Influence of thermal annealing on electrical and optical properties of indium tin oxide thin films

Transparent conducting indium tin oxide (ITO) thin films with the thickness of 300 nm were deposited on quartz substrates via electron beam evaporation, and five of them post-annealed in air atmosphere for 10 min at five selected temperature points from 200 °C to 600 °C, respectively. An UV–vis spectrophotometer and Hall measurement system were adopted to characterize the ITO thin films. Influence of thermal annealing in air atmosphere on electrical and optical properties was investigated in detail. The sheet resistance reached the minimum of 6.67 Ω/sq after annealed at 300 °C. It increased dramatically at even higher annealing temperature. The mean transmittance over the range from 400 nm to 800 nm reached the maximum of 89.03% after annealed at 400 °C, and the figure of merit reached the maximum of 17.79 (Unit: 10⁻³ Ω⁻¹) under the same annealing condition. With the annealing temperature increased from 400 °C to 600 °C, the variations of transmittance were negligible, but the figure of merit decreased significantly due to the deterioration of electrical conductivity. With increasing the annealing temperature, the absorption edge shifted towards longer wavelength. It could be explained on the basis of Burstein–Moss shift. The values of optical band gap varied in the range of 3.866–4.392 eV.     

Optical and electrical properties of nickel oxide thin films synthesized by sol–gel spin coating

Nickel oxide thin films were prepared by the sol–gel technique combined with spin coating onto glass substrates. The as-deposited films were pre-heated at 275 °C for 15 min and then annealed in air at different temperatures. The effects of the annealing temperature on the structural and optical properties of the films are studied. The results show that 600 °C is the optimum annealing temperature for preparation of NiO films with p-type conductivity and high optical transparency. Then, by using these optimized deposition parameters, NiO thin films of various thicknesses were deposited at the same experimental conditions and annealed under different atmospheres. Surface morphology of the films was investigated by atomic force microscopy. The surface morphology of the films varies with the annealing atmosphere. Optical transmission was studied by UV–vis spectrophotometer. The transmittance of films decreased as the thickness of films increased. The electrical resistivity, obtained by four-point probe measurements, was improved when NiO layers were annealed in N₂ atmosphere at 600 °C.     

Effect of annealing temperature on optical and electrical properties of lead sulfide thin films

Lead sulfide (PbS) thin films with 150 nm thickness were prepared onto ultra-clean quartz substrate by the RF-sputtering deposition method. Deposited thin films of PbS were annealed at different temperatures 100 °C, 150 °C, 200 °C, 250 °C and 300 °C. X-ray diffraction pattern of thin films revealed that thin films crystallized at 150 °C. Crystalline thin films had cubic phase and rock salt structure. The average crystallite size of crystalline thin films was 22 nm, 28 nm and 29 nm for 150 °C, 200 °C and 250 °C respectively. From 150 °C to 250 °C increase in annealing temperature leads to increase in crystallite arrangement. FESEM images of thin films revealed that crystallite arrangement improved by increasing annealing temperature up to 250 °C. Increase in DC electrical conductivity by increasing temperature confirmed the semiconductor nature of crystalline thin films. Increase in dark current by increasing annealing temperature showed the effect of crystallite arrangement on carrier transport. Photosensitivity decreased by increasing annealing temperature for crystalline thin films that it was explained at the base of thermal quenching of photoconductivity and adsorption of oxygen at the surface of thin films that leads to the formation of PbO at higher temperatures.     

Effect of thermal annealing on physical properties of vacuum evaporated In2S3 buffer layer for eco-friendly photovoltaic applications

The present communication reports the effect of thermal annealing on the physical properties of In₂S₃ thin films for eco-friendly buffer layer photovoltaic applications. The thin films of thickness 150 nm were deposited on glass and indium tin oxide (ITO) coated glass substrates employing thermal vacuum evaporation technique followed by post-deposition thermal annealing in air atmosphere within a low temperature range 150–450 °C. These as-deposited and annealed films were subjected to the X-ray diffraction (XRD), UV–vis spectrophotometer, current–voltage tests and scanning electron microscopy (SEM) for structural, optical, electrical and surface morphological analysis respectively. The compositional analysis of as-deposited film is also carried out using energy dispersive spectroscopy (EDS). The XRD patterns reveal that the as-deposited and annealed films (≤300 °C) have amorphous nature while films annealed at 450 °C show tetragonal phase of β-In₂S₃ with preferred orientation (109) and polycrystalline in nature. The crystallographic parameters like lattice constant, inter-planner spacing, grain size, internal strain, dislocation density and number of crystallites per unit area are calculated for thermally annealed (450 °C) thin films. The optical band gap was found in the range 2.84–3.04 eV and observed to increase with annealing temperature. The current–voltage characteristics show that the as-deposited and annealed films exhibit linear ohmic behavior. The SEM studies show that the as-deposited and annealed films are uniform, homogeneous and free from crystal defects and voids. The grains in the thin films are similar in size and densely packed and observed to increase with thermal annealing. The experimental results reveal that the thermal annealing play significant role in the structural, optical, electrical and morphological properties of deposited In₂S₃ thin films and may be used as cadmium-free eco-friendly buffer layer for thin films solar cells applications.     

