Synthesis and properties of poly(ether ether ketone ketone)–poly(ether sulfone) block copolymers

Poly(ether ether ketone ketone)-poly(ether sulfone) (PEEKK/PES) block copolymers were prepared from the corresponding oligomers via a nucleophilic aromatic substitution reaction, and the M _n of the PEEKK segment was fixed at 12,000, while the M _n's of the PES segment ranged from 250 to 12,680. The different properties of the copolymers were investigated by differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD), thermogravimetric analysis (TGA), and dynamic mechanical analysis (DMA). The results showed that the relationship between T_g and compositions of copolymers approximately followed the formula 1/T_g = W₂/T_g2. The PES content and the segment length of the copolymers had a significant influence on their melting points and crystallization behavior. The thermal properties and dynamic mechanical behavior of the copolymers were also studied. In the study of isothermal crystallization, the copolymers have the same nucleation mechanism and crystal growth as that of pure PEEKK. Owing to the introduction of the PES segment into the PEEKK main chain, it increases the free energy which forms the critical crystal nucleus and produces a resistant action to the whole crystallization process of the PEEKK segment. © 1996 John Wiley & Sons, Inc.     

Synthesis and characterization of poly(ether sulfone) and poly(ether sulfone ketone) copolymers

Poly(ether sulfone) and poly(ether sulfone ketone) copolymers (I–V) were synthesized by the nucleophilic substitution reaction of 4,4′-dihydroxy diphenyl sulfone (DHDPS, A) with various mole proportions 4,4′-difluoro benzophenone (DFBP, B) and 4,4′-difluoro diphenyl sulfone (DFDPS, C) using sulfolane as solvent in the presence of anhydrous K₂CO₃. The polymers were characterized by physicochemical and spectroscopic techniques. All polymers were found to be amorphous, and the glass transition temperature (T_g) was found to increase with the sulfonyl content of the polymers. ¹³C-nuclear magnetic resonance (NMR) spectral data was interpreted in terms of the compositional triads, BAB, BAC, CAC, ABA, and ABB, and indicate that transetherification occurs at high concentration of DFBP units in the polymer (IV). The good agreement between the observed and calculated feed ratios validates the triad analysis. Thermal decomposition studies reveal that the thermal stability of the polymers increases with increase in the carbonyl content in the polymer. Activation energies for thermal decomposition were found to be in the range of 160–203 kJ mol⁻¹ with the cleavage of ϕ SO₂ bond being the preponderant mode of decomposition and depended on the block length of the sulfonyl unit. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 2113–2121, 1999     

Synthesis and characterization of poly(ether sulfone) copolymers

Poly(ether sulfone) copolymers I–V were synthesized by the nucleophilic substitution reaction of 4,4-dichlorodiphenyl sulfone with varying mole proportions of 4,4-isopropylidene diphenol (bisphenol A) and 4,4-dihydroxydiphenyl sulfone (bisphenol S) using sulfolane as the solvent in the presence of anhydrous K₂CO₃. The polymers were characterized by different physicochemical techniques. The glass transition temperature was found to decrease with increase in the concentration of bisphenol A units in the polymers. All polymers were found to be amorphous. Thermogravimetric studies showed that all the polymers were stable up to 400°C with a char yield of about 36% at 900°C in a nitrogen atmosphere. ¹³C-NMR spectral analysis reveals that bisphenol S-based triads are preferentially formed compared to bisphenol-A triads, indicating greater reactivity of bisphenol S toward dichlorodiphenyl sulfone. The overall activation energy for the thermal decomposition of bisphenol A-based polymer (1) is much higher than that of bisphenol S-based polymer ( II ). This was attributed to the modification of the backbone of polymer I during the initial cleavage of the C—CH3 bond of the isopropyledene group. Polymer II decomposes by cleavage of the C—SO2 bond. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 743–750, 1998     

Thermal studies of blends of poly(phenylene sulfide) (PPS) with poly(phenylene sulfide sulfone) (PPSS) and with poly(phenylene sulfide ether) (PPSE)

