Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Water-soluble copolymers. I. Synthesis of model dextran-g-polyacrylamides by Fe(II)/H2O2 initiation and characterization by aqueous size exclusion chromatography

Model graft copolymers were synthesized by grafting acrylamide onto dextran (M?_w = 500,000) utilizing the Fe(II)/H₂O₂ initiation system. Aqueous size exclusion chromatography (SEC) was used to determine the effects of changing reaction parameters on hydrodynamic dimensions of the resulting graft copolymers. It was also possible to optimize reaction conditions yielding the highest viscosity graft copolymer with the least amount of homopolyacrylamide and unreacted substrate. The molecular structures of the graft copolymers were determined by elemental analysis, SEC, and solution viscometry. Selective hydrolysis of the dextran backbone allowed determination of average molecular weight of acrylamide grafts, number of grafting sites, and average molecular weight of the graft copolymers. Rheological studies indicated viscosity and pseudoplastic behavior were largely related to the graft length of the polyacrylamide side chains.     

Molecular weight distribution of commercial PVC

The molecular weight distribution (MWD) of commercial suspension grade poly(vinyl chloride) (PVC) resins with K values from 50 to 93 and mass grade PVC resins with K values from 58 to 68 has been determined by size exclusion chromatography (SEC), using literature Mark‐Houwink coefficients. The MWD is characterized by the number average molecular weight (M_n), the weight average molecular weight (M_w) and the polydispersity (M_w/M_n). Our results for M_w are consistent with recently published data, but we find different results for M_n and consequently for M_w/M_n. The polydispersity of PVC increases with increasing K value. This effect can be explained by two mechanisms. The first mechanism is a reduced terminating reaction rate between two growing polymer chains (disproportionation) at higher molecular weight owing to the reduced mobility of the polymer chains. The second mechanism is long‐chain branching of molecules with high molecular weight which lets the molecules grow at two ends. For two examples graphs of the measured MWD are compared with the theoretically expected MWD.     

Calibration of size-exclusion chromatography columns with polydisperse polymer standards. II. Applications

New methods for calibrating SEC columns by means of polydisperse polymer samples with known M_n and M_w have been tested with computer-generated chromatograms and with experimental data of high-performance SEC. Calculations with the artificial chromatograms show that accurate calibration dependences can be recovered even when polymers with broad and/or bimodal molecular weight distributions are used as standards. Polystyrene calibration calculated by the proposed method from chromatograms of five polydisperse polystyrenes follows closely the curve obtained in a conventional manner from nine narrow polystyrene standards. The dependence log M vs. ν for PMMA determined from chromatograms of six PMMA samples with moderately broad molecular weight distributions agrees well with the curve obtained by shifting the dependence for polystyrene using the universal calibration concept. The new method is particularly useful when SEC columns are to be calibrated for dextrans in water, where only a few standards having a rather broad molecular weight distribution are available, and can considerably improve the accuracy of molecular weight determination by SEC.     

Improved accuracy and precision in the light-scattering characterization of homo- and copolymers in THF

A one-point method was developed for the estimation of weight-averaged molecular weights from light-scattering data. The method is based on the calculation of the second virial coefficient from theoretical predictions of the dependence of A₂ on the molecular weight. The second virial coefficient is then regressed for a particular polymer—solvent combination from a series of preexisting measurements over a range of molecular weights. The one-point method is found to yield as accurate molecular weight estimates as obtained from a Debye plot using the conventional dilution technique. The variance in the estimation of the Rayleigh factor has also been found to be highly dependent on the measurement concentration. Therefore, the precision in the estimation of molecular weight can be improved by calculating molecular weights at or near the optimal concentration, which is itself molecular weight-dependent. The one-point method is demonstrated for poly(methyl methacrylate)s of various polydispersities in tetrahydrofuran. The molecular weight of polystyrene and polystyrene-co-acrylic acid were also estimated by the one-point method in THF. In the case of the polystyrene-co-acrylic acid, THF becomes a poorer solvent with increasing levels of acrylic acid in the copolymer, and the parameter (A₂M^0.5) is found to vary with the copolymer composition, as is theoretically predicted. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 66: 1303–1316, 1997     