Enhancement in electrical performance of indium gallium zinc oxide-based thin film transistors by low temperature thermal annealing

We have studied the characteristics of transparent bottom-gate thin film transistors (TFTs) using In–Ga–Zn–O (IGZO) as an active channel material. IGZO films were deposited on SiO₂/Si substrates by DC sputtering techniques. Thereafter, the bottom-gate TFT devices were fabricated by depositing Ti/Au metal pads on IGZO films, where the channel length and width were defined to be 200 and 1000 μm, respectively. Post-metallization thermal annealing of the devices was carried out at 260, 280 and 300 °C in nitrogen ambient for 1 h. The devices annealed at 280 °C have shown better characteristics with enhanced field-effect mobility and high on–off current ratio. The compositional variation of IGZO films was also observed with different annealing temperatures.     

Defect modification in ZnInSnO transistor with solution-processed Al2O3 dielectric by annealing

The properties of solution-processed Al₂O₃ thin films annealed at different temperatures were thoroughly studied through thermogravimetry–differential thermal analysis, UV–vis-NIR spectrophotometer measurements, scanning electron microscopy, X-ray diffraction, atomic force microscopy and a series of electrical measurements. The solution-processed ZnInSnO thin films transistors (TFTs) with the prepared Al₂O₃ dielectric were annealed at different temperatures. The TFTs annealed at 600 °C have displayed excellent electrical performance such as the field-effect mobility of 116.9 cm² V⁻¹ s⁻¹ and a subthreshold slope of 93.3 mV/dec. The performance of TFT device could be controlled by adjusting the annealing temperature. The results of two-dimensional device simulations demonstrate that the improvement of device performance are closely related with the reduction of interface defects between channel and dielectric and subgap density of stats (DOS) in the channel layer.     

Annealing effects on physical properties of doped CdTe thin films for photovoltaic applications

Polycrystalline Cadmium Telluride (CdTe) thin films were prepared on glass substrates by thermal evaporation at the chamber ambient temperature and then annealed for an hour in vacuum ~1×10⁻⁵ mbar at 400 °C. These annealed thin films were doped with copper (Cu) via ion exchange by immersing these films in Cu (NO₃)₂ solution (1 g/1000 ml) for 20 min. Further these films were again annealed at different temperatures for better diffusion of dopant species. The physical properties of an as doped sample and samples annealed at different temperatures after doping were determined by using energy dispersive x-ray analysis (EDX), x-ray diffraction (XRD), Raman spectroscopy, transmission spectra analysis, photoconductivity response and hot probe for conductivity type. The optical band gap of these thermally evaporated Cu doped CdTe thin films was determined from the transmission spectra and was found to be in the range 1.42–1.75 eV. The direct energy band gap was found annealing temperatures dependent. The absorption coefficient was >10⁴ cm⁻¹ for incident photons having energy greater than the band gap energy. Optical density was observed also dependent on postdoping annealing temperature. All samples were found having p-type conductivity. These films are strong potential candidates for photovoltaic applications like solar cells.     

Investigation of optical and electronic properties in Al–Sn co-doped ZnO thin films

Al-Sn co-doped ZnO thin films were deposited onto quartz substrates by sol-gel processing. The surface morphology and electrical and optical properties were investigated at different annealing temperatures. The surface morphology showed a closely packed arrangement of crystallites in all the doped films. As prepared co-doped films show a preferred orientation along an (0 0 2) plane. This preferred orientation was enhanced by increasing the annealing temperature to between 400 °C and 500 °C, but there was a shift to the (1 0 1) plane when the annealing temperature rose above 500 °C. These samples show, on average, 91.2% optical transmittance in the visible range. In this study, the optical band gap of all the doped films was broadened compared with pure ZnO, regardless of the different annealing temperature. The carrier concentration and carrier mobility of the thin films were also investigated.     

