Sn-3.0Ag-0.5Cu/Cu焊点可靠性研究

采用铺展面积法研究了Sn-3.0Ag-0.5Cu无铅钎料在不同温度下的润湿性能,同时探讨了150℃等温时效对Sn-3.0Ag-0.5Cu/Cu焊点界面组织及力学性能的影响。结果表明,随着钎焊温度的升高,Sn-3.0Ag-0.5Cu钎料的润湿性能明显增加。焊后钎料/Cu界面处对应的金属间化合物为Cu6Sn5相,经150℃时效,界面层的形貌由原来的齿状逐渐转化为层状,且厚度随着时效时间的增加而增加。发现界面层金属间化合物厚度与时效时间的二次方根成线性关系。对焊点在时效过程中的力学性能进行分析,发现Sn3.0Ag0.5Cu/Cu焊点的力学性能随着时效时间的增加逐渐降低,时效初期,焊点的力学性能下降较快,后期趋于平缓。     

感应自加热重熔无铅焊料凸台的剪切失效模式

通过两次高频感应重熔制备了Cu焊盘上S n3．5Ag焊料和Sn3．0Ag0．5Cu焊料凸台,并进行了120℃下的老化试验以及老化试件的剪切强度试验,分析了不同老化时间下两种无铅焊料凸台的剪切断裂模式。焊料凸台的剪切载荷-位移曲线的特征以及对焊料凸台剪切断口的扫描电镜形貌分析结果表明,不同老化时间下无铅焊料凸台的剪切断裂表现为塑性、韧性和脆性三种断裂模式。对凸台焊料合金的组织以及界面观察结果表明,随老化时间不断生长的脆性金属间化合物层以及焊料组织粗大是致使断裂失效模式转变的根本原因。     

La对Sn3.5Ag0.5Cu钎料界面组织和性能的影响

通过SEM和EDAX等,研究了La添加量对Sn3.5Ag0.5Cu钎料与Cu基体焊合界面IMC微观组织及性能的影响。结果表明:添加不同量的La均对Sn3.5Ag0.5Cu与Cu基体焊合后的组织有细化作用并增强其力学性能。其中以w(La)达到0.05%时最优,剪切强度可提高10.7%。材料热力学理论计算结果表明,La具有"亲Sn"倾向,添加少量La到Sn3.5Ag0.5Cu钎料中,可减小Cu6Sn5/Cu界面Sn的活度,降低IMC的长大驱动力。     

Y2O3增强Sn-3Ag-0.5Cu复合无铅钎料

研究了稀土氧化物颗粒增强复合无铅钎料Sn-3Ag-0.5Cu-Y2O3的钎焊接头的显微组织形貌、性能特点及有关影响机制.结果表明:Y2O3增强颗粒均匀分布于Sn-3Ag-0.5Cu钎料基体中,不仅细化了钎焊接头中共晶相Ag3Sn和Cu6Sn5相颗粒尺寸,而且也显著提高了钎焊接头的剪切强度.另外适量Y2O3颗粒的添加对钎料润湿性影响不大.     

激光和热风重熔方法制得微小无铅钎焊接头中金锡化合物的形貌和分布

随着电子器件及产品向小型化、微型化方向发展,微小接头中的金含量会大比例提高。焊盘表面的金在重熔过程中会与钎料合金中的锡发生反应生成金属间化合物（IMCs）,而IMCs的形貌和分布受控于重熔工艺,并会对接头可靠性产生重大影响。本研究中采用激光、热风重熔方法和直径为120微米的锡球制得了焊盘表面镀有不同厚度金层的直角结构接头,用来研究重熔工艺对金锡Iits形貌和分布的影响。研究发现：激光重熔微小接头中,大部分的金锡IMCs都呈针状或树枝状,并分布于钎料于焊盘的界面处。对于焊盘表面镀有厚度为0.1微米金的焊盘界面处并未发现大块装的金锡IMCs。而对于采用热风重熔方法得到的接头,大块状和短棒状的金锡IMCs会遍布整个接头。本文分析了造成金锡IMCs形貌和分布在两种接头中出现巨大差异的原因。     

SnAgCu焊点电迁移诱发IMC阴极异常堆积

为了研究电迁移过程中焊点与焊盘界面金属问化合物(IMC)的变化,在28℃下,对无铅Sn3.0Ag0.5Cu焊点进行了6.5A直流电下的电迁移实验.结果发现,通电144h后,阳极侧IMC层变厚,平均达到10.12 μm;阴极侧IMC层大部分区域变薄至0.86μm,局部出现Cu焊盘的溶解消失,但在界面边缘处出现Cu3Sn5...     

