长随应力变化这一特性,在恒温下用布拉格光纤光栅传感器对复合材料智能结构受到的低速冲击能量给出判别,并对通过光纤光栅解调仪采集下来的低速冲击信号进行频谱分析。在计算冲击信号所有能量等级的频谱峰值后,给出可以界定能量等级的频谱峰值临界值,利用其来判别低速冲击能量等级。试验表明布拉格光纤光栅传感器可以监测复合材料受到冲击的信号,能够对复合材料结构低速冲击进行能量等级判断研究     

基于光纤光栅传感器的飞机油箱表面复合材料板振动研究

飞机机翼油箱在飞行时容易受到各种振源影响,而油箱结构中的复合材料较容易受低频振动影响。试验利用布拉格光纤光栅传感器受到激励后光栅中心波长随应力变化这一特性,在恒温下用布拉格光纤光栅传感器对飞机油箱表面变截面碳纤维层合板受到的振动信号进行研究,并对通过光纤光栅解调仪采集下来的振动动态信号进行频谱分析。在计算出动态信号的频谱峰值后,分析得出变截面碳纤维层合板的振动信号受到截面厚度、激励点位置的共同影响。结果表明利用光纤Bragg光栅传感网络对飞机油箱表面变截面碳纤维层合板受到的振动影响进行监测。     

基于FBG传感技术的复合材料T型加筋板低速冲击损伤监测

针对碳纤维增强树脂复合材料低速冲击损伤的实时监测,设计将布拉格光纤光栅（FBG）传感器埋植在复合材料T型加筋板结构的三角填充区,在线监测复合材料T型加筋板冲击损伤过程。分别将FBG传感器埋植于复合材料层合板内部和复合材料T型加筋板的三角填充区,对比FBG传感器的埋入对复合材料层合板和复合材料T型加筋板力学性能的影响。结果表明,内埋FBG传感器的复合材料层合板试样的拉伸强度比未埋植传感器的层合板试样降低了约5%,但在FBG传感器的破坏应变范围内,FBG传感器可以准确、实时地监测复合材料的应变信号。将FBG传感器埋入复合材料T型加筋板的三角填充区,内埋FBG传感器的T型加筋板样件压缩破坏载荷与未埋植的样件基本一致。通过对比T型加筋板蒙皮上冲击位置、冲击能量对FBG传感器测得的冲击过程持续时间和最大应变值的影响,表明冲击过程持续时间随着冲击能量增大而延长,最大应变值随着冲击距离的增加呈下降趋势,而最大应变值随着冲击能量的增大呈上升趋势。利用FBG传感器测得的应变信号可初步实现对复合材料T型加筋板蒙皮冲击损伤位置及冲击能量的实时监测。      

复合材料胶层光纤布格光栅应变监测优化配置研究

航空航天用复合材料粘接胶层在制造和服役过程中不可避免会产生各种缺陷和损伤。针对其粘接胶层缺陷和损伤检测,基于光纤光栅应变传感原理,提出一种针对复合材料胶接层结构应变监测的光纤光栅传感网络优化配置的方法。通过仿真和实验研究了埋入复合材料构件胶接层的光纤布拉格光栅传感器在静载作用下的敏感区域分布特性,分析了载荷位移与布拉格波长漂移的关系,建立符合光纤布拉格光栅传感器实际特点的探测模型,采用粒子群优化算法进行光纤光栅传感网络的优化布置,研究结果表明光纤布拉格光栅传感器位置经优化后,覆盖率得到明显提高。     

光纤布拉格光栅监测复合材料固化

复合材料层合板在固化成型过程中形成的残余应变和应力是影响材料质量的重要因素,它与预浸料铺层在固化工艺过程中产生的应变密切相关。在研究和测试了光纤布拉格光栅应变和温度传感器传感特性的基础上,将二者埋入复合材料预浸料铺层,在热压釜成型工艺过程中监测了材料内部的温度和应变发展历程,由此获得对称正交层合板的宏观残余应变。监测结果表明,单向和对称正交层合板在固化结束后都将产生收缩,对称正交层合板铺层内的残余应变平行于纤维方向为压应变,垂直于纤维方向为拉应变。光纤光栅传感器为复合材料固化监测及层合板残余应力分析提供了一种新的工具,为实现复合材料从制造到服役的全寿命、一体化监测提供了可能。      

