Impact Factors for Horizontally Curved Composite Box Girder Bridges

This paper presents a method for determining the dynamic impact factors for horizontally curved composite single- or multicell box girder bridges under AASHTO truck loading. The bridges are modeled as three-dimensional structures using commercially available software. The vehicle is idealized as a pair of concentrated forces, with no mass, traveling in two circumferential paths parallel to the curved centerline of bridges. An extensive parametric study is conducted, in which over 215 curved composite box girder bridge prototypes are analyzed. The key parameters considered in this study are: Number of cells, number of lanes, degree of curvature, arc span length, slope of the outer steel webs, number and area of bracing and top chord systems, and truck(s) speed and truck(s) positioning. Based on the data generated from the parametric study, expressions for dynamic impact factors for longitudinal moment, reaction, and deflection are proposed as function of the ratio of the arc span length to the radius of curvature. The results from this study would enable bridge engineers to design horizontally curved composite box girder bridges more reliably and economically. Furthermore, the results can be used to potentially increase the live-load capacity of existing bridges to prevent posting or closing of the bridge.     

Impact Factors for Curved Continuous Composite Multiple-Box Girder Bridges

The results from a parametric study on the impact factors for 180 curved continuous composite multiple-box girder bridges are presented. Expressions for the impact factors for tangential flexural stresses, deflection, shear forces and reactions are deduced for AASHTO truck loading. The finite-element method was utilized to model the bridges as three-dimensional structures. The vehicle axle used in the analysis was simulated as a pair of concentrated forces moving along the concrete deck in a circumferential path with a constant speed. The effects of bridge configurations, loading positions, and vehicle speed on the impact factors were examined. Bridge configurations included span length, span-to-radius of curvature ratio, number of lanes, and number of boxes. The effect of the mass of the vehicle on the dynamic response of the bridges is also investigated. The data generated from the parametric study and the deduced expressions for the impact factors would enable bridge engineers to design curved continuous composite multiple-box girder bridges more reliably and economically.     

Full-Scale Test and Analysis of a Curved Steel-Box Girder Bridge

Since the first edition of the AASHTO Guide Specifications for Horizontally Curved Steel Girder Highway Bridges was published in 1980, there have been two more editions including many revisions to the specifications. Some changes were based on valid research results and others were based on limited or uncertain research results and information. The current edition of the specifications contains provisions that may result in unreasonably conservative load capacity ratings. In this paper, the results of field tests and analyses conducted on the Veterans’ Memorial curved steel-box girder bridge are discussed. Test and analytical results show: (1) current AASHTO guide specifications regarding the first transverse stiffener spacing at the simple end support of a curved girder may be too conservative for bridge load capacity ratings; (2) current AASHTO guide specifications may greatly overestimate the dynamic loadings of curved box girder bridges with long span lengths; and (3) a plane grid finite-element model of about 20 elements per span in the longitudinal direction can be used to analyze curved multigirder bridges with external bracings located only over supports. The research results are instructive and applicable to bridge design and bridge load-rating activities.     

Design for Shear in Curved Composite Multiple Steel Box Girder Bridges

Modern highway bridges are often subject to tight geometric restrictions and, in many cases, must be built in curved alignment. These bridges may have a cross section in the form of a multiple steel box girder composite with a concrete deck slab. This type of cross section is one of the most suitable for resisting the torsional, distortional, and warping effects induced by the bridge’s curvature. Current design practice in North America does not specifically deal with shear distribution in horizontally curved composite multiple steel box girder bridges. In this paper an extensive parametric study, using an experimentally calibrated finite-element model, is presented, in which simply supported straight and curved prototype bridges are analyzed to determine their shear distribution characteristics under dead load and under AASHTO live loadings. The parameters considered in this study are span length, number of steel boxes, number of traffic lanes, bridge aspect ratio, degree of curvature, and number and stiffness of cross bracings and of top-chord systems. Results from tests on five box girder bridge models verify the finite-element model. Based on the results from the parametric study simple empirical formulas for maximum shears (reactions) are developed that are suitable for the design office. A comparison is made with AASHTO and CHBDC formulas for straight bridges. An illustrative example of the design is presented.     

