沥青基短切碳纤维的表面臭氧改性对碳纤维/天然橡胶复合材料结构与性能的影响

研究沥青基短切碳纤维表面臭氧改性时间及碳纤维用量对碳纤维/天然橡胶（NR）复合材料结构与性能的影响。结果表明：随着臭氧处理时间的延长,碳纤维表面涂覆层逐渐减少直至消失,表面粗糙度明显增大,与NR的界面粘合明显改善;与添加未处理碳纤维的NR硫化胶相比,臭氧改性碳纤维/NR硫化胶的拉伸强度大幅提高;随着改性碳纤维（臭氧处理3.5 h）用量的增大,碳纤维/NR硫化胶的拉伸强度、拉断伸长率在碳纤维用量为5份时出现最大值; 添加5份改性碳纤维（臭氧处理3.5 h）可使NR硫化胶的初始分解温度提高10 ℃。     

碳纤维表面处理对碳纤维/NR复合材料性能的影响

试验研究碳纤维表面处理对碳纤维/NR复合材料性能的影响。结果表明,碳纤维经表面处理后表面沟槽加宽、加深,粗糙度增大,可改善其与橡胶基体的粘合性。与未处理碳纤维/NR复合材料相比,浓硝酸表面处理3h的碳纤维/NR复合材料的拉伸强度提高46%,耐磨性提高5%;300℃×20min高温氧化表面处理碳纤维/NR复合材料的拉伸强度和耐磨性均提高38%;浓硝酸处理1h后再加1.3份钛酸酯偶联剂的碳纤维/NR复合材料拉伸强度提高25%;碳纤维经浓硝酸处理1h后再进行表面浸胶,复合材料的耐磨性提高34%。     

微波辅助改性海泡石补强天然橡胶的研究

采用微波辅助酸活化工艺和硅烷偶联剂KH570（简称KH570）表面修饰得到改性海泡石,将其与炭黑N550并用补强天然橡胶（NR）,研究海泡石改性前后的结构变化及其与炭黑N550并用对NR复合材料性能的影响。结果表明：KH570与酸活化海泡石表面—OH反应并包覆其表面,改性海泡石的亲油接触角减小,改性海泡石与NR的相容性提高;随着改性海泡石用量的增大,改性海泡石/炭黑N550/NR复合材料的硫化时间延长,拉伸强度和拉断伸长率增大,压缩永久变形先减小后增大,耐老化性能提高,储能模量、损耗模量和损耗因子呈减小趋势;当改性海泡石/炭黑N550用量比为30/10时,改性海泡石/炭黑N550/NR复合材料的拉伸强度和拉断伸长率最大。     

硬脂酸系表面改性剂对碳酸钙晶须/天然橡胶复合材料性能的影响

试验研究3种硬脂酸系表面改性剂对碳酸钙晶须/天然橡胶(NR)复合材料物理性能和热稳定性的影响。结果表明:经表面改性剂处理的碳酸钙晶须表面性能提高,与NR界面作用增强;改性碳酸钙晶须/NR复合材料的定伸应力、拉伸强度和撕裂强度均比未改性时有所增大;硬脂酸改性的复合材料综合物理性能较优,硬脂酸或硬脂酸钠改性的复合材料热稳定性提高。     

白炭黑粒子间距对天然橡胶复合材料性能的影响

分别采用不同分子链长度的改性剂乙二醇二缩水甘油醚、丁二醇二缩水甘油醚、己二醇二缩水甘油醚和聚乙二醇二缩水甘油醚(PEGDGE)对白炭黑进行隔离改性,研究改性白炭黑对天然橡胶(NR)复合材料性能的影响。结果表明:与未改性白炭黑填充的NR复合材料相比,改性白炭黑填充的NR复合材料的t10和t90缩短,FL和储能模量(G′)减小,硬度降低,拉伸强度、拉断伸长率和撕裂强度提高;当改性剂为PEGDGE(回转半径为1.11 nm)时,改性白炭黑的粒子间距最大,分散性最好,NR复合材料的交联密度最大,G′和损耗因子最小,物理性能最佳。     

酚醛树脂改性淀粉/NR复合材料的性能研究

采用间苯二酚-甲醛(RF)树脂改性淀粉,通过乳液共沉法制备淀粉/NR复合材料,研究改性淀粉用量对复合材料性能的影响,并与相同体积分数的炭黑和偶联剂Si69改性的白炭黑填充的NR复合材料进行对比。试验结果表明,RF树脂的加入增强了淀粉与NR之间的交联作用,提高了淀粉/NR复合材料的物理性能;当淀粉用量为20份、经3.6份RF树脂改性后,复合材料的综合性能最佳;随着改性淀粉用量的增大,复合材料的硬度和300%定伸应力增大。当填料体积分数相同时,改性淀粉对NR的补强效果与炭黑接近,且优于白炭黑。     

