聚碳酸酯对聚偏氟乙烯结构和结晶行为的影响

通过熔融共混法制备聚偏氟乙烯/聚碳酸酯（PVDF/PC）共混物,采用X线衍射仪（XRD）和差示扫描量热仪（DSC）表征共混物的结构、熔融和结晶行为.考察不同聚碳酸酯含量对聚偏氟乙烯晶体结构、熔点以及晶体完善程度等的影响.同时通过Avram i方程和结晶速率系数的研究,探讨PC对PVDF非等温结晶动力学的影响.研究结果表明：PC的掺杂没有改变PVDF的晶体结构,但是高PC质量分数（70%以上）却不利于PVDF晶体的生成;随着PC质量分数的增加,生成的PVDF晶体完善程度逐渐降低;当PC质量分数在70%以下时,PC起到类似成核剂作用,提高PVDF结晶速率.     

Phase behavior of poly(ε-caprolactone)/ poly (vinylidene fluoride) blends

The miscibility of blends of poly (ε-caprolactone) (PCL)/poly(vinylidene fluoride) (PVDF) was studied by measuring the cloud point, melting point depression and crystallization kinetics. Lower critical solution temperature (LCST) behavior was observed at PCL-rich compositions, whilst it was not observed at high compositions of PVDF. However it is possible that an LCST could exist below the melting point of PVDF. From analysis of the melting point depression, the Flory interaction parameter x₁₂, was calculated from the Nishi-Wang equation and the value was found to be-1.5. The crystallization rate of PCL increased with increasing amount of PVDF in the blend. The spinodal curve for PCL/PVDF blends was simulated by using the lattice-fluid theory.     

Membrane formation of poly(vinylidene fluoride)/poly(methyl methacrylate)/diluents via thermally induced phase separation

The role of the single diluents and mixed diluents on the poly (vinylidene fluoride) (PVDF)/poly(methyl methacrylate) (PMMA) blend membranes via thermally induced phase separation (TIPS) process was investigated. The crystallization behaviors of PVDF in the diluted samples were examined by differential scanning calorimetry. The melting and crystallization temperatures of those diluted PVDF blend were decreased with the enhanced interactions between polymer chains and diluent molecules. The crystallinity of PVDF in the diluent was always higher than that obtained in PVDF blend sample. This can be explained by the dilution effects, which increased the average spatial separation distances between crystallizable chains. Thus, the PVDF crystallization was favored. Additionally, solid‐liquid (S‐L) phase separation occurred in the quenched samples. Illustrated by scanning electron microscopy, inter‐ and intraspherulitic voids were formed in the ultimate membranes, which related to the polymer/diluent interactions, the kinetics of crystallization and diluent rejection from the growing crystal. The porosity of the PVDF blend membranes obtained from the mixed diluents was higher than those obtained from the single diluent samples. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of poly(vinylidene fluoride) polymorphic structures on the crystallization behavior of poly(butylene succinate)

The detail information of both α and β form poly(vinylidene fluoride) (PVDF) crystal effect on the crystallization behavior of poly(butylene succinate) (PBS) were systematically studied. The results show that β form PVDF can obviously improve the melt‐crystallization temperature of PBS during the nonisothermal crystallization process. Both crystallization time span and spherulitic size of PBS decrease with the increasing amount of β form PVDF, which enhances the primary nucleation of PBS. But α form PVDF shows no nucleating effect on PBS crystallization, exhibiting as almost unchanged T_c values for α form PVDF‐blended PBS samples. The intrinsic mechanism for the nucleating effect of β form PVDF on PBS was proposed to be the epitaxial crystallization. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40991.     

PVDF porous matrix with controlled microstructure prepared by TIPS process as polymer electrolyte for lithium ion battery

Poly(vinylidene fluoride) (PVDF) microporous matrix of polymer electrolyte for lithium ion battery was prepared via the thermally induced phase separation (TIPS) process using diluent mixture of dibutyl phthalate (DBP) and di(2-ethylhexyl) phthalate (DEHP). Since this method has only one parameter, namely the DBP/DEHP ratio in diluent mixture, the membrane microstructure is easily and conveniently controlled. With the assistance of a pseudo-binary temperature-DBP ratio phase diagram of the PVDF-diluent mixture system, the membrane formation mechanism for different microstructures of membranes was proposed. In addition to studying the different microstructures available in TIPS process, the relationship between performance of membrane, electrochemical property of polymer electrolyte and final microstructure has been investigated in this paper.     

