Determination of CaO–SiO2–MgO–Al2O3–CrOx Liquidus

In this work, the liquidus of synthetic CaO–SiO₂–MgO–Al₂O₃–CrO _x slags is evaluated in the industrially relevant compositional domain. Equilibrium experiments are carried out at 1500°C and partial oxygen pressure ( p _O2) 10^−11.04 atm, and at 1600°C and p _O2=10^−10.16 and 10^−9.36 atm. The studied basicities (CaO/SiO₂) are 1.2 and 0.5. Al₂O₃ levels range from 0 to 30 wt%. Oversaturated liquid is sampled and phase relations are measured with quantitative electron probe microanalysis–wavelength dispersive spectroscopy (EPMA–WDS). The results are compared with the commercially available FactSage thermodynamic databases. Qualitative agreement is always obtained. Also a good quantitative agreement is found at the higher basicity, especially for the spinel liquidus. A minor but systematic deviation can be observed for the eskolaite liquidus. At the lower basicity, the calculated phase diagram deviates strongly from the experimental results, probably due to missing ternary interactions in the database.     

Thermodynamic Modeling of the MgO–Al2O3–CrO–Cr2O3 System

A complete critical evaluation and thermodynamic modeling of the phase diagrams and thermodynamic properties of the MgO–Al₂O₃–CrO–Cr₂O₃ system at 1 bar total pressure are presented. Optimized equations for the thermodynamic properties of all phases are obtained which reproduce all available thermodynamic and phase equilibrium data within experimental error limits from 25°C to above the liquidus temperatures at all compositions and oxygen partial pressures. The optimized thermodynamic properties and phase diagrams are believed to be the best estimates presently available. The database of the model parameters can be used along with software for Gibbs energy minimization in order to calculate any type of phase diagram section.     

Quaternary System Al2O3–CaO–MgO–SiO2: I, Study of the Crystallization Volume of Al2O3

Compatibility relations of Al₂O₃ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching followed by microstructural and energy-dispersive X-ray examination. A projection of the liquidus surface of the primary phase volume of Al₂O₃ was constructed in terms of the CaO, SiO₂, and MgO contents of the mixtures recalculated to 100 wt%. Two invariant points, where four solids coexist with a liquid phase, were defined, and the positions of the isotherms were tentatively established. The effect of SiO₂, MgO, and CaO impurities on Al₂O₃ growth also was studied.     

Phase Equilibrium Relationships in a Portion of the System MgO–Al2O3–2CaO·SiO2

The system MgO–Al₂O₃–2CaO·SiO₂ comprises a plane through the tetrahedron CaO–MgO–Al₂O₃–SiO₂. A total of 108 compositions were prepared having an alumina content below the line joining 2CaO·Al₂O₃SiO₂ (gehlenite) and MgO·Al₂O₃ (spinel). Quenching experiments were carried out on 96 of these compositions at temperatures up to 1590°C. Three binary eutectic systems and two ternary eutectic systems are described. Compositions on this plane are of significance in an investigation of the constitution of basic refractory clinkers made from Canadian dolomitic magnesites. They also concern the compositions of certain blast furnace slags.     

Phase Equilibrium Relationships at Liquidus Temperatures in the System FeO–Fe2O3–Al2O3–SiO2

Phase equilibrium data at liquidus temperatures are presented for mixtures in the system FeO–Fe₂O₃–Al₂O₃–SiO₂. The volume located between the 1 and 0.2 atm. O₂ isobaric surfaces of the tetrahedron representing this system was studied in detail. Scattered data were obtained at lower O₂ pressures. Results obtained in the present investigation were combined with data in the literature to construct a phase equilibrium diagram, at liquidus temperatures, for the entire system FeO–Fe₂O₃–Al 2 O₃–SiO₂. Methods for interpretation of the diagram are explained.     

Quaternary System Al2O3–CaO–MgO–SiO2: II Study of the Crystallization Volume of MgAl2O4

Solid-state compatibility and melting relations of MgAl₂O₄ in the quaternary system Al₂O₃–CaO–MgO–SiO₂ were studied by firing and quenching selected samples located in the 65 wt% MgAl₂O₄, plane followed by microstructural and energy dispersive X-ray analysis. A projection of the liquidus surface of the primary crystallization volume of MgAl₂O₄ was constructed from CaO, SiO₂ and exceeding Al₂O₃, not involved in stoichiometric MgAl₂O₄ formation; those three amounts were recalculated to 100 wt%. The temperature and character of six invariant points, where four solids co-exist with a liquid phase, were defined. One maximum point was localized and the positions of the isotherms were tentatively established. The effect of CaO, SiO₂, and Al₂O₃ impurities on the high temperature behavior of spinel materials was also discussed.     

Thermodynamic Modeling of the FeO–Fe2O3–MgO–SiO2 System

The liquid and solid phases in the FeO–Fe₂O₃–MgO–SiO₂ system are of importance in ceramics, metallurgy, and petrology. A complete critical evaluation and thermodynamic modeling of the phase diagrams and thermodynamic properties of this system are presented. Optimized equations for the thermodynamic properties of all phases are obtained that reproduce all available thermodynamic and phase equilibrium data within experimental error limits from 25°C to above the liquidus temperatures at all compositions and oxygen partial pressures. The optimized thermodynamic properties and phase diagrams are believed to be the best estimates presently available. The database of the model parameters can be used with software for Gibbs energy minimization to calculate any type of phase diagram section.     

