Highly selective sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene)/poly(ether sulfone) blend proton exchange membranes for direct methanol fuel cells

Proton exchange membranes (PEMs) based on blends of poly(ether sulfone) (PES) and sulfonated poly(vinylidene fluoride‐co‐hexafluoropropylene) (sPVdF‐co‐HFP) were prepared successfully. Fabricated blend membranes showed favorable PEM characteristics such as reduced methanol permeability, high selectivity, and improved mechanical integrity. Additionally, these membranes afford comparable proton conductivity, good oxidative stability, moderate ion exchange capacity, and reasonable water uptake. To appraise PEM performance, blend membranes were characterized using techniques such as Fourier transform infrared spectroscopy, AC impedance spectroscopy; atomic force microscopy, and thermogravimetry. Addition of hydrophobic PES confines the swelling of the PEM and increases the ultimate tensile strength of the membrane. Proton conductivities of the blend membranes are about 10^?3 S cm^?1. Methanol permeability of 1.22 × 10^?7cm² s^?1 exhibited by the sPVdF‐co‐HFP/PES10 blend membrane is much lower than that of Nafion‐117. AFM studies divulged that the sPVdF‐co‐HFP/PES blend membranes have nodule like structure, which confirms the presence of hydrophilic domain. The observed results demonstrated that the sPVdF‐co‐HFP/PES blend membranes have promise for possible usage as a PEM in direct methanol fuel cells. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43907.     

Synthesis of a poly(methyl methacrylate)‐b‐poly[2‐(N,N‐dimethylamino) ethyl methacrylate] block copolymer and its effects on the surface charges and pH‐responsive properties of poly(vinylidene fluoride) blend membranes

A poly(methyl methacrylate) (PMMA)‐b‐poly[2‐(N,N‐dimethylamino) ethyl methacrylate] (PDMAEMA) block copolymer was successfully synthesized by a reversible addition–fragmentation chain‐transfer method. The resulting copolymer was used to prepare poly(vinylidene fluoride) blend membranes via a phase‐inversion technique. The polymorphism, structure, and properties of the blend membranes were investigated by Fourier transform infrared spectrometry, scanning electron microscopy (SEM), ζ potential analysis, and filtration. The results indicate that PMMA‐b‐PDMAEMA could migrate onto the surface of the membrane during the coagulation process, and more of the β‐crystal phase appeared with the increase of the block copolymer in the membranes. The surface morphology and cross section of the membranes were also affected by the copolymer, as shown by SEM. The ζ‐potential results show that the surface charges of the membrane could be changed from positive to negative at an isoelectric point as the pH increased. The blend membrane also exhibited good pH sensitivity, and its water flux showed a great dependence on pH. The filtration experiment also indicated that the blend membrane had good hydrophilicity and antifouling properties. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40685.     

Radiational hardening of poly(vinylidene fluoride)–poly(methyl methacrylate)–polystyrene ternary blends

Specimens of poly(vinylidene fluoride) (PVDF)–poly(methyl methacrylate) (PMMA)–polystyrene (PS) polyblends with different weight percentage ratios of the three polymers were prepared with the solution cast technique. The effect of γ irradiation on the Vicker's microhardness was studied. Among the three pure polymers, PVDF, PMMA, and PS, the γ irradiation imparted crosslinking in PVDF, thereby causing radiational hardening. In the cases of PMMA and PS, the effect of irradiation exhibited a predominance of both the scissioning and crosslinking processes in different ranges of doses. Moreover, at a dose of 5 Mrad, in both PMMA and PS, maximum radiational crosslinking was observed. The effect of γ irradiation seemed to stabilize beyond 15 Mrad in PVDF and beyond 20 Mrad in PMMA and PS. Microhardness measurements on ternary blends of PVDF, PMMA, and PS revealed that the blend with low contents of PMMA, that is, up to 5 wt %, yielded softening, whereas increasing the content of PMMA beyond 5 wt % produced a hardened material because of radiational crosslinking, and a higher content of PMMA in the blend facilitated this crosslinking. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3107–3111, 2004     