Synthesis and characterization of amphiphilic graft copolymer poly(ethylene oxide)-graft-poly(methyl acrylate)

A novel well-defined amphiphilic graft copolymer of poly(ethylene oxide) as main chain and poly(methyl acrylate) as graft chains is successfully prepared by combination of anionic copolymerization with atom transfer radical polymerization (ATRP). The glycidol is protected by ethyl vinyl ether first, then obtained 2,3-epoxypropyl-1-ethoxyethyl ether (EPEE) is copolymerized with EO by initiation of mixture of diphenylmethyl potassium and triethylene glycol to give the well-defined poly(EO-co-EPEE), the latter is deprotected in the acidic conditions, then the recovered copolymer [(poly(EO-co-Gly)] with multi-pending hydroxyls is esterified with 2-bromoisobutyryl bromide to produce the ATRP macroinitiator with multi-pending activated bromides [poly(EO-co-Gly)_(ATRP)] to initiate the polymerization of methyl acrylate (MA). The object products and intermediates are characterized by NMR, MALDI-TOF-MS, FT-IR, and SEC in detail. In solution polymerization, the molecular weight distribution of the graft copolymers is rather narrow (M_w/M_n < 1.2), and the linear dependence of Ln [M₀]/[M] on time demonstrates that the MA polymerization is well controlled.     

Low-angle laser light scattering–aqueous size exclusion chromatography of polysaccharides: Molecular weight distribution and polymer branching determination

A low-angle laser light scattering detector (LALLS) used with size exclusion chromatography (SEC/LALLS) has been applied for the determination of molecular weight, molecular weight distribution (MWD), and degree of branching of polysaccharides in 0.5N NaOH aqueous solution. Data from both detectors [differential refractive index (DRI) and LALLS] are used to calculate the absolute molecular weight at each point in a sample chromatogram. The correct average molecular weight and MWD can be obtained without calibration methods used in conventional SEC. As a consequence of this technique, Mark—Houwink coefficients can be predicted from a single broad-distribution, homopolymer without recourse to time-consuming fractionation methods. Moreover, the hydrodynamic volume separation mechanism of SEC can be exploited with the SEC/LALLS method to gain information about polymer branching. In the studies described in this paper, SEC/LALLS has been employed to obtain data about the branching parameters g_v and g_M for samples of amylose, amylopectin, starch, and glycogen. For three homopolymers (amylose, amylopectin, and glycogen), branching frequency (as measured by chemical means), and the branching parameters (g_v and g_M) are inversely related. This trend is consistent with theoretical predictions. For starch, a nonhomogeneous branching distribution is observed as a function of molecular weight.     

High molecular weight hydrophilic functional copolymers by free‐radical copolymerization of acrylamide and of N‐acryloylmorpholine with N‐acryloxysuccinimide: Application to the synthesis of a graft copolymer

Free‐radical solution copolymerization of acrylamide (AAm) and of a disubstituted acrylamide derivative, N‐acryloylmorpholine (NAM), with N‐acryloxysuccinimide (NAS) was investigated with the aim to obtain a copolymer of at least 100,000 g mol^?1. Different polymerization conditions likely to increase the molecular weight were studied such as monomer and initiator concentrations, temperature, and nature of the solvent. The molecular weights were determined by SEC using a light‐scattering detector. The grafting of end‐functionalized polysaccharide chains onto such high molecular weight poly(NAM‐co‐NAS) was performed and a graft copolymer bearing a high number of saccharidic branches was obtained. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1808–1816, 2003     

Synthesis and characterization of poly(ε-caprolactone)-containing amino acid-based poly(ether ester amide)s

