Luminescent properties of Sr2P2O7:Eu,Mn phosphor under near UV excitation

The phosphors in the system Sr_2−x−yP₂O₇:xEu²⁺,yMn²⁺ were synthesized by solid-state reactions and their photoluminescence properties were investigated. These phosphors have strong absorption in the near UV region, which is suitable for excitation of ultraviolet light emitting diodes (UVLEDs). The orange-reddish emission of Mn²⁺ in these phosphors can be used as a red component in the tri-color system and may be enhanced by adjusting the Mn²⁺/Eu²⁺ ratio. The energy transfer from Eu²⁺ to Mn²⁺ is observed with a transfer efficiency of ∼0.45 and a critical distance of ∼10 Å. The results reveal that Sr_2−x−yP₂O₇:xEu²⁺,yMn²⁺ phosphors could be used in white light UVLEDs.     

Investigation of Na3GdP2O8:Tb as a potential green-emitting phosphor for plasma display panels

The photoluminescent properties of a series of Tb³⁺-doped Na₃GdP₂O₈ phosphors excitable by vacuum ultraviolet and ultraviolet light are reported. The host related absorption, f-f and f-d transitions of Gd³⁺ and Tb³⁺, and charge transfer of O²⁻ → Gd³⁺ and O²⁻ → Tb³⁺ are assigned. Under 147 nm light excitation, Na₃GdP₂O₈:Tb³⁺ phosphors show efficient green emissions with a dominant peak at 545 nm. The optimal sample Na₃Gd_0.4Tb_0.6P₂O₈ shows a shorter decay time and a comparable brightness when compared with the commercial Zn₂SiO₄:Mn²⁺ green phosphor. These results demonstrate that it is a potential candidate for plasma display panels application.     

Porous MAl2O4:Eu (Eu), Dy (M = Sr, Ca, Ba) phosphors prepared by Pechini-type sol-gel method: The effect of solvents

In this work, a series of porous Eu²⁺-doped alkaline earth aluminates phosphors including MAl₂O₄:Eu²⁺ (Eu³⁺), Dy³⁺ (M = Sr, Ca, Ba) have been prepared by Pechini-type sol-gel approach, using citric acid as chelating ligand and ethylene glycol (or H₂O) as solvent. The as-obtained samples were characterized by means of XRPD, FESEM and PL techniques. MAl₂O₄:Eu²⁺, Dy³⁺ (M = Sr, Ca, Ba) phosphors were prepared in a reducing atmosphere (H₂/Ar, 20 + 80%) while MAl₂O₄:Eu³⁺, Dy³⁺ (M = Sr, Ca, Ba) phosphors were obtained in air. Upon changing the molar ratio of citric acid to total metal cations concentration in ethylene glycol can produce spherical phosphors and the higher molar ratio favors the formation of spherical ones. Otherwise, irregular shaped phosphors occur when conducting the reaction in pure H₂O. The irregular shaped phosphors have higher emission intensity than those spherical ones observed with the help of excitation spectra, emission spectra and decay curves.     

Influence of excitation wavelengths on luminescent properties of Sr3Al2O6:Eu, Dy phosphors prepared by sol-gel-combustion processing

Eu²⁺ and Dy³⁺ ion co-doped Sr₃Al₂O₆ red-emitting long afterglow phosphor was synthesized by sol-gel-combustion methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu₂O₃, Dy₂O₃, H₃BO₃ and C₆H₈O₇·H₂O as raw materials. The crystalline structure of the phosphors were characterized by X-ray diffraction, luminescent properties of phosphors were analyzed by fluorescence spectrophotometer. The effect of excitation wavelengths on the luminescent properties of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphors was discussed. The emission peak of Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor lays at 516 nm under the excitation of 360 nm, and at 612 nm under the excitation of 468 nm. The results reveal that the Sr₃Al₂O₆:Eu²⁺, Dy³⁺ phosphor will emit a yellow-green light upon UV illumination, and a bright red light upon visible light illumination. The emission mechanism was discussed according to the effect of nephelauxetic and crystal field on the 4f⁶5d¹ → 4f⁷ transition of the Eu²⁺ ions in Sr₃Al₂O₆. The afterglow time of (Sr_0.94Eu_0.03Dy_0.03)₃ Al₂O₆ phosphors lasts for over 600s after the excited source was cut off.     

