微悬浮聚合法合成聚醋酸乙烯酯的动力学研究

采用微悬浮法合成聚醋酸乙烯酯,对其聚合反应的动力学进行了研究。考察了引发剂浓度、乳化剂浓度、单体浓度以及温度对聚合反应速率的影响。结果表明,聚合反应速率对引发剂浓度、乳化剂浓度和单体浓度的反应级数分别为0．45,0．28,1．90,单体浓度对聚合反应速率的影响最大,反应体系的表观活化能为105．96 kJ/mol。     

Kinetic study of the aqueous free‐radical polymerization of 2‐acrylamido‐2‐methyl‐1‐propanesulfonic acid via an online proton nuclear magnetic resonance technique

The free‐radical polymerization of 2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid (AMPS) in aqueous media and in the presence of potassium persulfate (KPS) as a thermal initiator was studied. The ¹H‐NMR method was applied to record the reaction data in online gain. The effects of the monomer and initiator concentrations and also the reaction temperature were studied. The order of reaction with respect to the monomer was much greater than unity (1.94). None of the three theories describing an order of reaction higher than unity could predict the AMPS polymerization mechanism in this study. So, a new mechanism is presented. It is suggested that initiation took place through the formation of a complex between the initiator and monomer, and termination occurred not only by a bimolecular reaction but also by a monomolecular reaction. The order with respect to KPS was 0.49; this was consistent with classical kinetic theory. The determined activation energy at the overall rate of reaction was 92.7 kJ mol^?1 K^?1. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Properties and behavior of CTBN‐modified epoxy with IPN structure

CTBN‐modified epoxy resins (CMEs) with an interpenetrating‐network (IPN) structure and a nanometer‐sized morphology were prepared. Two systems of CMEs, called CNE/DDS/I‐CTBN‐B and CNE/DDS/I‐CTBN‐D, with IPN structures, were synthesized by heat‐curing a homogeneous resin, CNE/DDS/CTBN/2‐MI, obtained by mixing a carboxyl‐terminated butadiene–acrylonitrile liquid rubber (CTBN) with a solution of polyglycidyl ether of o‐cresol‐formaldehyde novolac (CNE), 4,4′‐diamino diphenyl sulfone (DDS), and 2‐methyl imidazole (2‐MI), in the presence of benzoyl peroxide and dicumyl peroxide, respectively. The IPN morphologies of the two systems of CMEs were identified by small‐angle X‐ray scattering by measuring the value of the specific interfacial surface area S_sp between the cured CNE/DDS matrix and the vulcanized CTBN. Properties such as fracture toughness, internal stress, and thermal and dynamic mechanical properties of these IPN‐structured CMEs were studied in detail, and were compared with those of a conventional CME, CNE/DDS/CTBN, obtained by dispersing CTBN particles in a crosslinked CNE/DDS matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Novel Reaction Kinetic Model for Anionic Polyamide‐6

Semi‐adiabatic temperature measurements are recorded and used to define semi‐empirical equations for the simulation and prediction of the anionic polyamide‐6 (APA‐6) reaction kinetics. The resin mixture used has a long infusion window before the reaction starts. The prediction of the induction time and its corresponding initial temperature of reaction is explored. By means of this semi‐empirical approach and an optimised fitting procedure, the reaction kinetics of APA‐6 can successfully be described. The adiabatic polymerisation can be predicted on the basis of an autocatalytic Kamal‐Sourour model for thermoset resins, and the crystallisation can be described using the isothermal crystallisation model.

