Glass transition behavior of polypropylene/polystyrene/styrene-ethylene-propylene block copolymer blends

Summary The glass transition behavior of ternary blends of polypropylene (PP), polystyrene (PS) and styrene-ethylene-propylene-styrene block copolymer (SEPS) was investigated. The blends were prepared by an internal mixer, and their dynamic mechanical properties and morphology were measured. The blends showed phase inversion at around 75wt% PS composition. The glass transition temperature (T_g) of the PP phase shifted to lower temperature as the PS contents were increased in PP/PS binary blends, probably due to the mismatch of thermal expansion coefficients between two components. As the SEPS copolymer contents were increased, the T_g's of the PP phase in the blends increased. In particular, the large increase in T_g of the PP phase was observed in the PP/PS (25/75) blends where the phase inversion takes place. Received: 2 February 1998/Revised version: 24 March 1998/Accepted: 13 April 1998     

Morphological effects on glass transition behavior in selected immiscible blends of amorphous and semicrystalline polymers

The effects uncompatibilized immiscible polymer blend compositions on the T_g of the amorphous polymer were studied in the systems polystyrene/polypropylene (PS/PP), polystyrene/high density polyethylene (PS/PE) and polycarbonate/high density polyethylene (PC/PE). In the two similar systems of PS/PP and PS/PE, the T_g of PS increased with decreasing PS percentage in the blends. This variation in glass transition is attributed to the polymer domain interactions resulting from the different morphologies of various blend compositions. Experiments were conducted to study these effects by preparing blends with various polymers that varied the relationship between the T_g of the amorphous polymer and the crystallization behavior of the semicrystalline polymer. Results show that the variation in amorphous component T_g with composition depends strongly on the physical state of the semicrystalline domains. Whereas the T_g of PS in PS/PE blends changed with composition, the T_g of PC in the PC/PE blend did not change with composition.     

Nonisothermal crystallization kinetics of polypropylene/polypropylene‐g‐polystyrene/polystyrene blends

The nonisothermal crystallization kinetics of polypropylene (PP), PP/polystyrene (PS), and PP/PP‐g‐PS/PS blends were investigated with differential scanning calorimetry at different cooling rates. The Jeziorny modified Avrami equation, Ozawa method, and Mo method were used to describe the crystallization kinetics for all of the samples. The kinetics parameters, including the half‐time of crystallization, the peak crystallization temperature, the Avrami exponent, the kinetic crystallization rate constant, the crystallization activation energy, and the F(T) and a parameters were determined. All of the results clearly indicate that the PP‐g‐PS copolymer accelerated the crystallization rate of the PP component in the PP/PP‐g‐PS/PS blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis of polypropylene graft copolymers from a hydroxyl‐groups‐containing polypropylene precursor via atom‐transfer radical polymerization

Isotactic polypropylene graft copolymers, isotactic[polypropylene‐graft‐poly(methyl methacrylate)] (i‐PP‐g‐PMMA) and isotactic[polypropylene‐graft‐polystyrene] (i‐PP‐g‐PS), were prepared by atom‐transfer radical polymerization (ATRP) using a 2‐bromopropionic ester macro‐initiator from functional polypropylene‐containing hydroxyl groups. This kind of functionalized propylene can be obtained by copolymerization of propylene and borane monomer using isospecific MgCl₂‐supported TiCl₄ as catalyst. Both the graft density and the molecular weights of i‐PP‐based graft copolymers were controlled by changing the hydroxyl group contents of functionalized polypropylene and the amount of monomer used in the grafting reaction. The effect of i‐PP‐g‐PS graft copolymer on PP‐PS blends and that of i‐PP‐g‐PMMA graft copolymer on PP‐PMMA blends were studied by scanning electron microscopy. Copyright © 2006 Society of Chemical Industry     

Fabrication of polypropylene blends with excellent low‐temperature toughness and balanced toughness‐rigidity by a combination of EPR and SEEPS

