Influence of pyrazole derivatives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized TiO2 solar cell performance

The influence of pyrazole additives in an I⁻/I₃⁻ redox electrolyte solution on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics of the cell were measured using 18 different pyrazole derivatives. All of the pyrazole additives enhanced the open-circuit photovoltage (V_oc) and the solar energy conversion efficiency (η), but reduced the short-circuit photocurrent density (J_sc). Most of the pyrazoles improved fill factor (ff). The physical and chemical properties of the pyrazoles were computationally calculated in order to elucidate the reasons for the additive effects on cell performance. The greater the partial charge of the nitrogen atom at position 2 in the pyrazole group, the larger the V_oc, but the smaller the J_sc values. As the dipole moment of the pyrazole derivatives increased, the V_oc value increased, but the J_sc value decreased. The V_oc of the cell also increased as the ionization energy of the pyrazoles decreased. These results suggest that the electron donicity of the pyrazole additives affected the interaction with the nanocrystalline TiO₂ photoelectrode, the I⁻/I₃⁻ electrolyte, and the acetonitrile solvent, which changed the Ru(II)-dye-sensitized solar cell performance.     

Influence of alkylaminopyridine additives in electrolytes on dye-sensitized solar cell performance

The influence of alkylaminopyridine additives on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile was studied. The current–voltage characteristics were measured for more than 20 different alkylaminopyridines under AM 1.5 (100 mW/cm²). The alkylaminopyridine additives tested had varying effects on the performance of the cell. All the additives decreased the short circuit photocurrent density (J_sc), but increased the open-circuit photovoltage (V_oc) of the solar cell. Molecular orbital calculations imply that the dipole moment of the alkylaminopyridine molecules influences the J_sc of the cell and that the size, solvent accessible surface area, and ionization energy all affect the V_oc of the cell. The highest V_oc of 0.88 V was observed in an electrolyte containing 4-pyrrolidinopyridine, which is comparable to the maximum V_oc of 0.9 V for a cell consisting of TiO₂ electrode and I⁻/I₃⁻ redox system.     

Influence of alkylpyridine additives in electrolyte solution on the performance of dye-sensitized solar cell

The influence of alkylpyridines additive to an I⁻/I₃⁻ redox electrolyte in acetonitrile on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell was studied. I–V measurements were performed using more than 30 different alkylpyridines. The alkylpyridine additives showed a significant influence on the performance of the cell. All the additives decreased the short-circuit photocurrent (J_sc), but most of the alkylpyridines increased the open-circuit photovoltage (V_oc) and fill factor (ff) of the solar cell. The results of the molecular orbital calculations suggest that the dipole moment of the alkylpyridine molecules correlate with the J_sc of the cell. These results also suggest that both the size and ionization energy of pyridines correlate with the V_oc of the cell. Under AM 1.5 (100 mW/cm²), the highest solar energy conversion efficiency (η) of 7.6% was achieved by using 2-propylpyridine as an additive, which was more effective than the previously reported additive, 4-t-butylpyridine.     

Density functional study of alkylpyridine–iodine interaction and its implications in the open-circuit photovoltage of dye-sensitized solar cell

A density functional theory (DFT) method was used to study the monomer and intermolecular charge-transfer complexes of 22 different alkylpyridines with diiodine. DFT calculations revealed that the σ* orbital of iodine interacts with the nitrogen lone pair in pyridines. The open-circuit photovoltage (V_oc) values of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized nanocrystalline TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile using alkylpyridines additive were compared to computational calculations on the interaction between pyridines and I₂ by a DFT method. The optimized geometries, frequency analyses, Mulliken population analyses, and interaction energies suggest that the V_oc value of the solar cell is higher, the more alkylpyridine complexes with I₂.     

Manufacturing method for transparent electric windows using dye-sensitized TiO2 solar cells

The transparent electric windows based on dye-sensitized nanocrystalline TiO₂ solar cells have been prepared. The solar cell consists of dye-sensitized TiO₂ electrode with a TiO₂ layer of an about 8 μm thickness and of a 80×80 mm² active area, Pt counter electrode and redox electrolyte. The solar cell shows a transmittance of approximately 60% in the visible range and an open-circuit voltage (V_oc) of 0.64 V and a short-circuit photocurrent (J_sc) of 250 mA. A moderately transparent electric window composed of nine unit solar cells in series generates V_oc of 5.7 V and J_sc of 220 mA at one sun light intensity.     

