Epoxy resin based on 4,4′-dihydroxydiphenysulfone. I. Synthesis and reaction kinetics with 4,4′-diaminodiphenylmethane and 4,4′-diaminodiphenylsulfone

Epoxy resins based on 4,4′-dihydroxydiphenylsulfone (DGEBS) and diglycidyl ether of bisphenol A (DGEBA) were prepared by alkaline condensation of 4,4′-dihydroxydiphenylsulfone (bisphenol S) with epichlorohydrin and by recrystallization of liquid, commercial bisphenol A-type epoxy resin, respectively. Curing kinetics of the two epoxy compounds with 4,4′-diaminodiphenylmethane (DDM) and with 4,4′-diaminodiphenylsulfone (DDS) as well as T_g values of the cured materials were determined by the DSC method. It was found that the ? SO₂? group both in the epoxy resin and in the harener increases T_g values of the cured materials. DGEBS reacts with the used hardeners faster than does DGEBA and the curing reaction of DGEBS begins at lower temperature than does the curing reaction of DGEBA when the same amine is used. © 1994 John Wiley & Sons, Inc.     

Epoxy resin containing the poly(sily ether): Preparation,morphology, and mechanical properties

The poly(sily ether) with pendant chloromethyl groups (PSE) was synthesized by the polyaddition of dichloromethylsilane (DCM) and diglycidylether of bisphenol A (DGEBA) with tetrabutylammonium chloride (TBAC) as a catalyst. This polymer was miscible with diglycidyl ether of bisphenol A (DGEBA), the precursor of epoxy resin. The miscibility is considered to be due mainly to entropy contribution because the molecular weight of DGEBA is quite low. The blends of epoxy resin with PSE were prepared through in situ curing reaction of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐diaminodiphenylmethane (DDM) in the presence of PSE. The DDM‐cured epoxy resin/PSE blends with PSE content up to 40 wt % were obtained. The reaction started from the initial homogeneous ternary mixture of DGEBA/DDM/PSE. With curing proceeding, phase separation induced by polymerization occurred. PSE was immiscible with the 4,4′‐diaminodiphenylmethane‐cured epoxy resin (ER) because the blends exhibited two separate glass transition temperatures (T_gs) as revealed by the means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). SEM showed that all the ER/PSE blends are heterogeneous. Depending on blend composition, the blends can display PSE‐ or epoxy‐dispersed morphologies, respectively. The mechanical test showed that the DDM‐cured ER/PSE blend containing 25 wt % PSE displayed a substantial improvement in Izod impact strength, i.e., epoxy resin was significantly toughened. The improvement in impact toughness corresponded to the formation of PSE‐dispersed phase structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 505–512, 2003     

A simple imide compound as a curing agent for epoxy resin. I. Synthesis and properties

A simple imide compound, 4‐amino‐phthalimide (APH), was synthesized as a curing agent for epoxy resin. APH was prepared from the hydration of 4‐nitro‐phthalimide, which was prepared from the nitration of phthalimide. The chemical structure of APH was verified by IR and ¹H‐NMR spectra. The thermal properties and dielectric constant (ε) of a phosphorus‐containing novolac epoxy resin cured by APH were determined and compared with those of epoxy resins cured by either 4,4′‐diamino diphenyl methane (DDM) or 4,4′‐diamino diphenyl sulfone (DDS). The results indicate that the epoxy resin cured by APH showed better thermal stability and a lower ε than the polymer cured by either DDM or DDS. This was due to the introduction of the imide group of APH into the polymer structure. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Structure characterization,reactivity, and thermal properties of new cyclic phosphine oxide epoxy resin containing tetra-oxirane rings

