Molecular dynamics simulation of dislocation nucleation and motion at γ/γ′ interface in Ni-based superalloy

Molecular dynamics simulations are conducted on the dislocation behavior at the apices and edges of cuboidal Ni₃Al precipitate in a pure Ni matrix, or the idealized γ/γ′ microstructure in a Ni-based superalloy. A tensile simulation of the [001] direction is implemented with a periodic cell that has eight cubic precipitates in order to investigate the nucleation site of dislocation in the idealized microstructure with no defects other than the γ/γ′ interfaces. The effect of residual internal stresses on the stability of the interfaces is also discussed. Other simulations are conducted on the behavior of edge dislocations nucleated from a free surface and proceeding in the γ matrix toward γ′ precipitates under shear force. Dislocation pinning at γ′ precipitates, bowing-out in the γ channel, pile-up and nucleation of superdislocation in the γ′ precipitate are simulated and inspected in detail. Discussions on the size of the γ/γ′ microstructure and the sharpness of the edge of the γ′ precipitate are also presented.     

Chromatographic and non‐chromatographic characterization of poly‐α‐olefins

Both chromatographic and non‐chromatographic techniques were used in the characterization and identification of poly‐α‐olefins. Synthetic base oils, although produced from the same raw material, exhibit different physico‐chemical properties. Their mutual miscibility and behaviour in final engine oils may be predicted from data collected through classical physico‐chemical analysis, simulated distillation chromatography as well as inverse gas chromatography. Copyright © 2007 John Wiley & Sons, Ltd.     

Poly‐α‐olefin‐based synthetic lubricants: a short review on various synthetic routes

This paper reviews various synthetic protocols for poly‐α‐olefin (PAO) synthetic lubricant base stocks that have evolved over the years. Apart from conventional Lewis acid catalysts known for the synthesis of poly‐α‐olefins, such as aluminium trichloride and boron trifluoride, several new catalysts such as metallocenes and ionic liquids have been reported by various researchers. With increasing options of catalytic processes available, it is now possible to produce tailor made PAOs and thus control the properties of the end products, such as viscosity and the viscosity index. Although 1‐decene is the most widely used monomer for PAO application, researchers have used a wide range of monomers from 1‐hexene to 1‐tetradecene and internal olefins in some cases. Copyright © 2011 John Wiley & Sons, Ltd.     

A high-resolution electron microscopic study of defects in sodium β′″-alumina

A high-resolution electron-microscopic study of sodium β′″-alumina, a polytype of the more-widely-studied sodium β- and β″-alumina, has been undertaken using the 600 kV instrument at Cambridge University. Images revealed the loss of sodium-containing planes, which had caused crystals to collapse and shear into defect layers. A model for the structure of these defects is proposed, based on the use of computed images and by comparison with high-resolution images of silver β″-alumina.     

Characterization of the μ and P phase precipitates in the CMSX‐4 single crystal superalloy

A combination of scanning electron microscopy (SEM), transmission electron microscopy (TEM) and scanning‐transmission electron microscopy (STEM) using high‐angle annular‐dark‐field (HAADF) imaging, focussed ion beam‐ scanning electron microscopy (FIB‐SEM) tomography, selected area electron diffraction with beam precession (PED), as well as spatially resolved energy‐dispersive X‐ray spectroscopy (EDS) and electron energy loss spectroscopy (EELS), was used to investigate topologically close‐packed (TCP) phases, occurring in the CMSX‐4 superalloy subjected to high temperature annealing and creep deformation. Structural and chemical analyses were performed to identify the TCP phases and provide information concerning the compositional partitioning of elements between them. The results of SEM and FIB‐SEM tomography revealed the presence of merged TCP particles, which were identified by TEM and PED analysis as coprecipitates of the μ and P phases. Inside the TCP particles that were several micrometres in size, platelets of alternating μ and P phases of nanometric width were found. The combination of STEM‐HAADF imaging with spatially resolved EDS and EELS microanalysis allowed determination of the significant partitioning of the constituent elements between the μ and P phases.     

3D reconstruction of prior β grains in friction stir–processed Ti–6Al–4V

The prior β grain structure and orientations in the central stir zone of friction stir–processed Ti–6Al–4V were reconstructed from measured α phase orientations obtained by three‐dimensional serial sectioning in a dual‐beam focused ion beam scanning electron microscope. The data were processed to obtain the α colony and β grain size distributions in the volume. Several β grains were individually analysed to determine the total number of unique α variants and the respective volume fractions of each. The analysis revealed that some grains experienced overwhelming variant selection (i.e. one variant dominated) whereas other β grains contained a more evenly distributed mixture of all 12 variants.     