Photoluminescence of Tb and Mn activated Ca8MgGd(PO4)7 under vacuum ultraviolet excitation

Novel Tb³⁺ and Mn²⁺ activated Ca₈MgGd(PO₄)₇ phosphors were synthesized by solid-state reaction and their photoluminescence properties in vacuum ultraviolet region were investigated for the first time. It can be observed from the excitation spectra that the host-related absorption band is located around 170 nm, and it overlaps the O²⁻ → Tb³⁺ charge transfer band of Ca₈MgGd(PO₄)₇:Tb³⁺ around 161 nm and the 3d⁵ → 3d⁴4s transition band of Ca₈MgGd(PO₄)₇:Mn²⁺ near 200 nm. The 4f-4f 5d spin-allowed and spin-forbidden transitions of Tb³⁺ are verified to be located at 170-250 and 257-271 nm, respectively. Upon 147 nm excitation, the dominant emission peak intensity of the Ca₈MgGd_0.1(PO₄)₇:0.9Tb³⁺ phosphor is about 2.7 times stronger than that of the commercial Zn₂SiO₄:Mn²⁺ green phosphor, and the brightness of the former with a short decay time of 2.5 ms is about 98% of the latter’s. The Ca₈MgGd(PO₄):Mn²⁺ phosphor excited at 147 nm exhibits a deep red emission around 650 nm, which could be attributed to the ⁴T₁ → ⁶A₁ transition of Mn²⁺, with the CIE index (0.679, 0.321). In a word, the results above indicate that both Tb³⁺ and Mn²⁺ activated Ca₈MgGd(PO₄)₇ phosphors could be promising for PDP or Hg-free lamp applications.     

Luminescence of SrGdGa3O7:RE(RE = Eu, Tb) phosphors and energy transfer from Gd to RE

Eu³⁺- and Tb³⁺-activated SrGdGa₃O₇ phosphors were synthesized by the solid-state reaction and their luminescence properties were investigated. Sr(Gd_1 − xEu_x)Ga₃O₇ and Sr(Gd_1 − xTb_x)Ga₃O₇ formed continuous solid solution in the range of x = 0-1.0. Unactivated SrGdGa₃O₇ exhibited a typical characteristic excitation and emission of Gd ion. The SrGdGa₃O₇:xEu³⁺ and SrGdGa₃O₇:xTb³⁺ phosphors also showed the well-known Eu³⁺ and Tb³⁺ excitation and emission. The energy transfer from Gd³⁺ to Eu³⁺ and Tb³⁺ were verified by photoluminescence spectra. The dependence of photoluminescence intensity on Eu³⁺ and Tb³⁺ concentration were also studied in detail and the photoluminescence (PL) intensity of SrGdGa₃O₇:Eu and SrGdGa₃O₇:Tb were compared with commercial phosphors, Y₂O₃:Eu and LaPO₄:Ce,Tb. The luminescence decay measurements showed that the lifetimes of Eu³⁺ and Tb³⁺ were in the range of microsecond. The energy transfer from Gd³⁺ to Tb³⁺ was also observed in decay curve.     

M2Si5N8:Eu-based (M = Ca, Sr) red-emitting phosphors fabricated by nitrate reduction process

M₂Si₅N₈:Eu²⁺-based (M = Ca, Sr) red-emitting phosphors were fabricated at relatively low temperature (1200 °C) and atmospheric pressure using a simple solid-state reaction process. Several processing parameters were systematically investigated to optimize the phosphors structural characterization and photoluminescence performance, including the amount of europium and the properties of the precursor and activated materials. The as-prepared M₂Si₅N₈:Eu²⁺-based (M = Ca, Sr) phosphors were orange in color and emitted intensively in the red region of 580-670 nm under 465 nm excitation. This simple fabrication technique can be readily used for the optimization of phosphor microstructures and high-performance red-emitting phosphors since it eliminates many air-sensitive precursors.     

Sol-gel composition of multicomponent hybrid precursors to long afterglow of CaxSr1 − xAl2O4: Eu phosphors

Ca_xSr_1 − xAl₂O₄: Eu²⁺ photoluminescent materials with high brightness and long afterglow were in situ synthesized by hybrid precursor assembly sol-gel technology in a reductive atmosphere. The particle size of luminescent materials is in the range of 30-60 nm by the estimation of XRD. And SEM shows that there exists uniform morphology and microstructure owing to the hybrid precursors. The influence of co-doping Ca²⁺ and Sr²⁺ on the luminescence of the phosphor was studied. Their excitation and emission spectra were very similar to that of SrAl₂O₄: Eu²⁺ phosphors and all of them have long afterglow phenomenon. Changing the co-doping concentrations of Ca²⁺ and Sr²⁺ in Ca_xSr_1 − xAl₂O₄: Eu²⁺ phosphors, the luminescent intensities are different. When the proportion of Ca and Sr is 6 to 4, the phosphor reaches the strongest emitting intensity.     

