Fabrication and characterization of 100-nm In/sub 0.53/Ga/sub 0.47/As-In/sub 0.52/Al/sub 0.48/As double-gate HEMTs with two separate gate controls

In this letter, we demonstrate successful operation of 100-nm T-gates double-gate high electron mobility transistors with two separate gate controls (V/sub g1s/ /spl ne/ V/sub g2s/). These devices are fabricated by means of adhesive bonding technique using enzocyclocbutene polymer. The additional gate enables the variation of the threshold voltage V/sub th/ in a wide range from -0.68 to -0.12V while keeping high cutoff frequency f/sub t/ of about 170 GHz and high maximum oscillation frequency f/sub max/ of about 200 GHz. These devices are considered as being very effective for millimeter-wave mixing applications and are promising devices for the fabrication of velocity modulation transistor (VMT) (Sakaki et al., 1982).     

Mixed body bias techniques with fixed V/sub t/ and I/sub ds/ generation circuits

There remains a need to improve sub-1-V CMOS VLSIs with respect to variation in transistor behavior. In this paper, to minimize variation in delay and the noise margin of the circuits in processors, we propose several mixed body bias techniques using body bias generation circuits. In these circuits, either the saturation region of the current between source and drain (I/sub ds/) or the threshold voltage (V/sub t/) of PMOS/NMOS is permanently fixed, regardless of temperature range or variation in process. A test chip that featured these body bias generation circuits was fabricated using a 130-nm CMOS process with a triple-well structure. The mixed body bias techniques which keep the I/sub ds/ of the MOS in the decoder and I/O circuits of a register file fixed and maintain the V/sub t/ of the MOS in both the memory cell and domino circuits of the register file fixed resulted in positive temperature dependence of delay from -40 /spl deg/C to 125 /spl deg/C, 85% reduction of the delay variation compared with normal body bias (NBB) at V/sub DD/ = 0.8 V. In addition, the results using these techniques show a 100-mV improvement in lower operating voltage compared with NBB at -40 /spl deg/C on a 4-kb SRAM.     

Turn-on voltage investigation of GaAs-based bipolar transistors with Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ base layers

The fundamental lower limit on the turn on voltage of GaAs-based bipolar transistors is first established, then reduced with the use of a novel low energy-gap base material, Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/. InGaP/GaInAsN DHBTs (x/spl sim/3y/spl sim/0.01) with high p-type doping levels (/spl sim/3/spl times/10/sup 19/ cm/sup -3/) and dc current gain (/spl beta//sub max//spl sim/68 at 234 /spl Omega///spl square/) are demonstrated. A reduction in the turn-on voltage over a wide range of practical base sheet resistance values (100 to 400 /spl Omega///spl square/) is established relative to both GaAs BJTs and conventional InGaP/GaAs HBTs with optimized base-emitter interfaces-over 25 mV in heavily doped, high dc current gain samples. The potential to engineer turn-on voltages comparable to Si- or InP-based bipolar devices on a GaAs platform is enabled by the use of lattice matched Ga/sub 1-x/In/sub x/As/sub 1-y/N/sub y/ alloys, which can simultaneously reduce the energy-gap and balance the lattice constant of the base layer when x/spl sim/3y.     

The effect of IrO/sub 2/--IrO/sub 2/--Hf--LaAlO/sub 3/ gate dielectric on the bias-temperature instability of 3-D GOI CMOSFETs

We have studied the bias-temperature instability of three-dimensional self-aligned metal-gate/high-/spl kappa//Germanium-on-insulator (GOI) CMOSFETs, which were integrated on underlying 0.18 /spl mu/m CMOSFETs. The devices used IrO/sub 2/--IrO/sub 2/-Hf dual gates and a high-/spl kappa/ LaAlO/sub 3/ gate dielectric, and gave an equivalent-oxide thickness (EOT) of 1.4 nm. The metal-gate/high-/spl kappa//GOI p-and n-MOSFETs displayed threshold voltage (V/sub t/) shifts of 30 and 21 mV after 10 MV/cm, 85/spl deg/C stress for 1 h, comparable with values for the control two-dimensional (2-D) metal-gate/high-/spl kappa/-Si CMOSFETs. An extrapolated maximum voltage of -1.2 and 1.4 V for a ten-year lifetime was obtained from the bias-temperature stress measurements on the GOI CMOSFETs.     