Investigation of structural and optoelectronic properties of annealed nickel phthalocyanine thin films

Thin films of nickel phthalocyanine (NiPc) were prepared by thermal evaporation and the effects of annealing temperature on the structural and optical properties of the samples were studied using different analytical methods. Structural analysis showed that the grain size and crystallinity of NiPc films improved as annealing temperature increased from 25 to 150 °C. Also, maximum grain size (71.3 nm) was obtained at 150 °C annealing temperature. In addition, NiPc films annealed at 150 °C had a very smooth surface with an RMS roughness of 0.41 nm. Optical analysis indicated that band gap energy of films at different annealing temperatures varied in the range of 3.22–3.28 eV. Schottky diode solar cells with a structure of ITO/PEDOT:PSS/NiPc/Al were fabricated. Measurement of the dark current density–voltage (J–V) characteristics of diodes showed that the current density of films annealed at 150 °C for a given bias was greater than that of other films. Furthermore, the films revealed the highest rectification ratio (23.1) and lowest barrier height (0.84 eV) demonstrating, respectively, 23% and 11% increase compared with those of the deposited NiPc films. Meanwhile, photoconversion behavior of films annealed at 150 °C under illumination showed the highest short circuit current density (0.070 mA/cm²) and open circuit voltage of (0.55 V).     

Influence of annealing temperature on the phase composition and optical properties of CuInS2 films

We studied the growth of CuInS₂ thin films by single-source evaporation of CuInS₂ powder in a high-vacuum system with a base pressure of 10^?3 Pa. After evaporation, the films were annealed in a sulfur atmosphere at temperatures from 200 to 500 °C for 1 h. XRD curves and Raman spectra of the films demonstrated that chalcopyrite CuInS₂ was the major crystalline phase. The morphology of Cu_xS exhibited a star-like structure, which we report for the first time. The phase composition and optical properties of our polycrystalline thin films were effectively modified by annealing in S. For films annealed at 200 and 350 °C, a secondary CuIn₁₁S₁₇ phase appeared, which may be related to solid-state reaction in the S atmosphere. This secondary CuIn₁₁S₁₇ phase has not been widely reported in previous studies. After annealing at 500 °C, only a chalcopyrite phase was detected, with bandgap energy of 1.46 eV, which is nearly identical to the optimal bandgap energy (1.5 eV) of single-crystal CuInS₂. This indicates that the composition of the CuInS₂ film annealed at 500 °C was nearly stoichiometric. The bandgap of the samples first increased and then decreased with increasing annealing temperature, which may be attributed to an increase in grain size, the secondary CuIn₁₁S₁₇ phase, and deviation from stoichiometry.     

Structural and optoelectronic properties of nanostructured TiO2 thin films with annealing

About 480 nm thick titanium oxide (TiO₂) thin films have been deposited by electron beam evaporation followed by annealing in air at 300–600 °C with a step of 100 °C for a period of 2 h. Optical, electrical and structural properties are studied as a function of annealing temperature. All the films are crystalline (having tetragonal anatase structure) with small amount of amorphous phase. Crystallinity of the films improves with annealing at elevated temperatures. XRD and FESEM results suggest that the films are composed of nanoparticles of 25–35 nm. Raman analysis and optical measurements suggest quantum confinement effects since Raman peaks of the as-deposited films are blue-shifted as compared to those for bulk TiO₂ Optical band gap energy of the as-deposited TiO₂ film is 3.24 eV, which decreases to about 3.09 eV after annealing at 600 °C. Refractive index of the as-deposited TiO₂ film is 2.26, which increases to about 2.32 after annealing at 600 °C. However the films annealed at 500 °C present peculiar behavior as their band gap increases to the highest value of 3.27 eV whereas refractive index, RMS roughness and dc-resistance illustrate a drop as compared to all other films. Illumination to sunlight decreases the dc-resistance of the as-deposited and annealed films as compared to dark measurements possibly due to charge carrier enhancement by photon absorption.     

