聚己内酯/胶原/丝素复合微纳米纤维膜的制备

采用静电纺丝技术制备了聚己内酯(PCL)与胶原/丝素(COL/SF)质量比为0∶100、10∶90、20∶80、30∶70、40∶60、50∶50的复合微纳米纤维膜,通过扫描电子显微镜、力学性能测试和接触角测试等对复合纤维膜的理化性能进行表征,并将HepG_2细胞种植在复合纤维膜上检测其细胞生物相容性。结果表明:PCL/COL/SF复合微纳米纤维膜纤维形貌良好,纤维直径和亲水性随PCL含量的增加而减小;PCL/COL/SF复合纤维膜具有较好的力学性能。PCL与COL/SF质量比为30∶70时,复合纤维膜亲水性良好,强度和柔性最佳,并且HepG_2细胞在复合纤维膜表面黏附生长良好,细胞增殖情况明显,表明PCL与COL/SF质量比为30∶70的复合纤维膜有望成为一种良好的载体,可应用于体外肝细胞培养。     

SA溶液浓度对乳液静电纺丝SA/PCL纳米纤维成形的影响

乳液静电纺丝可制备同时含有亲水和亲油两相结构的复合纳米纤维。以聚己内酯(PCL)/三氯甲烷为连续相,海藻酸钠(SA)/去离子水为分散相,失水山梨醇脂肪酸酯(Span80)为乳化剂,制备油包水(W/O)型乳液,并采用乳液静电纺丝技术制得SA/PCL复合纳米纤维膜,经与Ca2+置换制得海藻酸钙(CA)/PCL复合纤维膜,研究了SA溶液浓度对纤维成形的影响。结果表明:表面活性剂Span80和分散相SA水溶液的加入可有效增加PCL的可纺性;当乳液体系中SA溶液体积一定,SA溶液浓度对SA/PCL乳液的黏度无明显影响;随SA溶液浓度的增加,SA/PCL乳液的表面张力降低,SA/PCL复合纳米纤维的直径出现极大值,但均小于仅添加Span80所得的PCL纳米纤维;SA在复合纳米纤维成形过程中会向纤维表面迁移,从而可实现SA与Ca2+交换,且离子交换后形成纤维间的粘连结构。     

水性聚氨酯/聚乙烯醇复合纳米纤维的制备及结构研究

将水性聚氨酯(WPUR)与聚乙烯醇(PVAL)按照不同质量比制备质量分数为8%的纺丝溶液,通过静电纺丝制备WPUR/PVAL复合纳米纤维。运用扫描电子显微镜、傅立叶变换红外光谱仪和X射线衍射仪对WPUR与PVAL质量比不同的纺丝溶液制备的复合纳米纤维的微观形貌和结构进行分析。实验结果表明,PVAL的含量对复合纳米纤维的形成和形貌起着决定性的作用,随着溶液中PVAL含量的增加,纺丝过程中纺丝液逐渐从不连续复合纳米纤维转变为连续均匀的复合纳米纤维,纤维直径逐渐增大,当纺丝液中WPUR与PVAL的质量比为30∶70时,得到的复合纳米纤维形貌最佳,其平均直径为330.8 nm,具有最小标准差,为22 nm,同时随着纺丝溶液中PVAL含量的增加,所得复合纳米纤维的结晶性能增强。     

丝素-聚己内酯纳米纤维膜的制备工艺

以六氟异丙醇(HFIP)为溶剂,采用静电纺丝技术制备丝素(SF)-聚己内酯(PCL)复合纳米纤维膜。采用热场发射扫描电镜、Image-Pro Plus图像分析和力学拉伸的方法表征了纳米纤维膜的结构与力学性能。通过设计的三因素四水平正交试验对复合纳米纤维膜的多个指标进行了分析,采取归一化数据处理及平均权重分配的方式量化了复合纳米纤维膜的品质,确定了共混复合纳米纤维膜制备的最优工艺参数,并且采用最佳工艺参数制备了SF-PCL复合纳米纤维膜,分析了其力学性能。结果表明:在溶质质量分数为6%、溶质SF与PCL质量比为3∶2、纺丝流速1.2 mL/h时,SF-PCL复合纳米纤维膜具有较好的品质;双轴拉伸时的破坏机制与单轴不同,其断裂应力和应变只是单轴时的一半左右,膜的力学性能表现为各向同性。     