Luminescent properties of Eu-activated (Sr1−z, Caz)(Al1−y, By)2O4 phosphors for UV LEDs

A series of (Sr_1−z, Ca_z)(Al_1−y, B_y)₂O₄:xEu²⁺ phosphors were synthesized by the sol–gel process and were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), and photoluminescence (PL) excitation and emission spectra. The experiment results revealed that the highest intensity of Sr(Al_1.98, B_0.02)O₄:Eu²⁺ phosphor with pure monoclinic SrAl₂O₄ was achieved by annealing at the temperature of 1200 °C and the Eu²⁺ content of 8 mol%. However, when the post-treatment temperature for Sr(Al_1.98, B_0.02)O₄: Eu²⁺ was over 1200 °C, the Sr₄Al₁₄O₂₅ phase appeared as a minor phase, inducing small blue-shift in the emission peak (520–509 nm). Doping higher content of B³⁺ (y = 0.02–0.40) into SrAl₂O₄:Eu²⁺ at 1200 °C resulted in the transformation of phase from SrAl₂O₄ to Sr₄Al₁₄O₂₅ as well as to SrB₂Al₂O₇, which made the emission intensity enhance and the emission shift to a much shorter wavelength region (λ_p = 467 nm). It was found that, instead of purely using Sr atoms, Ca atoms with content of 20–40% could induce the crystal structure of (Sr_1−z, Ca_z)(Al_1−y, B_y)₂O₄:xEu²⁺, which led to SrAl₂O₄ from monoclinic to hexagonal phase. As a result, SrAl₂O₄ solid solution was obtained and then SrAl₂O₄:Eu²⁺ to emit 518 nm green light. At higher Ca content (z > 40%), a new CaAl₂O₄ solid solution was formed and a blue emission of CaAl₂O₄:Eu²⁺ was obtained.     

Photoluminescence properties of NaGd(MoO4)2:Eu nanophosphors prepared by sol-gel method

NaGd(MoO₄)₂:Eu³⁺ (hereafter NGM:Eu) phosphors have been prepared by sol-gel method. The properties of the resulting phosphors are characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), photoluminescence (PL) spectra and decay curve. The excitation spectra of NGM:Eu phosphors are mainly attributed to O → Mo charge-transfer (CT) band at about 282 nm and some sharp lines of Eu³⁺ f-f transitions in near-UV and visible regions with two strong peaks at 395 and 465 nm, respectively. Under the 395 and 465 nm excitation, intense red emission peaked at 616 nm corresponding to ⁵D₀ → ⁷F₂ transition of Eu³⁺ are observed for 35 at.% NGM:Eu phosphors as the optimal doping concentration. The luminescence properties suggest that NGM:Eu phosphor may be regarded as a potential red phosphor candidate for near-UV and blue light-emitting diodes (LEDs).     

Luminescence properties of Ce and/or Mn activated Ca10K(PO4)7 under ultraviolet and vacuum ultraviolet excitation

New Ce³⁺ and/or Mn²⁺ activated Ca₁₀K(PO₄)₇ phosphors were prepared by solid-state reaction, and their photoluminescence properties upon ultraviolet and vacuum ultraviolet excitation were investigated. Under 254 nm excitation, a series of Ca₁₀K(PO₄)₇:xMn²⁺ samples exhibit two emission bands at 463 and 650 nm, which could be attributed to oxygen defects and ⁴T₁–⁶A₁ transition of Mn²⁺, respectively. And an energy transfer from defects to Mn²⁺ has been observed. With the Mn²⁺ content increased, the emitting hues of Ca₁₀K(PO₄)₇:Mn²⁺ can range from blue to red. By co-doping Ce³⁺ to Ca₁₀K(PO₄)₇:Mn²⁺, the emission intensity of Mn²⁺ is strongly enhanced due to an efficient energy transfer by [Ce³⁺ → Mn²⁺] and [defects → Ce³⁺ → Mn²⁺]. But under 147 nm excitation, the emission intensity of Mn²⁺ in Ca₁₀K(PO₄)₇:0.25Mn²⁺ decreases slightly compared with that in Ca₁₀K(PO₄)₇:025Mn²⁺, 0.1Ce³⁺, 0.1K⁺ due to the host sensitization competition between Ce³⁺ and Mn²⁺.     

