交联直写海藻酸盐水凝胶中空纤维的凝胶率与溶胀度

以海藻酸钠为原料、氯化钙为交联剂,反应直写制备海藻酸钙水凝胶中空纤维及组织工程支架.纤维的凝胶率和溶胀度直接影响支架的成形质量与所装载细胞的存活率.浸取分离所直写中空纤维的未交联部分,分析材料浓度对凝胶率的影响;以滴注凝固浴制备的海藻酸钙微球为对照组,分析直写工艺的溶胀度表现.结果表明,以4%海藻酸钠与3%氯化钙材料交联直写的中空纤维凝胶率和纤维形貌较好地满足了直写工艺的要求;随着海藻酸钠浓度的增加,中空纤维的溶胀度先减小后小幅升高并趋于稳定;随着氯化钙浓度的增加,凝胶纤维的溶胀度逐渐减小;反应直写工艺由于较小的两相接触表面,其溶胀度比凝固浴制备凝胶微球高2～5倍,更高的含水率有利于保障所装载细胞的活性和传质.     

基于半互穿凝胶的复合抑尘剂的制备及性能研究

以海藻酸钠为基体,乙酸乙烯酯和丙烯酸为反应单体,利用接枝共聚技术对海藻酸钠进行了分子改性,再加上氯化钙生成的海藻酸钙凝胶进行凝胶半互穿,制备了一种环保、无污染的抑尘剂,通过对抑尘性能进行测试得出抑尘剂润湿性强,抑尘效果好。     

双乳化-凝胶法制备单分散海藻酸钙微球及其载BSA研究

采用双乳化-凝胶法制备了单分散的海藻酸钙凝胶微球,并通过正交试验系统考察了海藻酸钠浓度、氯化钙浓度、表面活性剂浓度、搅拌速度和油水比对海藻酸钙凝胶微球粒径及形貌的影响。在优化的条件下,制备出了平均粒径为4μm、单分散和球形度好的海藻酸钙凝胶微球。包埋模型药物牛血清白蛋白(BSA)的过程中,以去离子水作为洗涤液洗涤海藻酸钙微球时,BSA的包封率仅为13%左右;当水洗液的pH值为3.2时,BSA的包封率提高到66%左右,载药率可达16%,这是海藻酸钙pH值响应溶胀和BSA与海藻酸盐之间静电作用的结果。微球中BSA的体外释放曲线表明,该系统具有在模拟胃液中释药速率慢、释药量低、模拟肠液中释药迅速的特性。因此,双乳化-凝胶法制备海藻酸钙微球有望成为制备蛋白类药物控释制剂的一种新方法,以达到靶向快速给药的目的。     

阿维菌素海藻酸钙微球制备与表征

[目的]制备阿维菌素海藻酸钙微球,并评价其相关性能。[方法]采用内源乳化法制备阿维菌素海藻酸钙微球,以溶胀率、产率为考察指标,结合正交设计试验对微球的制备工艺进行优化,并利用光学显微镜和傅立叶变换红外光谱仪对微球进行了观察和表征。[结果]阿维菌素海藻酸钙微球最佳工艺为海藻酸钠和Span 80的质量浓度均为15 g/L、海藻酸钠与CaCO3质量比3∶1、水油两相体积比为1∶2。所制备的微球外观呈规则球形,载药率和包封率分别达到84.21%和20.16%。体外药物释放试验表明,阿维菌素海藻酸钙微球48 h累计释放率为78.61%。[结论]所制备的阿维菌素海藻酸钙微球具有良好的缓释性,提高了农药的利用率。     

双层聚乙烯醇微凝胶的合成及其在药物载体中的应用(英文)

首先采用细乳液聚合工艺合成了聚乙酸乙烯酯种子微球,继续滴加单体和交联剂获得核壳不同交联度的聚乙酸乙烯酯微球,经皂化反应后制备了生物相容性的双层结构聚乙烯醇微凝胶;以水杨酸为模拟药物,研究了微凝胶对药物的吸附和释放行为,发现载药微凝胶的药物释放符合0级动力学,在12 h内释放了85%。     