     

Kinetic of epoxy resin formation by high‐performance liquid chromatography

This article is focused on the following of the cure of an epoxy resin by high‐performance liquid chromatography (HPLC) and the comparison of the data obtained with those obtained by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) techniques usually employed for characterize curing processes. A reversed‐phase HPLC method with UV detection is developed to study the kinetic of the curing reaction of diglycidyl ether of bisphenol A (DGEBA) with 1,3‐cyclohexanebismethylamine (1,3‐BAC) at 60, 70, and 80°C, before and after gelation. The limits of quantification obtained permit the application of the proposed method until the last steps of the formation kinetic. HPLC and DSC analysis show a good correlation. The gel conversions obtained by HPLC and DMA agree well. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 497–504, 2003     

Synthesis and characteristics of an amphoteric semi‐IPN hydrogel composed of acrylic acid and poly(diallydimethylammonium chloride)

Semi‐interpenetrating polymer network (IPN) hydrogels, with acrylic acid (AA) and poly(diallydimethylammonium chloride) (PDMDAAC), were constructed by a sequential IPN method. The characterizations of the IPN hydrogels were investigated by FTIR, DTA, and swelling tests under various conditions. The prepared semi‐IPN hydrogels exhibited relatively high swelling capacity, in the range of 477–630 g/g at 25°C. The results show that the swelling capacity of AA/PDMDAAC semi‐IPN hydrogels was pH and temperature dependent. Swelling behaviors were also studied in the different salt solutions. Swelling kinetic parameters are given. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 345–350, 2007     

Kinetic study of the thermal decomposition of (2‐phenyl‐1,3‐dioxolane‐4‐yl) methyl methacrylate and 2‐hydroxyethyl methacrylate copolymers

The kinetics of nonisothermal decomposition of (2‐phenyl‐1,3‐dioxolane‐4‐yl) methyl methacrylate (PDMMA), 2‐hydroxyethyl methacrylate (HEMA), and vinyl‐pyrrolidone (VPy) copolymers were investigated by thermogravimetry (TG) and differential thermal analysis (DTA). The data indicated that the major weight loss occurs in the range of 270 to 450°C. The decomposition characteristics showed essentially two regimes and varied depending on the temperature and the copolymer composition. The apparent kinetic parameters of the decompositions were estimated from both TG and DTA data by using the alternative calculation methods. The results suggest that the weight loss rates may be represented, depending on the type of sample, by a reaction model of overall order 1.0 to 1.6, with an activation energy of approximately 65–95 kJ mol^?1. The DTA data estimated considerably higher values for the overall activation energies, around 198–240 kJ mol^?1. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1500–1508, 2005     

Kinetic study of the polymerization of dimethyldiallylammonium chloride and acrylamide

The kinetics of the polymerization of dimethyldiallylammonium chloride (DMDAAC) and acrylamide (AM) with different monomer molar ratios initiated by an ammonium persulfate–sodium bisulfate redox complex in an aqueous solution were studied. The polymerization rate (R_p) equation, the activation energy (E_a), and the reactivity ratio were measured. The results show that when the n_DMDAAC:n_AM values were 1 : 9, 2 : 8, 3 : 7, 4 : 6, and 5 : 5, the copolymerization rate equation were R_p1 = k[M]^2.61[I_O]^0.51[I_R]^0.52, R_p2 = k[M]^2.70[I_O]^0.50[I_R]^0.53, R_p3 = k[M]^2.73[I_O]^0.50[I_R]^0.56, R_p4 = k[M]^2.77[I_O]^0.51[I_R]^0.59, and R_p5 = k[M]^2.84[I_O]^0.51[I_R]^0.61 (where [M] is the total monomer concentration, [I_O] is the oxidant concentration, and [I_R] is the reductant concentration), respectively when the temperature was 45°C. The E_a values were E_a1 = 79.10 kJ/mol, E_a2 = 81.39 kJ/mol, E_a3 = 85.15 kJ/mol, E_a4 = 88.88 kJ/mol, and E_a5 = 90.61 kJ/mol in the temperature range 35–55°C, respectively. The reactivity ratios of DMDAAC and AM were r_DMDAAC = 0.14 and r_AM = 6.11 when the temperature was 45°C. The structure of PDA was characterized by Fourier transform infrared spectroscopy and ¹H-NMR. The results of the kinetic parameters explained the differences in the copolymerization rate and intrinsic viscosity of PDA with different cationicities. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

