Fluconazole release through semi‐interpenetrating polymer network hydrogels based on chitosan,acrylic acid,and citraconic acid

Semi‐interpenetrating polymer network hydrogels with different compositions of chitosan (Cs), acrylic acid, and citraconic acid were synthesized via free‐radical polymerization with ethylene glycol dimethacrylate as a crosslinker. The variations of the swelling percentages of the hydrogels with time, temperature, and pH were determined, and Cs–poly(acrylic acid) (PAA) hydrogels were found to be most swollen at pH 7.4 and 37°C. Scanning electron micrographs of Cs–PAA and Cs–P(AA‐co‐CA)‐1 (Cs‐poly(acrylicacid‐co‐citraconir acid)^?1) were taken to observe the morphological differences in the hydrogels. Although the less swollen hydrogel, Cs–P(AA‐co‐CA)‐1, had a sponge‐type structure, the most swollen hydrogel, Cs–PAA, displayed a uniform porous appearance. Fluconazole was entrapped in Cs–P(AA‐co‐CA)‐1 and Cs–PAA hydrogels, and the release was investigated at pH 4.0 and 37°C. The kinetic release parameters of the hydrogels (the gel characteristic constant and the swelling exponent) were calculated, and non‐Fickian diffusion was established for Cs–PAA, which released fluconazole much more slowly than the Cs–P(AA‐co‐CA)‐1 hydrogel. A therapeutic range was reached at close to 1 h for both hydrogels. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

PH-induced structure change of poly(vinyl alcohol) hydrogel crosslinked with poly(acrylic acid)

The structure of the hydrogel of poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) was investigated by small angle X-ray scattering (SAXS) of synchrotron radiation. A physically crosslinked blend gel, which was prepared by repetitive freezing and thawing of an aqueous solution of PVA and PAA, could be chemically crosslinked by esterfication of PVA with PAA even in the hydrogel state. The chemical crosslinking induced the destruction of physical crosslinks into a folded structure, indicating that the chemical crosslinking proceeds at the sites around the physical crosslinks that contain PVA and PAA in much higher concentration than other portion of the gel. The pH-induced structure changes of the PVA hydrogels, chemically crosslinked with poly(acrylic acid) (PAA) were investigated by SAXS on the samples of various chemical crosslinking time. The gels were shrunk at pH4, and swollen at pH8. The results of SAXS showed, that the Porod slope changed with chemical crosslinking time from -3.5 to ?2.9 at pH4, and from ?2.9 to ?2.4 at pH8. The results suggest that a folded structure as a structural domain, which is characterized by fractally rough interface, tends to change into the structure that corresponds to percolation cluster, particularly at pH8. The gels immersed in pH8 showed a remarkable structure change accompanying swelling. The results revealed that a conformational change of PAA chains, induced by the pH change, can be explained by the presence of a structural domain in the gel network, where both PVA chains and PAA chains get entangled and partially form a interpenetrating polymer network(IPN).     

Hollow poly(N‐isopropylacrylamide)‐co‐poly(acrylic acid) microgels with high loading capacity for drugs

A convenient approach has been developed for the preparation of microsize hydrogels composed of crosslinked poly(acrylic acid) (PAA) and poly(N‐isopropylacrylamide) (PNIPAm). First, semi‐interpenetration polymer networks of hydropropylcellulose (HPC) and PNIPAm‐co‐PAA copolymer are formed through the copolymerization and crosslinking of monomer acrylic acid and N‐isopropylacrylamide in HPC aqueous solution. After the selective removal of HPC from networks due to ionization of PAA units and disruption of hydrogen bonding with increasing pH, PNIPAm‐co‐PAA microgels are obtained, whose volume is confirmed to be responsive to both temperature and pH. Doxorubicin hydrochloride (Dox) can be encapsulated in PNIPAm‐co‐PAA microgels with high drug loading driven by the electrostatic interaction, and a sustained‐release characteristic of Dox from the microgels is observed under physiological pH value and temperature. In vitro cell experiments, the drug‐loaded microgels can be taken up by LoVo cells and release their payload in cell cytoplasm without loss of drug efficacy. This indicates that PNIPAm‐co‐PAA microgels might be a potential drug delivery carriers especially for water‐soluble or polypeptide drugs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and properties of chitosan‐modified poly(acrylic acid)