Crystallization behavior of poly(vinylidene fluoride)/montmorillonite nanocomposite

The crystallization behavior of poly(vinylidene fluoride)/montmorillonite (PVDF/MMT) nanocomposite was investigated by using differential scanning calorimeter (DSC), polarizing optical microscope (POM), and X‐ray diffraction. The results showed that the crystallization behavior of PVDF was changed by adding MMT in PVDF matrix. The MMT layers in PVDF acted as effective nucleation agents. It is observed that the crystallization temperature of PVDF/MMT nanocomposite was higher than that of PVDF at various cooling rates. The value of half‐time of crystallization showed that the crystallization rate of PVDF/MMT nanocomposite was faster than that of PVDF at a given cooling rate. The addition of MMT hindered the growth of spherulite. Nonisothermal crystallization data was analyzed using Avrami, Ozawa, and Jeziorny method. The Jeziorny method successfully described the nonisothermal crystallization behaviors of PVDF/MMT nanocomposite. The MMT loading was favorable to produce the piezoelectric β phase in the PVDF matrix. The α phase coexisted with the β phase in the PVDF/MMT nanocomposite. For this polymorphic structure, a possible explanation was proposed based on the variable temperature X‐ray diffraction, DSC, and POM experiments. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

The crystallization and transition behavior of poly(vinylidene fluoride)/copoly(chlorotriofluorethylene-vinylidene fluoride) blends

Thermal analysis of solution precipitated blends of two crystallizable polymers, poly(vinylidene fluoride) (PVDF) and copoly(chlorotrifluorethylene-vinylidene fluoride) (copoly(CTFE-VDF)), has been carried out to study the transition temperatures, crystallinity, and crystallization rates. PVDF crystallizes over the whole blend composition either during precipitation from solution or upon cooling from the melt. The high degree of crystallinity attained, higher than in PVDF by itself, suggests the occurrence of partial PVDF-copolymer cocrystallization. The melt crystallization temperature, decreasing with cooling rate, is lower in PVDF-rich blends than for lean blends. However, the heat of crystallization increases with cooling rate, suggesting that the crystal composition depends on crystallization rate. No significant melting temperature depression due to blending was observed. However, the blends glass transition (T_g) changes linearly with composition, but less than expected by any mixing rule applicable to compatible systems. Annealing of the blends above T_g results in an additional crystalline phase consisting mainly of the copolymer. The amount of these crystals increases with PVDF content, due to partial cocrystallization and kinetic effects. The addition of the copolymer to PVDF results in a volume-filling spherulitic structure consisting of spherulites which decrease in size with increasing copolymer content.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Plasticizer effect of dibutyl phthalate on the morphology and mechanical properties of hard elastic poly(vinylidene fluoride) fibers

To improve the structure and hard elasticity of poly(vinylidene fluoride) (PVDF) fibers, a small amount of the plasticizer dibutyl phthalate (DBP) was added to PVDF. The PVDF/DBP blend fibers were prepared by melt spinning and subsequent annealing. The crystalline structure and thermal properties of the blend fibers were analyzed in terms of the long‐period lamellar spacing, crystal structure, and degree of crystallinity with X‐ray diffraction, differential scanning calorimetry, and small‐angle X‐ray scattering. The results indicated that stacked crystalline lamellae, which were aligned normal to the fiber axis, existed in the blend fibers, and they were in the form of an α‐crystal phase. The total crystallinity of the blend fibers was higher than that of the pure PVDF fibers, and it reached its highest value when the DBP concentration was 2 wt %; then, it decreased with an increase in the DBP content. The morphology and mechanical properties of the fibers were also investigated with scanning electron microscopy and electronic tensile experimentation. The results of scanning electron microscopy apparently exhibited a small porous structure on the surface of the blend fibers, and the more DBP there was in the PVDF fibers, the more porous structure was obtained. Mechanical experiments indicated that the fibers with a 5 wt % concentration of DBP had better elastic recovery and breaking strain than the pure PVDF fibers. These results all indicated that DBP‐modified PVDF fibers have potential applications in preparing microporous membranes by a melt spinning and stretching process. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Counterion dependent crystallization kinetics in blends of a perfluorosulfonate ionomer with poly(vinylidene fluoride)