A Comparative Study of the Explosion Characteristics of IPN and IPN/JP‐10 Mixtures in Air Aerosols

This article presents a comparison of the explosion characteristics of mixtures of isopropyl nitrate (IPN, (CH₃)₂CHONO₂) and JP‐10 (C₁₀H₁₆, tricycle [5.2.1.0^2,6] decane) in air aerosols. The explosion pressure, flame temperature, maximum rate of pressure rise, maximum rate of temperature rise, and lower flammability limits (LFLs) were measured for two sets of IPN and mixed IPN/JP‐10 in air aerosols at different concentrations and Sauter mean diameters (SMDs) of 19 μm and 34 μm, respectively, and the values were compared with the experimental results of JP‐10/air aerosols with SMDs of 20 μm and 35 μm (from our previous research). Experiments were also performed to study various concentrations at various ignition energies for the IPN/air aerosols and the explosions of binary mixture aerosols with various mass ratios of IPN and JP‐10. The experimental results indicated that for the IPN/air and JP‐10/air aerosols with a mean SMD of ∼34 μm, the maximum peak pressure and maximum peak temperature of the IPN/air aerosols were greater than those of the JP‐10/air aerosols. The maximum rate of pressure rise of the IPN/air aerosols reached a maximum value of 395.3 MPa/s at a mean SMD of ∼34 μm, and the pressure increased more abruptly in the IPN/air aerosols than in the JP‐10/air aerosols. The LFLs of the IPN/air aerosols occurred with a total concentration of 197 g/m³ at a mean SMD of 19 μm and a total concentration of 233 g/m³ at a mean SMD of 34 μm, whereas the LFLs for the JP‐10/air aerosols with SMDs of 20 μm and 35 μm were less than 47 g/m³ and 40 g/m³, respectively. The experimental results presented here also showed that the maximum peak pressure was 1.07 MPa at a binary liquid mass ratio of IPN:JP‐10 (%) of 72 : 28 and a mean SMD of ∼34 μm.     

Conductive IPN based on polyaniline and silicon‐crosslinked styrene‐isoprene‐styrene triblock copolymer

A series of new conducting interpenetrating polymer networks (IPNs) are prepared by sequential crosslinking reactions of tetraethyl orthosilicate with silicon‐grafted functional styrene‐isoprene‐styrene triblock copolymer (SIS) and polyaniline (PANI) doped with dodecylbenzenesulfonic acid (DBSA). The various factors affecting the properties of conductive IPNs are investigated. The conductivity is found to increase only slightly after the IPN films are treated at 140 ° C . The thermal stability of the IPNs is much better than that of the pure polymer under nitrogen atmosphere, as shown by the results from thermal gravimetry analysis (TGA). © 1999 Society of Chemical Industry     

Copolymerization kinetics of poly(acrylonitrile‐ran‐2‐ethenyl‐pyridine) and its degradation apparent activation energy

2‐Ethenyl‐pyridine (EPD) was first used to successfully copolymerize with acrylonitrile (AN) in a H₂O/dimethyl formamide (DMF) mixture by using azobisisobutyronitrile as the initiator. Kinetics of copolymerization and degradation of poly(AN‐ran‐EPD) were discussed. The kinetic equation of copolymerization and the apparent activation energy of degradation of poly(AN‐ran‐EPD) were obtained. In H₂O‐rich reaction medium, copolymerization followed the suspension polymerization more, but in DMF‐rich reaction medium, copolymerization followed the solution polymerization more. Increase in DMF concentration in the solvent mixture lead to a rapid increase in the degradation apparent activation energy. The apparent activation energy decreased quickly with an increase in EPD concentration, and such a change became less prominent as the molar ratio of EPD/AN went beyond 3/100. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Kinetic study of radical polymerization. III. Solution polymerization of acrylamide by 1H‐NMR