Charge trapping in ultrathin hafnium silicate/metal gate stacks

Charge trapping characteristics of MOCVD HfSi/sub x/O/sub y/ (20% SiO/sub 2/) gate stack of n-MOSFETs during substrate injection have been investigated. Positive constant voltage stress (CVS) and constant current stress (CCS) were applied at the gate of TiN-HfSi/sub x/O/sub y/-SiO/sub 2//p-Si n-MOSFETs having EOT of 2 nm. Significant electron trapping is observed from the positive shift of threshold voltage (/spl Delta/V/sub t/) after stress. Curve fitting of the threshold voltage shift data confirms power law dependence for Hf-silicate gate stacks. Charge pumping measurements for both cases showed significant electron trapping at bulk Hf-silicate while interface trap generation was comparatively insignificant. A turn-around effect is noticed for /spl Delta/V/sub t/ as the stress current and voltage increases under CCS and CVS. Dependence of spatial distribution of charge trapping at shallow traps on stress level in the Hf-silicate film and redistribution of trapped charges during and after removal of stress is possibly responsible for the turn-around effect.     

Low-frequency noise in submicrometer MOSFETs with HfO/sub 2/, HfO/sub 2//Al/sub 2/O/sub 3/ and HfAlO/sub x/ gate stacks

Low-frequency noise measurements were performed on p- and n-channel MOSFETs with HfO/sub 2/, HfAlO/sub x/ and HfO/sub 2//Al/sub 2/O/sub 3/ as the gate dielectric materials. The gate length varied from 0.135 to 0.36 /spl mu/m with 10.02 /spl mu/m gate width. The equivalent oxide thicknesses were: HfO/sub 2/ 23 /spl Aring/, HfAlO/sub x/ 28.5 /spl Aring/ and HfO/sub 2//Al/sub 2/O/sub 3/ 33 /spl Aring/. In addition to the core structures with only about 10 /spl Aring/ of oxide between the high-K dielectric and silicon substrate, there were "double-gate oxide" structures where an interfacial oxide layer of 40 /spl Aring/ was grown between the high-K dielectric and Si. DC analysis showed low gate leakage currents in the order of 10/sup -12/ A(2-5 /spl times/ 10/sup -5/ A/cm/sup 2/) for the devices and, in general, yielded higher threshold voltages and lower mobility values when compared to the corresponding SiO/sub 2/ devices. The unified number-mobility fluctuation model was used to account for the observed 1/f noise and to extract the oxide trap density, which ranged from 1.8 /spl times/ 10/sup 17/ cm/sup -3/ eV/sup -1/ to 1, 3 /spl times/ 10/sup 19/ cm/sup -3/ eV/sup -1/ somewhat higher compared to conventional SiO/sub 2/ MOSFETs with the similar device dimensions. There was no evidence of single electron switching events or random telegraph signals. The aim of this paper is to present a general discussion on low-frequency noise characteristics of the three different high-K/gate stacks, relative comparison among them and to the Si-SiO/sub 2/ system.     

High-temperature thermal stability performance in /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As metamorphic HEMT

We report, to our knowledge, the best high-temperature characteristics and thermal stability of a novel /spl delta/-doped In/sub 0.425/Al/sub 0.575/As--In/sub 0.65/Ga/sub 0.35/As--GaAs metamorphic high-electron mobility transistor. High-temperature device characteristics, including extrinsic transconductance (g/sub m/), drain saturation current density (I/sub DSS/), on/off-state breakdown voltages (BV/sub on//BV/sub GD/), turn-on voltage (V/sub on/), and the gate-voltage swing have been extensively investigated for the gate dimensions of 0.65/spl times/200 /spl mu/m/sup 2/. The cutoff frequency (f/sub T/) and maximum oscillation frequency (f/sub max/), at 300 K, are 55.4 and 77.5 GHz at V/sub DS/=2 V, respectively. Moreover, the distinguished positive thermal threshold coefficient (/spl part/V/sub th///spl part/T) is superiorly as low as to 0.45 mV/K.     

The thermal stability of one-transistor ferroelectric memory with Pt-Pb/sub 5/Ge/sub 3/O/sub 11/-Ir-poly-SiO/sub 2/-Si gate stack

The thermal stability of one-transistor ferroelectric nonvolatile memory devices with a gate stack of Pt-Pb/sub 5/Ge/sub 3/O/sub 11/-Ir-Poly-SiO/sub 2/-Si was characterized in the temperature range of -10/spl deg/C to 150/spl deg/C. The memory windows decrease when the temperatures are higher than 60/spl deg/C. The drain currents (I/sub D/) after programming to on state decrease with increasing temperature. The drain currents (I/sub D/) after programming to off state increase with increasing temperature. The ratio of drain current (I/sub D/) at on state to that at off state drops from 7.5 orders of magnitude to 3.5 orders of magnitude when the temperature increases from room temperature to 150/spl deg/C. On the other hand, the memory window and the ratio of I/sub D/(on)/I/sub D/(off) of the one-transistor memory device displays practically no change when the temperature is reduced from room temperature to -10/spl deg/C. One-transistor (1T) memory devices also show excellent thermal imprint properties. Retention properties of 1T memory devices degrade with increasing temperature over 60/spl deg/C.     