A new family of biodegradable amino acid-based poly(ether ester amide)s (AA-PEEAs) consisting of three building blocks [poly(ε-caprolactone) (PCL), L -phenylalanine (Phe), and aliphatic acid dichloride] were synthesized by a solution polycondensation. Using DMA as the solvent, these PCL-containing Phe-PEEA polymers were obtained with fair to very good yields with weight average molecular weight (M_w) ranging from 6.9 kg/mol to 31.0 kg/mol, depending on the original molecular weight of PCL. The chemical structures of the PCL-containing Phe-PEEA polymers were confirmed by IR and NMR spectra. These PCL-containing Phe-PEEAs had lower T_g than most of the oligoethylene glycol (OEG) based AA-PEEAs due to the more molecular flexibility of the PCL block in the backbones, but had higher T_g than non-amino acid based PEEA. The solubility of the PCL-containing Phe-PEEA polymers in a wide range of common organic solvents, such as THF and chloroform, was significantly improved when comparing with aliphatic diol based poly(ester amide)s and OEG based AA-PEEAs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis of monodisperse poly(butyl acrylate) initiated by SmMe(C5Me5)2(THF) and its adhesive properties after crosslinking by electron‐beam irradiation

Polymerization reactions of butyl acrylate (BuA) were carried out using an organosamarium complex, SmMe(C₅Me₅)₂(THF), as an initiator. Polymerization proceeds quantitatively to give high number‐average molecular mass polymers (M_n > 200,000) and narrow molecular weight distributions (M_w/M_n < 1.07). Irradiation of the resulting poly(BuA) with an electron beam (EB) gave crosslinked poly(BuA). Improved viscoelastic and adhesive properties of these polymers were useful for high‐temperature applications. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 432–437, 2001     

Synthesis and characterization of poly(1-methyl-1-silabutane), poly(1-phenyl-1-silabutane) and poly(1-silabutane)

Summary Anionic ring opening polymerization of 1-methyl-1-silacyclobutane, 1-phenyl-1-silacyclobutane and 1-silacyclobutane co-catalyzed by n-butyllithium and hexamethylphosphoramide (HMPA) in THF at-78°C yields poly(1-methyl-1-silabutane), poly(1-phenyl-1-silabutane) and poly(1-silabutane) respectively. These saturated carbosilane polymers possess reactive Si-H bonds. They have been characterized by ¹H, ¹³C and ²⁹Si NMR as well as FT-IR and UV spectroscopy. Their molecular weight distributions have been determined by gel permeation chromatography (GPC), thermal stabilities by thermogravimetric analysis (TGA) and glass transition temperatures (T_g) by differential scanning calorimetry (DSC).     

Translational Diffusion Coefficient of Sodium Poly(2-acrylamido-2-methylpropanesulfonate) in Aqueous Sodium Chloride

Summary Dynamic light scattering measurements have been made on 9 samples of sodium poly(2-acrylamido-2-methylpropanesulfonate), an intrinsically flexible, linear poly-electrolyte, ranging in weight-average molecular weight from 2.9×10⁴ to 1.5×10⁶ with 0.05 and 0.5 M aqueous NaCl at 25 °C as the solvents. The measured translational diffusion coefficients or hydrodynamic radii R_H are analyzed on the basis of the wormlike chain with excluded volume. The quasi-two-parameter theory for the hydrodynamic-radius expansion factor with the known expression for the translational friction coefficient of an unperturbed wormlike chain describes the molecular weight dependence of R_H in the aqueous salts with a degree of accuracy very similar to that known for nonionic flexible polymers in good solvents.     

Synthesis and characterization of well-defined hydrophilic block copolymer brushes by aqueous ATRP

Homopolymer brushes of poly(N,N-dimethylacrylamide) (PDMA), poly(methoxyethylacrylamide) (PMEA) and poly(N-isopropylacrylamide)(PNIPAM) grown on atom transfer radical polymerization (ATRP) initiator functionalized latex particles were used as macroinitiators for the synthesis of PDMA-b-PNIPAM/PMEA, PMEA-b-PDMA/PNIPAM and PNIPAM-b-PDMA block copolymer brushes by surface initiated aqueous ATRP. The grafted homopolymer and block copolymer brushes were analyzed for molecular weight, molecular weight distribution, chain grafting density, composition and hydrodynamic thickness (HT) using gel permeation chromatography-multi-angle laser light scattering, ¹H NMR, particle size analysis and atomic force microscopy (AFM) techniques. The measured graft molecular weight increased following the second ATRP reaction in all cases, indicating the second block had been added. Chain growth depended on the nature of the monomer used for block copolymerization and its concentration. Unimodal distribution of polymer chains in GPC with non-overlap of molar mass-elution volume curves implied an efficient block copolymerization. This was supported by the increase in HT measured by particle size analysis, equilibrium thickness observed by AFM and the composition of the block copolymer layer by ¹H NMR analysis, both in situ and on cleaved chains in solution. ¹H NMR analysis of the grafted latex and cleaved polymers from the surface demonstrated that accurate determination of the copolymer composition by this method is possible without detaching polymer chains from surface. Block copolymer brushes obey the same power law dependence of HT on molecular weight as homopolymer brushes in good solvent conditions. The NIPAM-containing block copolymer brushes were sensitive to changes in the environment as shown by a decrease in HT with increase in the temperature of the medium.     