The miscibilities of poly(phenylene) sulfide/poly(phenylene sulfide sulfone) (PPS/PPSS) and poly(phenylene) sulfide/poly(phenylene sulfide ether) (PPS/PPSE) blends were invesigated in terms of shifts of glass transition temperatures T_g of pure PPS, PPSS, a dn PPSE. The crystallization kinetics of PPS/PPSS blends was also studied as a function of molar composition. The PPS/PPSS and PPS/PPSE blends are respectively partially and fully miscible. PPSE shows a plasticizing effect on PPS as does PPS on PPSS, which necessarily improves te processibility in the respective systems. We can control T_g and melting temperature T_m of PPS by varying amounts of PPSE in blends. The melt crystallization temperature T_mc of PPS/PPSE blends was higher than that of the PPSE homopolymer. Therefore, these blends require shorter cycle times in processing than pure PPSE. The overall rate of crystallization for PPS/PPSS blends follows the Avrami equation with an exponent ?2. The maximal rate of crystallization for PPS/PPSS blends occurs at a temperatre higher by 10°C than that for PPS, while the crystallization half time t_1/2 is 4 times shorter. In the cold crystallization range, crystal growth rates increase and Avrami exponents decrease significantly as the temperature increases.     

Synthesis and characterization of poly(ether sulfone)‐graft‐polydimethylsiloxane copolymers

Novel poly(arylene ether sulfone) (PAES) polymers containing polydimethylsiloxane (PDMS) side chains were synthesized and characterized with NMR and Fourier transform infrared spectroscopy. The thermal properties of the copolymers were evaluated with differential scanning calorimetry and thermogravimetric analysis. The polymers showed perfect thermal stability, as the decomposition temperatures were all above 380°C, and exhibited glass‐transition temperatures in the range 130–188°C. Furthermore, the surface properties of the copolymers were evaluated by X‐ray photoelectron spectroscopy and contact angle analysis. The results show that the hydrophobic abilities of the graft copolymer surfaces were improved significantly compared to PAES through the introduction of the PDMS chains. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Thermally crosslinkable poly(phenylene sulfide)/poly(ether sulfone)/polymerization of monomer reactant–polyimide blends

The effects of thermally crosslinkable polymerization of monomer reactant–polyimide (POI) on the miscibility, morphology, and crystallization of partially miscible poly(ether sulfone) (PES)/poly(phenylene sulfide) (PPS) blends were investigated with differential scanning calorimetry and scanning electron microscopy. The addition of POI led to a significant reduction in the size of PPS particles, and the interfacial tension between PPS and crosslinked POI was smaller than that between PES and crosslinked POI. During melt blending, crosslinking and grafting reactions of POI with PES and PPS homopolymers were detected; however, the reaction activity of POI with PPS was much higher than that with PES. The crosslinking and grafting reactions were developed further when blends were annealed at higher temperatures. Moreover, POI was an effective nucleation agent of the crystallization of PPS, but crosslinking and grafting hindered the crystallization of PPS. The final effect of POI on the crystallinity of the PPS phase was determined by competition between the two contradictory factors. The crosslinking and grafting reactions between the two components was controlled by the dosage of POI in the blends, the premixing sequence of POI with the two components, the annealing time, and the temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2906–2914, 2002; DOI 10.1002/app.10287     

Reactive reinforcement of the interface of poly(ether sulfone)/poly(phenylene sulfide) polymer blend by PMR–POI

The effect of polymerization of monomer reactant–polyimide (POI) as the interfacial agent on the interface characteristics, morphology features, and crystallization of poly(ether sulfone)/poly(phenylene sulfide) (PES/PPS) blends were investigated using a scanning electron microscope, FTIR, WAXD, and XPS surface analysis. It was found that the interfacial adhesion was enhanced, the particle size of the dispersed phase was reduced, and the miscibility between PES and PPS was improved by the addition of POI. It was also found that POI was an effective nucleation agent of the crystallization for PPS. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1297–1306, 2002     

Crystallization and melting behavior of poly(p‐phenylene sulfide) in blends with poly(ether sulfone)