Influence of electrolyte on the photovoltaic performance of a dye-sensitized TiO2 solar cell based on a Ru(II) terpyridyl complex photosensitizer

We have investigated the influence of electrolyte composition on the photovoltaic performance of a dye-sensitized nanocrystalline TiO₂ solar cell (DSSC) based on a Ru(II) terpyridyl complex photosensitizer (the black dye). We have also spectroscopically investigated the interaction between the electrolyte components and the adsorbed dye. The absorption peaks attributed to the metal-to-ligand charge transfer transitions of the black dye in solution and adsorbed on a TiO₂ film, were red-shifted in the presence of Li cations, which led to an expansion of the spectral response of the solar cell toward the near-IR region. The photovoltaic performance of the DSSC based on the black dye depended remarkably on the electrolyte composition. We developed a novel efficient organic liquid electrolyte containing an imidazolium iodide such as 1,2-dimethyl-3-n-propylimidazolium iodide or 1-ethyl-3-methylimidazolium iodide (EMImI) for a DSSC based on the black dye. A high solar energy-to-electricity conversion efficiency of 9.2% (J_sc=19.0 mA cm⁻², V_oc=0.67 V, and FF=0.72) was attained under AM 1.5 irradiation (100 mW cm⁻²) using a novel electrolyte consisting of 1.5 M EMImI, 0.05 M iodine, and acetonitrile as a solvent with an antireflection film.     

Influence of electrolytes on the photovoltaic performance of organic dye-sensitized nanocrystalline TiO2 solar cells

We have studied the influence of electrolytes on the photovoltaic performance of mercurochrome-sensitized nanocrystalline TiO₂ solar cells using LiI, LiBr, and tetraalkylammonium iodides as the electrolyte. Short-circuit photocurrent density (J_sc) and open-circuit photovoltage (V_oc) depended strongly on the electrolyte. J_sc of 3.42 mA cm⁻² and V_oc of 0.52 V were obtained for the LiI electrolyte and J_sc of 2.10 mA cm⁻² and V_oc of 0.86 V were obtained for the Pr₄NI electrolyte. This difference in photovoltaic performance was due to the change in the conduction band level of the TiO₂ electrode. Large V_oc of 0.99 V was obtained for the LiBr electrolyte due to the large energy gap between the conduction band level of TiO₂ and the Br/Br₂ redox potential. Solar cell performance also depended strongly on organic solvent, suggesting that the physical properties of solvents such as Li ion conductivity and donor number affect photovoltaic performance.     

Temperature dependence and the oscillatory behavior of the opto-electronic properties of a dye-sensitized nanocrystalline TiO2 solar cell

A dye-sensitized TiO₂ solar cell was developed and characterized. The I–V (current–voltage) characteristics were studied at different temperatures from −40°C to 80°C. The opto-electronic properties of the cell depend on factors like ambient temperature and the time constants of the redox processes at the cell interfaces. The temperature dependence of V_oc and I_sc were clearly demonstrated. I_sc increased with increasing temperature above room temperature, where as V_oc increased with decreasing temperature below room temperature. The opto-electronic properties showed oscillatory behavior especially at low temperatures, which may be attributed to the different velocities of the redox processes occurring at the TiO₂/dye, dye/electrolyte and the electrolyte/counter electrode interfaces.     

Photoelectric behavior of nanocrystalline TiO2 electrode with a novel terpyridyl ruthenium complex

The photoelectric behavior of a black dye, tris (isothiocyanato)-[N-(2,2′:6′,2″-terpyridine-4′-(4-carboxylic acid) phenyl)] ruthenium (II) complex, was examined under different conditions. The dye was adsorbed on nanocrystalline TiO₂ surface strongly and generated incident monochromatic photon-to-current conversion efficiency (IPCE) of about 90% at maximum absorption wavelength and greater than 20% in the near-IR region. A sandwich-type solar cell fabricated by this dye-sensitized nanocrystalline TiO₂ film generated 6.1 mAcm⁻² of short-circuit photocurrent, 0.58 V of open-circuit photovoltage and 2.9% of overall yield under irradiation of white light (78.0 mWcm⁻²) from a Xe lamp. Since the title dye shows better photoresponse than the N3 dye in the near-IR region, it would be a promising panchromatic sensitizer after optimization.     