Effect of annealing temperature on structural,electrical and optical properties of spray pyrolytic nanocrystalline CdO thin films

Nanocrystalline CdO thin films were prepared onto a glass substrate at substrate temperature of 300 °C by a spray pyrolysis technique. Grown films were annealed at 250, 350, 450 and 550 °C for 2.5 h and studied by the X-ray diffraction, Hall voltage measurement, UV-spectroscopy, and scanning electron microscope. The X-ray diffraction study confirms the cubic structure of as-deposited and annealed films. The grain size increases whereas the dislocation density decreases with increasing annealing temperature. The Hall measurement confirms that CdO is an n-type semiconductor. The carrier density and mobility increase with increasing annealing temperature up to 450 °C. The temperature dependent dc resistivity of as-deposited film shows metallic behavior from room temperature to 370 K after which it is semiconducting in nature. The metallic behavior completely washed out by annealing the samples at different temperatures. Optical transmittance and band gap energy of the films are found to decrease with increasing annealing temperature and the highest transmittance is found in near infrared region. The refractive index and optical conductivity of the CdO thin films enhanced by annealing. Scanning electron microscopy confirms formation of nano-structured CdO thin films with clear grain boundary.     

Effects of RTA temperatures on conductivity and micro-structures of boron-doped silicon nanocrystals in Si-rich oxide thin films

In this work, the B-doped Si rich oxide (SRO) thin films were deposited and then annealed using rapid thermal annealing (RTA) to form SiO₂-matrix silicon nanocrystals (Si NCs). The effects of the RTA temperatures on the structural properties, conduction mechanisms and electrical properties of B-doped SRO thin films (BSF) were investigated systematically using Hall measurements, Fourier transform infrared spectroscopy and Raman spectroscopy. Results showed that the crystalline fraction of annealed BSF increased from 41.3% to 62.8%, the conductivity was increased from 4.48×10⁻³ S/cm to 0.16 s/cm, the carrier concentration was increased from 8.74×10¹⁷ cm⁻³ to 4.9×10¹⁸ cm⁻³ and the carrier mobility was increased from 0.032 cm² V⁻¹ s⁻¹ to 0.2 cm² V⁻¹ s⁻¹ when the RTA temperatures increased from 1050 °C to 1150 °C. In addition, the fluctuation induced tunneling (FIT) theory was applicable to the conduction mechanisms of SiO₂-matrix boron-doped Si-NC thin films.     

Behavior of chemically deposited PbS thin films subjected to two different routes of post deposition annealing

Lead sulfide (PbS) thin films were prepared on soda lime glass substrates at room temperature by Chemical Bath Deposition (CBD) technique. This paper reports a comparative study of characteristic properties of as-prepared PbS thin films after thermal treatment through two different routes. Studies were carried out for as-prepared as well as rapidly and gradually annealed samples at 100, 200 and 300 °C. The characterizations of the films were carried out using X-ray diffraction, scanning electron microscopy and optical measurement techniques. The structural studies confirmed the polycrystalline nature and the cubic structure of the films. As-deposited films partly transformed to Pb₂O₃ when gradually annealed to 300 °C. The presence of nano crystallites was revealed by structural and optical absorption measurements. The values of average crystallite size were found to be in the range 18–20 nm. The variation in the microstructure, thickness, grain size, micro strain and optical band gap on two types of annealing were compared and analyzed. Data showed that post deposition parameters and thermal treatment strongly influence the optical properties of PbS films. Optical band gap of the film gets modified remarkably on annealing. Direct band gap energy values for rapidly and gradually annealed samples varied in the range of 1.68–2.01 eV and 1.68–2.12 eV respectively. Thus we were succeeded in tailoring direct band gap energies by post deposition annealing method.     

Effect of annealing on structural,optical and electrical properties of pulse electrodeposited tin sulfide films

Polycrystalline tin sulfide (SnS) thin films were grown on conducting glass substrates by pulse electrodeposition. The effect of annealing on the physical properties such as structure, morphology, optical, and opto-electronic properties were evaluated to understand the effect of post-deposition treatment for SnS films. Annealing at temperatures higher than 250 °°C resulted in the formation of SnS₂ as a second phase, however, no significant grain growth or morphological changes were observed for films after annealing at 350 °C. A small change in band gap of 0.1 eV observed for films annealed at 350 °C was interpreted as due to the formation of SnS₂ rather than due to morphological changes. This interpretation was supported by X-ray diffractometry, scanning electron microscopy, and Raman spectral data. The electric conduction in the films is controlled by three shallow trap levels with activation energies 0.1, 0.05, and 0.03 eV. The trap with energy 0.03 eV disappeared after annealing at higher temperature, however, the other two traps were unaffected by annealing.     