Compatibilization of polypropylene/polystyrene blends with poly(styrene-b-butadiene-b-styrene) block copolymer

The compatibilizing effect of the triblock copolymer poly(styrene-b-butadiene-b-styrene) (SBS) on the morphology and mechanical properties of immiscible polypropylene/polystyrene (PP/PS) blends were studied. Blends with three different weight ratios of PP and PS were prepared and three different concentrations of SBS were used for investigations of its compatibilizing effects. Scanning electron microscopy (SEM) showed that SBS reduced the diameter of the PS-dispersed particles as well as improved the adhesion between the matrix and the dispersed phase. Transmission electron microscopy (TEM) revealed that in the PP matrix dispersed particles were complex “honeycomblike” aggregates of PS particles enveloped and joined together with the SBS compatibilizer. Wide-angle X-ray diffraction (WAXD) analysis showed that the degree of crystallinity of PP/PS/SBS slightly exceeded the values given by the addition rule. At the same time, addition of SBS to pure PP and to PP/PS blends changed the orientation parameters A₁₁₀ and C significantly, indicating an obvious SBS influence on the crystallization process in the PP matrix. SBS interactions with PP and PS influenced the mechanical properties of the compatibilized PP/PS/SBS blends. Addition of SBS decreased the yield stress and the Young's modulus and improved the elongation at yield as well as the notched impact strength in comparison to the binary PP/PS blends. Some theoretical models for the determination of the Young's modulus of binary PP/PS blends were used for comparison with the experimental results. The experimental line was closest to the series model line. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 69: 2625–2639, 1998     

Synthesis and characterization of poly(vinyl alcohol)‐based membranes for direct methanol fuel cell

Membranes made of poly(vinyl alcohol) (PVA) and its ionic blends with sodium alginate (SA) and chitosan were synthesized and characterized for their ion-exchange capacity (IEC) and swelling index values to investigate their applicability in direct methanol fuel cells (DMFCs). These membranes were assessed for their intermolecular interactions, thermal stabilities, and mechanical strengths with Fourier transform infrared spectroscopy, X-ray diffraction methods, differential scanning calorimetry, thermogravimetric analysis, and tensile testing, respectively. Methanol permeability and proton conductivity were also estimated and compared to that of Nafion 117. In addition to being effective methanol barriers, the membranes had a considerably high IEC and thermal and mechanical stabilities. The addition of small amounts of anionic polymer was particularly instrumental in the significant reduction of methanol permeability from 8.1 × 10⁻⁸ cm²/s for PVA to 6.9 × 10⁻⁸ cm²/s for the PVA–SA blend, which rendered the blend more suitable for a DMFC. Low methanol permeability, excellent physicomechanical properties, and above all, cost effectiveness could make the use of these blends in DMFCs quite attractive. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1154–1163, 2005     

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) copolymer on the properties of polylactide/poly(methyl methacrylate) blend

The effect of the addition of poly(styrene‐co‐glycidyl methacrylate) P(S‐co‐GMA) copolymer on the properties of melt blended polylactide/poly(methyl methacrylate) (PLA/PMMA) 80/20 (wt %) composition was studied. In the literature high ductility levels were achieved by melt blending PLA with different additives. However, the gained ductility was counter balanced with drastic drops in strength and modulus values. The novelty of this work was the preparation of PLA‐based blends with polylactide content higher than 75 wt % which showed an impact resistance value improvement of about 60% compared with the neat PLA and maintained similar tensile strength and modulus values as well as glass transition temperature to neat PLA. The addition of only 3 pph of copolymer to PLA/PMMA blend improved the impact resistance almost 100%. The chemical reaction between PLA/PMMA blend and P(S‐co‐GMA) copolymer were analyzed by FTIR, rotational rheometry, and GPC/SEC. Phase structure and morphology were studied by Differential Scanning Calorimetry and Scanning Electronic Microscopy. Tensile and impact properties as well as thermal stability were also studied. Results showed that as the amount of copolymer in the blend was increased then higher was average molecular weight and polydispersity index. After the addition of P(S‐co‐GMA) copolymer to the PLA/PMMA blend the impact resistance, elongation at break and thermal stability were improved while tensile strength and elastic modulus remained almost unaltered. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43935.     