Solution and radical polymerization of acrylamide in the presence of potassium persulfate in D₂O was investigated up to high conversion by high‐field ¹H‐NMR spectroscopy. The kinetics of reaction was studied according to the data obtained from the corresponding spectra at various times during the polymerization reaction progress. Processing of the data led us to derive the rate equation of this polymerization reaction and determine the reaction order of each component in the rate equation. The order, with respect to initiator, was consistent with the classical kinetic rate equation (0.45), whereas the order with respect to monomer was greater than unity (1.49). The effect of temperature on the polymerization rate was also investigated and the activation energy of 48.4 kJ mol^?1 was obtained over the temperature range of 60–75°C. Also some mechanistic studies were discussed. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2007–2013, 2004     

Curing kinetics and thermal property characterization of a bisphenol‐S epoxy resin and DDS system

The kinetics of the cure reaction for a system of bisphenol‐S epoxy resin (BPSER), with 4,4′‐diaminodiphenyl sulfone (DDS) as a curing agent was investigated with a differential scanning calorimeter (DSC). Autocatalytic behaviour was observed in the first stages of the cure which can well be described by the model proposed by Kamal, using two rate constants, k₁ and k₂, and two reaction orders, m and n. The overall reaction order, m + n, is in the range 2∼2.5, and the activation energy for k₁ and k₂ was 86.26 and 65.13 kJ mol⁻¹, respectively. In the later stages, a crosslinked network was formed and diffusion control was incorporated to describe the cure. The glass transition temperature (T_g) of the BPSER/DDS samples partially cured isothermally was determined by means of torsional braid analysis (TBA) and the results showed that the reaction rate increased with increasing T_g, in terms of rate constant, but decreased with increasing conversion. It was also found that the  SO₂ group both in the epoxy resin and in the hardener increases the T_g values of the cured materials compared with that of BPAER. The thermal degradation kinetics of this system was investigated by thermogravimetric analysis (TGA). It illustrated that the thermal degradation of BPSER/DDS has nth order reaction kinetics. © 2000 Society of Chemical Industry     

Curing kinetics and thermal property characterization of a bisphenol‐F epoxy resin and DDO system

The curing kinetics of a bisphenol‐F epoxy resin (BPFER)/4,4′‐diaminodiphenyl oxide (DDO) system were studied with isothermal experiments via differential scanning calorimetry. Autocatalytic behavior was shown in the first stages of the cure for the system, which was well described by the model proposed by Kamal that includes two rate constants, k₁ and k₂, and two reaction orders, m and n. The curing reaction at the later stages was practically diffusion‐controlled because of the onset of gelation and vitrification. For a more precise consideration of the diffusion effect, a diffusion factor, f(α), was introduced into Kamal's equation. In this way, the curing kinetics were predicted well over the entire range of conversion, covering both previtrification and postvitrification stages. The glass‐transition temperatures (T_g's) of the BPFER/DDO system partially isothermally cured were determined by means of torsional braid analysis, and the results showed that T_g's increased with conversion up to a constant value. The highest T_g was 376.3 K. The thermal degradation kinetics of cured BPFER were investigated with thermogravimetric analysis, which revealed two decomposition steps. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1586–1595, 2002     

二水硫酸钙溶解动力学

采用电导率法测量匀速旋转的石膏块试样(CaSO₄·2H₂O,质量分数为98%)在纯水中的溶解速率,数据采集时间间隔1 s,测试期间试样表观形状(7 cm×4 cm×2 cm)和面积(100 cm²)基本不变。在溶解过程为表面反应控制条件下,依据溶解反应动力学模型,拟合得到25、45、65、85℃下二水硫酸钙溶解反应速率常数分别为1.91×10^-8、3.46×10^-8、4.92×10^-8、7.07×10^-8 mol·cm^-2·s^-1,反应级数为1.27。经Arrhenius公式回归得到溶解反应表观活化能为19.07 kJ·mol^-1。本实验方法排除了溶解过程试样面积不确定因素,拟合得到的模型参数使动力学方程计算值与实验值更为吻合,更接近溶解速率理论预测文献值。     