M2Y8(SiO4)6O2: Tb (M = Ca, Sr) phosphors: Sol-gel synthesis from N-2-aminoethylic-3-aminopropyldiethoxysilane and different photoluminescence behavior

M₂Y₈(SiO₄)₆O₂: Tb³⁺ (M = Ca, Sr) phosphors have been synthesized with a new silicon source silane crosslinking reagent (N-2-aminoethylic-3-aminopropyldiethoxysilane [NH₂(CH₂)₂NH(CH₂)₃SiCH₃(OCH₃)₂], abbreviated as AEAPMMS) through the sol-gel process, both of which present the characteristic emission ⁵D₄ → ⁷F_J (J = 6, 5, 4, 3) of Tb³⁺ ions. It is interesting to be found that the high energy level blue emission (⁵D₃ → ⁷F_J (J = 6, 5, 4, 3) transition) still can be found in the emission spectrum of Ca₂Y₈(SiO₄)₆O₂: Tb³⁺ while it disappears in the emission spectrum of Sr₂Y₈(SiO₄)₆O₂: Tb³⁺ for the cross-relaxation-induced quenching.     

Sr3.5Mg0.5Si3O8Cl4: Eu bluish-green-emitting phosphor for NUV-based LED

Sr₄Si₃O₈Cl₄:Eu²⁺ and Sr_3.5Mg_0.5Si₃O₈Cl₄:Eu²⁺ phosphors were prepared by a conventional solid state reaction (SS). Excited by 370 nm near-ultraviolet light, the phosphors show an efficient bluish-green wide-band emission centering at 484 nm, which originates from the 4f5d¹ → 4f⁷ transition of Eu²⁺ ion. The excitation spectra of the phosphors are a broad band extending from 250 nm to 400 nm. Mg²⁺-codoping greatly enhances the bluish-green emission of the phosphors. An LED was fabricated by coating the Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ phosphor onto an ~ 370 nm-emitting InGaN chip. The LED exhibits bright bluish-green emission under a forward bias of 20 mA. The results indicate that Sr_3.5Mg_0.5Si₃O₈Cl₄:0.08Eu²⁺ is a candidate as a bluish-green component for fabrication of NUV-based white LEDs.     

Hydrothermal synthesis and photoluminescence of SrWO4:Tb novel green phosphor

Tb³⁺-doped SrWO₄ phosphors with a scheelite structure have been prepared by hydrothermal reaction. X-ray powder diffraction, field-emission scanning electron microscopy, photoluminescence excitation and emission spectra and decay curve were used to characterize the resulting samples. Scanning electron microscopy image showed that the obtained SrWO₄:Tb³⁺ phosphors appeared to be nearly spherical and their sizes ranged from 1 to 3 μm. Photoluminescence spectra indicated the phosphors emitted strong green light centered at 545 nm under ultraviolet light excitation. Because 12 at.% SWO₄:Tb³⁺ phosphor exhibits intensive green emission under 254 nm excitation in comparison with the commercial green fluorescent lamp phosphor (LaPO₄:Ce,Tb), the excellent luminescence properties make it a new promising green phosphor for fluorescent lamps application.     

Preparation and characterization of Sr-hardystonite (Sr2ZnSi2O7) for bone repair applications

In this work, the potential of Sr-hardystonite (Sr₂ZnSi₂O₇) ceramics for biomedical use was first detected. First, pure Sr₂ZnSi₂O₇ powders were successfully synthesized by sol-gel method, and then Sr₂ZnSi₂O₇ ceramics were prepared by sintering the powder compacts. The mechanical test showed that the bending strength and Young's modulus of Sr₂ZnSi₂O₇ ceramics could reach 82 MPa and 44 GPa, respectively, which were close to the values for human cortical bone. Degradation test in Tris-HCl buffer solution showed that Sr₂ZnSi₂O₇ ceramics had a low degradation rate with less than 3% weight loss after soaking for 28 days. Furthermore, the in vitro biocompatibility of the ceramics was evaluated by rabbit bone marrow stem cells (rBMSCs) adhesion and proliferation assay. The results showed that the ceramics supported the cells adhesion and proliferation. Taken together, Sr₂ZnSi₂O₇ might be a potential candidate for preparation of bone implants.     

GeO2 dopant induced enhancement of red emission in CaAl12O19:Mn phosphor

In order to search efficient red-emitting phosphors for white LEDs application, CaAl₁₂O₁₉:Mn⁴⁺ phosphors have been prepared by a combustion method assisted with GeO₂ flux. The influence of GeO₂ concentration and annealing temperature on the structure and luminescence intensity for the phosphors has been investigated. The mechanism for luminescence enhancement has been discussed. At GeO₂ doping concentration of 1.5 mol%, the red emission intensity increases by 81% under 330 nm UVA excitation. More isolated luminescence center Mn⁴⁺ ions rather than pairs of Mn⁴⁺-Mn²⁺ ions are formed in the lattice with the introduction of GeO₂ at high temperature oxidation, leading to the enhancement of the red emission. A feasible new way to enhance the red emission in CaAl₁₂O₁₉:Mn⁴⁺ phosphor is obtained.     