溶液参数对静电纺丝PAN@PS复合纳米纤维形貌及结构的影响

采用同轴静电纺丝技术,以聚丙烯腈(PAN)溶液为核层、聚苯乙烯(PS)溶液为壳层,制备了PAN@PS复合纳米纤维。研究了纺丝液浓度、溶剂种类对PAN@PS复合纳米纤维形貌和结构的影响。结果表明:PS/四氢呋喃(THF)作为壳层溶液的复合纳米纤维(PAN@PS/THF)可获得相界面清晰的同轴纤维。随PS纺丝液浓度的增加,纤维的直径先增大后有所减小,整体呈现递增的趋势,当PS/THF质量分数为20%时,纤维直径约为693 nm且表面光滑。而以质量分数为20%的PS/二甲基甲酰胺(DMF)为壳层溶液的复合纳米纤维(PAN@PS/DMF)直径有所增加且纤维表面凹凸不平,呈现双相连续的结构。因此,在静电纺丝过程中,可以通过改变纺丝液的参数来调节纤维的形貌和结构。     

聚己内酯/纳米氧化锌抗菌静电纺丝膜的制备及性能表征

利用静电纺丝技术制备聚己内酯（PCL）/纳米氧化锌（ZnO）超细纤维,通过扫描电子显微镜、差示扫描量热仪研究了静电纺丝电压和ZnO用量对复合纤维的直径、热性能和结晶性能的影响,并通过抗菌实验研究了PCL/ZnO复合纤维膜的抗菌性能。结果表明,随着纺丝电压的升高,PCL的直径先减小后增加,熔点（Tm）和片晶厚度（Lc）呈现先增加后减小的趋势;随着ZnO用量的增加,PCL/ZnO复合纤维的直径在不同电压下均逐渐增加,Tm和结晶度（Xc）也逐渐增加;当ZnO的含量为2.0 %时抗菌性能最强,并在放置60 d后抗菌性能依旧没有明显下降。     

静电纺丝复合滤材制备及性能研究

研究了纺丝液浓度对聚丙烯腈(PAN)静电纺丝纤维直径,以及对PAN静电纺丝纳米纤维膜复合滤材过滤性能的影响。测试结果表明,纺丝液浓度增加,静电纺丝纤维直径变粗,孔径增大,其中质量分数为16%的纺丝液具有良好的纺丝性能,静电纺丝所得的纳米纤维直径均匀,复合后滤材在颗粒直径0.3μm,过滤风速5.3 cm/s的测试条件下,过滤效率达到99.98%,阻力为138 Pa,达到H13级别,具有高效低阻特性。     

静电纺丝技术制备ETPE基多元含能复合纤维

为了探索ETPE基多元含能复合纤维的静电纺丝制备工艺,以聚叠氮缩水甘油醚基热塑性弹性体(GAP-ETPE)为聚合物黏合剂,CL-20、纳米铝粉(n-Al)作为高能组分,采用静电纺丝技术制备了GAP-ETPE基超细含能复合纤维,并对溶剂、前驱液质量分数、固相组分配比等关键工艺参数进行了优化;采用扫描电子显微镜(SEM)和透射电子显微镜(TEM)对产物形貌进行了表征,采用DSC法分析了复合纤维的热分解性能;测试了复合纤维的机械感度。结果表明,GAP-ETPE基含能复合纤维静电纺丝制备最佳溶剂为丙酮,产物成丝均匀、表面光滑;在GAP-ETPE/CL-20质量比为3∶7、前驱液质量分数为50%时,二元超细含能复合纤维(CL_x-ETPE_y-Z)的成丝效果最优,平均直径约为2480nm;在铝粉质量分数为10%、前驱液质量分数为50%时,三元超细含能复合纤维(CL-Al_m-ETPE-Z)的成丝效果最优,平均直径约为930nm;相比于CL-20,CL₇-ETPE₃-50含能复合纤维热分解峰值温...     