离子液改性白炭黑对天然橡胶性能的影响

采用一定用量的离子液氯化1-烯丙基-3-甲基咪唑（AMI）对白炭黑进行表面改性,用差示扫描量热仪对改性白炭黑进行了表征,考察了改性白炭黑对天然橡胶（NR）复合材料硫化特性、力学性能和动态力学性能的影响。结果表明,AMI和白炭黑之间存在较强的相互作用;当白炭黑用量少于30份时,随着改性白炭黑用量的增加,混炼胶的正硫化时间缩短,硫化速率提高;当白炭黑用量为30份时,NR复合材料的力学性能最佳,增强作用最明显,与不加改性白炭黑的试样相比拉伸强度增加了30.8%,撕裂强度提高了188.9%,磨耗体积减小了76.0%;与白炭黑填充的NR硫化胶相比,改性白炭黑填充的NR硫化胶的玻璃化转变温度升高,储能模量增大,改性白炭黑与NR之间的相互作用较白炭黑更强。     

无机填料的表面处理及其在导热天然橡胶复合材料中的应用

用季戊四醇、丙三醇和钛酸酯偶联剂分别对氧化铝、氧化镁和高岭土进行表面改性,并将改性填料填充天然橡胶(NR)制备了导热复合材料,考察了表面处理剂种类及其用量对无机填料的影响,并研究了季戊四醇改性氧化铝填充NR复合材料的硫化特性、物理机械性能和导热性能.结果表明,3种填料中季戊四醇的改性效果最好,且其用量为1.0～1.5份时对氧化铝的改性效果最佳;随着改性氧化铝填充量的增加,复合材料的最大转矩、300%定伸应力、拉伸强度和热导率均增大,当其用量为60份时,改性氧化铝填充NR复合材料的热导率比未填充NR复合材料提高了23.9%.     

固相改性有机蒙脱土/炭黑/NR复合材料的耐老化性能研究

试验研究固相改性有机蒙脱土(GMMT)/炭黑/NR复合材料的耐热氧、耐臭氧和耐紫外光老化性能。结果表明,与炭黑/NR复合材料相比,GMMT/炭黑/NR复合材料热氧、臭氧和紫外光老化前后的综合物理性能均较优;X射线衍射分析表明,老化前后GMMT/炭黑/NR复合材料的层间距变化不大,老化过程不影响GMMT在NR基体中的分散。     

偶联剂Si69改性白炭黑对NR/SSBR并用胶性能的影响

试验研究偶联剂Si69用量和白炭黑改性方法对白炭黑填充NR/SSBR并用胶性能的影响.结果表明,当采用直接加入法改性白炭黑时,随着偶联剂Si69用量的增大,Payne效应减弱,NR/SSBR并用胶的t10延长,t90缩短,硫化胶的物理性能提高,偶联剂Si69用量以4 5份为宜.与直接加入法改性白炭黑填充并用胶相比,预处理法改性白炭黑填充并用胶的Payne效应减弱,拉伸强度和撕裂强度增大;高温静置处理法改性白炭黑填充并用胶的定伸应力、拉伸强度和损耗模量增大.     

短切CF增强TPEE热塑性复合材料的注射成型及力学性能研究

以热塑性聚酯弹性体(TPEE)为基体材料,8 mm短切碳纤维(CF)为增强材料,制备CF/TPEE复合材料。材料通过双螺杆挤出系统混合塑化、挤出造粒后,再经过注塑成型制备成标准拉伸试样,通过力学性能测试及微观结构观察,系统研究了碳纤维含量和等离子表面处理对CF/TPEE复合材料拉伸性能的影响。结果表明,当碳纤维含量为20%时,CF/TPEE复合材料的拉伸强度最大,为39.08 MPa;相比于纯TPEE,其拉伸强度提高了217%;经过等离子表面处理后,拉伸强度进一步提高了5%。结合拉伸后断面的SEM图发现,注塑试样表层碳纤维取向度高,而近中区和中心层取向度相对较低,这是注射CF/TPEE复合材料拉伸性能提高效应不明显的主要原因。     