Potassium persulfate (K₂S₂O₈) was used to initiate the polymerization of acrylic acid (AA) monomer in a chitosan (CS) solution. Both a poly(acrylic acid) (PAA) homopolymer and a CS‐co‐PAA copolymer were produced. When the amount of AA was increased from 5 to 40 g with 5 g of CS, the total monomer conversion was found to increase from 89 to 98% after 2 h of reaction at 70°C. In addition, the percentage of reacted AA monomer being converted to the CS‐co‐PAA copolymer (copolymerization efficiency) and the weight composition of the PAA portion in the copolymer (copolymer composition) both increased with the amount of AA added. The structures and properties of the synthesized CS‐modified PAA polymers were studied. In Fourier transform infrared spectra, the formation of a polyelectrolyte complex between CS chains and PAA chains could be observed. From the thermograms obtained via differential scanning calorimetry, we found that the presence of rigid CS chains increased the glass‐transition temperature of PAA. Thermogravimetric analysis revealed three stages of degradation of the synthesized CS‐modified PAA polymers. The swelling ratio of the CS‐modified PAA polymers depended on the pH value and had a maximum value in a buffer solution at pH 7. This was due to the changes in the morphological structure with the pH value. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Determination of swelling behavior and morphological properties of poly(acrylamide‐co‐itaconic acid) and poly(acrylic acid‐co‐itaconic acid) copolymeric hydrogels

Poly(acrylamide‐co‐itaconic acid) (PAAmIA) and poly(acrylic acid‐co‐itaconic acid) (PAAIA) copolymeric hydrogels were prepared with different compositions via free‐radical polymerization. Ethylene glycol dimethacrylate (EGDMA) was used as an original crosslinker for these monomers. Gelation percentages of the monomers were studied in detail and it was found that addition of IA into the monomer mixture decreased the gelation percentage. The variation in swelling values (%) with time, temperature, and pH was determined for all hydrogels. PAA, which is the most swollen hydrogel, has the swelling percentage value of 2000% at pH = 7.4, 37°C. Swelling behaviors were explained with detailed SEM micrographs, which show the morphologic differences between dry and swollen hydrogels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5994–5999, 2006     

Synthesis and superswelling behavior of carboxymethylcellulose–poly(sodium acrylate‐co‐acrylamide) hydrogel

In this paper, attention is paid to synthesis and swelling behavior of a superabsorbent hydrogel based carboxymethylcellulose (CMC) and polyacrylonitrile (PAN). The physical mixture of CMC and PAN was hydrolyzed in NaOH solution to yield hydrogel, CMC–poly(NaAA‐co‐AAm). During alkaline hydrolysis, the nitrile groups of PAN were completely converted to a mixture of hydrophilic carboxamide and carboxylate groups followed by in situ crosslinking of the grafted PAN chains. A proposed mechanism for hydrogel formation was suggested and the structure of the product was established using FTIR spectroscopy. The reaction variables affecting the swelling capacity of the hydrogel were systematically optimized to achieve a hydrogel with swelling capacity as high as possible. Swelling measurements of the synthesized hydrogels in various chloride salt solutions indicated a swelling‐loss with increase in the ionic strength of the salt solutions. The pH of the various solutions also affected the swelling of the superabsorbent. Furthermore, the present hydrogels showed a pH‐reversible property. Finally, the swelling kinetics of synthesized hydrogels with various absorbent particle sizes was briefly examined. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(methacrylamide‐co‐acrylic acid) hydrogels for gastrointestinal delivery of theophylline. I. Swelling characterization

