Thermoelectric Performance of Poly(3,4-Ethylenedioxy-thiophene)/Poly(Styrenesulfonate) Pellets and Films

The thermoelectric performance of poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) pellets and free-standing PEDOT/PSS films, prepared from PEDOT/PSS solution containing the additives dimethyl sulfoxide or ethylene glycol, have been systematically investigated. It has been found that the electrical conductivity of free-standing PEDOT/PSS films is invariably much higher than that of PEDOT/PSS pellets, while there is no distinct change in the Seebeck coefficient. The highest electrical conductivity of a free-standing PEDOT/PSS film can be up to 300 S cm⁻¹, five to six times higher than that of PEDOT/PSS pellets (55 S cm⁻¹). The thermal conductivity was measured over a wide temperature range, indicating that PEDOT/PSS has extremely low thermal conductivity. The figure of merit (ZT) of free-standing PEDOT/PSS films with good environmental stability can be up to 10⁻², an order of magnitude higher than that of pressed PEDOT/PSS pellets (10⁻³).     

Thermoelectric Performance Enhancement of Poly(3,4-ethylenedioxythiophene):Poly(styrenesulfonate) Composite Films by Addition of Dimethyl Sulfoxide and Urea

Significant enhancement of thermoelectric (TE) performance was observed for free-standing poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT: PSS) composite films obtained from a PEDOT:PSS aqueous solution by simultaneous addition of dimethyl sulfoxide (DMSO) and different concentrations of urea. The electrical conductivity was enhanced from 8.16?S?cm^?1 to over 400?S?cm^?1, and the maximum Seebeck coefficient reached a value of 18.81???V?K^?1 at room temperature. The power factor of the PEDOT:PSS composite films reached 8.81???W?m^?1?K^?2. The highest thermoelectric figure of merit (ZT) in this study was 0.024 at room temperature, which is at least one order of magnitude higher than most polymers and bulk Si. These results indicate that the obtained composite films are a promising thermoelectric material for applications in thermoelectric refrigeration and thermoelectric microgeneration.     

Organic Semiconductors for Thermoelectric Applications

The thermoelectric performance of thin films fabricated from two commercially available, highly conductive polymer formulations based on poly (3,4-ethylendioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) was investigated. In order to enhance the electrical conductivity, the high-boiling solvent dimethyl sulfoxide (DMSO) was added. By changing the content of DMSO the electrical conductivity was increased by a factor of two without changing the Seebeck coefficient or the thermal conductivity. We achieved ZT = 9.2 × 10⁻³ at room temperature upon the addition of 5 vol.% DMSO to the PEDOT:PSS formulation.     

Simultaneous Increases in Electrical Conductivity and Seebeck Coefficient of PEDOT:PSS Films by Adding Ionic Liquids into a Polymer Solution

The electrical conductivity and Seebeck coefficient of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films were simultaneously improved by adding an ionic liquid (IL) into a polymer solution of the polymers. The maximum electrical conductivity of such a PEDOT:PSS/IL film reached 174 S cm⁻¹, more than an order of magnitude higher than that of pure PEDOT:PSS film, and the maximum Seebeck coefficient was up to 30 μV K⁻¹, more than twice the value for pure PEDOT:PSS film. This behavior is different from conventional thermoelectric (TE) materials, whose TE properties are strongly correlated, such as increasing electrical conductivity with increasing carrier concentration, usually resulting in a logarithmic decrease in Seebeck coefficient. Atomic force microscopy images of the PEDOT:PSS/IL films indicated that the ILs induced formation of a particular three-dimensional structure of highly conducting PEDOT grains, resulting in improvement of the TE performance of PEDOT:PSS films.     