Rate of imidization of polymerizable reaction mixtures: PMR-15

Imidization of PMR-15 was investigated using Fourier transform infrared spectroscopy (FTIR) as a function of time and temperature. Imidization was performed at 65 ≤ T ≤ 300°C for 3 ≤ t ≤ 150 min. FTIR spectroscopy showed that imidization (measured by the changes in the imide carbonyl absorption at 1778 cm⁻¹) increased with temperature and time. Imidization was found to be nearly completed in 2.5 h at 300°C. Imidization of PMR-15 occurred in three stages: (i) the initial imidization region characterized by gradual reaction followed by (ii) a very rapid reaction region that spans about 0.5 h and (iii) a final imidization region characterized by a gradual reaction and spans about 2 h. An Avrami-type kinetic analysis was used to obtain the reaction order of 1.5 and 1.7 and the rate constant for imidization of 1.3 × 10⁻³ and 1.5 × 10⁻³ min^−3/2; at 135 and 165°C, respectively. Comparison with other kinetic models shows agreement at low conversions (p ≤ 15%). At high conversions of p > 20%, a second-order kinetic model seems to fit the data reasonably well in agreement with the observed order. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 2529–2538, 1997     

无光釉的结晶动力学研究

本文通过差热分析(DTA)对无光釉的析晶动力学问题进行了研究,求出了它的析晶活化能E;并借用一种新的动力学判据Ky(T),给出了它析晶能力大小.并发现在无光釉中引入成核剂TiO2后会降低它的析晶能力,工艺条件的改变会使它的析晶活化能增大,析晶能力增强.     

Kinetic study on the UV‐induced photopolymerization of epoxy acrylate/TiO2 nanocomposites by FTIR spectroscopy

The kinetics of the photopolymerization of epoxy acrylate/TiO₂ nanocomposites, with 2′2‐dimethoxy‐1,2‐diphenylethan‐1‐one (Irgacure 651) or benzophenone/N‐methyl diethanolamine as photoinitiators, were studied by FTIR spectroscopy. It was found that nanocomposites had a decreasing photopolymerization rates in comparison with pure epoxy acrylate. The photopolymerization rate of the nanocomposite could also be influenced by initiator types, oxygen, film thickness, irradiation intensity, dispersing media of TiO₂ slurry, and so forth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3281–3287, 2006     

阻燃热塑性聚酯弹性体的热降解动力学研究

采用阻燃剂与单体共聚合成阻燃共聚热塑性聚酯弹性体(FR-TPEE),对FR-TPEE进行热失重分析,并采用Kissinger法,Flynn-Wall-Ozawa法和Coats-Redfern法对FR-TPEE热降解动力学进行研究。结果表明:FR-TPEE热降解过程分3个阶段,Kissinger法计算其活化能偏小,Flynn-Wall-Ozawa法和Coats-Redfern方法不适用于处理FR-TPEE热降解第三阶段。Coats-Redfern方法得知FR-TPEE第一阶段的降解机理是相界面控制反应机理,第二阶段是一维扩散机理。     

Effect of non‐rubber substances on vulcanization kinetics of natural rubber

Effect of non‐rubber components on vulcanization kinetics of natural rubber was studied with the use of a Rheometer MDR‐2000. The results show that the rate constants of induction period and curing period of natural rubber (NR) are greater than that of natural rubber extracted with acetone (NR_E), and the activation energies of induction period and curing period of NR are lower than that of NR_E. The activation energy of induction period of NR is reduced by16.9% and the activation energy of curing period of NR is reduced by 3.2% compared to the activation energies of NR_E. The time t_dis of NR is shorter than that of NR_E at the same temperature. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012