AZ91镁合金化学镀镍前处理的工艺（英文）

研究了H3PO4+Na2Mo O4、H3PO4+KMn O4和H3PO4+Na3PO4三种酸洗工艺以及NH4HF2活化工艺等前处理工艺对AZ91HP镁合金化学镀的影响。通过金相实验及极化实验,结果表明,AZ91HP镁合金经H3PO4+Na3PO4酸洗后再经NH4HF2工艺活化处理后施镀,可获得表面光亮、结合力强和耐蚀性能较好的镍-磷镀层。镁合金酸洗处理后表面的平整程度会影响其化学镀层平整度和光亮度,而活化处理后表面的粗糙程度则影响镀层和基体的结合力。     

前处理工艺对AZ91D镁合金直接化学镀的影响

通过不同的酸洗配方工艺,对比讨论了前处理工艺对AZ91D镁合金直接化学镀镍(DEN)的沉积速率及镀层与基底结合性能的影响。结果表明,AZ91D镁合金表面活化后,虽然粗糙界面由于更多的结合点和更大的机械互锁作用,能提高镀层与基体间的结合力,但是镀层结合的致密程度对结合力的影响作用更为显著。以磷酸和氟化钾为酸洗配方的前处理工艺,更适合AZ91D镁合金直接化学镀。     

AZ91HP镁合金化学镀镍磷及镀层性能研究

目的提高AZ91HP镁合金的耐蚀及耐磨性,扩大其应用范围。方法采用H_3PO_4+Na_3PO_4酸洗液+NH_4HF_2活化的无铬前处理工艺,再直接化学镀,获得镍磷合金镀层,随后对镀层进行了热处理。对施镀前后基体和镀层的形貌、显微硬度和耐蚀性等进行了表征分析。结果 AZ91HP镁合金经H_3PO_4+Na_3PO_4酸洗+NH_4HF_2活化的无铬处理后施镀,形成的细小胞状组织均匀致密,结合力良好,镀层结构以非晶态相为主,耐腐蚀性比基体显著增高。经热处理后,镀层的硬度明显增高且在400℃时获得的镀层硬度最高,但耐蚀性有所下降。结论 H_3PO_4+Na_3PO_4酸洗体系+NH_4HF_2活化为镁合金提供了一种环保而有效的化学镀前处理方法,获得了以非晶态相为主的Ni-P镀层,提高了基体的耐腐蚀性,镀后热处理可进一步提高镀层的硬度。     

AZ91D镁合金电镀铜前处理工艺研究

用电化学法和表面形貌观察研究AZ91D镁合金电镀铜前酸洗活化及浸锌过程的一些主要影响因素．结果表明,镁合金的酸洗活化液组成对镁合金表面的光洁度有较大影响,复合组分（C2H2O4·2H2O＋NaF）酸洗活化效果明显好于单一组分（C2H2O4·2H2O）的酸洗活化液,酸洗活化的温度以常温为宜．最佳酸洗活化工艺为：12g／L...     

汽车发动机冷却液中镁合金缓蚀剂的研究

采用XRD、电化学极化曲线、化学浸泡等实验方法，研究了腐蚀性水体系中单种无机盐、复配无机盐缓蚀剂对AZ91D镁合金的缓蚀作用，并用正交优化设计确定了Na2MoO4+Na2SiO3+KMnO4复配无机盐缓蚀剂的优化配方；研究了水-乙二醇（1：1）防冻液基础液体系中缓蚀剂对AZ91D镁合金的缓蚀作用.结果表明，在腐蚀性水中KMnO4、Na3PO4、Na2MoO4和NaF对AZ91D镁合金有一定的缓蚀作用，Na2B4O7不具有缓蚀作用，有可能加速其腐蚀；复配Na3PO4+KMnO4及Na2MoO4+Na2SiO3+KMnO4对AZ91D镁合金腐蚀有缓蚀作用，而Na3PO4+Na2B4O7会加速其腐蚀.在水-乙二醇体系中，Na2S对AZ91D镁合金腐蚀有较好的缓蚀作用；确定了2种适用于水-乙二醇中的有机-无机复合缓蚀剂配方，缓蚀效率分别为98.1％和94.3％.     