To overcome serious rigidity depression of rubber‐toughened plastics and fabricate a rigidity‐toughness balanced thermoplastic, a combination of styrene‐[ethylene‐(ethylene‐propylene)]‐styrene block copolymer (SEEPS) and ethylene‐propylene rubber (EPR) was used to toughen polypropylene. The dynamic mechanical properties, crystallization and melting behavior, and mechanical properties of polypropylene (PP)/EPR/SEEPS blends were studied in detail. The results show that the combination of SEEPS and EPR can achieve the tremendous improvement of low‐temperature toughness without significant strength and rigidity loss. Dynamic mechanical properties and phase morphology results demonstrate that there is a good interfacial strength and increased loss of compound rubber phase comprised of EPR component and EP domain of SEEPS. Compared with PP/EPR binary blends, although neither glass transition temperature (T_g) of the rubber phase nor T_g of PP matrix in PP/EPR/SEEPS blends decreases, the brittle‐tough transition temperature (T_bd) of PP/EPR/SEEPS blends decreases, indicating that the increased interfacial interaction between PP matrix and compound rubber phase is also an effective approach to decrease T_bd of the blends so as to improve low‐temperature toughness. The balance between rigidity and toughness of PP/EPR/SEEPS blends is ascribed to the synergistic effect of EPR and SEEPS on toughening PP. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45714.     

Effect of confinement on glass dynamics and free volume in immiscible polystyrene/high‐density polyethylene blends

The effect of confinement on glass dynamics combined with the corresponding free volume changes of amorphous polystyrene (PS) in blends with semi‐crystalline high‐density polyethylene (HDPE) have been investigated using thermal analyses and positron annihilation lifetime spectroscopy (PALS). Two different glass transition temperatures (T_g) were observed in a PS/HDPE blend due to the dissimilarity in the chemical structure, consistent with an immiscible blend. However, T_g of PS in the incompatible PS/HDPE blend showed an upward trend with increasing PS content resulting from the confinement effect, while T_g of the semi‐crystalline HDPE component became lower than that of neat HDPE. Moreover, the elevation of T_g of PS was enhanced with a decrease of free volume radius by comparing annealed and unannealed PS/HDPE blends. Positron results showed that the free volume radius clearly decreased with annealing for all compositions, although the free volume hole size agreed well with linear additivity, indicating that there was only a weak interaction between the two components. Combining PALS with thermal analysis results, the confinement effect on the glass dynamics and free volume of PS phase in PS/HDPE blends could be attributed to the shrinkage of HDPE during crystallization when HDPE acted as the continuous phase. © 2015 Society of Chemical Industry     

In situ compatibilization of polypropylene/polystyrene blend by controlled degradation and reactive extrusion

In situ compatibilization of polypropylene (PP) and polystyrene (PS) was achieved by combinative application of tetraethyl thiuram disulfide (TETD) as degradation inhibitor and di‐tert‐butyl peroxide as degradation initiator in the process of reactive extrusion. The PP/PS blends obtained were systematically investigated by rheological measurement, scanning electron microscopy, and differential scanning calorimetry. The results indicate that peroxide‐induced degradation of PP can be effectively depressed by adding TETD, which may favor the formation of PP‐g‐PS copolymer during melt processing. The PP‐g‐PS copolymer formed may act as an in situ compatibilizer for PP/PS blends, and subsequently decreases the size of dispersed PS phase and changes both rheological and thermal properties of the blends. Based on the present experimental results, the mechanisms for the controlled degradation of PP and in situ formation of PP‐g‐PS copolymer in the PP/PS blends have been proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Relationship between branch length and the compatibilizing effect of polypropylene‐g‐polystyrene graft copolymer on polypropylene/polystyrene blends

Three polypropylene‐g‐polystyrene (PP‐g‐PS) graft copolymers with the same branch density but different branch lengths were evaluated as compatibilizing agents for PP/PS blends. The morphological and rheological results revealed that the addition of PP‐g‐PS graft copolymers significantly reduced the PS particle size and enhanced the interfacial adhesion between PP and PS phases. Furthermore, it is verified that the branch length of PP‐g‐PS graft copolymer had opposite effects on its compatibilizing effect: on one hand, increasing the branch length could improve the compatibilizing effect of graft copolymer on PP/PS blends, demonstrated by the reduction of PS particle size and the enhancement of interfacial adhesion; on the other hand, increasing the branch length would increase the melt viscosity of PP‐g‐PS graft copolymer, which prevented it from migrating effectively to the interface of blend components. Additionally, the crystallization and melting behaviors of PP and PP/PS blends were compared. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40126.     