Measurement of translation component at ordered interfaces by weak-beam α-fringe electron microscopy

Lattice translations at a stacking fault and a twin boundary were measured from fringe shifts at a set of common weak-beam diffraction conditions (weak-beam α-fringe imaging) in stainless steel SUS316. It is suggested that the present technique is applicable in determining the translation component between neighbouring crystals with coincidence related boundaries.     

Role of spermatogonial stem cells extract in transdifferentiation of 5‐Aza‐2′‐deoxycytidine‐treated bone marrow mesenchymal stem cells into germ‐like cells

As one of the induced pluripotent stem cells (iPSCs) methods, spermatogonial stem cells (SSC_S) extract is considered as new approach in stem cell therapy of infertility. 5‐aza‐2′‐deoxycytidine (5‐aza‐dC) inhibits methyltransferase enzyme, and induces gene reprogramming; herein, the effects of SSC_S extract incubation in 5‐aza‐dC‐treated bone marrow mesenchymal stem cells (BMMSCs) has been surveyed. BMMSCs were isolated from femurs of three to four weeks old male NMRI mice, and the cells at passage three were treated with 2 µM 5‐aza‐dC for 72 hours. SSCs were isolated, cultured, and harvested at passage three to collect SSC_S extract; BMMSCs were then incubated with SSC_S extract in the three time periods: 72 hours, one week and two weeks. There were five groups: control, sham, extract, 5‐aza‐dC and extract‐5‐aza‐dC. After one week of incubation, flow cytometry and real‐time polymerase chain reaction (PCR) exhibited high levels of expression for β1‐ and α6‐integrins and promyelocytic leukaemia zinc finger (PLZF) in extract and extract‐5‐aza‐dC groups (P < 0.05 vs. control and 5‐aza‐dC), and cells in these two groups had two forms of morphology, round and fusiform, similar to germ‐like cells. 5‐aza‐dC had no significant effects during the three time periods of evaluation. These data disclose the effectiveness of SSCs extract incubation in transdifferentiation of BMMSCs into germ‐like cells; this strategy could introduce a new approach for treatment of male infertility in clinic. Microsc. Res. Tech. 79:365–373, 2016. © 2016 Wiley Periodicals, Inc.     

Sliding wear behaviour of Ca α-sialon ceramics at 600 °C in air

As an extension of a previous investigation on the wear behaviour of Ca α-sialon ceramics of differing microstructures at room temperature, wear testing was conducted at 600 °C in air to explore the effects of microstructure, contact pressure and sliding speed on the wear behaviour. Under all loading conditions from 1 MPa to 1 GPa, a constant high friction coefficient was observed and a severe wear process was dominant, in which the sliding contact induced cracks were observed in different microstructures. Wear particles were generated along the wear track, but no tribofilm was detected. Increasing the sliding speed from 10 to 23 cm/s was found to significantly increase wear rate. However, variations in microstructure had little impact. That is, large elongated-grained α-sialon exhibited only a slightly lower wear rate than fine equiaxed-grained α-sialon.     

Effect of indirubin‐3‐monoxime against lung cancer as evaluated by histological and transmission electron microscopic studies

The aim of this study is to evaluate the antitumor effect of indirubin‐3‐monoxime and its mode of action in benzo(α)pyrene [B(α)P] induced lung cancer in A/J mice. Light microscopic examination of lung sections of [B(α)P] induced lung cancer mice revealed the presence of adenocarcinoma characterized by extensive proliferation of alveolar epithelium and loss of alveolar spaces. The control lung tissue showed a normal architecture with clear alveolar spaces. Interestingly the indirubin‐3‐monoxime treated groups showed the reduced adenocarcinoma with appearance of alveolar spaces. Transmission Electron Microscopic (TEM) studies of lung sections of [B(α)P] induced lung cancer mice showed the presence of phaemorphic cells with dense granules and increased mitochondria. The lung sections of mice treated with indirubin‐3‐monoxime showed the presence of shrunken, fragmented, and condensed nuclei implying apoptosis. The effects were dose dependent and prominent in 10 mg/kg/5 d/week groups suggesting the therapeutic role of indirubin analogue against this deadly human malignancy. Here, our results indicate that indirubin‐3‐monoxime brings antitumor effect against [B(α)P] induced lung cancer by its apoptotic action in A/J mice. Microsc. Res. Tech. 73:1053–1058, 2010. © 2010 Wiley‐Liss, Inc.     

Reflection electron imaging and spectroscopy studies of aluminium metal reduction at α-aluminium oxide (0,1,2) surfaces

Cleaved α-aluminium oxide (0,1,2) surfaces are studied using combined techniques of scanning reflection electron microscopy and reflection electron energy-loss spectroscopy. An α-aluminium oxide (0,1,2) surface can terminate with a layer of either oxygen or Al atoms depending on where the bonds break. Aluminium metal can be reduced only from the domains initially terminated with oxygen by an intensive electron beam. The interpretation of this damage effect is based on the desorption process of oxygen atoms after Auger decay. The resistance to beam damage of the domains initially terminated with Al is found to be due to the protection of the surface adsorbed amorphous oxygen layer.     