Enhanced power factor of poly (3,4-ethyldioxythiophene):poly (styrene sulfonate) (PEDOT:PSS)/RTCVD graphene hybrid films

The thermoelectric generator has been an attractive alternative power source to operate a wireless sensor node. Usually, inorganic compounds are most often used in thermoelectric devices, and hence, are extensively studied due to their superior thermoelectric performance. We have investigated a novel interfacial technique to fabricate a hybrid film of highly conductive PEDOT:PSS (poly 3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) and graphene. Organic materials PEDOT doped with PSS exhibits outstanding electrical properties due to its high conductivity, low bandgap, and energy migration. Furthermore, we utilized graphene fabricated by rapid thermal chemical vapor deposition (RTCVD) as a thermoelectric material. Our results show that the interfacial technique between substrate and hybrid film could be clearly improved due to the UV plasma treatment. The thermoelectric hybrid film of PEDOT:PSS and RTCVD graphene (P/RTG) exhibited an enhanced power factor of 56.28 μW m⁻¹ K⁻² with a Seebeck coefficient of 54.0 μV K⁻¹.     

High‐Conductivity Poly(3,4‐ethylenedioxythiophene):Poly(styrene sulfonate) Film and Its Application in Polymer Optoelectronic Devices

The conductivity of a poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) film can be enhanced by more than two orders of magnitude by adding a compound with two or more polar groups, such as ethylene glycol, meso‐erythritol (1,2,3,4‐tetrahydroxybutane), or 2‐nitroenthanol, to an aqueous solution of PEDOT:PSS. The mechanism for this conductivity enhancement is studied, and a new mechanism proposed. Raman spectroscopy indicates an effect of the liquid additive on the chemical structure of the PEDOT chains, which suggests a conformational change of PEDOT chains in the film. Both coil and linear conformations or an expanded‐coil conformation of the PEDOT chains may be present in the untreated PEDOT:PSS film, and the linear or expanded‐coil conformations may become dominant in the treated PEDOT:PSS film. This conformational change results in the enhancement of charge‐carrier mobility in the film and leads to an enhanced conductivity. The high‐conductivity PEDOT:PSS film is ideal as an electrode for polymer optoelectronic devices. Polymer light‐emitting diodes and photovoltaic cells fabricated using such high‐conductivity PEDOT:PSS films as the anode exhibit a high performance, close to that obtained using indium tin oxide as the anode.     

Highly improved thermoelectric performances of PEDOT:PSS/SWCNT composites by solvent treatment

Composites of poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) and single-wall carbon nanotube (SWCNT) were prepared by mixing aqueous dispersions of PEDOT:PSS and SWCNT at different weight ratios. By being soaked with DMSO for 2 min at room temperature, the PEDOT:PSS/SWCNT composite with an optimized SWCNT weight ratio of 74 wt% exhibited a high electric conductivity of 3800 S cm⁻¹ and a reasonable Seebeck coefficient of 28 μV K⁻¹, leading to a promising power factor of 300 μW m⁻¹ K⁻² and a hopeful ZT value of 0.13. Possible reasons for the highly improved properties are carefully discussed.     

Effect of PEDOT:PSS–molecule interface on the charge transport characteristics of the large-area molecular electronic junctions

We have studied the effect of the PEDOT:PSS–molecule contact on the electrical characteristics of molecular junctions consisting of N-alkanedithiol and naphthalenethiol molecules. In this study, we experimentally investigated the properties of PEDOT:PSS-interlayer molecular junctions as they depended on the two kinds of PEDOT:PSS films (the pure PEDOT:PSS film and the dimethyl sulfoxide (DMSO)-modified PEDOT:PSS film) and their thermal annealing treatment. We observed that the electrical properties of these molecular junctions are influenced by the morphology and conductivity of the PEDOT:PSS films and by the thermal treatment. In particular, the resistance of the PEDOT:PSS-interlayer molecular junctions depended on the kind of PEDOT:PSS film and the temperature, within the range of elevated temperatures (higher than room temperature) tested. These experimental results are explained by the change of the interfacial properties of the PEDOT:PSS–molecule contact, which are influenced by the morphology change of the PEDOT:PSS film and the removal of residual DMSO or water from the interface.     