Sulfonated polyether sulfone‐poly(vinylidene fluoride) blend membrane for DMFC applications

Direct methanol fuel cell (DMFC) proton exchange membranes were prepared by blending poly (vinylidene fluoride) (PVDF) with sulfonated poly(ether sulfone) (SPES). Using a diffusion cell and gas chromatographic technique, the effects of PVDF content on methanol permeability in the blended membranes were investigated. The thermal resistance and proton conductivity of the membranes were also determined by using a thermal gravimetric analysis (TGA) and an impedance analysis technique respectively. The presence of sulfonic acid groups in SPES was confirmed by Fourier transform infrared (FTIR). It was found that the methanol permeability in the blended membranes decreased with PVDF content at the expense of proton conductivity. Blended membranes show methanol permeability values much lower than that of Nafion 115, whereas the proton conductivities of the membranes are comparable with that of Nafion. The thermal stability of these blended membranes is above 250°C, which is sufficiently high for use in DMFC. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Amphiphilic poly(vinyl chloride)‐g‐poly[poly(ethylene glycol) methylether methacrylate] copolymer for the surface hydrophilicity modification of poly(vinylidene fluoride) membrane

In this study, a comblike amphiphilic graft copolymer containing poly(vinyl chloride) (PVC) backbones and poly(oxyethylene methacrylate) [poly(ethylene glycol) methylether methacrylate (PEGMA)] side chains was facilely synthesized via an atom transfer radical polymerization method. Secondary chlorines in PVC were used as initial sites to graft a poly[poly(ethylene glycol) methylether methacrylate] [P(PEGMA)] brush. The synthesized PVC‐g‐P(PEGMA) graft copolymer served as an efficient additive for the hydrophilicity modification of the poly(vinylidene fluoride) (PVDF) membrane via a nonsolvent‐induced phase‐inversion technique. A larger pore size, higher porosity, and better connectivity were obtained for the modified PVDF membrane; this facilitated the permeability compared to the corresponding virgin PVDF membrane. In addition, the modified PVDF membrane showed a distinctively enhanced hydrophilicity and antifouling resistance, as suggested by the contact angle measurement and flux of bovine serum albumin solution tests, respectively. Accordingly, the PVC‐g‐P(PEGMA) graft copolymer was demonstrated as a successful additive for the hydrophilicity modification, and this study will likely open up new possibilities for the development of efficient amphiphilic PVC‐based copolymers for the excellent hydrophilicity modification of PVDF membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Ion‐exchange membranes prepared by blending sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) with polybenzimidazole

New ion‐exchange acid/base‐blend (SPPO/PBI) membranes were prepared by mixing N,N‐dimethylacetamide (DMA) solutions of sulfonated poly(2,6‐dimethyl‐1,4‐phenylene oxide) (SPPO) in the ammonium form and of polybenzimidazole (PBI), casting the solution as a thin film, evaporating the solvent, and treating the membrane with aqueous hydrochloric acid. The resulting membranes were found insoluble in DMA. The preliminary tests of the membranes were carried out in an H₂/O₂ fuel cell at room temperature. Their performance in the fuel cell increased with the increase in the concentration of SPPO sulfonic acid groups in the blend, but the membranes formed with the highly sulfonated SPPO alone or predominanting, which swelled excessively in water, did not give reproducible results, and their performance was usually inferior to that of the membranes having an optimum ratio of both components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1118–1127, 2002     

Methanol permeability and proton conductivity of direct methanol fuel cell membranes based on sulfonated poly(vinyl alcohol)–layered silicate nanocomposites