Impact of vacuum and nitrogen annealing on HVE SnS photoabsorber films

Researchers worldwide focus on new earth abundant and cheap absorber materials for use in thin film solar cells that allow wider use of photovoltaics in energy production. SnS is one of such promising absorber materials that comprises earth abundant elements (Sn, S). We describe here the effect of annealing of high vacuum evaporated (HVE) SnS thin films in vacuum and nitrogen atmosphere with relatively high pressures of nitrogen. SnS thin films with a thickness of 500 nm were deposited onto the surface of glass by HVE at a substrate temperature of 300 °C. The as-deposited SnS thin films were annealed at 500 °C and 550 °C for 1 h in vacuum as well as in nitrogen with respect to ambient (N₂) pressure that varied in the range of 500–2000 mbar. We analyze crystalline quality, crystal structure, elemental and phase compositions, and electrical properties of SnS films before and after the annealing process and their changes. Our results show that the use of pressurized inert ambient, such as nitrogen, improves the crystalline quality as well as the electrical properties of SnS thin films. The enhanced growth of crystals and modification of microstructural properties of SnS thin films as a function of annealing conditions (type of ambient, annealing temperature and ambient pressure) are discussed in detail.     

Effect of rapid thermal annealing on properties of thermally evaporated nanostructured CdTe thin film treated with CdCl2

The effects of rapid thermal annealing on properties of crystalline nanostructured CdTe films treated with CdCl₂ and prepared by vacuum evaporation are described. X-ray diffraction confirmed the crystalline nature of post-treated films with high preferential orientation around 23.7°, corresponding to a (1 1 1) diffracted plane of cubic phase. Optical band gap of CdTe films increased from 1.4 eV to 1.48 eV after annealing at 500 °C for 90 s. Atomic force microscopy of annealed films revealed an increase in root mean square roughness and grain size with increased annealing time. Electrical measurements of as-grown and annealed films are consistent with p-type; film resistivity has decreased significantly with increased annealing time.     

Evaporated iron disulfide thin films with sulfurated annealing treatments

FeS₂ thin films were grown on a glass substrate using a physical vapor deposition technique at room temperature. Subsequently, the thin films were annealed in two different atmospheres: vacuum and vacuum-sulfur. In the vacuum-sulfur atmosphere a graphite box was used as sulfur container and the films were sulfurated successfully at 200–350 ºC. It was found that annealing in a vacuum-sulfur atmosphere was indispensable in order to obtain polycrystalline FeS₂ thin films. The polycrystalline nature and pure phase were determined by XRD and Raman techniques and the electrical properties by the Hall effect. Using the sulfurating technique, the n-type semiconductor was prepared at 200–350 °C and a p-type at 500 °C. The carrier concentrations were between 1.19×10²⁰ and 2.1×10²⁰ cm⁻³. The mobility was 9.96–5.25 cm² V⁻¹ s⁻¹ and the resistivity was 6.31×10⁻² to 1.089×10⁻² Ω cm. The results obtained from EDS showed that the films prepared in the vacuum-sulfur atmosphere were close to stoichiometric and that the indirect band gap varied between 1.03 and 0.945 eV.     

Fabrication of Ag nanoparticle/ZnO thin films using dual-plasma-enhanced metal-organic chemical vapor deposition (DPEMOCVD) system incorporated with photoreduction method and its application

We report a novel method to grow silver nanoparticle/zinc oxide (Ag NP/ZnO) thin films using a dual-plasma-enhanced metal-organic chemical vapor deposition (DPEMOCVD) system incorporated with a photoreduction method. The crystalline quality, optical properties, and electrical characteristics of Ag NP/ZnO thin films depend on the AgNO₃ concentration or Ag content and annealing temperature. Optimal Ag NP/ZnO thin films have been grown with a AgNO₃ concentration of 0.12 M or 2.54 at%- Ag content and 500 °C- rapid thermal annealing (RTA); these films show orientation peaks of hexagonal-wurtzite-structured ZnO (002) and face-center-cubic-crystalline Ag (111), respectively. The transmittance and resistivity for optimal Ag NP/ZnO thin films are 85% and 6.9×10⁻⁴ Ω cm. Some Ag NP/ZnO transparent conducting oxide (TCO) films were applied to InGaN/GaN LEDs as transparent conductive layers. The InGaN/GaN LEDs with optimal Ag NP/ZnO TCO films showed electric and optical performance levels similar to those of devices fabricated with indium tin oxide.