Thermally stable luminescence and energy transfer in Ce, Mn doped Sr2Mg(BO3)2 phosphor

Sr₂Mg(BO₃)₂:Ce³⁺,Li⁺ and Sr₂Mg(BO₃)₂:Ce³⁺,Li⁺,Mn²⁺ phosphors have been synthesized by conventional solid state reaction technology at 900 °C for 12 h in reducing atmosphere. The phase purity, photoluminescence (PL) properties, thermal stability, energy transfer and luminescent decay curves have been investigated. Sr₂Mg(BO₃)₂:Ce³⁺,Li⁺,Mn²⁺ phosphors show blue and deep-red¹ emission bands. The deep-red emission band is attributed to the energy transfer from Ce³⁺ to Mn²⁺. The fluorescence lifetimes of Ce³⁺ in co-doped sample are shorter than that in single doped one, which confirms that the energy transfer takes place. The phosphors have weak thermal quenching. The luminescence properties of Sr₂Mg(BO₃)₂:Ce³⁺,Li⁺,Mn²⁺ make the phosphor a new bicolor emitting material.     

Luminescence characterization of (Ca1−xSrx)(S1−ySey):Eu,M (M = Sc and Y) for high color rendering white LED

The highly efficient red phosphors (Ca_1−xSr_x)(S_1−ySe_y):Eu²⁺,M³⁺ (M = Sc and Y) were prepared, starting from CaCO₃, SrCO₃, Eu₂O₃, Sc₂O₃, Y₂O₃, S, and SeO₂ with a flux, by a conventional solid-state reaction. The optimized red phosphors converted 11.8% (Sc³⁺) and 11.7% (Y³⁺) of the absorbed blue light into luminescence. These quantum values are much higher than Q = 3.0% of CaS:Eu²⁺. For the fabrication of light-emitting diodes (LEDs), the prepared phosphors were coated with MgO from non-aqueous solution to overcome their weakness against moisture. White LEDs were fabricated by pasting the prepared red phosphors and the yellow YAG:Ce³⁺ phosphor on an InGaN blue chip (λ_ems = 446.5 nm). The incorporation of the red phosphor to the YAG:Ce³⁺ phosphor resulted in an improved color rendering index (Ra) from 70 to 80.     

Synthesis and photoluminescence properties of MgAl2O4:Mn hexagonal nanoplates

MgAl₂O₄:Mn²⁺ hexagonal nanoplates have been synthesized via a simple two-step method. The nanoplates have uniform hexagonal morphology with an average edge length of 1 μm and thickness of 30 nm. X-ray diffraction and various microscopic techniques indicate that MgAl₂O₄:Mn²⁺ nanoplates are single-crystal with multilayered morphology. The formation mechanism has also been discussed. Photoluminescence (PL) spectrum of the MgAl₂O₄:Mn²⁺ nanoplate shows a broad green emission band centered at 568 nm, which is assigned to the ⁴T₁ → ⁶A₁ transition of Mn²⁺ ion. The MgAl₂O₄:Mn²⁺ nanoplate is a promising candidate for efficient nanoscale optical material.     

White light generation in Al2O3:Ce:Tb:Mn films deposited by ultrasonic spray pyrolysis

Aluminium oxide (Al₂O₃) films doped with CeCl₃, TbCl₃ and MnCl₂ were deposited at 300 °C with the ultrasonic spray pyrolysis technique. The films were analysed using the X-ray diffraction technique and they exhibited a very broad band without any indication of crystallinity, typical of amorphous materials. Sensitization of Tb³⁺ and Mn²⁺ ions by Ce³⁺ ions gives rise to blue, green and red simultaneous emission when the film activated by such ions is excited with UV radiation. The overall efficiency of such energy transfer results to be about 85% upon excitation at 312 nm. Energy transfer from Ce³⁺ to Tb³⁺ ions through an electric dipole-quadrupole interaction mechanism appears to be more probable than the electric dipole-dipole one. A strong white light emission for the Al₂O₃:Ce³⁺(1.3 at.%):Tb³⁺(0.2 at.%):Mn²⁺(0.3 at.%) film under UV excitation is observed. The high efficiency of energy transfer from Ce³⁺ to Tb³⁺ and Mn²⁺ ions, resulting in cold white light emission (x = 0.30 and y = 0.32 chromaticity coordinates) makes the Ce³⁺, Tb³⁺ and Mn²⁺ triply doped Al₂O₃ film an interesting material for the design of efficient UV pumped phosphors for white light generation.