Thermodynamic Modeling of the Isomorphous Phase Diagrams in the Al2O3–Cr2O3 and V2O3–Cr2O3 Systems

The phase diagrams in the Al₂O₃–Cr₂O₃ and V₂O₃–Cr₂O₃ systems have been assessed by thermodynamic modeling with existing data from the literature. While the regular and subregular solution models were used in the Al₂O₃–Cr₂O₃ system to represent the Gibbs free energies of the liquid and solid phases, respectively, the regular solution model was applied to both phases in the V₂O₃–Cr₂O₃ system. By using the liquidus, solidus, and/or miscibility gap data, the interaction parameters of the liquid and solid phases were optimized through a multiple linear regression method. The phase diagrams calculated from these models are in good agreement with experimental data. Also, the solid miscibility gap and chemical spinodal in the V₂O₃–Cr₂O₃ system were estimated.     

Sintering and Crystallization of CaO–Al2O3–ZrO2–SiO2 Glasses Containing Different Amount of Al2O3

In this work several complementary techniques have been employed to carefully characterize the sintering and crystallization behavior of CaO–Al₂O₃–ZrO₂–SiO₂ glass powder compacts after different heat treatments. The research started from a new base glass 33.69 CaO–1.00 Al₂O₃–7.68 ZrO₂–55.43SiO₂ (mol%) to which 5 and 10 mol% Al₂O₃ were added. The glasses with higher amounts of alumina sintered at higher temperatures (953°C [lower amount] vs. 987°C [higher amount]). A combination of the linear shrinkage and viscosity data allowed to easily find the viscosity values corresponding to the beginning and the end of the sintering process. Anorthite and wollastonite crystals formed in the sintered samples, especially at lower temperatures. At higher temperatures, a new crystalline phase containing ZrO₂ (2CaO·4SiO₂·ZrO₂) appeared in all studied specimens.     

Oxidation State of Chromium in CaO–Al2O3–CrOx–SiO2 Melts under Strongly Reducing Conditions at 1500°C

Equilibrium ratios Cr²⁺/Cr³⁺ of chromium oxide dissolved in CaO–chromium oxide–Al₂O₃–SiO₂ melts have been determined by analysis of samples equilibrated at 1500°C under strongly reducing conditions ( p _o2= 10^−9.56 to 10^−12.50 atm). The majority of the chromium is divalent (Cr²⁺) under these conditions and Cr²⁺/Cr³⁺ ratios at given constant oxygen pressures decrease with increasing basicity of the melts, expressed as CaO/SiO₂ ratios. In addition, Cr²⁺/Cr³⁺ ratios, at a given CaO/SiO₂ ratio, are relatively unaffected by the amount of Al₂O₃ present.     

Phase Relations in the System Iron Oxide—Cr2O3 in Air

The quenching method has been used to determine approximate phase relations in the system iron oxide-Cr₂O₃ in air. Only two crystalline phases, a sesquioxide solid solution (Fe₂O₃–Cr₂O₃) with corundum structure and a spinel solid solution (approximately FeO ·Fe₂O₃–FeO – Cr₂O₃), occur in this system at conditions of temperature and O₂ partial pressure (0.21 atm.) used in this investigation. Liquidus temperatures increase rapidly as Cr₂O₃ is added to iron oxide, from 1591°C. for the pure iron oxide end member to a maximum of approximately 2265°C. for Cr₂O₃. Spinel(ss) is the primary crystalline phase in iron oxide-rich mixtures and sesquioxide (ss) in Cr₂O₃–rich mixtures. These two crystalline phases are present together in equilibrium with a liquid and gas (po₂= 0.21 atm.) at approximately 2075°C.     

Experimental Establishment of the CaAl2O4–MgO and CaAl4O7–MgO Isoplethal Sections within the Al2O3–MgO–CaO Ternary System

The isoplethal sections CaAl₂O₄–MgO and CaAl₄O₇–MgO of the Al₂O₃–MgO–CaO ternary system have been experimentally established at 1 bar total pressure and air of normal humidity. The sections obtained provide new data and information that are in disagreement with thermodynamic evaluations and optimizations of the Al₂O₃–MgO–CaO ternary system published to date. These differences arise mainly from the inclusion, or exclusion, of the binary compound Ca₁₂Al₁₄O₃₃, mayenite, as a stable phase in the reported studies of the system. The presence or absence of this compound within the system has an important impact on the solid state and melting relationships of the whole ternary system. The present study confirms the solid-state compatibility CaAl₂O₄–MgO and CaAl₂O₄–MgO–MgAl₂O₄ up to 1372°± 2°C, the peritectic melting point of the later mentioned subsystem.     