海藻酸钙软骨材料的凝胶化过程研究

以软骨材料的研究和应用为背景,在分析了海藻酸钙作为软骨材料的研究现状和应用前景的基础上,制备了海藻酸钙凝胶微球软膏填充材料,考察了材料的粒径、含水量、凝胶速率、力学性能和溶胀性能,了解了材料组分、配比对材料性能的影响;通过对凝胶微球表面形貌的观察察,了解了凝胶微球表面的特点,通过红外光谱的分析,了解了凝胶反应对凝胶材料谱峰的影响.     

紫薯花色苷果胶/海藻酸钙复合凝胶球的制备及性能研究

采用离子凝胶法制备了荷载紫薯花色苷的果胶/海藻酸钙凝胶球,以弹性、硬度、紫薯花色苷包封率为评价指标,探讨氯化钙浓度、果胶与海藻酸钠比例、胶凝时间对指标的影响。结果表明,随着氯化钙浓度、果胶添加量的增大及胶凝时间延长,凝胶球的硬度和包封率增大。当果胶/海藻酸钠比为7∶1,氯化钙浓度为9%,胶凝时间为5 min时,此时制备的凝胶球硬度最大,弹性适度,包封率最大。SEM扫描电镜显示,凝胶球具有明显的核壳结构。溶胀和模拟胃肠液实验显示,凝胶球在碱性和肠液中易溶胀,在结肠中释放最大,达到54.8%。     

丙烯腈接枝改性海藻酸钙水凝胶中水杨酸的释放行为

将海藻酸钙水凝胶与丙烯腈单体进行不同程度的接枝共聚改性,再由FTIR加以分析,并测定包埋了水杨酸模拟药物的改性海藻酸钙水凝胶在不同介质中的药物释放量。实验表明,改性海藻酸钙水凝胶的药物释放量既与介质有关,也取决于接枝率的大小。     

紫薯花色苷果胶/海藻酸钙复合凝胶球的制备及性能研究

采用离子凝胶法制备了荷载紫薯花色苷的果胶/海藻酸钙凝胶球,以弹性、硬度、紫薯花色苷包封率为评价指标,探讨氯化钙浓度、果胶与海藻酸钠比例、胶凝时间对指标的影响。结果表明,随着氯化钙浓度、果胶添加量的增大及胶凝时间延长,凝胶球的硬度和包封率增大。当果胶/海藻酸钠比为7∶1,氯化钙浓度为9%,胶凝时间为5 min时,此时制备的凝胶球硬度最大,弹性适度,包封率最大。SEM扫描电镜显示,凝胶球具有明显的核壳结构。溶胀和模拟胃肠液实验显示,凝胶球在碱性和肠液中易溶胀,在结肠中释放最大,达到54.8%。     

乳化法制备海藻酸钙/聚组氮酸微胶囊

采用乳化法制备海藻酸钙微球及海藻酸钙/聚组氨酸载药微胶囊,并考察不同海藻酸钠浓度、氯化钙浓度对微球表面形态、粒径分布、载药性能及微胶囊控制释放性能的影响。结果表明海藻酸钠浓度主要影响微球的粒径大小,氯化钙浓度主要影响微球的分散程度及粒径分布,微球载药量均随海藻酸钠浓度及氯化钙浓度的增加而减小,所制备的微胶囊均无明显的突释现象。     

Preparation and characterization of interpenetrating network beads of poly(vinyl alcohol)‐grafted‐poly(acrylamide) with sodium alginate and their controlled release characteristics for cypermethrin pesticide