Origin of unusual thermoelectric transport behaviors in carbon nanotube filled polymer composites after solvent/acid treatments

Composites made of poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and carbon nanotube (CNT) have shown unchanged or even increased thermopower when electrical conductivity was raised by altering the concentration of CNT and/or treating the composites with a polar solvent, dimethyl sulfoxide (DMSO) or an acid, formic acid (FA). Unlike typical adversely correlated thermopower and electrical conductivity, remarkable increases in electrical conductivity by the treatment did not decrease thermopower. Furthermore, it is necessary to use an optimum CNT concentration to maximize thermopower and the power factor. In this study, an intermediate CNT concentration of 6.7 wt% showed the highest thermopower and power factor unlike other reports with typical organic composites. The origin of the unusual transport properties was suggested by studying changes in the relative ratio of conducting PEDOT core and insulating PSS, morphology, and carrier concentration and mobility. Our results indicate that the PSS removal by DMSO and FA could alter the carrier transport barrier, and CNT-PEDOT:PSS-CNT junctions could increase thermopower for composites with a low CNT concentration by avoiding direct contacts between CNTs.     

Explaining the effects of processing on the electrical properties of PEDOT:PSS

By simultaneously measuring the Seebeck coefficient and the conductivity in differently processed PEDOT:PSS films, fundamental understanding is gained on how commonly used processing methods improve the conductivity of PEDOT:PSS. Use of a high boiling solvent (HBS) enhances the conductivity by 3 orders of magnitude, as is well-known. Simultaneously, the Seebeck coefficient S remains largely unaffected, which is shown to imply that the conductivity is improved by enhanced connectivity between PEDOT-rich filaments within the film, rather than by improved conductivity of the separate PEDOT filaments. Post-treatment of PEDOT:PSS films by washing with H₂SO₄ leads to a similarly enhanced conductivity and a significant reduction in the layer thickness. This reduction strikingly corresponds to the initial PSS ratio in the PEDOT:PSS films, which suggests removal and replacement of PSS in PEDOT:PSS by HSO₄⁻ or SO₄²⁻ after washing. Like for the HBS treatment, this improves the connectivity between PEDOT filaments. Depending on whether the H₂SO₄ treatment is or is not preceded by an HBS treatment also the intra-filament transport is affected. We show that by characterization of S and σ it is possible to obtain more fundamental understanding of the effects of processing on the (thermo)electrical characteristics of PEDOT:PSS.     

High efficiency bulk heterojunction organic solar cell by using high conductivity modified PEDOT: PSS as a buffer layer

In this paper,bulk heterojunction solar cells with poly-(3-hexylthiophene)(P3HT):[6,6]-phenyl-C61-butyric-acid-methylester(PCBM) as an active layer and modified poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(PEDOT:PSS) as a buffer layer are fabricated.The buffer layer is modified by adding 1% to 5% dimethyl sulfoxide(DMSO) into PEDOT:PSS solution before spin-coating.The conductivity of modified PEDOT:PSS and the performance of solar cells with modified PEDOT:PSS are measured.The highest conductivity of modified PEDOT:PSS with 4% DMSO can achieve 89.693 S/cm.The performance of organic solar cell with PEDOT:PSS modified by 4% DMSO is the best.The 4% DMSOmodified-PEDOT:PSS cell has a power conversion efficiency of 3.34%,V oc of 5.7 V,J sc of 14.56 mA/cm 2 and filling factor(FF) of 40.34%.     

Optimization of electrohydrodynamic-printed organic electrodes for bottom-contact organic thin film transistors

In this study, we investigate the optimization of printed (3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) as source/drain electrodes for organic thin film transistors (OTFTs) through electrohydrodynamic (EHD) printing process. The EHD-printed PEDOT:PSS electrodes should fulfill the prerequisites of not only high conductivity but also optimum surface tension for successful jetting. The conductivity of PEDOT:PSS was dramatically enhanced from 0.07 to 352 S/cm by the addition of dimethylsulfoxide (DMSO). To use the DMSO-treated PEDOT:PSS solution in the EHD printing process, its surface tension was optimized by the addition of surfactant (Triton X-100), which was found to enable various jetting modes. In the stable cone-jet mode, the patterning of the modified PEDOT:PSS solution was realized on the surface-functionalized SiO₂ substrates; the printed line widths were in the range 384 to 81 μm with a line resistance of 8.3 × 10³ Ω/mm. In addition, pentacene-based OTFTs employing the EHD-printed PEDOT:PSS as source and drain electrodes were found to exhibit electrical performances superior to an equivalent vacuum-deposited Au-based device.     