无铅钎料凸点超声倒装焊接可行性的研究

近年来,较高熔点的无铅钎料合金已经开始在微电子互连制造中广泛应用,传统的红外或热风等整体加热方法所造成芯片和印刷线路的热影响问题更加突出。采用不加热源的超声波倒装焊接方法,有助于解决上述热影响问题。本文以Sn3．5Ag无铅钎料凸点为对象,验证了室温下Sn3．5Ag无铅钎料凸点超声倒装焊接的可行性和可操作性,分析了多类互连焊点的宏观形态和显微组织,研究表明添加钎剂和改变焊接材料体系均可显著改善互连焊点成型。     

Ti对Sn0.7Cu无铅钎料润湿性和界面的影响

研究了Ti的加入对Sn0.7Cu无铅钎料润湿性能以及钎料/Cu界面微观组织的影响.结果表明:在Sn0.7Cu中添加微量Ti,提高了钎料的润湿性能,可使铺展面积提高5％左右,当钎焊时间为3s时,界面金属间化合物(IMC)形貌由原来的扇贝状变为锯齿状;随着钎焊时间延长,Sn0.7Cu/Cu和Sn0.7Cu0.008Ti/C...     

添加Sb和LaB6对Sn3.0Ag0.5Cu/Cu界面IMC生长的影响

研究了Sb和稀土化合物的添加对Sn3.0Ag0.5Cu无铅焊料焊接界面金属间化合物层生长的影响。研究结果表明,固态反应阶段界面化合物层的生长快慢排序如下:v(SAC0.4Sb0.1LaB6/Cu)v(SAC0.4Sb/Cu)v(SAC0.1LaB6/Cu)v(SAC/Cu)。计算各种界面IMC生长的激活能Q结果表明,Sn3.0Ag0.5Cu/Cu界面IMC生长的激活能最高,为92.789 kJ,其他焊料合金Sn3.0Ag0.5Cu0.4Sb0.1LaB6/Cu,Sn3.0Ag0.5Cu0.1LaB6/Cu和Sn3.0Ag0.5Cu0.4Sb/Cu界面IMC生长的激活能分别为85.14,84.91和75.57 kJ。在老化温度范围内(≤190℃),Sn3.0Ag0.5Cu0.4Sb0.1LaB6/Cu的扩散系数(D)最小,因而其界面化合物的生长速率最慢。     

Sn基无铅钎料与Cu基板间化合物Cu_6Sn_5的研究进展

主要介绍了Sn基无铅钎料和Cu基板在界面处反应生成的金属间化合物Cu6Sn5与焊接点可靠性的关系。综述了近年来Cu6Sn5的研究进展,内容包括:Sn基无铅钎料在Cu基板上形成的Cu6Sn5的生长形态、晶体取向、生长动力学以及纳米颗粒对界面Cu6Sn5尺寸及形貌的影响。     

Effect of reaction time on mechanical strength of the interface formed between the Sn-Zn(-Bi) solder and the Au/Ni/Cu bond pad

In this work, the shear strengths and the interfacial reactions of Sn-9Zn, Sn-8Zn-1Bi, and Sn-8Zn-3Bi (wt.%) solders with Au/Ni/Cu ball grid array (BGA) pad metallization were systematically investigated after extended reflows. Zn-containing Pb-free solder alloys were kept in molten condition (240°C) on the Au/electrolytic Ni/Cu bond pads for different time periods ranging from 1 min. to 60 min. to render the ultimate interfacial reaction and to observe the consecutive shear strength. After the shear test, fracture surfaces were investigated by scanning electron microscopy equipped with an energy dispersive x-ray spectrometer. Cross-sectional studies of the interfaces were also conducted to correlate with the fracture surfaces. The solder ball shear load for all the solders during extended reflow increased with the increase of reflow time up to a certain stage and then decreased. It was found that the formation of thick Ni-Zn intermetallic compound (IMC) layers at the solder interface of the Au/electrolytic Ni/Cu bond pad with Sn-Zn(-Bi) alloys deteriorated the mechanical strength of the joints. It was also noticed that the Ni-Zn IMC layer was larger in the Sn-Zn solder system than that in the other two Bi-containing solder systems.     