Crystallization and melting behaviors of poly(p‐phenylene sulfide) (PPS) in blends with poly(ether sulfone) (PES) prepared by melt‐mixing were investigated by differential scanning calorimetry (DSC). The blends showed two glass transition temperatures corresponding to PPS‐ and PES‐rich phases, which increased with increasing PES content, indicating that PPS and PES have some compatibility. The cold crystallization temperature of the blended PPS was a little higher than that of pure PPS. Also, the heats of crystallization and melting of the blended PPS decreased with increasing PES content, indicating that the degree of crystallinity decreased with an increase of PES content. The isothermal crystallization studies revealed that the crystallization of PPS is accelerated by blending PPS with 10 wt % PES and further addition results in the retardation. The Avrami exponent n was about 4 independent on blend composition. The activation energy of crystallization increased by blending with PES. The equilibrium melting point decreased linearly with increasing PES content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1686–1692, 1999     

Synthesis and characterization of hexafluoroisopropylidene bisphenol poly(arylene ether sulfone) and polydimethylsiloxane segmented block copolymers

A series of hexafluoroisopropylidene bisphenol poly(arylene ether sulfone) (BAF PAES) segmented block copolymers with varying fractions of polydimethylsiloxane (PDMS) were synthesized by a condensation reaction of hydroxyl-terminated BAF PAES and dimethylamino endcapped PDMS. The segmented block copolymers have high thermal stability. The BAF PAES homopolymer exhibits a tensile modulus of 1700 MPa and an elongation at break of 16%. Copolymerizing BAF PAES with increasing molecular weight amounts of PDMS results in tensile properties ranging from plastic to elastomeric where the elongation is 417% for a segmented block copolymer with 64 wt% PDMS incorporated. The morphological properties of these segmented block copolymers were characterized by atomic force microscopy (AFM), small-angle X-ray scattering (SAXS), and transmission electron microscopy (TEM). AFM and TEM images show the segmented block copolymers were microphase separated, and comparison with bisphenol A (BA) PAES-b-PDMS segmented block copolymers revealed complex differences between the morphological behavior of the two systems. SAXS data of the segmented block copolymers supports AFM and TEM images, indicating microphase separation but little long-range order.     

Effects of heat treatment on the properties of heterogeneous cation permeable membranes from blends of poly(ether sulfone)/sulfonated poly(phenylene sulfide) and phenolphthalein poly(ether ether ketone)/sulfonated poly(phenylene sulfide)

The effects of heat treatment on the properties of membranes prepared from blends of poly(ether sulfone)/sulfonated poly(phenylene sulfide) (SPPS) and phenolphthalein poly(ether ether ketone)/SPPS were studied in detail. The membranes' fundamental properties, including water content, transport number, diffusion coefficient of electrolytes, flux, and so on, changed with both treated temperature and time, whereas the ion‐exchange capacity and electrical resistance remained approximately unchanged. The trends may have been due to the possible structural change resulted from the shrinking of the polymers forming the membranes. Furthermore, the membranes also retained a good physical appearance at temperatures below 220°C. Therefore, a series of heterogeneous membranes with desired conductivities and selectivities as well as proper water contents, which could satisfy different industrial purposes, such as electrodialysis, diffusional dialysis, and proton exchange, were achieved by simple heat treatment for a proper time and at a proper temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 494–499, 2005     

Segmented copolymers of poly(phenylene ether) and polyester

Copolymers of telechelic poly(2,6-dimethyl-1,4-phenylene ether) (PPE) segments with terephthalic methyl ester end groups (PPE-2T, 3500 g/mol) and poly(dodecane terephthalate) (PDDT) were made via a polycondensation reaction in the melt. The inherent viscosities of the segmented copolymers were high. The thermal properties of the copolymers were studied by DMA. The segmented block copolymers had a transparent melt at low (12 wt%) PDDT contents. The segmented block copolymers had at higher PDDT contents a non-transparent melt and two glass transition temperatures. The glass transition temperature of the PPE phase decreased strongly with PDDT content in the copolymer. The glass transition temperature of the PDDT phase increased moderately with PPE content. At low PPE contents the modulus of the PDDT increased strongly with increasing PPE content.     