A new type of epoxy resin, which contained cyclic phosphine oxide and tetra-oxirane rings in the main chain, was synthesized. The structure of the new type of epoxy resin was confirmed by elemental analyses (EA), infrared (IR) spectroscopy, and ¹H nuclear magnetic resonance (NMR) and ¹³C-NMR spectroscopies. In addition, compositions of the new synthesized cyclic phosphine oxide epoxy resin (TGCAO) with three curing agents, for example, bis(3-aminophenyl)ethylphosphine oxide (BEMP), 4,4′-diaminodiphenylmethane (DDM), and 4,4′-diaminodiphenylsulfone (DDS) were used for making a comparison of its curing reactivity, heat, and flame retardancy with those of Epon 828 and DEN438. The reactivities were measured by differential scanning calorimetry. Through the evaluation of thermal gravimetric analysis, those polymers, which were obtained through the curing reactions between the new epoxy resin and three curing agents (BEMP, DDM, and DDS), also demonstrated adequate thermal propeties, as well as a high char yield. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1397–1409, 1998     

The synthesis and properties of new epoxy resin containing phosphorus and nitrogen groups for flame retardancy

A new type of epoxy resin, which contained phosphorus oxide and nitrogen groups in the main chain, was synthesized. The structure of the new type of epoxy resin was confirmed by infrared (IR) spectroscopy, ¹H nuclear magnetic resonance (¹H‐NMR), and ¹³C‐NMR spectroscopic techniques. In addition, compositions of the new synthesized epoxy resin (TGDMO) with three curing agents, for example, bis(3‐aminophenyl) methylphosphine oxide (BAMP), 4,4′‐diaminodiphenylmethane (DDM), and 4,4′‐diaminodiphenylsulfone (DDS), were used for making a comparison of its curing reactivity, heat, and flame retardancy with that of Epon 828 and DEN 438. The reactivities were measured by differential scanning calorimetry (DSC). Through the evaluation of thermal gravimetric analysis (TGA), those polymers which were obtained through the curing reactions between the new epoxy resin and three curing agents (BAMP, DDM, and DDS) also demonstrated excellent thermal properties as well as a high char yield. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 413–421, 1999     

Dielectric relaxation during isothermal curing of epoxy resin with an aromatic amine

The isothermal curing behavior of an epoxy resin system has been monitored by a dielectric measurement whose sensor consisted of a vertical parallel-plate cell based on a three-terminal method. The materials used in the isothermal cure were the diglycidyl ether of bisphenol-A (DGEBA), which was purified from Epon 825 by recrystallization, and 4,4′-diamino diphenyl methane (DDM). A dielectric relaxation was observed during each isothermal cure at temperatures of 70,80,90, and 100°C, which were below the glass transition temperature (T_g) of the reactive DGEBA–DDM system at the gel point. The relaxation is considered to be caused by the transformation from a liquid state to an ungelled glassy state as a result of an increase in molecular weight because gelation followed by a rubbery state did not exist in the temperature range studied. The dielectric relaxation for the DGEBA–DDM system fits the empirical model of the Havriliak–Negami equation. The T_g of the DGEBA–DDM system, which was estimated from the dielectric relaxation time, agreed with the one experimentally determined by differential scanning calorimetry (DSC).     

Torsional braid analysis of the aromatic amine cure of epoxy resins

The cure behavior of diglycidyl ether of bisphenol A (DGEBA) type of epoxy resins with three aromatic diamines, 4,4′-diaminodiphenyl methane (DDM), 4,4′-diaminodiphenyl sulfone (44DDS), and 3,3′-diaminodiphenyl sulfone (33DDS) was studied by torsional braid analysis. For each curing agent the stoichiometry of the resin mixtures was varied from a two to one excess of amino hydrogens per epoxy group to a two to one excess of epoxy groups per amino hydrogen. Isothermal cures of the resin mixtures were carried out from 70 to 210°C (range depending on epoxy—amine mixture), followed by a temperature scan to determine the glass transition temperature (T_g). The times to the isothermal liquid-to-rubber transition were shortest for the DDM mixtures and longest for the 44DDS mixtures. The liquid-to-rubber transition times were also shortest for the amine excess mixtures when stoichiometry was varied. A relatively rapid reaction to the liquid-to-rubber transition was observed for the epoxy excess mixtures, followed by an exceedingly slow reaction process at cure temperatures well above the T_g. This slow process was only observed for epoxy excess mixtures and eventually led to significant increases in T_g. Using time—temperature shifts of the glass transition temperature vs. logarithm of time, activation energies approximately 50% higher were derived for this process compared to those derived from the liquid-to-rubber transition. The rate of this reaction was virtually independent of curing agent and was attributed to etherification taking place in the epoxy excess mixtures. © 1994 John Wiley & Sons, Inc.     