Blends of poly(vinylidene fluoride) (PVDF) with a perfluorosulfonate ionomer, Nafion^®, have been prepared and examined in terms of the crystallization kinetics of the PVDF component. In blends of PVDF with Na⁺-form Nafion^®, the rates of bulk crystallization, as observed by DSC, and the spherulitic growth rates of the PVDF component, as observed using optical microscopy, were found to be very similar to that of pure PVDF. This behavior was attributed to the course phase separation of Na⁺-form Nafion^® from PVDF and melt incompatibility of the physically cross-linked ionomer with the crystallizable component. In this segregated state, the PVDF component of the blend is allowed to crystallize in pure phases that are isolated under the influence of Nafion^®. In contrast, when the ionomer was exchanged with more weakly interacting quaternary alkylammonium counterions, a decrease in both the rate of bulk crystallization and spherulitic growth was observed. Furthermore, the crystallization kinetics of PVDF in these blends was found to be dependent on the counterion size; as the size of counterions associated with the Nafion^® component increased, the rate of crystallization decreased. This behavior was attributed to a weakening of the electrostatic interactions in the ionomer phase and thus an increase in the extent of phase mixing with the larger ions.     

Investigation of the structural,thermal, mechanical,and optical properties of poly(methyl methacrylate) and poly(vinylidene fluoride) blends

In this investigation, poly(methyl methacrylate) (PMMA) and poly(vinylidene fluoride) (PVDF) blends (w/w) were prepared in a Brabender (South Hackensack, NJ) plasticorder with a thermoplastic mixing chamber (type W60) preheated at 180°C. These blends were further converted into films by a conventional solution casting method and characterized with Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction, mechanical property measurements, impact strength testing, ultraviolet–visible spectroscopy, refractive‐index measurements, and contact‐angle study. The Fourier transform infrared results indicated that the compatibility between these two systems resulted from hydrogen bonding between the carbonyl group of PMMA and the CH₂ group of PVDF. The thermal analysis showed depressions in the glass‐transition temperature, melting temperature, and crystallization temperature. The heat of crystallization increased with an increase in the PVDF content in the blend. An increase in the heat of crystallization meant an increase in the crystallinity. An increase in the cooling rate increased the crystallization rate. The improvement in the mechanical properties of the blend films indicated that the observed behavior was ascribable to a more coherent structure of the blends due to strong specific interactions between PMMA and PVDF chains. The impact strength analysis revealed a substantial increase in the impact strength from 21.64 to 38.52 J/m. Optical absorption spectra suggested the presence of an optical band gap energy that increased with an increase in the PVDF content in the blend. The contact angle against water increased with the PVDF content in the blend film, and this was caused by the hydrophobicity of PVDF due to the CF₂ group of PVDF. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization behavior of nano-composite based on poly(vinylidene fluoride) and organically modified layered titanate

To understand the effect of the nano-filler particles on the crystallization kinetics and crystalline structure of poly(vinylidene fluoride) (PVDF) upon nano-composite formation, we have prepared PVDF/organically modified layered titanate nano-composite via melt intercalation technique. The layer titanate (HTO) is a new nano-filler having highly surface charge density compared with conventional layered silicates. The detailed crystallization behavior and its kinetics including the conformational changes of the PVDF chain segment during crystallization of neat PVDF and HTO-based nano-composite (PVDF/HTO) have been investigated by using differential scanning calorimetric, wide-angle X-ray diffraction, light scattering, and infrared spectroscopic analyses. The neat PVDF predominantly formed α-phase in the crystallization temperature range of 110-150 °C. On the other hand, PVDF/HTO exhibited mainly α-phase crystal coexisting with γ- and β-phases at low T_c range (110-135 °C). A major γ-phase crystal coexists with β- and α-phases appeared at high T_c (=140-150 °C), owing to the dispersed layer titanate particles as a nucleating agent. The overall crystallization rate and crystalline structure of pure PVDF were strongly influenced in the presence of layered titanate particles.     