pH sensitive copolymeric hydrogels have been synthesized by free‐radical polymerization of methacrylamide and acrylic acid in aqueous medium. The gels were characterized by FTIR spectroscopy, thermogravimetric analysis, and swelling measurements. To determine the suitability of theses hydrogels for gastrointestinal oral delivery of model drug theophylline, their swelling behavior was investigated as a function of pH and various structural parameters such as the average molecular weight between crosslinks, crosslink density, and mesh size were calculated. Likewise initial, average and late time diffusion coefficients were also evaluated in simulating intestinal fluid of pH 6.8 at 37°C. The gel underwent sharp volume phase transition in the vicinity of pH 5.8. The mesh sizes of the hydrogel were between 8.4 and 9.2 Å in the collapsed state (pH range 1–2; SGF) and between 514 and 524 Å in the swollen state (pH range 7–8; SIF). The experimental data was found to fit well to Beren‐Hopfenberg equation thus suggesting that later part of swelling was chain relaxation controlled. The activation energy, as determined from Arrhenius equation was found to be 13.71 kJ mol^?1. Likewise, enthalpy of mixing was also evaluated using Gibbs‐Helmholtz equation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 2995–3008, 2006     

Electrical actuation of electroresponsive hydrogels based on poly(acrylamide‐co‐acrylic acid)/graphite suitable for biomedical applications

A pH‐sensitive composite hydrogel based on poly(acrylamide‐co‐acrylic acid)/graphite was prepared by solution polymerization process in presence of redox initiator potassium persulfate/N,N,N′,N′‐tetramethylethylenediamine and cross‐linker (ethylene glycol dimethylacrylate). The structures of the hydrogels were confirmed using Fourier transform infrared, X‐ray diffraction, and scanning electron microscopy (SEM) study. Tensile strengths of the hydrogels were determined by using a universal tensile machine, whereas the electrical conductivities of the hydrogels were evaluated using Four‐probe method. The influence of cross‐linker, graphite content, and temperature on the conductivity of the hydrogel was also investigated. The bending behavior of the conducting hydrogels was investigated by exposing the hydrogels under electric field in aqueous medium. By studying the swelling ratio of the polymer synthesized under different conditions, optimization conditions were found for a polymer with the highest swelling ratio. Also, the hemolytic potentiality test revealed that prepared hydrogels are biocompatible in nature. POLYM. COMPOS., 35:27–36, 2014. © 2013 Society of Plastics Engineers     

Effect of the anionic‐group/cationic‐group ratio on the swelling behavior and controlled release of agrochemicals of the amphoteric,superabsorbent polymer poly(acrylic acid‐co‐diallyldimethylammonium chloride)

A series of amphoteric, superabsorbent polymers [poly(acrylic acid‐co‐diallyldimethylammonium chloride)] with different molar ratios of anionic groups to cationic groups were prepared by solution polymerization to investigate their swelling behaviors and the controlled release of agrochemicals. Various factors, including the solution pH, the concentrations of different salt solutions, and the temperature, were studied. The dynamic parameters of hydrogels at different temperatures suggested that diffusion was Fickian at lower temperatures, whereas non‐Fickian diffusion prevailed at higher temperatures. A copolymer hydrogel with a low anionic‐group/cationic‐group ratio showed a higher swelling capacity in water and higher salt tolerance. Also, the anionic‐group/cationic‐group ratio was not the dominant factor in determining the water retention. A poly(acrylic acid‐co‐diallyldimethylammonium chloride) hydrogel could control the release of agrochemicals effectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 986–991, 2006     