Interpenetrating network polymeric beads of poly(vinyl alcohol)‐grafted‐acrylamide with sodium alginate have been prepared by crosslinking with glutaraldehyde. Cypermethrin, a widely used pesticide, was loaded with 80% efficiency in these hydrogel beads. The beads were characterized by Fourier transform infrared spectroscopy to confirm the grafting. Scanning electron microscopy was used to know the morphology of the beads. Equilibrium swelling experiments indicated that swelling of the beads decreased with an increase in crosslinking. The in vitro release studies were performed under static conditions and the release data have been fitted to an empirical relation to estimate the transport parameters. The diffusion coefficients have been calculated for the transport of pesticide through the polymeric beads using the initial time approximation method. These values showed decrease with increasing crosslinking as well as increasing pesticide loading. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 552–560, 2002; DOI 10.1002/app.10306     

Protein‐imprinted polyurethane‐grafted calcium alginate hydrogel microspheres

Protein‐imprinted polyurethane‐grafted calcium alginate hydrogel microspheres were prepared and characterized. The samples were investigated with optical microscopy, scanning electron microscopy, ¹³C‐NMR, and Fourier transform infrared spectroscopy. We proved that polyurethane side chains were successfully grafted, and this led to a relatively rough and dense surface. The samples exhibited better swelling durability when applied in specific adsorption tests. The adsorption kinetic and recognition properties indicated that the imprinted modified microspheres had excellent rebinding affinity toward the target proteins. Moreover, the influence of the preassembly pH, rebinding pH, and grafting ratio on the adsorption capacity and imprinting efficiency (IE) were systematically investigated. The study results suggest that the modified samples possessed a higher IE toward the target protein under the optimum pH and grafting ratio. Upon polyurethane grafting modification, the alginate hydrogel microspheres showed improved mechanical stability and recognition specificity. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42140.     

Investigation of radiation grafting of vinyl acetate onto (tetrafluoroethylene–perfluorovinyl ether) copolymer films

A study has been made of radiation-induced grafting of vinyl acetate (VAc) on to (tetrafluoroethylene–perfluorovinyl ether) copolymer (PFA). Effects of grafting conditions such as inhibitor and monomer concentrations and irradiation dose on the grafting yield were investigated. In this grafting system, ammonium ferrous sulphate (Mohr′s salt) was added to the monomer-solvent mixture to minimize the homopolymerization of VAc and the most suitable concentration was found to be 2.0 wt%. It was found that the dependence of the initial grafting rate on monomer concentration is of the order 1.5. The degree of grafting tends to level off at high irradiation doses due to the recombination of formed free radicals without initiating graft polymerization. Some properties of the prepared graft copolymer such as swelling behaviour, electrical conductivity, thermal and mechanical properties were also investigated. The electrical conductivity was improved by hydrolysis of poly(vinyl acetate) in the grafted chains to their respective vinyl alcohols. The tensile properties were improved by grafting; however, the elongation percent decreased. The DTA data showed thermal stability of such graft copolymers for temperatures up to 300°C, but stability decreased at higher temperatures.     

Controlled release study of carbaryl insecticide from calcium alginate and nickel alginate hydrogel beads

In this study, controlled release formulations for reducing environmental impact of pesticides have been produced by encapsulating as a model pesticide carbaryl (Carb) in the alginate beads. The various hydrogel bead formulations were prepared by the ionotropic crosslinking of sodium alginate (NaAlg) with calcium and nickel ions. The surface morphology of prepared beads was characterized with scanning electron microscopy (SEM). SEM confirmed the spherical nature and surface morphology of the particles. Bead characteristics, such as carbaryl entrapment efficiency, particle size, equilibrium swelling degree, and carbaryl release kinetics, were determined. The effects of the bead preparation conditions such as crosslinker concentration and type, carbaryl/sodium alginate (Carb/NaAlg) ratio and percentage of NaAlg on the carbaryl release from the calcium alginate (Ca‐Alg) and nickel alginate (Ni‐Alg) beads were investigated in distilled water at 25°C. It was observed that carbaryl release from the Ca‐Alg beads was slower than that of Ni‐Alg beads. The release results indicated that carbaryl release from both of the Ca‐Alg and Ni‐Alg beads decreases with the increasing crosslinker concentration, Carb/NaAlg ratio and percentage of NaAlg. The highest carbaryl release was found to be 100% for the Ni‐Alg beads at 3 days whereas the lowest carbaryl release was found to be 67% for the Ca‐Alg beads at 21 days. The swelling measurements of the beads were also in consistent with the carbaryl release results. The carbaryl release from most of the bead formulations followed Case II transport. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and characterization of dual responsive sodium alginate‐g‐poly(vinyl alcohol) hydrogel