Thermal behavior and properties of polystyrene/poly(methyl methacrylate) blends

The thermal behavior and properties of immiscible blends of polystyrene (PS) and poly(methyl methacrylate) (PMMA) with and without PS‐b‐PMMA diblock copolymer at different melt blending times were investigated by use of a differential scanning calorimeter. The weight fraction of PS in the blends ranged from 0.1 to 0.9. From the measured glass transition temperature (T_g) and specific heat increment (ΔC_p) at the T_g, the PMMA appeared to dissolve more in the PS phase than did the PS in the PMMA phase. The addition of a PS‐b‐PMMA diblock copolymer in the PS/PMMA blends slightly promoted the solubility of the PMMA in the PS and increased the interfacial adhesion between PS and PMMA phases during processing. The thermogravimetric analysis (TGA) showed that the presence of the PS‐b‐PMMA diblock copolymer in the PS/PMMA blends afforded protection against thermal degradation and improved their thermal stability. Also, it was found that the PS was more stable against thermal degradation than that of the PMMA over the entire heating range. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 609–620, 2004     

Polystyrene composites of single‐walled carbon nanotubes‐graft‐polystyrene

Single‐walled carbon nanotubes (SWCNTs) dispersed in N‐methylpyrrolidone (NMP) were functionalized by addition of polystyryl radicals from 2,2,6,6‐tetramethyl‐1‐piperidinyloxy‐ended polystyrene (SWCNT‐g‐PS). The amount of polystyrene grafted to the nanotubes was in the range 20‐25 wt% irrespective of polystyrene number‐average molecular weight ranging from 2270 to 49 500 g mol^?1. In Raman spectra the ratios of D‐band to G‐band intensity were similar for all of the polystyrene‐grafted samples and for the starting SWCNTs. Numerous near‐infrared electronic transitions of the SWCNTs were retained after polymer grafting. Transmission electron microscopy images showed bundles of SWCNT‐g‐PS of various diameters with some of the polystyrene clumped on the bundle surfaces. Composites of SWCNT‐g‐PS in a commercial‐grade polystyrene were prepared by precipitation of mixtures of the components from NMP into water, i.e. the coagulation method of preparation. Electrical conductivities of the composites were about 10^?15 S cm^?1 and showed no percolation threshold with increasing SWCNT content. The glass transition temperature (T_g) of the composites increased at low filler loadings and remained constant with further nanotube addition irrespective of the length and number of grafted polystyrene chains. The change of heat capacity (ΔC_p) at T_g decreased with increasing amount of SWCNT‐g‐PS of 2850 g mol^?1, but ΔC_p changed very little with the amount of SWCNT‐g‐PS of higher molecular weight. The expected monotonic decrease in ΔC_p coupled with the plateau behavior of T_g suggests there is a limit to the amount that T_g of the matrix polymer can increase with increasing amount of nanotube filler. Copyright © 2012 Society of Chemical Industry     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Study on thermal enhancement mechanism of POSS‐containing hybrid nanocomposites and relationship between thermal properties and their molecular structure

In this study, a series of poly(4‐acetoxystyrene) (PAS)‐octavinyl polyhedral oligomeric silsesquioxane (POSS) blends and the polystyrene (PS)‐octavinyl POSS blends were prepared by the solution‐blending method and characterized with Fourier transform infrared (FTIR), X‐ray diffraction (XRD), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) techniques. The results show that the glass‐transition temperature (T_g) of the PAS‐POSS blends increases at a relatively low POSS content and then decreases at a relatively high POSS content. POSS can effectively improve the thermal stability of the PAS‐POSS blends at low POSS content, and T_g of PAS‐POSS blends decreases with the increase in POSS content at relatively high POSS content. However, the T_g of the PS‐POSS blends persistently decreases even at very low POSS content. T_g change mechanism was investigated in detail by XRD, TEM, and FTIR spectra. The influence mechanism of POSS content and dispersion in composites, and parent polymer structure on thermal properties of the blends was investigated in detail. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of composition and component structure on thermal behavior and miscibility of polypropylene catalloys