Microwave electromagnetic properties of polyimide/carbonyl iron composites

A facile and effective approach was developed to fabricate dual temperature- and pH-sensitive hollow nanospheres utilizing an atom transfer radical polymerization (ATRP) method. To do this silica nanoparticles were used as primary cores that could be etched by an hydrofluoric (HF) aqueous solution. Due to uncontrolled ATRP of acrylic acid (AA) methyl acrylate (MA) was polymerized via surface-initiated ATRP (SI-ATRP) a and poly(2-hydroxyethyl methacrylate) (PHEMA) block was added via the same approach. To synthesize poly(AA-co-HEMA)-grafted silica nanoparticles polymethyl acrylate (PMA) chains were hydrolyzed to polyacrylic acid (PAA) using an aqueous NaOH solution. PAA segments were partially crosslinked via an esterification reaction of –COOH groups with 1,4-butanediol. Finally, poly(AA-co-HEMA) hollow nanospheres were fabricated by etching silica cores with an HF aqueous solution. The structure of the nanospheres was revealed by transmission electron microscopy (TEM). These hollow nanospheres consisting of poly(AA-co-HEMA) in their structure showed dual pH- and thermo-sensitive properties as measured by dynamic light scattering (DLS). The hydrodynamic diameter was measured as an affected parameter under different pH (3–12) and temperature (25–55 °C) conditions. Results showed that by decreasing pH or by increasing temperature the hydrodynamic diameter decreased and a lower critical solution temperature (LCST) point was observed.     

Hydroxyethyl chitosan‐g‐poly(acrylic acid‐co‐sodium acrylate) superabsorbent polymers

A novel hydroxyethyl chitosan‐g‐poly(acrylic acid‐co‐Sodium Acrylate) (HECTS‐g‐(PAA‐co‐PSA)) superabsorbent polymer was prepared through graft copolymerization of acrylic acid and sodium acrylate onto the chain of hydroxyethyl chitosan. The structure of the polymer was characterized by FTIR. By studying the water absorption of the polymer synthesized under different conditions, the optimal conditions for synthesizing the polymer with the highest swelling ratio was defined. This superabsorbent polymer was further treated by the solvent precipitation method and by the freeze‐drying method. We found that the water absorption rate of the treated polymer was greatly increased and the microstructure of the treated polymer was changed from small pores to loose macro pores. The swelling processes of the polymers before and after modification fit first‐order dynamic processes. The amount of the residual acrylic acid was greatly decreased after treatments. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Hydrogels composite of poly(acrylamide‐co‐acrylate) and rice husk ash. I. Synthesis and characterization

Composite hydrogels of poly(acrylamide‐co‐acrylate) with rice husk ash (RHA) were synthesized and studies of the swelling variables were accomplished comparatively with commercial polyacrylamide gel and PAMACRYL, a poly(acrylamide‐co‐acrylate) hydrogel without RHA. FT‐IR and WAXS were the techniques employed for characterizing a series of hydrogel obtained by varying the percentage of RHA (1, 2, 5, 10, and 20 wt %) and the amount of crosslinking agent (0.05, 0.1, and 0.2 mol %) relative to sum of AAm and AAc. Superabsorbent hydrogel with W_eq > 800 g H₂O/g gel was obtained with percentage of 10 wt % of RHA and 0.1 of crosslinking agent mol %. The hydrogel showed to be sensitive to the pH variation and to the presence of salts. The hydrogels, even though submitted through cycles of drying and swelling, preserved their superabsorbent characteristics and demonstrated better water absorbance properties when compared with commercial polyacrylamide gel. The composite hydrogels of poly(acrylamide‐co‐acrylate) with RHA presented good characteristics to be applied as soil conditioner for using in agriculture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The swelling behaviors and network parameters of cationic starch‐g‐acrylic acid/poly(dimethyldiallylammonium chloride) semi‐interpenetrating polymer networks hydrogels

Amphiphilic semi‐interpenetrating polymer networks (semi‐IPN) hydrogels were prepared by a sequential‐IPN method by acrylic acid graft copolymerization into cationic starch in mild aqueous media of poly(dimethyldiallylammonium chloride). Some main factors were investigated to evaluate the swelling of hydrogels, and the network parameters M_c were given accordingly to elaborate the interaction between polymers. The chemical structure of the resulting hydrogel was confirmed using Fourier transform infrared spectroscopy. The cationic starch‐based semi‐IPN hydrogels achieved a high swelling capacity of 1070 g/g in deionized water and 94 g/g in 0.9 wt % NaCl solution, respectively) and high compressive stress in a high water content. Besides, a different pH‐dependent behavior was found for this semi‐IPN hydrogel. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of polyacrylic acid‐poly(vinyl alcohol)‐based interpenetrating hydrogels