Literature Review in Analysis of Box-Girder Bridges

The curvilinear nature of box girder bridges along with their complex deformation patterns and stress fields have led designers to adopt approximate and conservative methods for their analyses and design. Recent literature on straight and curved box girder bridges has dealt with analytical formulations to better understand the behavior of these complex structural systems. Few authors have undertaken experimental studies to investigate the accuracy of existing methods. This paper presents highlights of references pertaining to straight and curved box girder bridges in the form of single-cell, multiple-spine, and multicell cross sections. The literature survey presented herein deals with: (1) elastic analysis, and (2) experimental studies on the elastic response of box girder bridges.     

Routing and Permitting Techniques of Overweight Vehicles

Overweight vehicles require permits to cross the highway bridges, which are designed for “design load vehicles” (prescribed in the national standards). A new, fast, and robust method is presented for the verification of bridges, which requires minimal input only: the axle loads, axle spacing, the bridge span(s), and the superstructure type. The bridge can be a single or a multispan girder, an arch bridge, a frame structure, or a box girder. The overweight vehicle may operate within regular traffic or it may cross the bridge at a given lane position while other traffic is prohibited on the bridge. The method is illustrated by numerical examples for deck-girder bridges and for a box girder.     

Distribution of Wheel Loads on Continuous Steel Spread-Box Girder Bridges

Composite concrete-steel spread (multispine) box girder bridges remain one of the most common types constructed. Current design practices in North America recommend few analytical methods for the design of such bridges in simply supported construction. However, the effects of continuous construction have not been dealt with fully. In designing a continuous bridge, it is important to determine the maximum negative and positive stresses, maximum reactions, and shears in the bridge subjected to various loadings. This paper presents an extensive parametric study using a finite-element model in which 60 continuous bridge prototypes of various geometries, each subjected to various loading conditions, are analyzed for the distribution of flexural stresses, deflection, shears, and reactions. The parameters considered in the study are span length, number of spread boxes, and number of lanes. Distribution factors for maximum flexural stresses, deflection, shears, and reactions, suitable for design, are deduced for AASHTO truck loading. Results from tests on five box girder bridge models verify the finite-element model. A design example is presented to illustrate the use of the deduced formulas for the distribution factors.     

Dynamic Analysis of Curved Continuous Multiple-Box Girder Bridges

The use of horizontally curved composite multiple-box girder bridges in modern highway systems is quite suitable in resisting torsional and warping effects induced by highway curvatures. Bridge users react adversely to vibrations of a bridge and especially where torsional modes dominate. In this paper, continuous curved composite multiple-box girder bridges are analyzed, using the finite-element method, to evaluate their natural frequencies and mode shapes. Experimental tests are conducted on two continuous twin-box girder bridge models of different curvatures to verify and substantiate the finite-element model. Empirical expressions are deduced from these results to evaluate the fundamental frequency for such bridges. The parameters considered herein are the span length, number of lanes, number of boxes, span-to-radius of curvature ratio, span-to-depth ratio, end-diaphragm thickness, number of cross bracings, and number of spans.     

Construction of a Horizontally Curved Steel I-Girder Bridge. Part I: Erection Sequence

In the case of horizontally curved steel I-girder bridges, girder and cross-frame members are frequently detailed for erection in the no-load condition as a matter of convention. As a result, it is imperative that the erection sequence used to construct such bridges be comprehensively studied to ensure that the no-load condition can be achieved in the field and that significant superstructure component fit-up problems do not occur. The current research investigates the erection of a recently constructed horizontally curved steel I-girder bridge, in which significant difficulties were encountered during erection. The bridge erection is recreated through an analytical simulation using a detailed nonlinear finite element model. The analytical results demonstrate that a condition that closely resembles the no-load condition can be achieved in the field during construction with the proper implementation of temporary support structures; and that the difficulties encountered during the erection of the subject bridge superstructure could not be attributed to the erection scheme followed.     