Layered silicate nanocomposite membranes to be used as electrolyte polymeric membranes in a direct methanol fuel cell were prepared through the mixing of poly(vinyl alcohol) (PVA) with various amounts (2, 4, and 5% w/w) of sodium montmorillonite layered silicate nanoclay. The proton conductivity of the polymer was induced by the reaction of the polymer with sulfosuccinic acid. After that, a solution of the sulfonated PVA–layered silicate nanocomposite was cast into membranes. The proton conductivity and methanol permeability of the membranes were determined with a four-point probe technique and a gas chromatography technique, respectively. In addition, structures of the nanocomposite membranes were characterized with X-ray diffraction, differential scanning calorimetry, and Fourier transform infrared techniques. The mechanical properties of the nanocomposite membranes were also determined with a universal testing machine. From the results, it was found that the water uptake, proton conductivity, and methanol permeability of the membranes initially decreased after a 2% (w/w) concentration of the layered silicate was added. Above this nanoclay loading, the water uptake of the membranes increased again. The results were examined in the light of the interaction between the clay and sulfonated polymer, and the steric effect provided the exfoliation of the nanoclay. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Reactive compatibilization of polystyrene/poly(ethylene–co–vinyl acetate) (EVA) blends

A reactive compatibilizer, mercapto‐functionalized EVA (EVASH), in combination with styrene‐butadiene block copolymer (SBS), was used to compatibilize the blends of polystyrene (PS) and ethylene–vinyl acetate copolymer (EVA). The reactive compatibilization was confirmed by the presence of insoluble material and from dynamic‐mechanical analysis. In addition to a more uniform morphology with small phase size, the compatibilization also provided excellent stabilization of the morphology, with an almost complete suppression of coarsening during annealing. As a consequence, a substantial increase on the elongation at break without significant influence on ultimate tensile strength was achieved for compatibilized blends with different compositions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 14–22, 2006     

Morphology of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized by a methyl methacrylate/maleic anhydride copolymer

The morphologies of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized with a methyl methacrylate/maleic anhydride copolymer, with 3–20 wt % maleic anhydride, were examined by transmission electron microscopy. Some staining techniques were employed for identifying the various phases. The binary blends were immiscible and exhibited poor mechanical properties that stemmed from the unfavorable interactions among their molecular segments. This produced an unstable and coarse phase morphology and weak interfaces among the phases in the solid state. The presence of the copolymer in the blends clearly led to a more efficient dispersion of the acrylonitrile–butadiene–styrene phase and consequently optimized Izod impact properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3512–3518, 2003     

Relationship between branch length and the compatibilizing effect of polypropylene‐g‐polystyrene graft copolymer on polypropylene/polystyrene blends

Three polypropylene‐g‐polystyrene (PP‐g‐PS) graft copolymers with the same branch density but different branch lengths were evaluated as compatibilizing agents for PP/PS blends. The morphological and rheological results revealed that the addition of PP‐g‐PS graft copolymers significantly reduced the PS particle size and enhanced the interfacial adhesion between PP and PS phases. Furthermore, it is verified that the branch length of PP‐g‐PS graft copolymer had opposite effects on its compatibilizing effect: on one hand, increasing the branch length could improve the compatibilizing effect of graft copolymer on PP/PS blends, demonstrated by the reduction of PS particle size and the enhancement of interfacial adhesion; on the other hand, increasing the branch length would increase the melt viscosity of PP‐g‐PS graft copolymer, which prevented it from migrating effectively to the interface of blend components. Additionally, the crystallization and melting behaviors of PP and PP/PS blends were compared. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40126.     

pH‐ and temperature‐sensitive microfiltration membranes from blends of poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) and poly(N‐isopropylacrylamide)