Characteristics of the Sn-Pb eutectic solder bump formed via fluxless laser reflow soldering

In an attempt to develop a fluxless reflow solder bumping process, the effects of processing variables, which include energy input rate and time, and the shape of solder disk on the microstructure of the solder/Cu pad interface and the shear strength of the joints were investigated. It was demonstrated that a proper combination of the variables could lead to the formation of a spherical solder bump with shear strength comparable to that formed via the conventional reflow soldering process. In addition, the kinetics of Cu pad dissolution into the solder during laser heating was modeled numerically to elucidate intermetallic formation mechanism at the solder/Cu pad interface. Jointly appointed by CAAM at POSTECH     

Effect of substrate metallization on interfacial reactions and reliability of Sn-Zn-Bi solder joints

The scope of this paper covers a comprehensive study of the lead-free Sn-Zn-Bi solder system, on Cu, electrolytic Ni/Au and electroless Ni(P)/Au surface finishes. This includes a study of the shear properties, intermetallic compounds at the substrate-ball interface and dissolution of the under bump metallization. The Sn-8Zn-3Bi (wt.%) solder/Cu system exhibited a low shear load with thick IMCs formation at the interface. The dissolution of the Cu layer in the Sn-Zn-3Bi solder is higher than that of the other two Ni metallizations. It was found that the formation of a thick Ni-Zn intermetallic compound (IMC) layer at the solder interface of the electrolytic Ni bond pad reduced the mechanical strength of the joints during high temperature long time liquid state annealing. The solder ball shear-load for the Ni(P) system during extended reflow increased with an increase of reflow time. No spalling was noticed at the interface of the Sn-Zn-3Bi solder/Ni(P) system. Sn-8Zn-3Bi solder with electroless Ni(P) metallization appeared as a good combination in soldering technology.     

回流焊对SnAgCuBi/Cu焊点IMC及剪切强度的影响

利用金相显微镜和扫描电镜对多次回流焊后的Sn-0.3Ag-0.7Cu-xBi/Cu焊点IMC和剪切断口形貌进行了观察和分析。结果表明:Bi的加入提高了接头剪切强度,且随着Bi含量的增加而增加,当w(Bi)为4.5%时达最大值45.07MPa,同时Bi的加入有效抑制了焊点IMC的增长。经过5次回流焊后,未加入Bi的焊点剪切强度由24.55MPa下降到20.82MPa,而加入w(Bi)为3.0%的焊点剪切强度由35.95MPa下降到32.46MPa。     

The influence of solder composition on the impact strength of lead-free solder ball grid array joints

This study aims to investigate the shear and tensile impact strength of solder ball attachments. Tests were conducted on Ni-doped and non-Ni-doped Sn-0.7wt.% Cu, Sn-37wt.% Pb and Sn-3.0wt.% Ag-0.7wt.% Cu solder ball grid arrays (BGAs) placed on Cu substrates, which were as-reflowed and aged, over a wide range of displacement rates from 10 to 4000 mm/s in shear and from 1 to 400 mm/s in tensile tests. Ni additions to the Sn-0.7wt.% Cu solders has slowed the growth of the interface intermetallic compounds (IMCs) and made the IMC layer morphology smooth. As-reflowed Ni-doped Sn-0.7wt.% Cu BGA joints show superior properties at high speed shear and tensile impacts compared to the non-Ni-doped Sn-0.7wt.% Cu and Sn-3.0wt.% Ag-0.7wt.% Cu BGAs. Sn-3.0wt.% Ag-0.7wt.% Cu BGAs exhibit the least resistance in both shear and tensile tests among the four compositions of solders, which may result from the cracks in the IMC layers introduced during the reflow processes.     

Morphology and Pull Strength of Sn-Ag(-Co) Solder Joint with Copper Pad

In order to clarify the effect of the addition of Co to the Sn-Ag solder, the formation and growth of an intermetallic compound (IMC) at the interface between Sn-Ag(-Co) solders and a Cu pad were investigated, and the joint strength of the solder with a Cu pad was also evaluated by a bump pull test. Binary Sn-3.5mass%Ag solder was used as the basic solder, and Sn-3.5mass%Ag-xCo solders (x = 0.1 mass%, 0.3 mass%, and 0.5 mass%) were specially prepared as Co-added solders. For the reflow process, specimens were heated in a radiation furnace at 523 K for 60 s. For the aging process, some specimens were then heat-treated in an oil bath at 423 K for 168 h, 504 h, and 1008 h. The results show that the addition of Co to the Sn-Ag solder strongly affected the formation and growth of the IMC at the interface. The results of the pull test clearly show that all solders had similar pull strengths, regardless of the Co addition, although the IMC morphology at the interface of the Sn-Ag-Co solder was quite different from that of the binary Sn-3.5Ag solder. (Received . . . ; accepted . . . )     

Mechanical and Electrical Properties of Cu/Sn-3.5Ag/Cu Ball Grid Array (BGA) Solder Joints after Multiple Reflows

The microstructural evolution, die shear strength, and electrical resistivity of Cu/Sn-3.5Ag (wt.%)/Cu ball grid array (BGA) solder joints were investigated after 1 to 10 reflows using scanning electron microscopy (SEM), transmission electron microscopy (TEM), electron probe microanalysis (EPMA), bonding testing, and a four-point probe station. A Cu₆Sn₅ intermetallic compound (IMC) was formed at both the upper and lower interfaces after one reflow. The IMC thickness increased at the lower interface with increasing reflow number, whereas the IMC morphology and thickness remained virtually unchanged at the upper interface, irrespective of the reflow number. The amount of Cu₆Sn₅ IMC contained in the solder ball increased with increasing reflow number. These microstructural evolutions with increasing reflow number strongly affected the mechanical and electrical properties of the solder joint.     