Simply Supported Curved Cellular Bridges: Simplified Design Method

The use of curved composite bridges in interchanges of modern highway systems has become increasingly popular for economic and aesthetic considerations. Bridges with a concrete deck composite with a steel multicell section can adequately resist torsional and warping effects induced by high curvature. Although current design practices in North America recommend few analytical methods for the design of curved multicell box girder bridges, economical requirements in the design process point to a need for a simplified design method. This paper summarizes the results from an extensive parametric study, using the finite-element method, in which simply supported curved composite multicell bridge prototypes are analyzed to evaluate the moment and deflection distributions between girders, as well as the axial forces expected in the bracing system, due to truck loading as well as dead load. Results from tests on four, 1∕12 linear-scale, simply supported curved composite concrete deck-steel multicell bridge models are used to substantiate and verify the analytical modeling. The parameters considered in the study are cross-bracing system, aspect ratio, number of lanes, number of cells, and degree of curvature. Based on the data generated from the parametric study, expressions for moment and deflection distribution factors are deduced. Expressions for the maximum axial force in bracing members are also derived. An illustrative design example is presented.     

Erection Procedure Effects on Deformations and Stresses in a Large-Radius, Horizontally Curved, I-Girder Bridge

Special attention is required in the construction of horizontally curved steel I-girder bridges due to coupled effects of primary bending and torsional forces. Misguided steel erection procedures can lead to undesired stresses, deflections, and rotations in these types of bridges, resulting in a structure with misaligned geometry and in an unknown state of stress. Further complicating the issue, little guidance related to curved bridge behavior during construction is provided by current design codes, leaving contractors and designers uncertain as to the most appropriate steps to take to achieve an efficient, safe structure. A horizontally curved, six-span steel I-girder bridge located in central Pennsylvania that experienced severe geometric misalignments and fit-up complications during steel erection was studied to investigate curved girder behavior during construction. The structure was monitored during corrective procedures intended to realign it with the design geometry, and field data used to calibrate a three-dimensional computer model generated via SAP2000. The techniques and assumptions proven in the calibration process were used to create a numerical model of a three-span continuous portion of the bridge, which was the subject of several analyses exploring the effects erection sequencing, implementation of upper lateral bracing, and use of temporary supports had on the final deformed shape of the curved superstructure. Findings indicated that using paired girder erection produced smaller radial and vertical deformations than single girder techniques for this structure, and that the use of lateral bracing between the fascia and adjacent interior girders and the placement of temporary shoring towers at span quarter points are both effective means of further reducing levels of deflection.     

Construction of a Horizontally Curved Steel I-Girder Bridge. Part II: Inconsistent Detailing

The erection of horizontally curved steel I-girder bridges tends to be more complex than the erection of straight steel I-girder bridges. The erection of a curved steel I-girder bridge can be further complicated when the cross-frame members and girders are detailed inconsistently in an effort to force bridge components into some desirable geometric condition. Inconsistent detailing involves the intentional specification of cross-frame members that are either too long or too short to align with girder connector plates properly so as to force the girders into a given position, resulting in connection misalignments that must be resolved by applying external forces to the bridge components. The current research investigates the erection of a recently constructed horizontally curved steel I-girder bridge and highlights the fact that practice of inconsistent detailing can lead to very formidable and costly fit-up problems in the field; especially when girder sizes are large.     

Research on Finite Element Determinant of Orthotropic Plate in Steamlined Steel Box Girder

A new type of streamlined girder bridge with orthotropic plates steel box girder is evaluated via testing and analysis. Although the use of finite element modeling has become indispensable for the detailed calculation of certain details and connections, an analytical approach remains a very effective method to determine the internal forces and moments in the box girder. Two new theoretical analysis models are undertaken to study the behavior of aimed bridge. The FE determinants of the two models are built. The validity of the proposed methods is checked by full finite element calculation using shell elements. In addition, a total experimental model is set up to verify the reliability of computational models. The computation results compare well with the experimental results. It is illustrated that it is an effective method to predict properties of this kind of bridges.     

Shear Lag of Thin-Walled Curved Box Girder Bridges

This note investigates the influence of shear lag for thin-walled curved box girders, including longitudinal warping. The longitudinal warping displacement functions of the flange slabs are approximated by a cubic parabolic curve instead of a quadratic curve of Reissner's method. On the basis of the thin-walled curved bar theory and the potential variational principle, the equations of equilibrium considering the shear lag, bending, and torsion (St. Venant and warping) for a thin-walled curved box girder are established. The closed-form solutions of the equations are derived, and Vlasov's equation is further developed. The obtained formulas are applied to calculate the shear lag effects for curved box girder bridges. Numerical examples are presented to verify the accuracy and applicability of the present method.     