Characteristics of In/sub x/Al/sub 1-x/N-GaN high-electron mobility field-effect transistor

GaN-based field effect transistors commonly include an Al/sub x/Ga/sub 1-x/N barrier layer for confinement of a two-dimensional electron gas (2DEG) in the barrier/GaN interface. Some of the limitations of the Al/sub x/Ga/sub 1-x/N-GaN heterostructure can be, in principle, avoided by the use of In/sub x/Al/sub 1-x/N as an alternative barrier, which adds flexibility to the engineering of the polarization-induced charges by using tensile or compressive strain through varying the value of x. Here, the implementation and electrical characterization of an In/sub x/Al/sub 1-x/-GaN high electron mobility transistor with Indium content ranging from x=0.04 to x=0.15 is described. The measured 2DEG carrier concentration in the In/sub 0.04/Al/sub 0.96/N-GaN heterostructure reach 4/spl times/10/sup 13/ cm/sup -2/ at room temperature, and Hall mobility is 480 and 750 cm/sup 2//V /spl middot/ s at 300 and 10 K, respectively. The increase of Indium content in the barrier results in a shift of the transistor threshold voltage and of the peak transconductance toward positive gate values, as well as a decrease in the drain current. This is consistent with the reduction in polarization difference between GaN and In/sub x/Al/sub 1-x/N. Devices with a gate length of 0.7 /spl mu/m exhibit f/sub t/ and f/sub max/ values of 13 and 11 GHz, respectively.     

A 0.5-V 1-/spl mu/W successive approximation ADC

A successive approximation analog-to-digital converter (ADC) is presented operating at ultralow supply voltages. The circuit is realized in a 0.18-/spl mu/m standard CMOS technology. Neither low-V/sub T/ devices nor voltage boosting techniques are used. All voltage levels are between supply voltage V/sub DD/ and ground V/sub SS/. A passive sample-and-hold stage and a capacitor-based digital-to-analog converter are used to avoid application of operational amplifiers, since opamp operation requires higher values for the lowest possible supply voltage. The ADC has signal-to-noise-and-distortion ratios of 51.2 and 43.3 dB for supply voltages of 1 and 0.5 V, at sampling rates of 150 and 4.1 kS/s and power consumptions of 30 and 0.85 /spl mu/W, respectively. Proper operation is achieved down to a supply voltage of 0.4 V.     

Ultrathin Al/sub 2/O/sub 3/ and HfO/sub 2/ gate dielectrics on surface-nitrided Ge

We have studied ultrathin Al/sub 2/O/sub 3/ and HfO/sub 2/ gate dielectrics on Ge grown by ultrahigh vacuum-reactive atomic-beam deposition and ultraviolet ozone oxidation. Al/sub 2/O/sub 3/-Ge gate stack had a t/sub eq//spl sim/23 /spl Aring/, and three orders of magnitude lower leakage current compared to SiO/sub 2/. HfO/sub 2/-Ge allowed even greater scaling, achieving t/sub eq//spl sim/11 /spl Aring/ and six orders of magnitude lower leakage current compared to SiO/sub 2/. We have carried out a detailed study of cleaning conditions for the Ge wafer, dielectric deposition condition, and anneal conditions and their effect on the electrical properties of metal-gated dielectric-Ge capacitors. We show that surface nitridation is important in reducing hysteresis, interfacial layer formation and leakage current. However, surface nitridation also introduces positive trapped charges and/or dipoles at the interface, resulting in significant flatband voltage shifts, which are mitigated by post-deposition anneals.     

InGaAs/InP DHBTs with 120-nm collector having simultaneously high f/sub /spl tau//, f/sub max//spl ges/450 GHz

InP/In/sub 0.53/Ga/sub 0.47/As/InP double heterojunction bipolar transistors (DHBT) have been designed for increased bandwidth digital and analog circuits, and fabricated using a conventional mesa structure. These devices exhibit a maximum 450 GHz f/sub /spl tau// and 490 GHz f/sub max/, which is the highest simultaneous f/sub /spl tau// and f/sub max/ for any HBT. The devices have been scaled vertically for reduced electron collector transit time and aggressively scaled laterally to minimize the base-collector capacitance associated with thinner collectors. The dc current gain /spl beta/ is /spl ap/ 40 and V/sub BR,CEO/=3.9 V. The devices operate up to 25 mW//spl mu/m/sup 2/ dissipation (failing at J/sub e/=10 mA//spl mu/m/sup 2/, V/sub ce/=2.5 V, /spl Delta/T/sub failure/=301 K) and there is no evidence of current blocking up to J/sub e//spl ges/12 mA//spl mu/m/sup 2/ at V/sub ce/=2.0 V from the base-collector grade. The devices reported here employ a 30-nm highly doped InGaAs base, and a 120-nm collector containing an InGaAs/InAlAs superlattice grade at the base-collector junction.     