Poly(vinyl alcohol) (PVA) was chosen as a controllable gelator to prepare sodium alginate (SA)‐based physically cross‐linked dual‐responsive hydrogel by three steps. First, polyvinyl acetate (PVAc) was grafted onto SA via radical copolymerization. Then, the copolymer was subsequently converted into SA‐g‐poly(vinyl alcohol) (SAPVA) by alcoholysis reaction. PVA content of SAPVA was tailored by controlling the graft percentage of PVAc, i.e. through varying the amount of vinyl acetate during copolymerization. Finally, SAPVA hydrogels were formed by freezing‐thawing cycles. The structure of the graft copolymers was verified with FTIR spectroscopy. X‐ray diffraction analysis results revealed that the crystallinity of SAPVA hydrogels depended on the PVA content of SAPVA. The swelling test showed that SAPVA hydrogels were pH‐responsive, and the swelling was reversible. SAPVA hydrogels also behaved electric‐responsive. In addition, the pH‐sensitivity of SAPVA hydrogels was able to be controlled with the composition of the hydrogels. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphology and Property of Calcium Silicate Encapsulated with Alginate Beads

The alginate beads encapsulating calcium silicate were prepared. The morphologies and properties of the encapsulated beads were investigated. The beads were prepared by mixing modified calcium silicate with vinyltriethoxysilane in an alginate solution. The alginate-calcium silicate dispersion was dropped into a calcium chloride solution. The mean particle size of the resulting beads depended on the content of modified calcium silicate in alginate solution. In addition, the shape of the alginate gel was controlled by the viscosity of the alginate solution. The result showed that the calcium silicate particles were well dispersed within the matrix of the alginate. The thermal stability of the alginate beads encapsulating the calcium silicate increased with increasing the content of modified calcium silicate.     

Synthesis and characterization of alginate‐g‐vinyl sulfonic acid with a potassium peroxydiphosphate/thiourea system

Alginate‐g‐vinyl sulfonic acid graft copolymer was synthesized through the graft copolymerization of vinyl sulfonic acid (VSA) onto alginate with an efficient system, i.e., potassium peroxydiphosphate (PDP)/thiourea in an aqueous medium. The effects of the concentration of thiourea, PDP, hydrogen ion, alginate, and VSA along with the time and temperature on the graft copolymerization were studied by the determination of the grafting parameters (grafting ratio, add‐on, conversion, grafting efficiency, and homopolymer). The synthesized graft copolymer was characterized by FTIR analysis. Thermogravimetric analysis showed that the alginate‐g‐vinyl sulfonic acid is thermally more stable than alginate. Water swelling capacity, metal ion sorption, flocculation, and resistance to biodegradability studies of synthesized graft copolymer have been performed with respect to the parent polymer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and Characterization of Starch-Poly(vinyl Acetate) Graft Copolymers and their Saponified Form