The copolymer poly(vinylidene fluoride)‐graft‐poly(4‐vinylpyridine) (PVDF‐g‐P4VP) was prepared through the graft copolymerization of poly(vinylidene fluoride) with 4‐vinylpyridine. Through the blending of the PVDF‐g‐P4VP copolymer with poly(N‐isopropylacrylamide) (PNIPAm) in an N‐methyl‐2‐pyrrolidone solution, PVDF‐g‐P4VP/PNIPAm membranes were fabricated by phase inversion in aqueous media. Elemental analyses indicated that the blend concentration of PNIPAm in the blend membranes increased with an increase in the blend ratio used in the casting solution. Scanning electron microscopy revealed that the membrane surface tended to corrugate at a low PNIPAm concentration and transformed into a smooth morphology at a high PNIPAm concentration. The surface morphology and pore size distribution of the microfiltration membranes could be regulated by the blend concentration of the casting solution, temperature, pH, and ionic strength of the coagulation bath. X‐ray photoelectron spectroscopy revealed a significant enrichment of PNIPAm on the membrane surface. The flux of aqueous solutions through the blend membranes exhibited a pH‐ and temperature‐dependent behavior. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4089–4097, 2006     

Highly methanol resistant and selective ternary blend membrane composed of sulfonated PVdF‐co‐HFP,sulfonated polyaniline and nafion

Partially sulfonated poly(vinylidene fluoride‐co‐hexafluoro propylene)/partially sulfonated polyaniline (SPVdF‐co‐HFP/SPAni) binary blend membranes have shown promising results in terms of low methanol permeability and high membrane selectivity compared to Nafion‐117 membrane. However, the proton conductivity and IEC of this binary blend membrane was much lower than Nafion‐117. It was found that incorporation of minimal quantity of Nafion within SPVdF‐co‐HFP/SPAni blend membrane at a constituent weight % ratio of SPVdF‐co‐HFP:SPAni:Nafion = 50:40:10 induced significant improvements in ion‐exchange capacity (IEC), proton conductivity and tensile strength over that of the binary blend membrane. In addition, the SPVdF‐co‐HFP/SPAni/Nafion ternary blend membrane exhibited much lower methanol permeability, higher membrane and relative selectivities and comparable IEC to Nafion‐117. In effect, presence of minimal quantity of Nafion induced significant positive attributes to the ternary blend membrane; and assisted in reaching a balance between material cost and properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43294.     

Quaternized poly(phenylene oxide) anion exchange membrane for alkaline direct methanol fuel cells in KOH‐free media

A series of anion exchange membrane (AEM) electrolytes with quaternary ammonium moiety are fabricated from poly (phenylene oxide) for its application in alkaline direct methanol fuel cells (ADMFCs). In the first step, poly(phenylene oxide) (PPO) is successfully chloromethylated by substituting chloromethyl groups in the aryl position of polymer. In the second step, the chloromethylated PPO (CPPO) is further homogeneously quaternized and ion‐exchanged to form an AEM. From the second step, series of AEMs are prepared by changing the mole ratio of amine in relation to CPPO. The presence of quaternary ammonium group in the membrane was confirmed by elemental analysis. The fabricated membranes are subjected to cell polarization studies in ADMFCs, wherein quaternized poly(2,6‐dimethyl‐1,4‐phenylene oxide) (CPPO:amine of 1:8) membrane exhibits higher peak power density of 3.5 mW cm^?2 when compared with the other ratios of CPPO:amine in the absence of KOH solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43693.     

Influences of dicumyl peroxide on morphology and mechanical properties of polypropylene/poly(styrene‐b‐butadiene‐b‐styrene) blends via vane‐extruder

Polypropylene (PP) and poly(styrene‐b‐butadiene‐b‐styrene) block copolymer (SBS) were melt‐blended in the presence of initiator system. Dicumyl peroxide (DCP)/Triallyl isocyanurate (TAIC) via self‐deigned VE, aiming at in situ reactive compatibilization of toughed PP/SBS blend. The reactivity, morphology and mechanical properties of PP/SBS/DCP/TAIC blends were studied. Online torque detection was conducted to monitor changes in viscosities of reactive compatibilized blends, which could give proof of the interfacial grafted reaction induced by DCP/TAIC system. The effect of reactive compatibilization on the dispersed particles sizes and interfacial adhesion was studied by scanning electron microscopy. Analysis on mechanical performance revealed the impact strength improved after treated by initiator system, moreover, the impact‐fractured surface observation showed, the failure mode changed from debonding mechanism of neat 50PP/50SBS blend to plastic deformation mechanism of blend containing 3.0 phr initiator system. With improved interfacial adhesion, compatibilized blends not only were toughened but also exhibited enhanced tensile strength and thermal stability. Dynamic mechanical analysis showed a reduction of between PP phase and the PB segments in SBS phase, indicating reactive compatibilization of the blend was achieved. In the final part, a brief discussion was given about the dominant effects from chain scission of PP matrix to intergrafting reactions of PP and SBS, under different content of DCP/TAIC initiator system. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41543.     