Highly efficient photon-to-electron conversion with mercurochrome-sensitized nanoporous oxide semiconductor solar cells

Dye-sensitized solar cells based on nanoporous oxide semiconductor thin films such as TiO₂, Nb₂O₅, ZnO, SnO₂, and In₂O₃ with mercurochrome as the sensitizer were investigated. Photovoltaic performance of the solar cell depended remarkably on the semiconductor materials. Mercurochrome can convert visible light in the range of 400–600 nm to electrons. A high incident photon-to-current efficiency (IPCE), 69%, was obtained at 510 nm for a mercurochrome-sensitized ZnO solar cell with an I⁻/I₃⁻ redox electrolyte. The solar energy conversion efficiency under AM1.5 (99 mW cm⁻²) reached 2.5% with a short-circuit photocurrent density (J_sc) of 7.44 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.52 V, and a fill factor (ff) of 0.64. The J_sc for the cell increased with increasing thickness of semiconductor thin films due to increasing amount of dye, while the V_oc decreased due to increasing of loss of injected electrons due to recombination and the rate constant for reverse reaction. Dependence of photovoltaic performance of mercurochrome-sensitized solar cells on semiconductor particles, light intensity, and irradiation time were also investigated. High performance of mercurochrome-sensitized ZnO solar cells indicate that the combination of dye and semiconductor is very important for highly efficient dye-sensitized solar cells and mercurochrome is one of the best sensitizers for nanoporous ZnO photoelectrode. In addition, a possibility of organic dye-sensitized oxide semiconductor solar cells has been proposed as well as one using metal complexes.     

DFT investigation of the TiO2 band shift by nitrogen-containing heterocycle adsorption and implications on dye-sensitized solar cell performance

A density functional theory (DFT) method (periodic DMol³) with full geometry optimization was used to investigate the adsorption of nitrogen-containing heterocycles such as 4-t-butylpyridine (TBP) and imidazole on a TiO₂ anatase (1 0 1) surface. Negative shifts of the TiO₂ Fermi level by N-containing heterocycle adsorption were observed. Imidazole adsorption shifted the Fermi level of TiO₂ more negatively than TBP. This shift corresponded to the enhancement of the open-circuit photovoltage (V_oc) and the reduction of the short-circuit photocurrent density (J_sc) in a dye-sensitized TiO₂ solar cell. We are the first to theoretically discover a TiO₂ band shift upon N-containing heterocycles adsorption, and have successfully related this shift to the effect as an additive in an electrolyte solution on dye-sensitized solar cell performance.     

Characterization of CuInSe2/CdS thin-film solar cells prepared using CBD

CuInSe₂/CdS thin-film heterojunction solar cells were fabricated entirely by chemical bath deposition technique. The illuminated J−V characteristics of the devices prepared with different thicknesses of CdS and CuInSe₂ were studied. The typical solar cell parameters obtained for the best cell are: V_oc = 365 mV, J_sc = 12 mA/cm², FF = 61%, and η = 3.1% under an illumination of 85 mW/cm² on a cell of active area 0.1 cm². The J−V and C−V characteristics under dark condition and the spectral response were also studied for the best cell. The diode quality factor obtained is 1.7.     

Facile fabrication of mesoporous TiO2 electrodes for dye solar cells: chemical modification and repetitive coating

A chemical dispersing technique for preparing a coating paste of TiO₂ nanoparticles is disclosed to fabricate mesoporous electrodes for dye-sensitized TiO₂ solar cells. The suspension of TiO₂ (P-25) powder was stirred in aqueous nitric acid at 80°C, and then evaporated to dryness, giving the nitric acid-adsorbed P-25 powder. The coating paste was obtained by mixing the nitric acid-adsorbed P-25 with PEG (M_w 20,000) as a porosity-controlling agent and cellulosic polymer as a thickener. The mesoporous TiO₂ films were fabricated on conducting glasses by repetitive coating and calcined at 500°C (30 min). The TiO₂ film obtained by the five times repetitive coating (20 μm thickness) resulted in the 1.4 times higher energy conversion efficiency of the dye-sensitized solar cells than that of the one time coating TiO₂ film (V_oc=690 mV, J_sc=12.2 mA/cm², the fill FACTOR=0.71 and η=6.0%).     