AZ31镁合金电镀前处理工艺研究

采用扫描电子显微分析、失重实验等手段和方法探讨AZ31镁合金电镀前处理工艺。结果表明,采用CrO₃+Fe(NO₃)₃+KF酸洗后试样表面光亮,基本无失重;采用H₃PO₄+NH4HF活化,可有效去除试样表层氧化物,增强基体和浸锌层的结合力;采用硫酸盐浸锌工艺可获得致密的浸锌层。通过分析温度、电流密度、pH值对浸锌层的影响规律,获得了最佳的浸锌工艺：30g/L ZnSO_4?7H₂O, 150 g/L K₄P₂O₇10H₂O,7 g/L KF, 5g/L Na₂CO₃, 温度70℃～75℃, pH=10.2～10.4 ,浸锌时间10 min。在此前处理基础上电镀锌,镀层和基体结合力较好。     

镁合金一步酸洗活化前处理工艺

采用失重法、扫描电子显微镜、动电位极化曲线等,对比研究了经四种酸洗活化配方处理后的镁合金的腐蚀行为,并研究了不同酸洗活化配方对后续化学镀Ni-Sn-P镀层的形貌、成分及结合力的影响。结果表明,一步酸洗活化工艺对镁合金的浸蚀效果良好,表面粗糙均匀,无腐蚀产物堆积,与基底的"互锁"效应增强。经一步酸洗活化处理的镁合金基底的耐蚀性最佳。经一步酸洗活化后的镁合金电化学镀层能更有效地保护镁合金基体。     

一种无铬低氟的镁合金化学镀镍前处理工艺

为了获得一种更加环保的镁合金化学镀镍前处理工艺,通过多种方法和手段对比研究了3种不同的酸洗活化工艺对镁合金化学镀镍的影响。通过开路电势-时间(OCP-t)曲线解释了不同前处理方法导致不同沉积速度的原因。采用SEM、EDX和XRD分析发现,3种工艺所得镀层均为高磷合金镀层(P含量约为11%),镀层的表面形貌和结构比较接近。动电位极化曲线表明,采用H_3PO_4+HNO_3酸洗,K_4P_2O_7和NH_4HF_2分别活化的前处理工艺所得镀层耐蚀能力略优于传统工艺镀层。新工艺酸洗液对镁合金存在横向的刻蚀,可增强镀层与基底间的机械咬合作用,使得镀层的结合力更强。     

镁合金AZ91表面化学镀镍层的制备及性能研究

为了优化镁合金表面化学镀镍工艺,降低施镀过程中的污染,研究了AZ91镁合金表面直接化学镀镍工艺,并应用SEM对镀层表面形貌进行观察,通过EDS及XRD对镀层成分及物相进行了分析,采用划线划格法、静态浸泡法分别对镀层与镁合金基体的结合力、镀层的防腐蚀性能进行了分析.研究结果表明:AZ91镁合金表面可通过直接化学镀镍获得结合力良好、表面硬度较高的镍镀层.镀层的成分分析显示:由于NaH2PO2发生自身氧化还原反应,镀层中存在少量P.在3.5%NaCl溶液中的静态腐蚀试验结果表明:镀层的耐腐蚀性能良好,对合金基体可以起到较好的防护作用.     

镁合金表面化学镀 Ni-P 和 Ni-P-SiC 的对比

目的提高镁合金的耐磨性、耐蚀性,扩大其应用领域。方法采用"磷酸+钼酸铵酸洗→HF活化"的方法进行前处理,直接在AZ91D镁合金表面化学镀Ni-P合金镀层和Ni-P-SiC复合镀层。对两种镀层的表面和截面形貌、成分、结构、硬度、耐蚀性及耐磨性进行了系统比较。结果在Ni-P合金镀层中引入SiC粉末后,镀层的胞状颗粒细化,硬度提高至643HV,但其腐蚀电流密度有所增大。结论与Ni-P合金镀层相比,Ni-P-SiC复合镀层的耐蚀性有所下降,但耐磨性能大大提高。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。