Multifunctional epoxy resins

The curing behavior of epoxy resins prepared by reacting epichlorohydrin with 4,4′-diaminodiphenyl methane (DADPM)/4,4′-diaminodiphenyl ether (DADPE) or 4,4′-diaminodiphenyl sulfone (DDS) was investigated using DDS and tris-(m-aminophenyl)phosphine oxide (TAP) as curing agents. A broad exothermic transition with two maxima were observed in the temperature range of 100–315°C when TAP was used as the curing agent. The effect of varying DDS concentration on curing behavior of epoxy resin was also investigated. Peak exotherm temperature (T_exo) decreased with increasing concentration of DDS, whereas heat of curing (ΔH) increased with an increase in amine concentration up to an optimum value and then decreased. Thermal stability of the resins, cured isothermally at 200°C for 3 h, was investigated using thermogravimetric analysis in a nitrogen atmosphere. Glass fiber-reinforced multifunctional epoxy resin laminates were fabricated and the mechanical properties were evaluated. © 1993 John Wiley & Sons, Inc.     

Cure and glass transition temperature of the bisphenol S epoxy resin with 4,4′‐diaminodiphenylmethane

The curing reaction of bisphenol S epoxy resin (BPSER) with 4,4′‐diaminodiphenylmethane (DDM) was studied by means of torsional braid analysis (TBA) in the temperature range of 393–433 K. The glass transition temperature (T_g) of the BPSER/DDM system is determined, and the results show that the reaction rate increases with increasing the T_g in terms of the rate constant, but decreases with increasing conversion. 1 The T_g of BPSER/DDM is about 40 K higher than BPAER/DDM. The gelation and vitrification time were assigned by the isothermal TBA under 373 K; in addition, an FTIR spectrum was carried out to describe the change of the molecular structure. The thermal degradation kinetics of this system was investigated by thermogravimetric analysis (TGA). It illustrated that the thermal degradation of the BPSER/DDM has n‐order reaction kinetics. 2 © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 794–799, 2000     

Biphenyl liquid crystal epoxy containing flexible chain: Synthesis and thermal properties

A biphenyl type liquid crystal epoxy (LCE) monomer 4,4′-di(2,3-epoxyhexyloxy)biphenyl (LCBP4) containing flexible chain was synthesized and the curing behavior was investigated using 4,4′-diaminodiphenylmethane (DDM) as the curing agent. The effect of curing condition on the formation of the liquid crystalline phase was examined. The cured samples show good mechanical properties and thermal stabilities. Moreover, the relationship between thermal conductivity and structure of liquid crystalline domain was also discussed. The samples show high thermal conductivity up to 0.28–0.31 W/(m*K), which is 1.5 times as high as that of conventional epoxy systems. In addition, thermal conductive filler, Al₂O₃, was introduced into LCBP4/DDM to obtain higher thermal conductive composites. When the content of Al₂O₃ was 80 wt%, the thermal conductivity of the composite reached to 1.86 W/(m*K), while that of diglycidyl ether of bisphenol A (Bis-A) epoxy resin/DDM/Al₂O₃ was 1.15 W/(m*K). Compared with Bis-A epoxy resin, the formation of liquid crystal domains in the cured LCE resin enhanced the thermal conductivity synergistically with the presence of Al₂O₃. Furthermore, the introduction of Al₂O₃ also slightly increased the thermal stabilities of the cured LCE.     