Spherulitic morphology and growth of poly(vinylidene fluoride)/poly(3-hydroxybutyrate-co-hydroxyvalerate) blends by optical microscopy

Poly(vinylidene fluoride) (PVDF) and poly(3-hydroxybutyrate-co-hydroxyvalerate) (PHBV), both semicrystalline polymers, are miscible as shown by the single glass transition temperature over the entire composition range. Morphology of PVDF/PHBV blends was investigated by optical microscopy under two different crystallization conditions. PVDF showed the spherulitic morphology at 150 °C in the PVDF/PHBV blends, where PHBV acted as the noncrystallizing component. PHBV also showed the spherulitic morphology within the matrix of the pre-existing PVDF crystals when PVDF/PHBV blends were quenched from the melt to the crystallization temperature below the melting point of PHBV. The spherulitic growth of PHBV was investigated as the function of both blend composition and crystallization temperature.     

Morphology and properties of poly(vinylidene fluoride)/silicone rubber blends

Blends of poly(vinylidene fluoride) (PVDF) and silicone rubber (SR) were prepared through melt mixing. The morphology, rheology, crystallization behavior, mechanical properties, dynamic mechanical properties and thermal properties of the PVDF/SR blends were investigated. The blend with 9 wt % of SR showed spherical shape of disperse phase whereas the blend with 27 wt % of SR resulted in irregular shape of rubber phase. The rheology showed that the complex viscosity and storage modulus of the blends decreased with increasing the SR content. The mechanical properties of the blends were decreased with increasing the SR content but that were significantly improved after dynamical vulcanization. The crystallization temperature of PVDF phase in PVDF/SR blends was increased. The incorporation of SR improved the thermal stability of PVDF/SR blends, and the temperature at 10% mass loss of the blends increased to about 489°C compared with 478°C of the pure PVDF. The mass of residual char in experiment of the blends was lower than that obtained in theory. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39945.     

Morphology of polyvinylidene fluoride and its blend in thermally induced phase separation process

Polyvinylidene fluoride (PVDF) and its blend films were prepared by melt‐blending the binary mixture of PVDF/dibutyl phthalate (DBP) and the ternary mixture of PVDF/CaCO₃/DBP in combination of TIPS. Their morphologies were characterized by scanning electron microscope depended on preparation condition, such as the diluent and CaCO₃ weight fraction, and the cooling rate, and the crystallization information was also investigated by DSC. The results showed that CaCO₃ influenced the morphology of PVDF in the TIPS process regardless of the cooling conditions, and the formation of the spherulitic morphology can be disturbed by CaCO₃ at the quenching condition. The effect of CaCO₃ weight fraction on the tensile strength of PVDF was measured, which indicated CaCO₃ had a negative effect on PVDF tensile strength. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2944–2952, 2006     

Preparation,crystallization behavior,and dynamic mechanical property of nanocomposites based on poly(vinylidene fluoride) and exfoliated graphite nanoplate

Nanocomposites based on poly(vinylidene fluoride) (PVDF) and exfoliated graphite nanoplate (xGnP) were prepared by solution precipitation method. The resulting nanocomposites were investigated with respect to their structure and properties by scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and dynamic mechanical analysis. Both SEM and TEM examinations confirmed the good dispersion of xGnP in the PVDF matrix. The nonisothermal crystallization behavior of the PVDF/xGnP nanocomposites was studied using DSC technique at various cooling rates. The results indicated that the xGnPs in nanometer size might act as nucleating agents and accelerated the overall nonisothermal crystallization process. Meanwhile, the incorporation of xGnP significantly improved the storage modulus of the PVDF/xGnP nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The crystalline phase transformation of poly(vinylidene fluoride)/poly(vinyl fluoride) blend films