Aging study on interfacial microstructure and solder-ball shear strength of a wafer-level chip-size package with Au/Ni metallization on a Cu pad

Eutectic solder balls (63Sn-37Pb) joined to Cu pads with an Au/Ni metallization have been widely used in wafer-level chip-size package (WLCSP) technology for providing electrical and mechanical interconnections between components. However, some reliability issues must be addressed regarding the intermetallic compounds (IMCs). The formation of a brittle IMC layer between the solder/Cu pad interface impacts considerably upon the solder-ball shear strength. In addition, it will degrade the long-term operating reliability of the WLCSP. This study investigates, by means of experiments, the growth of the IMC layer under isothermal aging for the eutectic Sn-Pb solder reflowed on a Cu pad with an Au/Ni metallization. Forming the Cu pad with an Au/Ni metallization was achieved by a simple semiconductor-manufacturing process. The effects of the intermetallic layer on solder-ball shear strength were examined for various parameters, including the thickness of the Au layer, solder-ball size, and the diameter of the Cu pad. Experimental results indicate that two IMC layers, Au_0.5Ni_0.5Sn₄ and Ni₃Sn₄, form at the solder/Cu pad interface after aging. The Au_0.5Ni_0.5Sn₄ intermetallic layer dominates the total thickness of the IMC layer and grows with aging time while the solder-ball shear strength decreases after aging. The degradation of the solder-ball shear strength was found to be caused mainly by the formation of the Au_0.5Ni_0.5Sn₄ layer. The experimental results established that a thinner Au layer on Cu pad can effectively control the degradation of solder-ball shear strength, and this is especially true for smaller ball sizes.     

Plasma reflow bumping of Sn-3.5 Ag solder for flux-free flip chip package application

A new flux-free reflow process using Ar+10%H/sub 2/ plasma was investigated for application to solder bump flip chip packaging. The 100-/spl mu/m diameter Sn-3.5wt%Ag solder balls were bonded to 250-/spl mu/m pitch Cu/Ni under bump metallurgy (UBM) pattern by laser solder ball bonding method. Then, the Sn-Ag solder balls were reflowed in Ar+H/sub 2/ plasma. Without flux, the wetting between solder and UBM occurred in Ar+H/sub 2/ plasma. During plasma reflow, the solder bump reshaped and the crater on the top of bump disappeared. The bump shear strength increased as the Ni/sub 3/Sn/sub 4/ intermetallic compounds formed in the initial reflow stage but began to decrease as coarse (Cu,Ni)/sub 6/Sn/sub 5/ grew at the solder/UBM interface. As the plasma reflow time increased, the fracture mode changed from ductile fracture within the solder to brittle fracture at the solder/UBM interface. The off-centered bumps self-aligned to patterned UBM pad during plasma reflow. The micro-solder ball defects occurred at high power prolonged plasma reflow.     

Effect of Trace Diamond Nanoparticle Addition on the Interfacial, Mechanical, and Damping Properties of Sn-3.0Ag-0.5Cu Solder Alloy

In the present study, small amounts of nanodiamond particles were added to Sn-3.0Ag-0.5Cu eutectic solder to investigate the growth kinetics of the intermetallic compound (IMC) layer at ball grid array pad/solder interfaces. The IMC growth behavior was found to be comparatively slower than that of plain solder joints due to a change in the diffusivity of the constituent atoms and the thermodynamic parameters of elemental affinity. The solder joints containing nanodiamond particles consistently showed higher hardness and strength than plain Sn-3.0Ag-0.5Cu solder joints, after a number of reflow cycles. The hardness of the doped solder was enhanced due to the homogeneous dispersion of nanoparticles, refining IMC phases which act as reinforcements in the solder matrix and as barriers to movement of dislocations. The fracture surface after shear testing of plain solder exhibited a relatively smooth fracture surface, while doped solder joints showed ductile failures with very rough dimpled surfaces. The damping capacity of the doped solder was better than the plain solder at a wide range of temperatures, and the solder with nanoparticle diamond exhibited lower internal friction.