Improvement of Thermoelectric Properties of PEDOT/PSS Films by Addition of Gold Nanoparticles: Enhancement of Seebeck Coefficient

Thermoelectric properties of hybrid films composed of poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT/PSS) and gold nanoparticles (AuNPs) stabilized with 3-mercaptopropinoic acid (Au-MPA NPs) and 6-mercaptohexanoic acid (Au-MHA NPs) were investigated. Several factors such as the size and content of the AuNPs, and the chain length of the NP stabilizer were found to influence the thermoelectric properties of the hybrid film. The Seebeck coefficient can be raised by varying the size of the Au-MPA NPs or the content of Au-MHA NPs. The enhancement in the Seebeck coefficient is suggested to be a result of reduced carrier concentration due to the increased number of AuNPs. This could be the first report on the fact that AuNPs enhance the Seebeck coefficient in PEDOT/PSS hybrid films.     

Improvement of electrical conductivity of PEDOT:PSS films by 2-Methylimidazole post treatment

The electrical conductivity of poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films was significantly improved without losing the optical transparency by treating the films with solution of 2-Methylimidazole in ethanol. The maximum electrical conductivity of such a thin film reached 930 S cm⁻¹, more than 1150 order of magnitude higher than that of pure PEDOT:PSS film. The mechanism of conductivity enhancement of treated thin PEDOT:PSS films was explored by atomic force microscopy (AFM) and UV/VIS spectrophotometer. The AFM scans show that the surface of the 2-Methylimidazole treated PEDOT:PSS layer is smoother than that of the pristine PEDOT:PSS thin film. Improvement in the morphology, electrical and optical properties of PEDOT:PSS films makes them highly suitable for numerous applications in optoelectronic devices.     

Comparison of dimethyl sulfoxide treated highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) electrodes for use in indium tin oxide-free organic electronic photovoltaic devices

Indium tin oxide (ITO)-free organic photovoltaic (OPV) devices were fabricated using highly conductive poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the transparent conductive electrode (TCE). The intrinsic conductivity of the PEDOT:PSS films was improved by two different dimethyl sulfoxide (DMSO) treatments – (i) DMSO was added directly to the PEDOT:PSS solution (PEDOT:PSS_ADD) and (ii) a pre-formed PEDOT:PSS film was immersed in DMSO (PEDOT:PSS_IMM). X-ray photoelectron spectroscopy (XPS) and conductive atomic force microscopy (CAFM) studies showed a large amount of PSS was removed from the PEDOT:PSS_IMM electrode surface. OPV devices based on a poly(3-hexylthiophene):[6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM) bulk hetrojunction showed that the PEDOT:PSS_IMM electrode out-performed the PEDOT:PSS_ADD electrode, primarily due to an increase in short circuit current density from 6.62 mA cm⁻² to 7.15 mA cm⁻². The results highlight the importance of optimising the treatment of PEDOT:PSS electrodes and demonstrate their potential as an alternative TCE for rapid processing and low-cost OPV and other organic electronic devices.     

Direct Observation of Conductive Polymer Induced Inversion Layer in n‐Si and Correlation to Solar Cell Performance

Heterojunctions formed by ultrathin conductive polymer [poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonate)—PEDOT:PSS] films and n‐type crystalline silicon are investigated by photoelectron spectroscopy. Large shifts of Si 2p core levels upon PEDOT:PSS deposition provide evidence that a dopant‐free p–n junction, i.e., an inversion layer, is formed within Si. Among the investigated PEDOT:PSS formulations, the largest induced band bending within Si (0.71 eV) is found for PH1000 (high PEDOT content) combined with a wetting agent and the solvent additive dimethyl sulfoxide (DMSO). Without DMSO, the induced band bending is reduced, as is also the case with a PEDOT:PSS formulation with higher PSS content. The interfacial energy level alignment correlates well with the characteristics of PEDOT:PSS/n‐Si solar cells, where high polymer conductivity and sufficient Si‐passivation are also required to achieve high power conversion efficiency.     