The thermal behavior and the miscibility of an in‐situ polypropylene blend named polypropylene catalloys (PP‐cats) were investigated by using modulated differential scanning calorimeter (MDSC). It is found that all PP‐cats samples present two glass transitions, one of which is ascribed to the ethylene‐propylene random copolymer (EPR), and the other, to isotactic polypropylene (PP). However, no glass transition of ethylene‐propylene block copolymer (E‐b‐P) responsible for a third component in PP‐cats could be found. With the increase of EPR, the glass transition temperatures responding to PP and EPR components, T_g, _PP and T_g, _EPR, shift to low temperature, because of the enhancement of the interaction between PP and EPR component and the increase of ethylene content in EPR, respectively. Furthermore, the difference between T_g, _PP and T_g, _EPR remarkably decreases with the increase of the total ethylene content in PP‐cats, which indicates that the miscibility of PP‐cats is strongly dependent on the composition. Comparing the T_g, _PP and T_g, _EPR with T_g of fractionated PP and EPR, we ascribe the T_g change of PP fraction to the increase of EPR content; while that of EPR, to the increase of ethylene content in EPR. These experimental results suggest that the existence of E‐b‐P plays an important role in improving the miscibility between propylene homopolymer and EPR in PP‐cats. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Development and characterization of reactively extruded PVC/polystyrene blends

PVC/PS blends are obtained through a reactive extrusion–polymerization method by the absorption of a solution of styrene monomer, initiator, and a crosslinking agent in commercial suspension‐type porous polyvinyl chloride (PVC) particles, forming a dry‐blend with a relatively high monomer content. These PVC/styrene dry‐blends are reactively polymerized in a twin‐screw extruder in the melt state. They do not contain monomer residues as detected by GC. The transparency, fracture surface morphology, thermal stability, rheology and static and dynamic mechanical properties of these blends are compared to physical PVC/PS blends at similar compositions. Owing to the high polymerization temperature (180°C), short PS chains are formed in the reactive extrusion process. These short chains are dispersed both as a separate phase of ～2 μm particles (recognized by SEM) and also as molecularly dispersed chains enhancing plasticization and compatibilization. The molecularly dispersed short PS chains tend to plasticize the PVC phase, reducing its melt viscosity and glass transition temperature. The content of the short PS chains forming the dispersed separate PS particles is too low for DMTA to detect a separate T_g. Thus, reactively extruded PVC/PS blends exhibit single T_g transitions at lower temperatures compared with the neat PVC. Migration of the PVC's low‐molecular‐weight additives (lubricants and thermal stabilizer) to the PS phase is observed in the physical PVC/PS blends, causing antiplasticization of the PS phase. This results in both reduction of the T_g and an increase in the thermal stability of the PS phase in the physical PVC/PS blends. Comparing TGA thermograms of reactively extruded and physical PVC/PS indicates that the PS formed in the extruder is different from the commercial PS. This can stem from various chemical reactions that can take place in the studied reactive polymerization process. Polym. Eng. Sci. 44:1473–1483, 2004. © 2004 Society of Plastics Engineers.     

Miscibility evolution of polycarbonate/polystyrene blends during compounding

The miscibility evolution of polycarbonate/polystyrene (PC/PS) blends during the compounding process in three blending methods of industrial relevance, namely melt blending, remelt blending in a twin‐screw extruder and third melt blending in an injection molding machine, was investigated by measuring their glass transition temperatures (T_g) and their specific heat increment (ΔC_p). Differential scanning calorimetry (DSC) was used to examine nine blend compositions. Shifts in glass transition temperature (T_g) of the two phases in melt‐mixed PC/PS blends suggest partial miscibility of one polymer in the other. The observed solubility strongly depends on blend composition and blending method. The T_g measurements showed maximum mutual solubility around 50/50 composition. The miscibility of PC/PS blended after the third stage (melt injection molding) was higher than that after the first stages (melt extrusion) and the second stages (remelt extrusion).     