Cure kinetics and catalyzed effect of hydroxyl group of LC diglycidyl ether of bisphenol‐S with aromatic diamines

The curing reactions of liquid crystalline 4,4′‐bis‐(2,3‐epoxypropyloxy)‐sulfonyl‐bis(1,4‐phenylene) (p‐BEPSBP) with 4,4′‐diaminodiphenylmethane (DDM) and 4,4′‐diaminodiphenylsulfone (DDS) were investigated by nonisothermal differential scanning calorimeter (DSC). The relationships of E_a with the conversion α in the curing process were determined. The catalyzed activation of hydroxyl group for curing reaction of epoxy resins with amine in DSC experiment was discussed. The results show that these curing reactions can be described by the autocatalytic ?esták‐Berggren model. The curing technical temperature and parameters were obtained, and the even reaction orders m, n, and ΔS for p‐BEPSBP/DDM and p‐BEPSBP/DDS are 0.35, 0.92, ?81.94 and 0.13, 1.32, ?24.45, respectively. The hydroxyl group has catalyzed activation for the epoxy–amine curing system in the DSC experiment. The average E_a of p‐BEPSBP/DDM is 67.19 kJ mol^?1 and is 105.55 kJ mol^?1 for the p‐BEPSBP/DDS system, but it is different for the two systems; when benzalcohol as hydroxyl group was added to the curing system, the average E_a of p‐BEPSBP/DDM decreases and increases for p‐BEPSBP/DDS. The crystalline phase had formed in the curing process and was fixed in the system. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Acetone—Formaldehyde—Phenol based IPNs for Glass Fibre Reinforced Composite Applications

Abstract

Three component IPNs Glass fibre reinforced composites (GRC) have been prepared from acetone-formaldehyde-phenol (AF-P) resin, Diglycedyl ether of bisphenol-A (DGEBA) (a commercial epoxy resin) and methyl methacrylate (MMA) (a vinyl monomer). The curing catalyst hexamethylene tetramine (HMTA) for AF-P, radical initiators 2,2′-azobisisobutyronitrile (AIBN) for MMA and curing catalyst 4,4′-diamino diphenyl methane (DDM) for epoxy resin were employed. All the IPN GRCs were characterized in terms of their resistance to chemical reagents, thermal behaviour (DSC, TGA) and mechanical properties.     

Synthesis and properties of urethane elastomer-modified epoxy resin having hydroxymethyl group

Synthesis and properties of urethane elastomer-modified epoxy resins were studied. The urethane elastomer-modified epoxy resins were synthesized by the reaction of a 4-cresol type epoxy compound having hydroxymethyl groups (EPCDA) with isocyanate prepolymer. The structure was identified by IR, ¹H NMR and GPC. These epoxy resins (EPCDATDI) were mixed with a commercial epoxy resin (DGEBA) in various ratios. The mixed epoxy resins were cured with a mixture of 4,4′-diaminodiphenylmethane and 3-phenylenediamine (molar ratio 6:4) as a hardener. The curing behaviour of these epoxy resins was studied by DSC. The higher the concentration of EPCDATDI, the higher the onset temperature and the smaller the rate constant (k) of the exothermic cure reaction were. It was considered that the ratio of hydroxymethyl group to epoxide group was very small and the molecular weight of EPCDATDI was large. Therefore, the accelerating effect of the hydroxymethyl group on the epoxide–amine reaction was cancelled by the retardant effect of increased molecular weight and viscosity, and decreased molecular motion. Toughness was estimated by Izod impact strength and fracture toughness (K_1C). On addition of 10 wt% EPCDATDI with low molecular weight (M?_n 6710, estimated by GPC using polystyrene standard samples), Izod impact strength and K_1C increased by 70% and 60%, respectively, compared with unmodified epoxy resin. Glass transition temperatures (T_g) for the cured epoxy resins mixed with EPCDATDI measured by dynamic mechanical spectrometry were the same as those of unmodified epoxy resin. The storage modulus (E′) at room temperature decreased with increasing concentration of EPCDATDI. Toughness and dynamic mechnical behaviour of cured epoxy resin systems were studied based on the morphology.     