Effect of Alkali Metal Oxide Addition on the Sinterability of MgO–B2O3–Al2O3 Glass–Al2O3 Filler Composites

The sintering of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler is terminated due to the crystallization of Al₄B₂O₉ in the glass. The densification of a composite of MgO–B₂O₃–Al₂O₃ glass and Al₂O₃ filler using pressureless sintering was accomplished by lowering the sintering temperature of the composite. The sintering temperature was lowered by the addition of small amounts of alkali metal oxides to the MgO–B₂O₃–Al₂O₃ glass system. The resultant composite has a four-point bending strength of 280 MPa, a coefficient of thermal expansion (RT—200°C) of 4.4 × 10⁻⁶ K⁻¹, a dielectric constant of 6.0 at 1 MHz, porosity of approximately 1%, and moisture resistance.     

Oxidation/Vaporization Kinetics of Cr2O3

The weight loss of Cr₂O₃ in oxidizing environments (Po₂= 1 to 10⁻³ atm) at 1200°C was measured. Both hot-pressed and sintered Cr₂O₃ pellets were investigated in O₂/Ar gas mixtures, and the dependence of the weight loss on the O₂ partial pressure, the gas flow rate, and the total pressure was determined independently. The experimentally determined O₂ partial pressure dependence (rate ∝ PO₂^3/4) corresponds to that expected for the reaction Cr₂O₃(s)+3/2O₂⇌2CrO₃(g). The flow rate and total pressure dependencies show that mass transport through a gaseous boundary layer is the rate-controlling step in the oxidation/vaporization of Cr₂O₃. Evaporation coefficients for the loss of CrO₃(g) under the experimental conditions were <0.01.     

Al2O3–ZrO2–SiO2 Ternary Glasses for Molybdenum Oxidation Barriers

The wettability of binary and ternary glasses belonging to SiO₂–Al₂O₃–ZrO₂ diagram has been studied using the sessile drop technique at 1750° and 1800°C. The ternary SiO₂–Al₂O₃–ZrO₂ (90–5–5 wt%) glass has proved to be well appropriated as a molybdenum oxidation barrier coating. The addition of 5 wt% of MoO₂ slightly improves its wettablity at higher temperatures without affecting its oxidation barrier properties. The Mo comes into the glass network as a mixture of Mo⁵⁺, Mo⁴⁺, and Mo⁶⁺. After oxidation at 1000°C in oxygen atmosphere, the molybdenum remains in the glass network as Mo⁶⁺.     

Calcium Hexaluminate and Its Stability Relations in the System CaO–Al2O3–SiO2

By a combination of solid-state sintering and quenching experiments the validity of calcium hexaluminate as a stable phase and the extent of its primary field in the system CaO–Al₂O₃–SiO₂ have been established. The size of the primary field is considerably reduced from that suggested by earlier work. The anorthite-corundum-calcium hexaluminate invariant point has been relocated at 28.0% CaO, 39.7% Al₂O₂, and 32.3% SiO₂ and at 1405°± 5°C.     

Dissolution of MgO in CaO–"FeO"–CaF2–SiO2 Slags under Static Conditions

The dissolution of MgO in CaO–"FeO"–CaF₂–SiO₂ slags has been studied in the temperature range 1573°–1673° K under static conditions. The concentration profiles of Mg in the product Mg_1-xFe_xO solid-solution layer as well as slag were determined by EDS analysis. From this, the diffusivities of MgO in the slag and the. interdiffusivities in solid solution were estimated. The dissolution of MgO in CaO–"FeO"–CaF₂–SiO₂ slags increased with CaF₂ content.     

Energetics of La2O3–HfO2–SiO2 Glasses

A series of La₂O₃–HfO₂–SiO₂ glasses, approximately along the join 0.73SiO₂–0.27( x HfO₂–(1− x )La₂O₃), 0< x <0.3), was prepared using containerless processing techniques (aerodynamic levitation combined with laser heating in oxygen). The enthalpy of formation and enthalpy of vitrification at 25°C were obtained from drop solution calorimetry of these glasses and appropriate crystalline compounds in a molten lead borate (2PbO–B₂O₃) solvent at 702°C. The enthalpy of formation from crystalline oxides was exothermic and became less exothermic with increasing HfO₂ content. Heat contents were measured by transposed temperature drop calorimetry and depended linearly on the HfO₂ content. Differential scanning calorimetry showed that both the onset glass transition and the onset crystallization temperature of these glasses increased with increasing HfO₂ content. Upon slow cooling in air, the glasses crystallized to a mixture of baddeleyite, cristobalite, lanthanum disilicate, and hafnon.     

Effect of Sb2O3 on Thermal Properties of Glasses in Bi2O3–B2O3–SiO2 System

Glasses with compositions 50Bi₂O₃– x Sb₂O₃–10B₂O₃–(40– x ) SiO₂ ( x =0, 1, 3, 5, 8, 10) have been prepared by conventional melt quench technique. Substitution of Sb₂O₃ for SiO₂ exerted an obvious effect on properties of glasses, especially, increased glass transition temperature ( T _g) and crystalline temperature ( T _c) greatly. Results of infrared transmission spectra attributed the effect to the formation of new bridging bonds of Sb–O–B and Sb–O–Si in glass network.