PVP/PEO复合微纳米纤维的电纺性研究

采用聚乙烯毗咯烷酮/聚氧化乙烯/水(PVP/PEO/H2O)体系进行静电纺丝制备PVP/PEO复合微纳米纤维,研究了PVP/PEO共混溶液浓度、PVP相对分子质量及PVP:PE0(质量比)对PVP静电纺丝的影响.结果表明:当溶液质量分数增大到15%、PVP相对分子质量为1.3×106或PEO含量增大时,均可制得形貌清晰、表面光滑的微纳米纤维.当PVP/PEO溶液质量分数为12%、PVP相对分子质量为1.3 × 106及PVP:PE0(质量比)为8:2时,静电纺丝所得纤维形貌最佳.     

静电纺Co/C有序纳米纤维的制备及其吸波性能

采用静电纺丝法结合滚筒收集装置制备了有序排列的Co/C复合纳米纤维。通过X射线衍射(XRD)仪、扫描电子显微镜(SEM)、矢量网络分析仪(VNA)对复合纳米纤维的物相、微观结构、电磁参数进行表征,并对其微波吸收性能进行研究。结果表明:经后期热处理复合纳米纤维由无定型碳和面心立方结构的金属Co纳米粒子组成。滚筒表面线速度对纤维的微观形貌影响较大,随着滚筒表面线速度的增加,复合纳米纤维的有序度逐渐提高。当滚筒表面线速度为5.0 m/s,涂层厚度为2.0 mm时,有效吸收带宽达到最大5.1 GHz,相比于无序纤维吸波性能得到显著提升。     

改性氧化铈/钨酸镍环氧防腐涂层的制备及性能

采用水热法制备出不同质量比的氧化铈/钨酸镍(CeO₂/NiWO₄)的复合粒子,再选用硅烷偶联剂KH560对其进行改性,利用傅里叶变换红外光谱（FTIR）、X射线衍射（XRD）和扫描电子显微镜（SEM）表征了复合粒子的结构与形貌。将改性的复合粒子分散于环氧树脂（EP）中,然后喷涂在碳钢基体上制备CeO₂/NiWO₄/EP复合涂层,利用电化学交流阻抗（EIS）、加速浸泡实验和摩擦磨损试验（Taber）测试涂层的防腐与摩擦性能。结果表明：添加CeO₂/NiWO₄复合粒子的环氧树脂涂层的防腐耐磨性能大幅度提高,而且当复合粒子中CeO₂与NiWO₄的质量比为4∶3时,涂层防腐耐磨性能最好,该复合环氧涂层在3.5%NaCl水溶液中浸泡后期(45天)仍保持较高的阻抗模量(7.36×10⁸ Ω/cm²),比纯环氧树脂涂层高一个数量级。同时,经过10000转摩擦磨损后,此复合涂层的质量损失较纯环氧涂层减少56%,厚度损失量仅为CeO₂/EP的50%,表现出最优异的防腐耐磨性能。     

Epoxy coating with self-healing capability based on a 2-mercaptobenzothiazole-loaded CeO2 nanocontainer

In this study, we demonstrated a facile approach for the synthesis of nanocontainers using the encapsulation of a 2-mercaptobenzothiazole (MBT) inhibitor; these nanocontainers were capable of responsively releasing a corrosion inhibitor and of self-healing performances. The anticorrosive performance of the CeO₂ nanocontainers was investigated with electrochemical impedance spectroscopy (EIS) measurement in a saline electrolyte via the incorporation of different weight percentages (0.5, 1, and 2 wt %) of synthesized nanocontainer in epoxy (EP) resin. The EIS results show that the loading of 1 wt % CeO₂ nanocontainer containing MBT inhibitor in the epoxy (EP) coating [EP/NC MBT–CeO₂ (1%)] provided the highest R_coat, the lowest constant phase element of coating, and the optimum release of MBT at different operating pHs. The highest coating resistance R_coat values of this coating (7.81 × 10⁷ Ω cm²) were about 12 and 8573 times greater than those considered for EP–CeO₂ and EP coatings, respectively. Different releases of the MBT inhibitor were detected at various pHs. We found that the coating operating in acidic media exhibited a better self-healing performance. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47297.     