Synthesis and properties of trifluoromethyl groups containing epoxy resins cured with amine for low Dk materials

The study synthesized a trifluoromethyl (CF₃) groups with a modified epoxy resin, diglycidyl ether of bisphenol F (DGEBF), using environmental friendly methods. The epoxy resin was cured with 4,4′‐diaminodiphenyl‐methane (DDM). For comparison, this study also investigated curing of commercially available diglycidyl ether of bisphenol A (DGEBA) with the same curing agent by varying the ratios of DGEBF. The structure and physical properties of the epoxy resins were characterized to investigate the effect of injecting fluorinated groups into epoxy resin structures. Regarding the thermal behaviors of the specimens, the glass transition temperatures (T_g) of 50–160°C and the thermal decomposition temperatures of 200–350 °C at 5% weight loss (T_d5%) in nitrogen decreased as amount of DGEBF increased. The different ratios of cured epoxy resins showed reduced dielectric constants (D_k) (2.03–3.80 at 1 MHz) that were lower than those of pure DGEBA epoxy resins. Reduced dielectric constant is related to high electrronegativity and large free volume of fluorine atoms. In the presence of hydrophobic CF₃ groups, the epoxy resins exhibited low moisture absorption and higher contact angles. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Miscibility and mechanical properties of tetrafunctional epoxy resin/phenolphthalein poly(ether ether ketone) blends

Phenolphthalein poly(ether ether ketone) (PEK‐C) was found to be miscible with uncured tetraglycidyl 4,4′‐diaminodiphenylmethane (TGDDM), which is a type of tetrafunctional epoxy resin (ER), as shown by the existence of a single glass transition temperature (T_g) within the whole composition range. The miscibility between PEK‐C and TGDDM is considered to be due mainly to entropy contribution. Furthermore, blends of PEK‐C and TGDDM cured with 4,4′‐diaminodiphenylmethane (DDM) were studied using dynamic mechanical analysis (DMA), Fourier‐transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). DMA studies show that the DDM‐cured TGDDM/PEK‐C blends have only one T_g. SEM observation also confirmed that the blends were homogeneous. FTIR studies showed that the curing reaction is incomplete due to the high viscosity of PEK‐C. As the PEK‐C content increased, the tensile properties of the blends decreased slightly and the fracture toughness factor also showed a slight decreasing tendency, presumably due to the reduced crosslink density of the epoxy network. SEM observation of the fracture surfaces of fracture toughness test specimens showed the brittle nature of the fracture for the pure ER and its blends with PEK‐C. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 598–607, 2001     

Curing and Morphology of BPA Epoxy Resin/LC Epoxy Resin PEPEB Composites

Liquid crystalline epoxy resin (LC epoxy resin) – p-phenylene di{4-[2-(2,3-epoxypropyl)ethoxy]benzoate} (PEPEB) was synthesized. The mixture of PEPEB with bisphenol-A epoxy resin (BPAER) was cured with a curing agent 4,4-diamino-diphenylmethane (DDM). The curing process and thermal behavior of this system were investigated by differential scanning calorimeter (DSC) and torsional braid analysis (TBA). The morphological structure was measured by polarizing optical microscope (POM) and scanning electron microscope (SEM). The results show that the initial curing temperature Ticu (gel point) of this system is 68.1°C, curing peak temperature T _pcu is 102.5°C, and the disposal temperature T _fcu is 177.6°C. LC structure was fixed in the cured epoxy resin system. The curing kinetics was investigated by dynamic DSC. Results showed that the curing reaction activation energy of BEPEB/BPAER/DDM system is 22.413 kJ/mol. The impact strength is increased 2.3 times, and temperature of mechanical loss peak is increased to 23°C than the common bisphenol-A epoxy resin, when the weight ratio of BEPEB with BPAER is 6 100.     

Cure kinetics and thermal stability of micro and nanostructured thermosetting blends of epoxy resin and epoxidized styrene‐block‐butadiene‐block‐styrene triblock copolymer systems