Some structural features of hydrogels from poly(acrylic acid) (PAAc) of various crosslinking degrees have been investigated through mechanical and swelling measurements. Interpenetrating polymer hydrogels (IPHs) of poly(vinyl alcohol) (PVA) and PAAc have been prepared by a sequential method: crosslinked PAAc chains were formed in aqueous solution by crosslinking copolymerization of acrylic acid and N,N‐methylenebisacrylamide in the presence of PVA. The application of freeze–thaw (F–T) cycles leads to the formation of a PVA hydrogel within the synthesized PAAc hydrogel. The swelling and viscoelastic properties of the IPHs were evaluated as a function of the content of crosslinker and the application of one F–T cycle. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5789–5794, 2006     

The effects of the pH value of the swelling medium on the kinetics of the swelling of a poly(acrylic acid) hydrogel

The isothermal kinetics curves of the swelling of a poly(acrylic acid) hydrogel in buffer solutions of different pH values (5, 7, and 9) at temperatures ranging from 30 to 40°C were determined. The possibilities of applying the Fick kinetics model and the Peppas equation were examined. It was found that the applicability of these models were limited. The kinetics model of a first‐order chemical reaction was found to describe the swelling kinetics of the PAA hydrogel in all the investigated buffer solution at all the investigated temperatures. Swelling kinetics is determined by the rate of expansion of the network. The kinetic parameters (E_a, ln A) of the swelling of the PAA hydrogel in buffer solutions of different pH values were determined. The activation energy and the pre‐exponential factor of the swelling of the PAA hydrogel in buffer medium decreased with increasing pH value of the swelling medium. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Miscibility of poly(acrylic acid)/poly(methyl vinyl ketone) blend and in vitro application as drug carrier system

A series of poly(acrylic acid)/poly(methyl vinyl ketone) (PAA/PMVK) blends with different compositions were prepared by the solvent casting method. The miscibility of this pair of polymers was investigated by differential scanning calorimetry(DSC), Fourier transform infra-red (FTIR) and X-Ray diffraction (XRD) techniques. An in-vitro cytotoxicity test of the drug-carrier system via MTT (3-(4,5-demethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay revealed no significant cytotoxic effects at concentrations up to 100 µg· ml^?1. The STX/PAA-50 drug carrier systems were also prepared by solvent casting of solutions containing the sulfamethoxazole (STX) used as drug model and PAA/PMVK blend in N.N-dimethylformamide then crosslinked with acidified ethylene glycol. The release dynamic of STX from the prepared hydrogels was investigated in which the diffusion through the polymer matrix, the enhancement of the water solubility of STX, the influence of the initial drug concentration, the pH of the medium, and the effect of the degree of swelling of the polymer matrix on the release dynamic was evaluated. According to the total gastrointestinal transit time estimated by Belzer, the estimate distribution of STX released in the different organs indicated that the performance is obtained with the drug – carrier-system containing equal ratios of polymer and 10 wt% of STX (STX-10/PAA-50).     