Synergic enhancement of the anticorrosion properties of an epoxy coating by compositing with both graphene and halloysite nanotubes

The aim of this research was to improve the corrosion resistance of metal surfaces with polymer coatings. Both graphene and halloysite nanotubes (HNTs) were introduced together into the epoxy resin coating for the enhanced barrier protection of the metallic surface. The anticorrosion behaviors of different coatings were comparatively evaluated by the potentiodynamic polarization curves, electrochemical impedance spectroscopy (EIS), and neutral salt spray (NSS) tests. The potentiodynamic polarization curves showed that the coating containing 0.5 wt % HNTs and 0.8 wt % graphene (H05G08EP) together had the most positive corrosion potential and the minimum corrosion current density. The EIS results revealed that graphene endowed the composite coatings with excellent electrochemical performance for anticorrosive purposes. The NSS tests indicated that H05G08EP endured the longest NSS time. These results suggest that H05G08EP had the best corrosion resistance. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47562.     

镀液中TiO2对（Ni-W-P）-TiO2复合镀层性能的影响

为了进一步提高Ni-W-P合金镀层的硬度和耐蚀性,用脉冲电沉积法制备了(Ni-W-P)-TiO2复合镀层,并研究了镀液中TiO2加入量对镀层硬度和表面形貌的影响,且通过极化曲线和电化学阻抗谱研究了镀层在3.5%NaCl溶液中的耐蚀性能。结果表明,(Ni-W-P)-TiO2复合镀层的性能优于Ni-W-P镀层,而当镀液中TiO2质量浓度为6g/L时,复合镀层的硬度较高,表面形貌及耐蚀性能较优。自腐蚀电位较正,腐蚀电流密度较小,极化电阻较大,其交流阻抗谱对应的电阻值也较大。     

Preparation of polyvinylpyrrolidone/graphene oxide/epoxy resin composite coatings and the study on their anticorrosion performance

Waterborne epoxy resin (EP) is often used as anticorrosive coating in the industrial field. However, small holes and gaps can be formed during the curing process. The corrosive medium easily penetrates the anticorrosive coating and corrodes the metal matrix. Herein, polyvinylpyrrolidone (PVP) and graphene oxide (GO) were doped into EP to improve the shielding and resistance to corrosive media. The composite coatings were prepared successfully by solution blending method. In the PVP/GO composite materials, original spatial structure of GO was changed and the composite was mainly combined by covalent bonding. The surface morphology of hybrid filler was flat and uniform, and the structural defects of GO was reduced. Compared with single-layer anticorrosive coating, the corrosion potential of PVP/GO/EP coating moved forward and the corrosion current density decreased. The ideal corrosion resistance of PVP/GO/EP composite coatings was mainly because agglomeration of GO sheet was obviously avoided after it was modified by PVP. Furthermore, the hybrid filler can be uniformly dispersed in the aqueous EP. It blocked the gaps and holes inside the coatings, which could contribute to form anticorrosive coatings.     

Mica/polypyrrole (doped) composite containing coatings for the corrosion protection of cold rolled steel

Micas/polypyrroles (PPys) doped with molybdate, p-toluene sulfonate, dodecyl benzene sulfonate, and 2-naphthalene sulfonate composite pigments were synthesized by chemical oxidative polymerization and characterized in coatings for corrosion protection on cold rolled steel substrate by various electrochemical techniques. Synthesized composite pigments were characterized for morphology by scanning electron microscopy, which indicated physical formation of PPy on the surface of mica. Chemical composition of the composite pigments was analyzed by X-ray photoelectron spectroscopy which chemically confirmed doped PPy formation on the mica surface. Coatings were formulated at 20% pigment volume concentration (composite pigments or as-received mica pigment) and were applied on cold rolled steel substrate. Coatings were exposed to salt spray test conditions (ASTM B117) for 30 days and were periodically assessed for corrosion with electrochemical impedance spectroscopy (EIS), open circuit potential (OCP), and potentiodynamic polarization. EIS and circuit modeling results demonstrated higher coating resistance (R _c) for mica/PPy (doped) composite coatings as compared to as-received mica pigment containing coating after 30 days of salt spray exposure. Lower current density and more positive corrosion potential values were observed for mica/PPy (doped) composite coatings as compared to mica pigment-based coating in potentiodynamic polarization measurements, indicating improved corrosion protection for cold rolled steel substrate. OCP measurements revealed more positive values for mica/PPy (doped) composite coatings as compared to mica pigment-based coating suggesting superior corrosion protection for mica/PPy (doped) composites.     