混炼方式对螺旋纳米碳纤维增强天然橡胶复合材料力学性能的影响

采用干法和湿法两种混炼工艺制备了螺旋纳米碳纤维(HCNFs)/炭黑(CB)/天然橡胶(NR)复合材料,通过扫描电镜、拉伸试验机和应变扫描仪分别对所制备复合材料的界面形貌、力学性能和Payne效应进行了测试分析,考察了混炼方式对复合材料宏观力学性能及Payne效应的影响。结果表明,与纯CB填料相比,在干湿两种混炼方式下,添加适量的HCNFs(1～6份)能提高HCNFs/CB/NR复合材料的300%定伸应力、扯断伸长率、拉伸强度和硬度。与干法混炼相比,湿法混炼能明显增强HCNFs/CB/NR复合材料的Payne效应,并提升在HCNFs高添加量(2～6份)条件下的拉伸强度和扯断伸长率,这主要源于湿法混炼能够有效改善HCNFs在橡胶基质中的分散性。     

Effect of coal gangue/carbon black/multiwall carbon nanotubes hybrid fillers on the properties of natural rubber composites

The objective of this study was to investigate three kinds of filler with completely different morphology on mechanical properties of natural rubber (NR). Coal gangue (CG) are derived from natural deposits are composed principally by illite and quartz. CG, carbon black (CB), and multiwalled carbon nanotube (CNT) were used as hybrid fillers in NR. CNTs were dispersed into NR latex by ultrasonic irradiation and then the mixed latex were coagulated to obtain the CNTs/NR masterbatch, then mechanical mixing method was employed to prepare the CG/CB/CNTs/NR composites. The addition of CG, CB, and CNTs to NR was varied with the total filler loading fixed at 35 phr. The mechanical properties of NR composites were studied in terms of tensile and dynamic mechanical analysis (DMA). The results showed that the tensile strength and modulus 300% (M300) of all hybrid samples were higher than the composites only loaded CG; and the highest tensile strength of NR loaded with hybrid fillers achieved at sample of loading amount of CG 17.5, CB 15.5, and CNTs 2 phr, whose M300 and elongation at break was obviously higher than that of only CB loaded NR composites; The inclusion CG improves the tensile strength of NR without the sacrifice of its extensibility, while CB and CNTs brings together the enhancement in the ultimate strength and the reduction in the extensibility. DMA results revealed that the existence of CG can improve the dispersion of CB and CNTs in NR matrix. POLYM. COMPOS., 37:3083–3092, 2016. © 2015 Society of Plastics Engineers     

Carbon nanotubes/carbon black synergistic reinforced natural rubber composites

Abstract

Carbon black (CB) and carbon nanotubes (CNTs) filled natural rubber (NR) composites were prepared. In order to overcome the dispersion of CNTs in rubber matrix, the surface modification of CNTs with bis-(γ-triethoxysilylpropyl)-tetrasulphide (Si-69) was undertaken, and a two-step mixing process, i.e. the use of twin roll mill followed by mixing in a Haake Banbury mixer (TR-THM) was used. The structure and mechanical properties were investigated. The results show that the Si-69 treated CNTs (S-CNTs) were dispersed in the rubber matrix uniformly. Compared with CB/NR composites without CNTs, the S-CNTs/CB/NR composites have better mechanical properties. When the ratio of S-CNTs/CB/NR was 5 : 20 : 100, the tear strength was improved by ～60%, and the mechanical properties reached a maximum. Dynamical mechanical analysis (DMA) reveals that with increasing content of CNT, the elastic modulus of composites at room temperature increases, and the maximum loss tangent and the corresponding glass transition temperature of composites decrease.     

表面改性碳纳米管/天然橡胶复合材料的制备及性能研究

采用多巴胺对多壁碳纳米管(MWCNTs)进行非共价改性,得到多巴胺改性MWCNTs(简称PCNT)。将PCNT作为填料加入天然胶乳中制备PCNT/天然橡胶(NR)复合材料,并研究其性能。透射电子显微镜(TEM)分析结果表明MWCNTs经过多巴胺改性后在水中的分散效果明显改善。PCNT/NR复合材料的拉伸强度和撕裂强度明显提高,拉伸强度由22.7 MPa升至28.4 MPa,撕裂强度由26 kN·m^-1升至40 kN·m^-1。多巴胺用量适当的PCNT在NR基体中分散更均匀,填料与橡胶的相互作用较强,能够形成较好的填料网络结构,PCNT/NR复合材料的表面电阻显著降低。     

石墨和碳纤维改性聚酰亚胺复合材料的导热性能

以石墨、碳纤维(CF)、聚酰亚胺(PI)三元复合材料为研究对象,考察了CF体积含量对PI三元复合材料导热性能的影响,并采用了拟二元体系模型探讨了石墨和CF填充PI复合材料的协同效应。结果表明,CF的加入可以提高复合材料的力学性能：拉伸强度呈现先升高后降低的趋势,当CF含量为11.8 %（体积分数,下同）时,拉伸强度可达66.37 MPa;弯曲强度随着CF体积含量的增而增加,当CF含量为24.6 %时,弯曲强度可达103.3 MPa。复合材料热导率呈非线性增长,表明石墨和CF间存在协同效应;当CF含量为34.1 %时,环境扫描电子显微镜分析表明,CF与石墨能很好地搭接,增大了传热面积,复合材料热导率可达0.512 W/(m·K),约是其计算值的2倍。     