Light-scattering and size-exclusion chromatographic characterization of hydroxyethyl cellulose acetate

A recently developed analytical method of combining off-line laser light scattering (LLS) and size exclusion chromatography (SEC) was used to investigate a set of moderately distributed hydroxyethyl cellulose acetate (HECA) samples in tetrahydrofuran (THF) at room temperature. Our results have shown that this new LLS + SEC method is suitable for the characterization of molecular weight distribution of HECA. By using this method, we have simultaneously determined two calibrations of V (cm³) = 45.3 ? 1.89 log (M) and D (cm²/s) = 2.45 × 10^?4 M^?0.60, where M is the molecular weight of HECA; V, the elution volume in SEC; and D, the translational diffusion coefficient in dynamic LLS. In addition, our results have also indicated that the chain conformation of HECA in THF at room temperature is a slightly extended linear coil. © 1995 John Wiley & Sons, Inc.     

Characterization of a nylon 6/poly(methyl acrylate) copolymer produced by radiation grafting

Acrylic acid has been grafted onto nylon 6 by the mutual γ-irradiation technique. Methods are described for removing poly(acrylic acid) homopolymer and ungrfted nylon, the latter involving intermediate conversion to the calcium ionomer. The pure graft copolymer in its methylated form, viz., nylon 6/poly(methyl acrylate), NY/PMA, was characterized by light scattering in mixed solvents to yield the true molecular weight (3.2 × 10⁶) as well as the molecular weights M_PMA(domain) and M_NY(domain) of the PMA and NY portions, respectively. The molecular weight M_PMA of the grafts was measured after hydrolysis of the backbone, and the molecular weight M_NY of the backbone was determined via a previously devised indirect procedure. Comparisons of M_PMA(domain) with M_PMA and of M_NY(domain) with M_NY gave ? 7 nylon chains and ? 17 poly(methyl acrylate) chains per copolymer molecule. Chain transfer and bimolecular terminatin during grafting are proposed as probable contributory factors to the branched structure of the copolymer.     

Determination of the absolute molecular weight of a styrene–butyl acrylate emulsion copolymer by low-angle laser light scattering (LALLS) and GPC/LALLS

The application of low-angle laser light scattering (LALLS) and combined GPC/LALLS for the measurement of absolute molecular weight distribution of a styrene–butylacrylate (30/70) emulsion copolymer is discussed. From the static light scattering measurements in four different solvents, i.e., toluene, tetrahydrofuran (THF), methyl ethyl ketone (MEK), and dimethylformamide (DMF), the true weight average molecular weight (M _w) and heterogeneity parameters are determined. The apparent M _w obtained from the static measurement in THF was in good agreement with the M _w determined from the multiple solvent analysis, suggesting the validity of using THF as the mobile phase in the combined GPC/LALLS analysis.     

Light scattering of acetylated lignin

Organosolv lignin was fractionated on a Sephadex G 75 column with 0.1M aqueous NaOH resulting in 14 fractions. These fractions were acetylated and a high-molecular-weight fraction (F3) was investigated by means of combined static and dynamic light scattering (LS) in solvents acetone, tetrahydrofuran (THF), and trifluoroethanol (TFE). The measurements were found to be reproducible, and recycling of lignin by freeze drying caused slight but unessential changes in solution properties. Depending on the solvent used, weight average molecular weights M_w between two and ten million were found. By contrast, M_n of the fractions, measured by vapor pressure osmometry (VPO), was in the range of a few thousands only. Analysis of the angular dependence in static LS by means of a Casassa–Holtzer plot and the fractal dimensions showed the presence of chain stiffness, most distinct in TFE. Also, the dynamic light scattering results in TFE are typical for semiflexible chains, while in THF, and to some extent in acetone, the dynamic measurements including viscosity suggest the presence of spherical structures. These findings are being explained by large lignin clusters that consist of stiff subunits.     