Modified chlorinated polypropylene as a polymer fire retardant additive in polyhydrocarbons

Partly modified chlorinated polypropylene (CPP) with dimethyl phosphonate side groups was prepared by reacting trimethyl phosphites and CPP at 115°C (Arbuzov type reaction). Products having different phosphorus and chlorine content were obtained, and the reduction of number-average molecular weight M?_n with the extent of the degree of substitution was studied. The dimethyl phosphonate groups incorporated were studied by IR spectroscopy (P? O? C at 9.6 μ and P → O at 8 μ). All products had a yellow color that may be attributed to double bond formation caused by a side dehydrochlorination reaction. Some differences of thermal stability were observed from the DSC and TGA thermograms, and no significant T_g value changes between phosphorylated products and CPP were indicated in the thermomechanical spectra. The flame retardancy of the phosphorylated products and the blends obtained by the addition of partly phosphorylated CPP to polyhydrocarbons such as polyethylene (PE), polypropylene (PP), and polystyrene (PS) was studied using the oxygen index test. The flame retardancy of these blends was compared with the flammability of the same polyhydrocarbons containing CPP. From this comparison it is concluded that the partly phosphorylated CPP is more effective as a flame retardant additive for PE, PP, and PS than itself.     

Rheology,morphology, and mechanical properties of reactive compatibilized polypropylene/polystyrene blends via Friedel–Crafts alkylation reaction in the presence of clay

Attempts were made to study the effect of reactive compatibilization via Friedel–Crafts alkylation reaction, using AlCl₃ as a catalyst, on rheology, morphology, and mechanical properties of polypropylene/polystyrene ( PP/PS) blends in the presence of an organoclay (Cloisite 15A). During the reactive compatibilization process, PS showed much more degradation than that of PP in the presence of AlCl₃. It was found that the effect of generation of PP‐g‐PS copolymer at the interface of the PP/PS blend dominates the effects of degradation of PS and PP phases, which manifested itself by increased toughness as well as uniform dispersion of the dispersed PS particles in the PP matrix. Generation of PP‐g‐PS copolymer was confirmed by using Fourier‐transform infrared analysis. By using rheological and X‐ray diffraction analyses, it was shown that the clay had higher affinity to PS than that of PP. It was also shown that the clay located at the interface of PP and PS phases, leading to increased relaxation time of the deformed PS dispersed particles, exhibited higher dispersion in PP/PS blend, which resulted in higher ductility of the blend. By using the results of rheological studies, it was concluded that during reactive compatibilization of the blend nanocomposite, the clay migrated into the dispersed PS phase, which was confirmed by scanning electron microscopy analysis. It was demonstrated that the rheological studies have a reliable sensitivity to the clay partitioning and phase morphology of the studied blends and blend nanocomposites . J. VINYL ADDIT. TECHNOL., 24:18–26, 2018. © 2015 Society of Plastics Engineers     

Blast furnace slags as functional fillers on rheological,thermal, and mechanical behavior of thermoplastics

Blast furnace slags (BFS) is a secondary byproduct of iron industry, which has a combination of acidic and basic oxides and show a complex, multiphase structure. If appropriately tailored, BFS could be an effective functional filler, improving the property profile of thermoplastics such as polypropylene (PP) and polystyrene (PS). As a raw material, the proposed filler may introduce both economic and ecological advantages, as it is considered an inexpensive secondary product rather than a natural resource. The current study aims at investigating the effect of incorporating BFS as a micro‐sized filler on the rheological, thermal, and mechanical behavior of PP and PS. BFS types in this study are air‐cooled, crystalline, and amorphous, grounded types. Both types are ground into 71, 40, and 20 μm batches and introduced in 10, 20, and 30 weight fractions via melt kneading. Mixtures are then formed into 4‐mm and 2‐mm thick plates via compression molding. Slight increase in rheological factors is observed with increasing filler loading. BFS hinders the crystallization of PP, resulting in slight increase of crystallization temperatures (T_c) and lowering of crystallization enthalpy (ΔH_c). No significant effect of filler on transition temperatures (T_g) is reported. Mechanically, BFS increases the tensile modulus of PP, but decreases its strength. For PS formulations, a modest toughening effect is observed by slag filler. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43021.     