碳纤维增强尼龙66复合材料的制备及性能

采用双螺杆挤出机熔融共混法制备了碳纤维(CF)增强尼龙66复合材料(PA66/CF),对其结构进行了表征,并研究了其力学性能。扫描电镜照片显示,在PA66/CF复合材料中,CF与PA66基体充分粘结在一起,其微观形貌表明,体系中碳纤长度为0.5~0.7 mm。力学性能测试发现,与尼龙66相比,PA66/CF复合材料各项力学性能指标均有大幅度提高。当加入4束碳纤维时,PA66/CF复合材料力学性能最佳,该复合材料的拉伸强度为200.2 MPa,与PA66相比提高了113.2 MPa;弯曲强度为280.2 MPa,比PA66提高了190.3 MPa;弯曲模量为13560.8 MPa,比PA66提高了10628.7 MPa;冲击强度为14.8 kJ/m^2,比与PA66提高了6.3 kJ/m^2。该PA66/CF复合材料密度较小、力学性能优良,可以广泛应用于风电叶片、发动机罩盖、仪表盘、车尾门等产品当中。     

Tailoring Carbon Fiber/Carbon Nanotubes Interface to Optimize Mechanical Properties of Cf‐CNTs/SiC Composites

C_f/SiC composites were fabricated using fiber coatings including CNTs and matrix infiltration using the polymer impregnation and pyrolysis process. Interface between fiber and CNTs (CF/CNTs) was tailored to optimize mechanical properties of hybrid composites. The tailored interphases, such as Pyrocarbon (PyC) and PyC/SiC, protect fibers from degradation during the growth of CNTs successfully. Hybrid composites with well‐tailored CF/CNTs interface displayed significantly increased mechanical strength (352 ± 21 MPa) compared with that (34 ± 3 MPa) of composites reinforced with CNTs, which grown on carbon fibers directly. The interfacial bonding strength of hybrid composites was improved and optimized by tailoring the CF/CNTs interface. Interfacial failure modes were studied, and a firm interface bonding at the joint where CNTs grown was observed.     

炭黑/煤矸石/碳纳米管复合填料体系对天然橡胶性能的影响研究*

利用硝酸氧化法对碳纳米管(CNTs)进行纯化,并用环氧天然橡胶(ENR)进行改性处理。结合胶质量分数测定结果表明, ENR用量15%(质量)时效果最佳。采用胶乳凝聚法制备CNTs/天然橡胶(NR)母料。煤矸石粉(CG)经高温煅烧和表面改性处理。 将CNTs/天然橡胶(NR)母料、CG和炭黑(CB)通过机械混炼法与天然橡胶及配合剂混合,制备CB/CG/CNTs/NR复合材料,并对复合材料进行硫化特性及物理机械性能。结果表明： CNTs延迟硫化效应明显;相比炭黑,CG对硫化具有促进作用。硫化特性和甲苯溶胀法测定结果表明,在填料份数相同的条件下,单独由CB填充的NR有最大的交联密度,CNTs对交联密度影响不明显。物理机械性能测试结果表明,当CG：CB：CNTs=17.5:16.5:1(Phr)时,NR硫化胶的300%定伸应力和扯断伸长率明显高于单独由CB填充NR,而拉伸强度与之接近,复合填料样填充NR具有较好的综合性能。扫描电镜测试结果表明,复合填料在NR基体中分布均匀。     

Effects of novolac resin modification on mechanical properties of carbon fiber/epoxy composites

The epoxy resin matrix of carbon fiber (CF)‐reinforced epoxy composites was modified with novolac resin (NR) to improve the matrix‐dominated mechanical properties of composites. Flexural strength, interlaminar shear strength (ILSS), and impact strength were measured with unfilled, 7 wt% NR, 13 wt% NR, and 18 wt% NR filled to epoxy to identify the effect of adding NR on the mechanical properties of composites. The results showed that both interfacial and impact properties of composites were improved except for flexural property. The largest improvement in ILSS and impact strength were obtained with 13 wt% loading of NR. ILSS and impact strength were improved by 7.3% and 38.6%, respectively, compared with the composite without NR. The fracture and surface morphologies of the composite specimens were characterized by scanning electron microscopy. Intimate bonding of the fibers and the matrix was evident with the content of 7–13 wt% NR range. Decrease of crosslinking density and formation of NR transition layer were deduced with adding NR. POLYM. COMPOS., 2011. © 2010 Society of Plastics Engineers