Poly(vinylidene fluoride) (PVDF), poly(vinyl fluoride) (PVF), and their blends were prepared by solution casting, followed by quenching in ice water after melting to obtain an α-crystalline phase. The films were drawn by solid state extrusion at two different drawing temperatures, 50°C and 110°C. The crystalline phases were analyzed by DSC and FTIR. In the undrawn films, the content of β-crystalline phase in the blend of PVDF/PVF 88.5/11.5 was higher than in the PVDF homopolymer, but it was lower than in the PVDF film with a draw ratio higher than 4. The α-crystalline phase in PVDF/PVF blends was mostly transformed into the β-crystalline phase beyond a draw ratio of 4, regardless of the draw temperature and PVF content. The α-crystalline phase of PVDF systematically transformed into the β-crystalline phase with increasing draw ratio. The crystallinity of PVDF/PVF blend films drawn at 110°C was higher than those drawn at 50°C. In the drawn blend films, characteristic IR bands of the α form were shifted to those of the β form and completely changed into those of β form at draw ratio of 4, regardless of the draw temperature and PVF content.     

Spherulitic Morphology and Crystallization Kinetics of Poly(vinylidene fluoride)/Poly(vinyl acetate) Blends

Spherulitic morphology and crystallization kinetics of the blends of poly(vinylidene fluoride) (PVDF) and poly(vinyl acetate) (PVAc) prepared by solution casting films have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The results suggested that PVAc was mainly segregated into the interlamellar and/or interfibrillar regions due to the volume-filling spherulitic morphology observed. As for the results of crystallization kinetics, it was found that both the PVDF spherulitic growth rate (G ^PVDF) and the overall crystallization rate constant (k _n ) were depressed with either the addition of PVAc component or the increase of crystallization temperature (T _c). The kinetics retardation was attributed to the decrease in PVDF molecular mobility and dilution of PVDF concentration due to the addition of PVAc, which has a higher glass transition temperature (T _g).     

Crystallization and orientation behaviors of poly(vinylidene fluoride) in the oriented blend with nylon 11

Oriented films of nylon 11/poly(vinylidene fluoride) (PVDF) blend were prepared by uniaxially stretching the melt-mixed blends. The drawn films of fixed length were heat-treated at 170 °C for 5 min to melt the PVDF component, followed by quenching in ice water or isothermal crystallization at various temperatures. The crystal forms and orientation textures of the obtained samples were studied using wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS). It was found that PVDF can crystallize into both and β forms in the nylon 11/PVDF blends, and that the content of the β form increases with increasing crystallization temperature above 120 °C. The orientation behavior of the -form PVDF was observed to be dependent on the crystallization conditions: c-axis orientation to the stretching direction was produced for the sample crystallized below 50 °C; the a-axis of crystals was tilted from the stretching direction when PVDF was crystallized at about 75 °C; the parallel orientation of the a-axis to the stretching direction becomes dominant at higher crystallization temperatures (above 100 °C). In contrast, the β crystalline form maintains the c-axis orientation irrespective of crystallization temperature. It was shown by the confocal laser scanning microscopy that cylindrical domains of PVDF were dispersed in the oriented matrix of nylon 11. The mechanism for the formation of the unique orientation textures is discussed in detail. It was proposed that the a-axis orientation is a result of the trans-crystallization of PVDF in the cylindrical domains confined by the oriented matrix of nylon 11. The crystallization kinetics, WAXD analysis, and morphology studies preferred the trans-crystallization mechanism. The mechanical properties of the as-drawn and heat-treated samples were measured not only in the stretching direction but also in the direction perpendicular to it. It was found that the heat-treated samples show slightly lower tensile strength, but more elongation at the break in the two directions than the as-drawn samples.     

Influence of fluorine interface to the crystallization of poly (vinylidene fluoride)/silicone rubber/fluororubber elastomeric tertiary blends via dynamical curing

ABSTRACT

We demonstrate the influence of fluorine interface to the crystallization of poly(vinylidene fluoride) (PVDF)/silicone rubber (SR)/fluororubber (FKM) tertiary dynamic curing blends. In contrast to PVDF/SR binary blend, the average size of PVDF spherulites turns smaller and the crystallization rate is lower in PVDF/SR/FKM tertiary blend when more fluororubber component was added into the blends at the same crystallization temperature. Incorporation of FKM does not change the crystalline form of PVDF in the blends. The resulting mechanical properties of tensile strength, flexural strength, Izod impact strength and elongation at break for PVDF/SR/FKM tertiary blends are enhanced compared with PVDF/SR binary blend.