Interpenetrating polymer networks based on poly(acrylic acid) and gelatin. I: Swelling and thermal behavior

This article describes the synthesis of full and semi-interpenetrating polymer networks (IPNs) based on poly(acrylic acid) and gelatin as polymers 1 and 2, which were crosslinked sequentially using N,N′-methylene bisacrylamide (B_Am) and glutaraldehyde, respectively. Various samples were prepared by taking varying amounts of acrylic acid and gelatin in the initial feed. Sequential IPNs were prepared by first polymerizing and crosslinking acrylic acid in the presence of gelatin using redox initiators (ammonium persulphate and sodium metabisulphite) and B_Am as a crosslinking agent. Gelatin present in the firm gels was then crosslinked using 4% glutaraldehyde. Characterization of these gels was done by measuring their swelling behavior as a function of pH, temperature, and time. Percent swelling increased with increasing amounts of acrylic acid. The swelling ratio was also determined in the pH range of 1 to 12. Acid/alkali or buffers were used for maintaining pH. A significant increase in the percent swelling was observed when pH of distilled water was above 10. On the other hand, in the case of buffer, the swelling ratio increased with increasing the pH, and a maxima was observed at pH 8.4. A further increase in pH resulted in a decrease in the swelling ratio. Thermal and morphological characterization was done using thermogravimetric analyzer and scanning electron microscopy, respectively. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 217–227, 2001     

Frontal polymerization preparation of poly(acrylamide‐co‐acrylic acid)/activated carbon composite hydrogels for dye removal

A series of poly(acrylic acid‐co‐acrylamide) (PAA)/activated carbon (AC) composite hydrogels were rapidly prepared via frontal polymerization (FP). It was found that an increase in the concentration of AC caused an increase in the front velocity (V_f) and the highest front temperature (T_max). It may be attributed to that AC particles could increase the liquid viscosity of reaction mixture and remain the reaction heat during FP. The Fourier transform infrared and scanning electron microscopy (SEM) confirmed that AC particles had entered the hydrogel network, and many spherical AC particles with an average diameter of 0.5–1 μm had been dispersed homogeneously in the PAA hydrogel matrix. The swelling behavior showed that the equilibrium swelling values of hydrogels increased when the concentration of AC particles increased. Adsorption studies showed that incorporation of AC particles into PAA hydrogel matrix could increase the sites of interaction between the hydrogels and crystal violet molecules and result in an increase of adsorption capacities of hydrogels toward dyes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Bending behaviour of electroresponsive poly(vinyl alcohol)/poly(acrylic acid) semi‐interpenetrating network hydrogel fibres under an electric stimulus

Poly(vinyl alcohol) (PVA) and poly(acrylic acid) (PAA) composite fibres were prepared via solution spinning and subsequently, semi‐interpenetrating networks (SIPN) were obtained by crosslinking the fibres with glutaraldehyde. The hydrogel fibres exhibited bending behaviour under DC electric stimulation. The effects of a number of factors have been systematically studied, including the PAA content within the network, electric voltage imposed across the fibre, the fibre diameter, concentration of the crosslinking agent, pH and ionic strength of the bath solution. Our experimental results show a stable reversibility of bending behaviour under the applied electric field. The degree of bending at equilibrium and the bending speed of the hydrogel fibre increased with the intensity of the applied electric voltage and the PAA content having negatively charged ionic groups within the SIPN. The electroresponsive behaviour of the present SIPN hydrogel fibre was also affected by the aforementioned extrinsic factors. These observations are interpreted in terms of fibre stiffness, fixed charge density and swelling pressure, which depend on the hydrogel equilibrium states in different pH and ionic environments together with the electrochemical reactions under DC electric field. © 2002 Society of Chemical Industry     

Electrical properties of sorbitol‐doped poly(vinyl alcohol)–poly(acrylamide‐co‐acrylic acid) polymer membranes

Solid polymer membranes from poly(vinyl alcohol) (PVA) and poly(acrylamide‐co‐acrylic acid) (PAA) with varying doping ratios of sorbitol were prepared using the solution casting method. The films were examined with Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and AC impedance spectroscopy. The impedance measurements showed that the ionic conductivity of PVA–PAA polymer membrane can be controlled by controlled doping of sorbitol within the polymer blends. The PVA–PAA–sorbitol membranes were found to exhibit excellent thermal properties and were stable for a wide temperature range (398–563K), which creates a possibility of using them as suitable polymers for device applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013