Morphology,crystallization, and thermal behavior of isotactic polypropylene/polystyrene blends: Effects of the addition of a graft copolymer of propylene with styrene

Optical microscopy, differential scanning calorimetry, and small‐angle X‐ray scattering techniques were used to study the influence of crystallization conditions on the morphology and thermal behavior of samples of ternary blends constituted by isotactic polypropylene (iPP), atactic polystyrene (aPS), and a novel graft copolymer of unsaturated propylene with styrene (uPP‐g‐PS) with the purpose of assessing the uPP‐g‐PS capability to act as a compatibilizer for iPP/aPS materials. It was shown that the presence of the uPP‐g‐PS copolymer affects the interfacial tension between the iPP and aPS phases in the melt state, with the aPS particle size and the particle‐size distribution being, in fact, strongly modified. In samples of iPP/aPS/uPP‐g‐PS blends, isothermally crystallized from the melt at a relatively low undercooling in a range of the crystallization temperature of the iPP phase, the addition of the uPP‐g‐PS copolymer induced a drastic change both in the aPS mode and the state of dispersion and in the iPP spherulitic texture and inner structure of the spherulite fibrils. In particular, the phase structure developed in the iPP/aPS/uPP‐g‐PS materials was characterized by a crystalline lamellar thickness of the iPP phase comparable to that shown by the plain iPP. The extent of the induced modifications, that is, the degree of compatibilization achieved, resulted in a combined effect of composition and undercooling. Also, relevant thermodynamic parameters of the iPP phase, such as the equilibrium melting temperature (T_m) and the folding surface free energy (ς_e) of the lamellar crystals, were found to be influenced by the presence of the uPP‐g‐PS copolymer. A linear decrease of the T_m and ς_e values with increasing uPP‐g‐PS content was, in fact, observed. Such results have been accounted for by an increase of the presence of defects along the iPP crystallizable sequences and by the very irregular and perturbed surface of the crystals with increasing copolymer content. The observed decrease in T_m values revealed, moreover, that, in the iPP/aPS/uPP‐g‐PS blends, the iPP crystal growth occurs under comparatively lower undercooling, in line with higher crystalline lamellar thickness shown by SAXS investigation. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1429–1442, 1999     

Interfacing polypropylene/poly(BPA carbonate) blend phases with graft copolymers: Thermal and dynamic mechanical analyses

This paper presents data on the thermal, dynamic, and mechanical properties of polypropylene (PP) blends with bisphenol-A-polycarbonate (PC), to which a series of graft and block copolymers in a small quantity was added. The effect of the minor component on the crystallization and relaxation behavior of PP in the blends has been investigated and correlated with the mechanical properties obtained. The results demonstrate that the graft copolymeric additives to the blends can reduce the degree of undercooling (T_m^°C ? T_c^°C) of the PP phase. However, the block copolymers used, substituting for the graft copolymers, showed no such function. Dynamic mechanical thermal analysis (DMTA) indicates that, with the addition of several different copolymers as minor additives to the blends, two loss peaks representing the glassy transitions (T_g) of the individual components (PP and PC) were retained, with little tendency of approaching toward each other, suggesting no obvious improvement in compatibility of the PP phase and the PC phase in the blends. Nevertheless, the inclusion of different copolymers in the PP/PC blends, in spite of the small quantity used (4%), can lead to a significant mechanical property difference of the blends. This difference could be reasonably explained from the data obtained in dynamic mechanical characterization of the different graft copolymers in PP blends.