AlGaN/GaN HEMTs on SiC with f/sub T/ of over 120 GHz

AlGaN/GaN high electron mobility transistors (HEMTs) grown on semi-insulating SiC substrates with a 0.12 /spl mu/m gate length have been fabricated. These 0.12-/spl mu/m gate-length devices exhibited maximum drain current density as high as 1.23 A/mm and peak extrinsic transconductance of 314 mS/mm. The threshold voltage was -5.2 V. A unity current gain cutoff frequency (f/sub T/) of 121 GHz and maximum frequency of oscillation (f/sub max/) of 162 GHz were measured on these devices. These f/sub T/ and f/sub max/ values are the highest ever reported values for GaN-based HEMTs.     

BC high-/spl kappa//metal gate Ge/C alloy pMOSFETs fabricated directly on Si (100) substrates

Buried-channel (BC) high-/spl kappa//metal gate pMOSFETs were fabricated on Ge/sub 1-x/C/sub x/ layers for the first time. Ge/sub 1-x/C/sub x/ was grown directly on Si (100) by ultrahigh-vacuum chemical vapor deposition using methylgermane (CH/sub 3/GeH/sub 3/) and germane (GeH/sub 4/) precursors at 450/spl deg/C and 5 mtorr. High-quality films were achieved with a very low root-mean-square roughness of 3 /spl Aring/ measured by atomic force microscopy. The carbon (C) content in the Ge/sub 1-x/C/sub x/ layer was approximately 1 at.% as measured by secondary ion mass spectrometry. Ge/sub 1-x/C/sub x/ BC pMOSFETs with an effective oxide thickness of 1.9 nm and a gate length of 10 /spl mu/m exhibited high saturation drain current of 10.8 /spl mu/A//spl mu/m for a gate voltage overdrive of -1.0 V. Compared to Si control devices, the BC pMOSFETs showed 2/spl times/ enhancement in the saturation drain current and 1.6/spl times/ enhancement in the transconductance. The I/sub on//I/sub off/ ratio was greater than 5/spl times/10/sup 4/. The improved drain current represented an effective hole mobility enhancement of 1.5/spl times/ over the universal mobility curve for Si.     

A CMOS voltage reference based on weighted /spl Delta/V/sub GS/ for CMOS low-dropout linear regulators

A CMOS voltage reference, which is based on the weighted difference of the gate-source voltages of an NMOST and a PMOST operating in saturation region, is presented. The voltage reference is designed for CMOS low-dropout linear regulators and has been implemented in a standard 0.6-/spl mu/m CMOS technology (V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C). The occupied chip area is 0.055 mm/sup 2/. The minimum supply voltage is 1.4 V, and the maximum supply current is 9.7 /spl mu/A. A typical mean uncalibrated temperature coefficient of 36.9 ppm//spl deg/C is achieved, and the typical mean line regulation is /spl plusmn/0.083%/V. The power-supply rejection ratio without any filtering capacitor at 100 Hz and 10 MHz are -47 and -20 dB, respectively. Moreover, the measured noise density with a 100-nF filtering capacitor at 100 Hz is 152 nV//spl radic/(Hz) and that at 100 kHz is 1.6 nV//spl radic/(Hz).     

A novel InGaP/Al/sub x/Ga/sub 1-x/As/GaAs CEHBT

A new and interesting InGaP/Al/sub x/Ga/sub 1-x/As/GaAs composite-emitter heterojunction bipolar transistor (CEHBT) is fabricated and studied. Based on the insertion of a compositionally linear graded Al/sub x/Ga/sub 1-x/As layer, a near-continuous conduction band structure between the InGaP emitter and the GaAs base is developed. Simulation results reveal that a potential spike at the emitter/base heterointerface is completely eliminated. Experimental results show that the CEHBT exhibits good dc performances with dc current gain of 280 and greater than unity at collector current densities of J/sub C/=21kA/cm/sup 2/ and 2.70/spl times/10/sup -5/ A/cm/sup 2/, respectively. A small collector/emitter offset voltage /spl Delta/V/sub CE/ of 80 meV is also obtained. The studied CEHBT exhibits transistor action under an extremely low collector current density (2.7/spl times/10/sup -5/ A/cm/sup 2/) and useful current gains over nine decades of magnitude of collector current density. In microwave characteristics, the unity current gain cutoff frequency f/sub T/=43.2GHz and the maximum oscillation frequency f/sub max/=35.1GHz are achieved for a 3/spl times/20 /spl mu/m/sup 2/ device. Consequently, the studied device shows promise for low supply voltage and low-power circuit applications.     