Live-Load Analysis of a Curved I-Girder Bridge

Horizontally curved, steel girder bridges are often used in our modern infrastructural system. The curve in the bridge allows for a smother transition for traffic, which creates better road travel. However, some of the disadvantages of horizontally curved bridges are that they are more difficult to analyze, design, and sometimes construct in comparison to conventional straight bridges. This study focuses on a three-span, curved steel I-girder bridge which was tested under three boundary condition states to determine it’s response to live load. The measured live-load strains were used to calibrate a finite-element model. The finite-element design moments and distribution factors for the three condition states were then compared with the results based on the V-load method. These different boundary conditions provided the researchers a unique opportunity to evaluate the impact that these changes had on the bridges behavior. It was found that while the V-load method produced positive bending moments that were close to the finite-element moments for some of the girders, this was a result of the V-load moment being unconservative and the distribution factor being conservative.     

Seismic Performance Assessment of Simply Supported and Continuous Multispan Concrete Girder Highway Bridges

Seismic evaluations of typical concrete girder bridges are conducted for both a multispan simply supported and a multispan continuous girder bridge common to the Central and Southeastern United States. These evaluations are performed for an approximate hazard level of 2% in 50?years by performing nonlinear time history analyses on three-dimensional analytical models. The results show significant vulnerabilities in the reinforced concrete columns, the abutments, and also in unseating of the girders. In general, the longitudinal loading of the bridges results in larger demands than the transverse loading. However, the simply supported bridge sustains bearing deformations in the transverse direction which are on the same order as their longitudinal response. These results suggest that both longitudinal and transverse loading are significant and should be considered when performing seismic hazard analyses of these bridges.     

Segmental and Conventional Precast Prestressed Concrete I-Bridge Girders

Conventional precast I-girder bridge systems are widely used in North America for short and medium spans, up to 45 m. Spliced standard precast I-girder segments made continuous by longitudinal posttensioning have been used for spans of up to 75 m, making them far more competitive with the steel plate girder and concrete box girder alternatives. The span and∕or girder spacing capabilities of the standard I-sections of Nebraska University, Florida, American Association of State Highway and Transportation Officials-Precast∕Prestressed Concrete Institute (AASHTO-PCI), and Canadian Prestressed Concrete Institute (CPCI) are determined for both spliced posttensioned and conventional pretensioned girder systems. This investigation shows that the Florida and Nebraska University I-sections are the most efficient girders for spliced posttensioned and conventional pretensioned bridges, respectively. Using a nonlinear optimization program, the optimum girder shape is found to be a bulb-tee for spliced posttensioned girders and a quasi-symmetrical I-section for conventional pretensioned girders. A new set of five I-sections that achieve a balanced efficiency for both spliced posttensioned and conventional pretensioned bridge girder systems are proposed. Three examples of alternative preliminary bridge designs using both the existing standard and the newly proposed I-sections illustrate the practicality of the presented results.     

Load Distribution for a Highly Skewed Bridge: Testing and Analysis

The American Association of State Highway and Transportation Officials (AASHTO) specifications provide formulas for determining live load distribution factors for bridges. For load distribution factors to be accurate, the behavior of the bridge must be understood. While the behavior of right-angle bridges and bridges with limited skews is relatively well understood, that of highly skewed bridges is not. This paper presents a study aimed at developing a better understanding of the transverse load distribution for highly skewed slab-on-steel girder bridges. The study involved both a diagnostic field test of a recently constructed bridge and an extensive numerical analysis. The bridge tested and analyzed is a two-span, continuous, slab-on-steel composite highway bridge with a skew angle of 60°. The bridge behavior is defined based on the field test data. Finite-element analyses of the bridge were conducted to investigate the influence of model mesh, transverse stiffness, diaphragms, and modeling of the supports. The resulting test and analytical results are compared with AASHTO’s Load and Resistance Factor Design formulas for live load distribution to assess the accuracy of the current empirical formulas.