Preparation of novel heterogeneous cation‐permeable membranes from blends of sulfonated poly(phenylene sulfide) and poly(ether sulfone)

Novel heterogeneous cation‐exchange membranes using poly (ether sulfone)(PES) as binder and sulfonated poly(phenylene sulfide) (SPPS) powder as polyelectrolyte were prepared by the solution casting‐immersion method. Compared with a conventional route for heterogeneous membrane, the steps of milling resin into fine powders and the pressing at high temperature are avoided, and thus permits a simple technique for the preparation of such membrane. The effect of the particle size and loading of SPPS resin on the properties of the membranes such as ion‐exchange capacity, water content, electrical resistance, transport number, diffusion coefficient of electrolytes, etc., have been studied. It is shown that the membrane fundamental properties are largely dependent on both the resin loading and the particle size of SPPS resin. By adjusting these two important parameters, one can obtain heterogeneous membrane with both good conductivity, selectivity, and proper water content for different industrial purposes such as electrodialysis, diffusional dialysis, etc. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 167–174, 2004     

Synthesis and characterization of novel copolymers of poly(ether ketone ketone) and poly(ether ketone sulfone imide)

A new monomer containing sulfone and imide linkages, bis{4-[4-(p-phenoxyphenylsulfonylphenoxy)benzoyl]-1,2-benzenedioyl}-N,N,N′,N′-4,4′-diaminodiphenyl ether (BPSPBDADPE), was prepared by the Friedel–Crafts reaction of bis(4-chloroformyl-1,2-benzenedioyl)-N,N,N′,N′-4,4′-diaminodiphenyl ether with 4,4′-diphenoxydiphenyl sulfone. Novel copolymers of poly(ether ketone ketone) and poly(ether ketone sulfone imide) were synthesized by electrophilic Friedel–Crafts solution copolycondensation of terephthaloyl chloride with a mixture of DPE and BPSPBDADPE. The polymers were characterized by different physico-chemical techniques. The polymers with 10–25?mol% BPSPBDADPE are semicrystalline and had increased T _gs over commercially available PEEK and PEKK (70/30) due to the incorporation of sulfone and imide linkages in the main chains. The polymer IV with 25?mol% BPSPBDADPE had not only high T _g of 194?°C but also moderate T _m of 338?°C, having good potential for melt processing and exhibited high thermal stability and good resistance to common organic solvents.     

Molecular weight determination of poly(phenylene sulfide ether)

Poly(phenylene sulfide ether) and poly(phenylene sulfoxide ether sulfide ether) (PPSOESE) were successfully prepared and their structures were proved by several analytical techniques in the present work. The molecular weight (MW) of PPSOESE, a soluble polymer in common organic solvent at room temperature, was determined by gel permeation chromatography. Based on the conversion reaction of the two polymers, the MW of PPSE was calculated and correlated with its intrinsic viscosity. As a result, the Mark‐Houwink equation for PPSE was concluded. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhanced fracture toughness of epoxy resins with novel amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) triblock copolymers

Amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) (PES‐CTBN‐PES) triblock copolymers with controlled molecular weights of 15,000 (15K) or 20,000 (20K) g/mol were synthesized from amine‐terminated PES oligomer and commercial CTBN rubber (CTBN 1300x13). The copolymers were utilized to modify a diglycidyl ether of bisphenol A epoxy resin by varying the loading from 5 to 40 wt %. The epoxy resins were cured with 4,4′‐diaminodiphenylsulfone and subjected to tests for thermal properties, plane strain fracture toughness (K_IC), flexural properties, and solvent resistance measurements. The fracture surfaces were analyzed with SEM to elucidate the toughening mechanism. The properties of copolymer‐toughened epoxy resins were compared to those of samples modified by PES/CTBN blends, PES oligomer, or CTBN. The PES‐CTBN‐PES copolymer (20K) showed a K_IC of 2.33 MPa m^0.5 at 40 wt % loading while maintaining good flexural properties and chemical resistance. However, the epoxy resin modified with a CTBN/8K PES blend (2:1) exhibited lower K_IC (1.82 MPa m^0.5), lower flexural properties, and poorer thermal properties and solvent resistance compared to the 20K PES‐CTBN‐PES copolymer‐toughened samples. The high fracture toughness with the PES‐CTBN‐PES copolymer is believed to be due to the ductile fracture of the continuous PES‐rich phases, as well as the cavitation of the rubber‐rich phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1556–1565, 2002; DOI 10.1002/app.10390     

Properties and crystallization kinetics of poly(ether ether ketone)‐co‐poly(ether ether ketone ketone) block copolymers