In-plane conduction characterisation and charge transport model of DMSO co-doped,inkjet printed Poly(3,4-ethylenedioxythiophene): Polystyrene sulfonate (PEDOT:PSS)

The technologically important inkjet printed poly(3,4-ethylenedioxythiophene): polystyrene sulfonate (PEDOT:PSS) films, at different extents of co-doping with dimethyl sulfoxide DMSO, have been studied in terms of in-plane charge transport and electric field force microscopy (EFM). Similarly to past studies of spin coated PEDOT:PSS films, room temperature conductivity is enhanced by a factor of 10³ to 130 S cm⁻¹ on the addition of 5% DMSO, Hall probe analysis demonstrated a decrease in contact resistance from 10⁶ Ω to 10⁴ Ω whilst variable-temperature conductivity analysis shows an increase in the VRH exponent from 0.25 to 0.5 signifying a charge transport evolution from Mott Variable Range Hopping in 3-dimensions to a pseudo 1-dimensional Variable Range Hopping. In addition, electric field force microscopy (EFM) showed a corresponding threefold increase in PEDOT grain size. Further analysis was conducted to determine the hopping length and the ratio of the hopping length versus localization length in the electron transport model.     

A comparative assessment of surface microstructure and electrical conductivity dependence on co-solvent addition in spin coated and inkjet printed poly(3,4-ethylenedioxythiophene):polystyrene sulphonate (PEDOT:PSS)

This study focuses on the fabrication of poly(3,4-ethylenedioxythiophene):polystyrene sulphonate (PEDOT:PSS) thin films by inkjet printing and investigates the developed surface morphology and electrical conductivity of the printed films as a function of the concentration of dimethyl sulfoxide (DMSO), added as conduction enhancing co-solvent, and Surfynol, added as a surfactant. The printed films are compared with PEDOT:PSS films fabricated by the traditional spin coating technique. Measurements of the surface tension justify including surfactant as a processing additive, where addition of 1% Surfynol results in substantial decrease of the surface tension of the PEDOT:PSS solution, whilst it also increases film surface roughness by an order of magnitude for both fabrication methods. The addition of 5 wt% DMSO is shown to result in a 10³ decrease in sheet resistance for both spin coated and inkjet printed films with both processing routes demonstrating decrease in surface roughness and coarsening of PEDOT grains as a function of the co-solvent concentration, whilst X-ray photon spectroscopy showed an increase in the surface PEDOT to PSS ratio from 0.4 to 0.5. Inkjet printed films have lower sheet resistance than the corresponding spin coated films, whilst atomic force microscopy reveals a coarser surface morphology for the inkjet printed films. The findings in this work point out at the decrease of sheet resistance due to coarsening of PEDOT grains which is linked to a decrease of surface roughness for small RMS values associated with the PEDOT grains. However, the higher surface roughness generated when Surfynol surfactant was added was not detrimental to the film’s in-plane conductivity due to the fact that these higher roughness values were unrelated to the PEDOT grains.     

Plasticization of PEDOT:PSS by Common Additives for Mechanically Robust Organic Solar Cells and Wearable Sensors

Despite the ubiquity of poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) in applications demanding mechanical flexibility, the effect on the mechanical properties of common additives—i.e., dimethylsulfoxide (DMSO), Zonyl fluorosurfactant (Zonyl), and poly(ethyleneimine) (PEI)—has not been reported. This paper describes these effects and uses plasticized films in solar cells and mechanical sensors for the detection of human motion. The tensile moduli of films spin‐coated from solutions containing 0%, 5%, and 10% DMSO and 0.1%, 1%, and 10% Zonyl (nine samples total) are measured using the buckling technique, and the ductility is inferred from measurements of the strain at which cracks form on elastic substrates. Elasticity and ductility are maximized in films deposited from solutions containing 5% DMSO and 10% Zonyl, but the conductivity is greatest for samples containing 0.1% Zonyl. These experiments reveal enlargement of presumably PEDOT‐rich grains, visible by atomic force microscopy, when the amount of DMSO is increased from 0% to 5%. PEI—which is used to lower the work function of PEDOT:PSS—has a detrimental effect on the mechanical properties of the PEDOT:PSS/PEI bilayer films. Wearable electronic sensors employing PEDOT:PSS films containing 5% DMSO and 10% Zonyl are ­fabricated, which exhibit detectable responses at 20% strain and high mechanical robustness through elastic deformation.