A redox initiation system based on potassium persulfate/acetone sodium bisulphite (KPS/ASBS) was developed to initiate the graft copolymerization of vinyl acetate (VAc) monomer onto corn starch in aqueous solution. The grafting reaction was studied with respect to grafting yield (GY), grafting efficiency (GE) and total conversion (TC) and results obtained were compared with those a well-established redox initiation system namely potassium persulfate/sodium bisulphite (KPS/SBS). The effect of reaction variables such as redox initiator concentration, liquor ratio, reaction time and temperature as well as VAc concentration were investigated. The GY, GE and TC increased significantly with increase of the redox initiation concentration up to 8/16 mmol/l irrespective of the initiation system used. Moreover, optimal grafting was obtained at 60 ^○C for KPS/ASBS redox system and 70 ^○C for KPS/SBS redox system. Saponification of poly (vinyl acetate)-starch graft copolymers were effected using NaOH in three different bath media (n-hexane, acetone or methanol) to convert starch-g-poly(vinyl acetate) to starch-g-poly(vinyl alcohol). Higher extent of solubility in hot water of the saponified form was achieved by using a bath containing n-hexane/sodium hydroxide; however, increasing the graft yield higher than 26.3% decreases the solubility. The structures and thermal stability of starch, grafted starch copolymer and saponified grafted starch copolymer were characterized by infrared spectroscopy and thermogravimetric analysis. Moreover, the rheological behavior as well as sizing performance of the saponified grafted starch copolymers were evaluated and compared with the native starch and commercial polyvinyl alcohol.     

Production of bioethanol by immobilized Saccharomyces Cerevisiae onto modified sodium alginate gel

BACKGROUND: Microbial bioethanol production is an important option in view of the finite global oil reserves. Bioethanol fermentation was carried out using immobilized microorganisms (Saccharomyces cerevisiae, Zymomonas mobilis, Pichia stipitis, etc.), which has many advantages compared with the use of free cells. Various support materials have been used for bioethanol fermentation, and alginate gels have been one of the most widely used matrices for cell entrapment. The aim of this study was increased bioethanol production by Saccharomyces cerevisiae immobilized on alginate gels. First, N‐vinyl‐2‐pyrrolidone was grafted onto sodium alginate. Then, the properties of ethanol production were investigated using the matrix obtained. RESULTS: The performance of ethanol fermentation was affected by calcium chloride concentration, N‐vinyl‐2‐pyrrolidone grafted onto the sodium alginate, sugar concentration and the percentage of immobilized cell beads. These effects were optimized to give maximum ethanol production. Ethanol production was accelerated when sodium alginate polymer was modified with N‐vinyl‐2‐pyrrolidone. The maximum concentration, productivity and yield of ethanol were 69.68 g L^?1, 8.71 g L^?1 h^?1 and 0.697 g g^?1, respectively. CONCLUSION: The new polymeric matrix, when compared with sodium alginate, showed better ethanol production due to the hydrophilic property of N‐vinyl‐2‐pyrrolidone. The results suggest that the proposed method for immobilization of Saccharomyces cerevisiae has potential in industrial applications of the ethanol production process. Copyright © 2011 Society of Chemical Industry     

超临界二氧化碳协助双单体接枝聚丙烯

采用氧化法制备氢过氧化聚丙烯(HPP),然后用超临界二氧化碳(SC CO2)将单体苯乙烯(St)和季戊四醇三丙烯酸酯(PETA)溶胀到HPP颗粒内,再通过热引发将单体接枝到HPP上.考察了溶胀温度、压力、接枝反应温度、时间及单体用量对产物接枝率与单体接枝效率的影响,并采用红外光谱(FT-IR)、热重-差热分析(TG-DTA)、扫描电子显微镜(SEM)对接枝共聚物进行了表征.结果表明,合适的反应条件为30 g聚丙烯和0.5 g过氧化苯甲酰(BP0)在80℃反应2 h生成HPP,HPP与9 g苯乙烯(St)和季戊四醇三丙烯酸酯(PETA)的混合物(St与PETA物质的量之比为1:1)在37℃,8.5 MPa的超临界CO2中溶胀3 h,再在80℃常压下反应8 h,得到双单体接枝聚丙烯,接枝率达到28%,接枝效率大于90%,且PETA和St同时接枝到了PP分子链上,聚合物的耐热性增强.