水分散性聚苯胺/环氧树脂乳液防腐蚀涂层研究

利用原位插层聚合方法制备了水分散性的聚苯胺/蒙脱土复合材料(PANI/MMT),对其结构进行了XRD表征,测试了变温电导率;并以水性环氧树脂乳液为成膜物,制备了水分散性聚苯胺/环氧树脂乳液复合防腐蚀涂层材料(PANI/MMT/EP),通过开路电位(OCP)、电化学交流阻抗谱(EIS)和塔菲尔曲线(Tafel)对其性能进行了研究,结果表明,PANI/MMT/EP复合涂层对A3钢具有较好的防腐蚀效果,腐蚀电流降低到10-9.7A/cm2。     

Antibacterial activity and corrosion resistance of Ta2O5 thin film and electrospun PCL/MgO-Ag nanofiber coatings on biodegradable Mg alloy implants

Biodegradable magnesium (Mg) alloys have drawn considerable attention for use in orthopedic implants, but their antibacterial activity and corrosion resistance still require improvement. In the present work, functional Ta₂O₅ (tantalum pentoxide) compact layers and PCL/MgO-Ag (poly (ε-caprolactone)/magnesium oxide-silver) nanofiber porous layers were subsequently deposited on Mg alloys via reactive magnetron sputtering and electrospinning, respectively, to improve anticorrosion and antibacterial performance. Sputter coating of the Ta₂O₅ resulted in a thick layer (～1?μm) with an amorphous structure and high adhesive strength. The nanostructure exhibited bubble-like patterns with no obvious nano-cracks, nano-porosities, or pinholes. The electrospun PCL/MgO-Ag nanofiber coating was porous, smooth, and plain with no obvious beads. In vitro corrosion tests demonstrated the PCL/MgO-Ag nanofiber-coated alloy had greater corrosion resistance than a Ta₂O₅ sputter-coated alloy or uncoated Mg alloy. The additional electrospun PCL/MgO-Ag nanofiber coating also had greater antibacterial behavior toward Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus) bacteria than the Ta₂O₅-coated or uncoated alloy specimens. Increasing the MgO-Ag concentration of the nanofibers from 1 to 3?wt% increased antibacterial activity. The combination of Ta₂O₅ and PCL/MgO-Ag nanofiber coatings on Mg alloys may therefore have potential applications for reducing bone infection as related to orthopedic implants for bone repair.     

Anticorrosion behavior of cyclodextrins/inhibitor nanocapsule-based self-healing coatings

The self-healing anticorrosion property of coating containing cyclodextrins/inhibitor nanocontainers was investigated by SEM, TEM, salt spray, and EIS measurements. The influences of cyclodextrin type (α-CD, β-CD and γ-CD) and nanocapsules diameter on the anticorrosive performance of the scratched samples were studied under salt spray conditions, which revealed that the coatings containing γ-CD/inhibitor nanocontainers with larger nanocapsules at room temperature demonstrated the best anticorrosion behavior. Inclusion complex formation of MBI or MBT with CDs led to encapsulated corrosion inhibitors which became active in corrosive electrolytes, and could slowly diffuse out of the host material to ensure continuous delivery of the inhibitors to corrosion sites and long-term corrosion protection. Additionally, the kinetics of the self-healing process characterized by EIS measurement was parametrically analyzed in an equivalent circuit when the coating was exposed to salt solution.