Hybrid solar cells based on MEH-PPV and thin film semiconductor oxides (TiO2, Nb2O5, ZnO, CeO2 and CeO2–TiO2): Performance improvement during long-time irradiation

Performance improvement of hybrid solar cells (HSC) applying five different thin film semiconductor oxides has been observed during long-time irradiation in ambient atmosphere. This behavior shows a direct relation between HSC and oxygen content from the environment. Photovoltaic devices were prepared as bi-layers of thin film semiconducting oxides (TiO₂, Nb₂O₅, ZnO, CeO₂–TiO₂ and CeO₂) and the polymer MEH-PPV, with a final device configuration of ITO/Oxide_{thin film}/MEH-PPV/Ag. The oxides were prepared as thin transparent films from sol–gel solutions. The photovoltaic cells were studied in ambient atmosphere by recording the initial values of open circuit voltage (V_oc) and current density (I_sc). Solar decay curves presented as the measurement of the short circuit current as a function of time, IV curves and photophysical analyses were also carried out for each type of device. Solar cells with TiO₂ thin films showed the best performance with maximum V_oc as high as −0.74 V and I_sc of 0.4 mA/cm². Solar decay analyses showed that the devices require a stabilization period of several hours in order to reach maximum performance. In the case of TiO₂, Nb₂O₅ and CeO₂–TiO₂, the maximum current density was observed after 15 h; for CeO₂, the maximum performance was observed after 30 h. The only exception was observed with devices applying ZnO in which the current density decreased drastically and degraded the polymer in just a couple of hours.     

Anchorage of N3 dye-linked polyacrylic acid to TiO2/electrolyte interface for improvement in the performance of a dye-sensitized solar cell

A synthetic route was developed to link N3 dye to polyacrylic acid (PAA) using ethylenediamine (en) as the linker. The resulting complex, PAA–en–N3, was then coated onto a TiO₂ film. The modified TiO₂ film electrode (hereafter PAA–en–N3/TiO₂), when used as the photoanode in a dye-sensitized solar cell (DSSC), exhibited enhanced solar energy conversion efficiency compared with that of the usual DSSC with the N3/TiO₂ film electrode. The increase in efficiency was attributed to the increased open-circuit voltage (V_oc) and short-circuit photocurrent (J_sc). The increase in V_oc was attributed to the formation of a hydrophobic PAA–en–N3 layer on the TiO₂/electrolyte interface, while the increase in J_sc was attributed to the additional dye acquired by the TiO₂ film from the PAA–en–N3 complex.     

Effect of a redox electrolyte in mixed solvents on the photovoltaic performance of a dye-sensitized solar cell

The effect of the iodide/triiodide redox electrolyte in various organic solvents on the photoelectrochemical properties of bis(tetrabutylammonium) cis-bis(thiocyanato)bis(4-carboxy-2,2′-bipyridine-4′-carboxylato)ruthenium(II)-sensitized nanocrystalline TiO₂ solar cells was studied. Solvents with large donor numbers dramatically enhanced the open-circuit voltage (V_oc), but usually reduced the short-circuit photocurrent density (J_sc). For a mixed solvent of tetrahydrofuran (THF) and acetonitrile, V_oc increased and the fill factor decreased with increasing THF concentration, but J_sc remained relatively constant. As the partial charge of the N or O atom of the solvent molecule increased, V_oc increased, but J_sc was unchanged up to a certain value of the partial charge (for THF, −0.46). For cells using 0.3 M 4-tert-butylpyridine and 20 vol% THF in the electrolyte, a short-circuit photocurrent density of 18.23 mA cm⁻², an open-circuit voltage of 0.73 V, a fill factor of 0.73, and an overall conversion efficiency of 9.74% were obtained.     

A technique to compare polythiophene solid-state dye sensitized TiO2 solar cells to liquid junction devices

In this communication, we report on a technique to fabricate solid-state polythiophene-based dye sensitized solar cells (DSSCs) that can be directly compared to analogous liquid junction devices. The device configuration is based on non-porous TiO₂ thin films and one of the three undoped polythiophene hole conductors: poly[3-(11 diethylphosphorylundecyl) thiophene], P3PUT, poly(4-undecyl-2,2′-bithiophene), P4UBT, or poly(3-undecyl-2,2′-bithiophene), P3UBT. These polymers were spin coated and cast from organic solutions onto the TiO₂ films. The dense TiO₂ thin films (ca. 30 nm) were deposited on conductive glass via facile spray pyrolysis and sol–gel techniques. After that, cis-(SCN)₂ Bis(2,2′ bipyridyl-4,4′-dicarboxylate) ruthenium(II) (a.k.a. Ru N3 dye) was adsorbed on the TiO₂ surface, and the polythiophenes were utilized as hole conductors in a simplified solar cell geometry. The results were compared to the control DSSC device made with dense TiO₂ and a liquid electrolyte, or 2,2′,7,7′-tetrakis(N,N-di-p-methoxyphenylamine)-9,9′-spirobifluorene (a.k.a. Spiro-MeOTAD). The polythiophenes exhibited bandgaps in the range 1.9–2.0 eV, and HOMO energy levels of approximately 5 eV (vs. vacuum). The P3PUT DSSC device exhibited an AM1.5 V_OC=0.8 V, a J_SC=0.1 mA/cm², as well as an IPCE=0.5–1%. The AM1.5 short-circuit photocurrents and quantum efficiencies for DSSCs made with the polythiophenes, the Spiro-MeOTAD and the standard liquid electrolyte (I⁻/I₃⁻) were found to be identical within the limits of experimental uncertainty and reproducibility. Our results indicate that a solid-state replacement to the liquid junction is not necessarily limited by the fundamental aspect of hole transfer, one of the three fundamental aspects that must be met for an efficient DSSC. Rather than suggest that P3UBT or P4UBT could be used to create efficient “organic solar cells” with the exclusion of the Ru dye, we suggest that transparent thiophene compounds could be attractive candidates for high-surface area solid-state DSSCs, and that the technique presented can be applied to other hole conductors. It can allow a verification of one of the things necessary for the DSSC, so that parallel studies using high-surface area materials can proceed with confidence.     