Number‐average molecular weight of branched polymers from SEC with viscosity detection and universal calibration

BACKGROUND: Number‐average molecular weight, M?_n, is an important characteristic of synthetic polymers. One of the very few promising methods for its determination is size‐exclusion chromatography (SEC) using on‐line viscometric detection and assuming the validity of the universal calibration concept. RESULTS: We have examined the applicability of this approach to the characterization of statistically branched polymers using 22 copolymers of styrene and divinylbenzene as well as 3 homopolymers of divinylbenzene with various degrees of branching. SEC with three on‐line detectors, i.e. concentration, light scattering and viscosity, enables us to evaluate experimental data by various computational procedures yielding M?_n and weight‐average molecular weight, M?_w. Analysis of the results has shown that the universal calibration theorem has limited validity, apparently due to the dependence of the Flory viscosity function on the molecular shape, the molecular weight distribution and the expansion of molecules. CONCLUSION: For complex polymers, the universal calibration, i.e. the dependence of the product of intrinsic viscosity and molecular weight, [η]M, on elution volume, can differ in values of [η]M from those obtained for narrow molecular weight standards by 10–15%. The method studied is helpful for the determination of M?_n of polymers, in particular of those with very broad molecular weight distribution, such as statistically highly branched polymers. Copyright © 2008 Society of Chemical Industry     

Characterization of the network structure of hydroxyl terminated poly(butadiene) elastomers prepared by different reactive systems

Three types of hydroxyl terminated poly(butadiene) (HTPB) networks having different NCO/OH reactive group ratios were prepared using three different reactive systems (i.e., Desmodur N-100 pluriisocyanate, isophorone diisocyanate (IPDI)/trimethylol propane (TMP), and hexamethylene diisocyanate (HMDI)/TMP). Desmodur N-100 and TMP were used as polyfunctional reactants. The polymer–solvent interaction parameters (χ₁) for HTPB–tetrahydrofuran (THF) and HTPB–chloroform systems at 45°C were determined, using a vapor pressure osmometer (VPO), as 0.31 and 0.24, respectively. Equilibrium swelling values of the networks in THF and chloroform and the data obtained by osmometry were further used for the calculation of the mean number-average molecular weight between junction points (M _c) of HTPB networks through the Flory-Rehner equation. The M _c values of each network, which were calculated from the swelling data obtained in THF and chloroform using the corresponding χ₁ parameters for polymer–solvent systems, were found to be nearly the same. The changes in the mechanical, swelling, and the solubility properties of the networks prepared by three different reactive systems were followed. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 1129–1135, 1998     

Thermal analysis of poly(phenylene sulfide) polymers. I: Thermal characterization of PPS polymers of different molecular weights

Thermal properties of Fortron®

1 ®Registered trademark of Hoechst Celanese Corporation.

poly(phenylene sulfide) (PPS) polymers of different molecular weights were studied by DSC. Crystallization studies revealed that the ability of these polymers to crystallize decreases with increasing molecular weight. The Avrami equation poorly describes the isothermal crystallization of PPS. Lamellar crystallization was observed for the lowest molecular weight sample. For the other, higher molecular weight polymers the Avrami exponent is always between 2 and 3, suggesting development of distorted spherulites with heterogeneous nucleation. The temperature dependence of the solid and melt heat capacities have been determined. The solid specific heat capacity did not exhibit a molecular weight dependence. The heat capacity increase at the glass transition, T_g, has been calculated to be 28.1 J°C^?1 mole^?1. The equilibrium melting point of PPS has been estimated to be 348.5°C using the Hoffman–Weeks method. The T_g of PPS increases with molecular weight. The T_g of the highest molecular weight evaluated is 92.5°C. A DMA relaxation peak corresponding to the onset of the phenylene ring rotation occurs at ?92°C. Only the highest molecular weight could be quenched to a completely amorphous state.