Detection of CD133 (prominin‐1) in a human hepatoblastoma cell line (HuH‐6 clone 5)

We examined CD133 distribution in a human hepatoblastoma cell line (HuH‐6 clone 5). We directly observed the cultured cells on a pressure‐resistant thin film (silicon nitride thin film) in a buffer solution by using the newly developed atmospheric scanning electron microscope (ASEM), which features an open sample dish with a silicon nitride thin film window at its base, through which the scanning electron microscope beam scans samples in solution, from below. The ASEM enabled observation of the ventral cell surface, which could not be observed using standard SEM. However, observation of the dorsal cell surface was difficult with the ASEM. Therefore, we developed a new method to observe the dorsal side of cells by using Aclar® plastic film. In this method, cells are cultured on Aclar plastic film and the dorsal side of cells is in contact with the thin silicon nitride film of the ASEM dish. A preliminary study using the ASEM showed that CD133 was mainly localized in membrane ruffles in the peripheral regions of the cell. Standard transmission electron microscopy and scanning electron microscopy revealed that CD133 was preferentially concentrated in a complex structure comprising filopodia and the leading edge of lamellipodia. We also observed co‐localization of CD133 with F‐actin. An antibody against CD133 decreased cell migration. Methyl‐β‐cyclodextrin treatment decreased cell adhesion as well as lamellipodium and filopodium formation. A decrease in the cholesterol level may perturb CD133 membrane localization. The results suggest that CD133 membrane localization plays a role in tumor cell adhesion and migration. Microsc. Res. Tech. 76:844–852, 2013. © 2013 Wiley Periodicals, Inc.     

Increased androgen receptor and remodeling in the prostatic stroma after the inhibition of 5‐alpha reductase and aromatase in gerbil ventral prostate

Prostate require high levels of steroidogenic enzymes such as 5α‐reductase (5α‐r) and Aromatase (Aro) for the formation of active steroids. Dihydrotestosterone (DHT), the prostate dominant androgen, is converted from testosterone (T) by the action of 5α‐r. Aro provides an alternative pathway for estrogen, via T aromatization. Since prostatic maintenance is dependent on both reciprocal stromal–epithelial interaction and regulation by steroids, this study aimed to elucidate what the absence of 5α‐r and Aro enzymes provokes in the prostate microenvironment after their long‐term inhibition. Data obtained 1 day after the 30 consecutive days of enzymatic inhibition with Finasteride (5α‐r inhibitor) and Letrozole (Aro inhibitor) demonstrated a marked stromal remodeling, with an increased deposition of extracellular matrix (ECM) proteins besides androgen receptor (AR) overexpression in the three phases of postnatal development analyzed. The subepithelial area of acini from ventral prostate presented collagen and reticular fibers accumulation, besides various altered and active fibroblasts. The AR content immunostaining was elevated after enzymatic inhibition therapy, mainly in the nuclei of epithelial cells. Similar data were observed in the ventral prostates even 21 days after the end of treatments. Results obtained following the long‐term inhibition of 5α‐r and Aro are relevant and highlight the actions of these enzymes as crucial not only for the maintenance of tissue architecture and ECM arrangement but also for androgen and AR function. The long‐term absence of their action imposes a novel situation on the prostate from which its normal physiology could not be restored by the conclusion of the treatments. Microsc. Res. Tech., 2009. © 2009 Wiley‐Liss, Inc.     

Tool life monitoring during the diamond turning of electroless Ni–P

Diamond tools become severely worn when machining Ni–P plating materials. Tool life monitoring is therefore essential to avoid the deterioration of workpiece quality. In this paper, in order to better detect tool life while the tools are in use, detailed investigations of the cutting force and acoustic emission (AE) measured during diamond turning process have been made. The results of this tool-life testing show that the cutting force and AE supply valuable information on tool failure; the dynamic component of the thrust force fluctuates chaotically when the tool dulls. This phenomenon can be detected using the 1/f^β power spectrum with a spectral exponent of β > 1. On the other hand, the AE amplitude a tends to rise just when chipping occurs on the cutting edge. This feature can be detected by the amplitude distribution spectrum, in which the AE event rate follows the power law a^−m with a scaling exponent of m < 2. Therefore, we can conclude that a spectral exponent of β > 1 and a scaling exponent of m < 2 can be used as the criteria to gauge tool life, because it was observed at the end of the tool life that tool corner had become worn out and that chipping had occurred on the cutting edge.