变厚度复合材料板低速冲击能量监测

为了监测变厚度复合材料层合板在使用过程中受到的低速冲击载荷,将光纤传感及信号处理技术相结合,建立了光纤布拉格光栅冲击能量监测系统。将光纤传感网络采集到的所有冲击样本信号进行WEMD分解;根据样本信号冲击能量特征值建立冲击样本信号能量特征集合;根据信号分解的第一阶分量确定厚度系数并修正能量特征集合,评估实际冲击能量。结果表明,基于WEMD分解的厚度系数修正方法能够更准确评估低速冲击能量,其中低灵敏度的大厚度区域平均误差从15.19%明显减少为6.96%。提出的能量识别方法成功识别了1~3 J冲击能量,其中最大误差为15.67%,平均误差为5.5%。     

冰雹冲击复合材料层合板失效模式分析与数值模拟

针对复合材料层合板结构,建立了冰雹冲击复合材料层合板的有限元模型,在充分考虑冲击过程中冰雹的流体特性下,给出了冰雹和复合材料层合板的材料模型和损伤准则,利用显式有限元分析工具LS-DYNA研究了不同冰雹冲击速度下复合材料层合板的临界破坏速度和破坏形式。结果表明,文中给出的冰雹、复合材料层合板的材料模型和损伤准则能够合理地再现冰雹冲击复合材料板的过程;复合材料层合板(AS4/8552)在冰雹高速冲击下首先发生的是基体开裂,当冰雹速度到达125m/s时,层合板上表面纤维发生断裂,但在整个冰雹冲击过程中层合板没有发生压缩失效     

单根光纤光栅监测复合材料固化工艺过程多目标参量技术的研究

采用单根布拉格光纤光栅传感器实现了对复合材料工艺过程不同阶段、不同目标的监测。在成型阶段监测树脂的温度(粘度)发展历程；在施加成型压力时监测树脂内部压力的变化；在固化与降温阶段监测复合材料层板内部的应力变化。试验结果表明，利用-根布拉格光纤光栅传感器同时实现对复合材料固化工艺全过程的主要控制参量的监测是完全可行的。     

纤维复合材料层合板内埋光纤光栅传感器的保护技术

内埋的光纤Bragg光栅（FBG）传感器的存活率及测试精度是其在线监测纤维增强树脂基复合材料制备和服役状态的重要前提。采用[90₁₁/0₁₁]的碳纤维预浸料铺层方式,在层合板0°和45°方向的典型位置埋入FBG温度和应变传感器,采用模压成型工艺制备复合材料层合板。在异向铺排（光纤光栅方向与碳纤维方向不同）的45°方向光纤光栅传感器内埋于碳纤维预浸料层间的过程中,对其采用4种不同的保护方式。通过对比实验结果发现:当对异向铺排的FBG传感器不采取保护措施时,在加热加压复合材料时光纤光栅容易失活;整层铺设同向预浸料以保护异向铺排的FBG传感器的方式改变了具有特定铺层参数复合材料的力学性能;采用窄长条同向预浸料上下包埋保护FBG传感器的方式增大了应变光栅测量结果的系统误差;采用窄长条同向预浸料上下包埋并在邻近铺层开凹槽的保护方式能明显提高内埋光纤光栅的存活率及测试精度。      

基于多重信号分类算法的复合材料冲击定位

为了提高复合材料结构冲击定位的精度和实时性, 将阵列信号处理技术引入到结构健康监测领域, 提出了利用小波变换和多重信号分类算法实现复合材料结构冲击定位的新方法: 通过小波变换提取冲击响应信号某一窄带频率成分, 运用多重信号分类(MUSIC) 算法实现冲击源到达方向的估计; 根据Lamb 波传播特性, 用小波变换求出某一中心频率下的对称模式和反对称模式的Lamb 波到达同一传感器的时间差, 结合对称模式和反对称模式Lamb 的速度差就可以估计出冲击源到达传感器的距离, 实现冲击定位。对玻璃纤维/环氧树脂复合材料层合板和碳纤维/双马树脂基复合材料层合板2 种试件的实验均表明该方法能快速、精确地识别出冲击源位置。      

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...