Blue sensitizers for solar cells: Natural dyes from Calafate and Jaboticaba

Blue-violet anthocyanins from Jaboticaba (Myrtus cauliflora Mart) and Calafate (Berberies buxifolia Lam) were employed as TiO₂ dye-sensitizers. Solar cells sensitized by Jaboticaba extracts achieved up to J_sc=9.0 mA cm⁻², V_oc=0.59 V, P_max=1.9 mW cm⁻² and ff=0.54, while for Calafate sensitized cells the values determined were up to J_sc=6.2 mA cm⁻², V_oc=0.47 V, P_max=1.1 mW cm⁻² and ff=0.36. Other natural dyes were evaluated without significant photocurrent, demonstrating that only selected extracts are capable of converting sunlight in electricity. The results obtained with extracts of Jaboticaba and Calafate show a successful conversion of visible light into electricity by using natural dyes as wide band-gap semiconductor sensitizers in dye-sensitized solar cells. It also represents an environmentally friendly alternative for dye-sensitized solar cells with low cost production and an excellent system for educational purposes.     

The influence of surface morphology of TiO2 coating on the performance of dye-sensitized solar cells

The optimization of solar energy conversion efficiency of dye-sensitized solar cells (DSSCs) was investigated by the tuning of TiO₂ photoelectrode's surface morphology. Double-layered TiO₂ photoelectrodes with four different structures were designed by the coating of TiO₂ suspension, incorporated with low and high molecular weight poly(ethylene glycol) as a binder. Among these four systems, P2P1, where P1 and P2 correspond to the molecular weight of 20,000 and 200,000, respectively, showed the highest efficiency under the conditions of identical film thickness and constant irradiation. This can be explained by the larger pore size and higher surface area of P2P1 TiO₂ electrode than the other materials as revealed by scanning electron microscopic (SEM) and Brunauer–Emmett–Teller (BET) analyses. Electrochemical Impedance Spectroscopy (EIS) analysis shows that P2P1 formulation displayed a smaller resistance than the others at the TiO₂/electrolyte interface. The best efficiency (η) of 9.04% with the short-circuit photocurrent density (J_sc) and open-circuit voltage (V_oc) of 18.9 mA/cm² and 0.74 V, respectively, was obtained for a solar cell by introducing the light-scattering particles to the TiO₂ nanoparticles matrix coated on FTO electrode having the sheet resistivity of 8 Ω/sq.     

Improvement of a-Si solar cell properties by using SnO2:F TCO films coated with an ultra-thin TiO2 layer prepared by APCVD

TiO₂-overcoated SnO₂:F transparent conductive oxide films were prepared by atmospheric pressure chemical vapor deposition (APCVD) and an effect of TiO₂ layer thickness on a-Si solar cell properties was investigated. The optical properties and the structure of the TiO₂ films were evaluated by spectroscopic ellipsometry and X-ray difractometry. a-Si thin film solar cells were fabricated on the SnO₂:F films over-coated with TiO₂ films of various thicknesses (1.0, 1.5 and 2.0 nm) and I–V characteristics of these cells were measured under 1 sun (100 mW/cm² AM-1.5) illumination. It was found that the TiO₂ film deposited by APCVD has a refractive index of 2.4 at 550 nm and anatase crystal structure. The conversion efficiency of the a-Si solar cell fabricated on the 2.0 nm TiO₂-overcoated SnO₂:F film increased by 3%, which is mainly attributed to an increase in open circuit voltage (V_oc) of 30 mV.