Nanophase morphology and crystallization in poly(vinylidene fluoride)/polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene blends

An approach to achieve confined crystallization of ferroelectric semicrystalline poly(vinylidene fluoride) (PVDF) was investigated. A novel polydimethylsiloxane‐block‐poly(methyl methacrylate)‐block‐polystyrene (PDMS‐b‐PMMA‐b‐PS) triblock copolymer was synthesized by the atom‐transfer radical polymerization method and blended with PVDF. Miscibility, crystallization and morphology of the PVDF/PDMS‐b‐PMMA‐b‐PS blends were studied within the whole range of concentration. In this A‐b‐B‐b‐C/D type of triblock copolymer/homopolymer system, crystallizable PVDF (D) and PMMA (B) middle block are miscible because of specific intermolecular interactions while A block (PDMS) and C block (PS) are immiscible with PVDF. Nanostructured morphology is formed via self‐assembly, displaying a variety of phase structures and semicrystalline morphologies. Crystallization at 145 °C reveals that both α and β crystalline phases of PVDF are present in PVDF/PDMS‐b‐PMMA‐b‐PS blends. Incorporation of the triblock copolymer decreases the degree of crystallization and enhances the proportion of β to α phase of semicrystalline PVDF. Introduction of PDMS‐b‐PMMA‐b‐PS triblock copolymer to PVDF makes the crystalline structures compact and confines the crystal size. Moreover, small‐angle X‐ray scattering results indicate that the immiscible PDMS as a soft block and PS as a hard block are localized in PVDF crystalline structures. © 2019 Society of Chemical Industry     

Imidazole/(HPO3)3‐doped sulfonated poly (ether ether ketone) composite membrane for fuel cells

A novel gel of imidazole/(HPO₃)₃ was synthesized and incorporated into sulfonated poly (ether ether ketone) (SPEEK) to fabricate composite proton exchange membranes. The composite membranes were characterized by alternating current impedance (AC), thermogravimetry (TG), differential scanning calorimetry (DSC), X‐ray diffraction (XRD), scanning electron microscope (SEM) and mechanical property test. Based on the electrochemical performance investigation, the proton conductivity of the membrane is intimately correlated with the temperature and the mass ratio of imidazole/(HPO₃)₃ in the composite. The SPEEK/imidazole/(HPO₃)₃?4 composite membrane (with 44.4 wt % of imidazole/(HPO₃)₃) has the optimized performance at 135°C. Mover, the strength of the composite membranes is almost comparable to that of Nafion membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41946.     

Preparation of poly(vinylidene fluoride)/poly(methyl methacrylate) membranes by novel electrospinning system for lithium ion batteries

Fibrous membranes of poly(vinylidene fluoride)/poly(methyl methacrylate) (PVdF/PMMA) were fabricated by electrospinning method with different concentrations of polymer solution: 14, 16, and 18 wt %. The morphology of the electrospun membranes was observed by scanning electron microscopy. The images revealed that the nanofibers showed uniform diameter and no bead formation was observed with the concentration of 16 wt %. Also, the structure, crystallinity, ionic conduction, and electrochemical stability of the electrospun membranes were characterized. The results suggested that electrolyte uptake, ionic conduction, and electrochemical stability were improved by the addition of PMMA. Furthermore, with the 16 wt % concentration of the polymer solution, the membrane showed a high ionic conductivity of 3.5 mS cm^?1 at room temperature and electrochemical stability of up to 5.1 V. We predicted that this new method may be very promising for preparing microporous PVdF/PMMA polymer electrolytes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.