Effect of tilt angle variations in a halo implant on V/sub th/ values for 0.14-/spl mu/m CMOS devices

Sensitivity of critical transistor parameters to halo implant tilt angle for 0.14-/spl mu/m CMOS devices was investigated. V/sub th/ sensitivity was found to be 3% per tilt degree. A tilt angle mismatch between two serial ion implanters used in manufacturing was detected by tracking V/sub th/ performance for 0.14-/spl mu/m production lots. Even though individual implanters may be within tool specifications for tilt angle control (/spl plusmn/0.5/spl deg/ for our specific tool type), the relative mismatch could be as large as 1/spl deg/, and therefore, result in a V/sub th/ mismatch of over 3% from nominal. The V/sub th/ mismatch results are in qualitative agreement with simulation results using SUPREM and MEDICI software.     

High-performance, metamorphic In/sub x/Ga/sub 1-x/As tunnel diodes grown by molecular beam epitaxy

Thin In/sub x/Ga/sub 1-x/As tunnel junction diodes having compositions from x=0.53 to 0.75 that span a range of bandgap energies from 0.74 to 0.55 eV, were grown on InP and metamorphic, step-graded In/sub x/Al/sub 1-x/As/InP substrates using molecular beam epitaxy and evaluated in the context of thermophotovoltaic (TPV) applications. Both carbon and beryllium were investigated as acceptor dopants. Metamorphic tunnel diodes with a bandgap of 0.60 eV (x=0.69) using carbon acceptor doping displayed highest peak current densities, in excess of 5900 A/cm/sup 2/ at a peak voltage of 0.31 V, within a 200 /spl Aring/ total thickness tunnel junction. Identically doped lattice-matched tunnel diodes with a bandgap of 0.74 eV exhibited lower peak current densities of approximately 2200 A/cm/sup 2/ at a higher peak voltage of 0.36 V, consistent with the theoretical bandgap dependence expected for ideal tunnel diodes. Specific resistivities of the 0.60 eV bandgap devices were in the mid-10/sup -5/ /spl Omega/-cm/sup 2/ range. Together with their 200 /spl Aring/ total thickness, the electrical results make these tunnel junctions promising for TPV applications where low-resistance, thin metamorphic tunnel junctions are desired.     

Stress-related hydrogen degradation of 0.1-/spl mu/m InP HEMTs and GaAs PHEMTs

Hydrogen degradation of III-V field-effect transistors (FETs) is a serious reliability concern. Previous work has shown that threshold-voltage shifts induced by H/sub 2/ exposure in 1-/spl mu/m-channel InP high-electron mobility transitors (HEMTs) can be attributed to compressive stress in the gate due to the formation of TiH/sub x/ in Ti/Pt/Au gates. The compressive stress affects the device characteristics through the piezoelectric effect. This paper examined the H/sub 2/ sensitivity of 0.1-/spl mu/m strained-channel InP HEMTs and GaAs pseudomorphic HEMTs. After exposure to H/sub 2/, the threshold voltage V/sub T/ of both types of devices shifted positive. This positive shift in V/sub T/ is predicted by a model for hydrogen-induced piezoelectric effect. In situ V/sub T/ measurements reveal distinct time dependences of the V/sub T/ shifts, which are also consistent with stress-related phenomena.     

Dual high-/spl kappa/ gate dielectric with poly gate electrode: HfSiON on nMOS and Al/sub 2/O/sub 3/ capping layer on pMOS

In this letter, a novel dual high-/spl kappa/ approach, different high-/spl kappa/ dielectrics in nMOS and pMOS, with poly Si gate electrode is introduced. By turning the Fermi-pinning effect into an advantage, this dual high-/spl kappa/ approach achieved a lower V/sub tp/ and a symmetrical V/sub tn//V/sub tp/ over a wide range of channel lengths for potential high-/spl kappa//poly Si CMOS application. In addition to the V/sub t/ control, this approach also can improve the drive current ratio between nMOS and pMOS, which would further scale the CMOS area by reducing the pMOS width.