A series of block copolymers composed of poly(ether ether ketone) (PEEK) and poly(ether ether ketone ketone) (PEEKK) components were prepared from their corresponding oligomers via a nucleophlilic aromatic substitution reaction. Various properties of the copolymers were investigated with differential scanning calorimetry (DSC) and a tensile testing machine. The results show that the copolymers exhibited no phase separation and that the relationship between the glass‐transition temperature (T_g) and the compositions of the copolymers approximately followed the formula T_g = T_g1X₁ + T_g2X₂, where T_g1 and T_g2 are the glass‐transition‐temperature values of PEEK and PEEKK, respectively, and X₁ and X₂ are the corresponding molar fractions of the PEEK and PEEKK segments in the copolymers, respectively. These copolymers showed good tensile properties. The crystallization kinetics of the copolymers were studied. The Avrami equation was used to describe the isothermal crystallization process. The nonisothermal crystallization was described by modified Avrami analysis by Jeziorny and by a combination of the Avrami and Ozawa equations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1652–1658, 2005     

Preparation of poly(dimethylsiloxane)–polypeptide block copolymers

Block copolymers composed of poly(dimethylsiloxane) segments linked to polypeptide have been synthesized by reacting primary amine-terminated silicone with N-carboxy anhydrides of amino acids. The amine-terminated silicone was prepared by reacting “living” polysilanolate with γ-aminopropyltriethoxysilane. The block copolymers prepared consisted of segments of poly(DL-phenylalanine) or poly(γ-benzyl-L -glutamate). The block copolymers were purified by extraction with solvents which are selective for the homopolymers. Analysis of the products was accomplished by hydrolysis of the polypeptide segments, infrared spectra, gel permeation chromatography, and elemental analysis. The content of the copolymers ranged from 50 to 87% polypeptide.     

Chemical resistance of carbon fiber-reinforced poly(ether ether ketone) and poly(phenylene sulfide) composites

Studies have been conducted to investigate the aircraft fluid and chemical solvent resistance of the carbon fiber-reinforced poly(phenylene sulfide) (PPS) and poly(ether ether ketone) (PEEK) composites. The solvents and aircraft fluids utilized in this work include hydraulic fluid, paint stripper, JP-4 jet fuel, methyl ethyl ketone, and methylene chloride. The weight gain of the composites as a function of time is measured. Tensile and flexural strength, thermal behavior, and dynamic mechanical properties of the composites are examined. The alteration of crystallinity change of the composites is investigated by X-ray diffraction. It is found that paint stripper degraded the mechanical properties of the composites significantly. Furthermore, crystallization enhancement of the low crystallinity composites in the presence of solvents and aircraft fluids is also observed.     

超支化聚苯硫醚与线性聚苯硫醚的对比表征

以2,4-二氯苯硫酚为原料,采用一步法合成超支化聚苯硫醚。笔者运用红外光谱、拉曼光谱、荧光光谱、示差扫描量热分析、热重分析、广角X-射线衍射、溶解实验等分析手段,对超支化聚苯硫醚和线性聚苯硫醚的基本性能进行了对比。由于两者结构上的差异,使得两者表现出不同的特性。超支化聚苯硫醚具有三取代苯结构,具有很强的荧光效应、完全的不结晶、溶于有机溶剂、热降解温度低于线性聚苯硫醚约60℃等特性。广角X-射线衍射谱图也和结晶、无定型线性聚苯硫醚有很大不同。     

Synthesis,characterization and surface properties of poly(lactic acid)–perfluoropolyether block copolymers

Laboratory‐scale synthesis and morphological and surface energy characterization of triblock A–B–A copolymers based on poly(lactic acid) (PLA; A segment) containing various block lengths of perfluoropolyether (PFPE; B segment) at 5 wt% PFPE content are reported. Incorporation of PFPE segments in PLA lowers significantly both the polar and dispersive components of total surface energy. Total surface energy is lowered from ca 35 to ca 17 mN m^?1 on copolymerization of PLA with 5 wt% PFPE. Thermal analysis data reveal that lower molecular weight PFPE segments lower significantly the glass transition, crystallization and melting temperatures of the PLA matrix. Although block length variation of the PFPE segment does not affect surface energies of copolymer films, smaller PFPE segments increase significantly the low‐temperature modulus as observed from dynamic mechanical analysis. Copyright © 2010 Society of Chemical Industry