The compatibility of styrene‐block‐butadiene‐block‐styrene (SBS) triblockcopolymer in epoxy resin is increased by the epoxidation of butadiene segment, using hydrogen peroxide in the presence of an in situ prepared catalyst in water/dichloroethane biphasic system. Highly epoxidized SBS (epoxy content SBS >26 mol%) give rise to nanostructured blends with epoxy resin. The cure kinetics of micro and nanostructured blends of epoxy resin [diglycidyl ether of bisphenol A; (DGEBA)]/amine curing agent [4,4′‐diaminodiphenylmethane (DDM)] with epoxidized styrene‐block‐butadiene‐block‐styrene (eSBS 47 mol%) triblock copolymer has been studied for the first time using differential scanning calorimetry under isothermal conditions to determine the reaction kinetic parameters such as kinetic constants and activation energy. The cure reaction rate is decreased with increasing the concentration of eSBS in the blends and also with the lowering of cure temperature. The compatibility of eSBS in epoxy resin is investigated in detailed by Fourier transform infrared spectroscopy, optical and transmition electron microscopic analysis. The experimental data of the cure behavior for the systems, epoxy/DDM and epoxy/eSBS(47 mol%)/DDM show an autocatalytic behavior regardless of the presence of eSBS in agreement with Kamal's model. The thermal stability of cured resins is also evaluated using thermogravimetry in nitrogen atmosphere. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Poly(Amide‐Imide)s Based on Amino‐Terminated Oligoimides

Abstract

An amino‐terminated oligoimide was prepared by the Michael addition reaction of ethylene bis‐maleimide (EBM) and 4,4′‐diamnio diphenyl‐sulfone (DDS) at an EBM:DDS molar ratio of 1:2. The poly(amide‐imide)s (PAI)s were prepared by condensation of this EBMDDS oligoimide with various aliphatic bisesters. The resultant PAIs were characterized by elemental analysis, IR spectral studies, and the number average molecular weight estimated by non‐aqueous conductometric titration and thermogravimetry. The curing reaction of an epoxy resin [a diglycidyl ether of bis‐phenol‐A (DGEBA)] with PAIs was monitored by differential scanning calorimetry (DSC). Glass‐ and carbon‐reinforced laminates of PAI‐epoxy resin were also prepared and characterized.     

Low-temperature fast curable behavior and properties of bio-based carbon fiber composites based on resveratrol

Environmentally friendly materials are an integral part of sustainable chemistry, and bio-based polymer composites are an important class of materials. The manufacture of composites is expected to reduce or even eliminate the use of adjuvants, considering the importance of reducing energy consumption and avoiding health and environmental risks. In this study, a phenyl-containing, polyfunctional, bio-based epoxy resin (TGER) was synthesized, and carbon fiber-reinforced, bio-based epoxy resin composites were fabricated by vacuum-assisted resin infusion using two aromatic amine curing agents, 4,4′-diaminodiphenylmethane (DDM) and 3,3′-diethyl-4,4′-diaminodiphenylmethane (DEDDM). Curing reactions and rheological behavior studies showed that TGER had higher curing reactivity toward DDM and DEDDM than to diglycidyl ether of bisphenol A (DGEBA) and possessed good processability. The results indicated that the resveratrol-based epoxy resin displayed low-temperature fast curing properties. The evaluation of the mechanical properties of the carbon fiber composites showed that the flexural strengths of CF/TGER/DDM and CF/TGER/DEDDM were 520 and 628 MPa, respectively. The initial decomposition temperature of CF/TGER composites is above 200°C. Furthermore, the carbon fiber–reinforced biopolymers possess excellent heat resistance. Therefore, carbon fiber-reinforced, resveratrol-based epoxy resin composites are promising candidates as alternatives to petroleum-based high-performance carbon fiber composites.     

Improvement of Elastic Modulus and Thermal Stability of Epoxy Resin Using New Curing Agents

New curing agents 2,5-diamino-1,3,4-thiadiazole (DATD) and N-(4-hydroxybenzal) N'(4′-hydroxyphenyl) thiourea (HHPT) were synthesised and characterized using FT-IR, 1H-NMR and 13C-NMR analysis. The curing reactions were studied for the epoxy resin diglycidyl ether of bisphenol-A (DGEBA) using new curing agents along with the conventional aromatic diamine 4,4′-diamino diphenyl methane (DDM) for comparison purpose. The curing profiles of DDM, DATD and DATD/HHPT towards DGEBA were examined by Differential Scanning Calorimetry (DSC). Elastic modulus and thermal stability of the cured resins were evaluated using DMA and TGA analysis. When compared with DDM and DATD, the DATD/HHPT curing system accelerated the curing rate due to the presence of phenol molecules in the HHPT. Furthermore, the DATD/HHPT-cured epoxy resin demonstrated higher elastic modulus along with better thermal stability.